grundfos sp 14-4 pump : sp14- 4 rp2 4'1x230/50 1.10kw … · printed from grundfos product centre...
TRANSCRIPT
-
GRUNDFOS DATA BOOKLET
SP14- 4 Rp2 4"1X230/50 1.10kW Grundfos Pump 98699336
Thank you for your interest in our productsPlease contact us for more information, or visit our websitehttps://www.lenntech.com/grundfos/SPFAM/98699336/SP-14-4.html
[email protected]. +31-15-261.09.00fax. +31-15-261.62.89
BE > THINK > INNOVATE
-
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. Description1 SP 14-4
Product No.: 98699336
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically orhorizontally. All steel components are made in stainless steel, EN 1.4301 (AISI 304), that ensures highcorrosive resistance. This pump carries drinking water approval.The pump is fitted with a 1.1 kW MS402 motor with sand shield, lip seal, water-lubricated journalbearings and a volume compensating diaphragm. The motor is a canned type submersible motoroffering good mechanical stability and high efficiency. Suitable for temperatures up to 40 °C.The motor is not fitted with a temperature sensor. If temperature monitoring is desired, a Pt1000 sensorcan be fitted.The motor is for direct-on-line starting (DOL).
Further product detailsThe pump is suitable for applications similar to the following:
- raw-water supply- irrigation- groundwater lowering- pressure boosting- fountain applications.
The Grundfos SP pump is renowned for its high efficiency and already complies with the requirementsof the Minimum Efficiency Index, and therefore Grundfos is amongst the best in class withinsubmersible pumps.
PumpAll pump surfaces that are in contact with pumped liquids are made in stainless steel which makesthem corrosion- and wear-resistant. The corrosion diagram below shows the capabilities of the pumpand motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm(x-axis).
The elastomer parts in the pump offer good wear resistance and long service intervals. The bearingsare made of LSR (Liquid Silicone Rubber), sealing rings are made of TPU (ThermoplasticPoly-Urethane) and the non-return valve is made of NBR (Nitrile-Butadiene Rubber). The specialelastomer material of the bearings offers increased resistance to sand and other abrasive particles(from 50 to 150 mg/l).
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfosoffers FKM rubber parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
http://product-selection.grundfos.com/product-detail.html?productnumber=98699336&freq=50&lang=ENU
-
Printed from Grundfos Product Centre [2018.02.043]
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the pump isinevitable, the pump design allows for easy replacement of all internal wear parts (bearings, impeller, wear rings andseal rings) to maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. Thesuction interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
MotorThe stator is hermetically encapsulated in stainless steel and the windings are embedded in polymercompound. This results in high mechanical stability, optimum cooling and reduces the risk of shortcircuits in the windings.The shaft seal is of the lip seal type characterised by low friction against the rotor shaft. The NBRelastomer offers good wear resistance, good elasticity and resistance to particles. The rubber materialis approved for use in potable water.The motor can be fitted with a Pt100 or Pt1000 sensor that together with a control unit ensures that themaximum operating temperature conditions are not exceeded.
Liquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³
Technical:Speed for pump data: 2900 rpmRated flow: 14 m³/hRated head: 16.5 mShaft seal for motor: LIPSEALApprovals on nameplate: CE,EACCurve tolerance: ISO9906:2012 3BMotor version: T40
Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: RP2Motor diameter: 4 inch
Electrical data:Motor type: MS402Type of motor: CSCRRated power - P2: 1.1 kWPower (P2) required by pump: 1.1 kWMains frequency: 50 HzRated voltage: 1 x 230 VRated current: 7.3 AStarting current: 480 %Cos phi - power factor: 0.99Rated speed: 2860 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): BBuilt-in temp. transmitter: no
Others:
-
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. DescriptionMinimum efficiency index, MEI ≥: 0.50ErP status: EuP Standalone/Prod.Net weight: 18.7 kgGross weight: 20.4 kgShipping volume: 0.016 m³
-
Printed from Grundfos Product Centre [2018.02.043]
98699336 SP 14-4 50 HzH
[m]
0
2
4
6
8
10
12
14
16
18
20
22
24
26
Q [m³/h]0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
eta[%]
0
10
20
30
40
50
60
70
80
90
100
SP 14-4, 1*230 V, 50Hz
P[W]
0
100
200
300
400
500
600
700
800
900
1,000
1,100
1,200
1,300
1,400
1,500
P1
P2
-
Printed from Grundfos Product Centre [2018.02.043]
H[m]
0
2
4
6
8
10
12
14
16
18
20
22
24
26
Q [m³/h]0 2 4 6 8 10 12 14 16
eta[%]
0
10
20
30
40
50
60
70
80
90
100
SP 14-4, 1*230 V, 50Hz
P[W]
0
200
400
600
800
1,000
1,200
1,400 P1
P2
95
387
538
925
101RP2
GN
Grey
Brown
Black
Yellow/green
3
2
1 L1
N
PE
L
N
SA-SPM 3
M1
Description ValueGeneral information:Product name: SP 14-4Product No: 98699336EAN number: 5712600111554Technical:Speed for pump data: 2900 rpmRated flow: 14 m³/hRated head: 16.5 mStages: 4Impeller reduc.: NONEShaft seal for motor: LIPSEALApprovals on nameplate: CE,EACCurve tolerance: ISO9906:2012 3BModel: AValve: YESMotor version: T40Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: RP2Motor diameter: 4 inchLiquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³Electrical data:Motor type: MS402Type of motor: CSCRApplic. motor: NEMARated power - P2: 1.1 kWPower (P2) required by pump: 1.1 kWMains frequency: 50 HzRated voltage: 1 x 230 VRated current: 7.3 AStarting current: 480 %Cos phi - power factor: 0.99Rated speed: 2860 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): BMotor protec: CONTACTThermal protec: internalBuilt-in temp. transmitter: noMotor No: 79213105Others:Minimum efficiency index, MEI ≥: 0.50ErP status: EuP Standalone/Prod.Net weight: 18.7 kgGross weight: 20.4 kgShipping volume: 0.016 m³
95
101
RP2
GN
http://product-selection.grundfos.com/product-detail.html?productnumber=98699336&freq=50&lang=ENU
-
Printed from Grundfos Product Centre [2018.02.043]
98699336 SP 14-4 50 Hzcos phi
eta
0.0
0.2
0.4
0.6
0.8
P2 [kW]0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
I[A]
0
2
4
6
8
SP14-4 + MS402 1.1 kW 1*230 V, 50 Hz
eta
cos phi
I
n[rpm]
2000
2200
2400
2600
2800
P1[kW]
0.0
0.4
0.8
1.2
1.6n
P1
-
Printed from Grundfos Product Centre [2018.02.043]
98699336 SP 14-4 50 Hz
Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.
95
387
538
925
101RP2
GN
-
Printed from Grundfos Product Centre [2018.02.043]
98699336 SP 14-4 50 Hz
Note! All units are in [mm] unless others are stated.
Gre
y
Brow
n
Blac
k
Yello
w/g
reen
321L1 N PE
L N
SA-S
PM 3
M 1
-
Disclaimer: The information about the Grundfos pump in this document may be outdated.Data may be subject to alterations without further notice.Please contact us to verify the data above is still accurate/up-to-date.
All information is copyright Grundfos.
[email protected]. +31-15-261.09.00fax. +31-15-261.62.89