gtp no-111112-1881
TRANSCRIPT
-
7/28/2019 GTP NO-111112-1881
1/7
DAMAN
S.No Particulars 3 X 6 3 X 10 2 X 70 2 X 150 3
1 Name of Manufacturer
2 Type of cable AYWY AYWY AYFY AYFY
3 Voltage Grade V
4 No of cores X size in sqmm 3 X 6 3 X 10 2 X 70 2 X 150 3
5 Conductor
a) Material
b) Max. d.c. resistance of conductor at 20 C
(ohm/km)4.61 3.08 0.443 0.206
c) Shape of the conductor
Stranded
Circular
Stranded
CircularStranded Sector Stranded Sector Stran
6 Insulationa) Material
b) Nominal thickness (mm) 1.0 1.0 1.4 1.8
7 Inner Sheath
a) Material
b) Minimum thickness (mm) 0.3 0.3 0.3 0.4
8 Armouring
a) Material Gal.Steel Gal.Steel Gal.Steel Gal.Steel G
b) Type of armouring Round Wire Round Wire Flat Strip Flat Strip Fl
c) Nominal size of armour (mm) 1.40 1.40 4.0 x 0.8 4.0 x 0.8 4
9 Outer Sheath
a) Material
b) Thickness (mm) 1.24 (Min.) 1.40 (Min.) 1.56 (Min.) 1.72 (Min.) 1.4
10 Electrical Parameters
a) Max. a.c. resistance of conductor at 70C
(ohm/km)5.54 3.70 0.533 0.248
b) Calculated Cable reactance (ohm/km) 0.0954 0.0907 0.0771 0.0745 0
c) Impedance of cable (ohm/km) 5.54 3.70 0.538 0.259
d Approx. Cable Capacitance (mfd/km) 0.58 0.67 1.14 1.28
11 Maximum conductor temperature under
normal operating conditions
12 Maximum conductor temperature at the
termination of short circuit
13 Short Circuit rating of conductor for the duration
of 1 sec (kA)0.46 0.76 5.32 11.40
14 Continuous Current carrying capacities for
standard conditions :-
(a) In Ground at 30C (A) 35 46 160 240
(b) In Air at 40C (A) 30 40 150 240
15 Applicable Standard
16
Approx. overall diameter of the cable in mm18.5 2.0 20.5 2.0 27.5 2.0 35.5 2.0 19
17 Minimum bending radius
18 Max. Tensile strength
(i) for Cables pulled with stocking (Newtons)
ii) for Cables pulled with pulling eyes (N) 540 900 4,200 9,000
19 Colour of outer sheath.
ROHINI
GTP NO-111112-1881
Note:-The values given above are subject to tolerances as per the relevant standards.
Technical Particulars of LT PVC Cables
IS 8130/84,IS 155
-
7/28/2019 GTP NO-111112-1881
2/7
Technical Particulars of LT PVC Cables
DAMAN
S.No Particulars 1 X 630
1 Name of Manufacturer Polycab Wires Pvt. Ltd, Daman
2 Type of cable AYFaY
3 Voltage Grade V 1100
4 No of cores X size in sqmm 1 X 630
5 Conductora) Material H2/H4 Grade Aluminium to IS: 8130/1984
b) Max. d.c. resistance of conductor at 20 C
(ohm/km)0.0469
c) Shape of the conductor Stranded Circular
6 Insulation
a) Material PVC Type 'A' as per IS:5831/84
b) Nominal thickness (mm) 3.9
7 Inner Sheath
a) Material NA
b) Minimum thickness (mm) 0
8 Armouring
a) Material Aluminium
b) Type of armouring Flat Stripc) Nominal size of armour (mm) 4.0 x 0.8
9 Outer Sheath
a) Material FRLS 'PVC Type 'ST1' as per IS:5831/84
b) Thickness (mm) 1.72 (Min.)
10 Electrical Parameters
a) Max. a.c. resistance of conductor at 70C
(ohm/km)0.0606
b) Calculated Cable reactance (ohm/km) 0.0828
c) Impedance of cable (ohm/km) 0.103
d Approx. Cable Capacitance (mfd/km) 1.44
11 Maximum conductor temperature under
normal operating conditions70C
12 Maximum conductor temperature at the
termination of short circuit160C
13 Short Circuit rating of conductor for the duration
of 1 sec (kA)47.90
14 Continuous Current carrying capacities for
standard conditions :-
(a) In Ground at 30C (A) 390
(b) In Air at 40C (A) 550
15 Applicable Standard IS 8130/84,IS 1554 Part I/88, IS 5831/84, IS 3975/88
etc. with latest up to date amendments
16
Approx. overall diameter of the cable in mm43.5 2.0
17 Minimum bending radius 15 times Overall diameter18 Max. Tensile strength
(i) for Cables pulled with stocking (Newtons) 9 x D, D is the cable OD in mm
ii) for Cables pulled with pulling eyes (N) 18,900
19 Colour of outer sheath. Black
ROHINI
Note:-The values given above are subject to tolerances as per the relevant standards.
GTP NO-111112-1881
-
7/28/2019 GTP NO-111112-1881
3/7
DAMAN
S.No Particulars 2 X 4 3 X 2.5 4 X
1 Name of Manufacturer
2 Type of cable YWY YWY Y3 Voltage Grade V
4 No of cores X size in sqmm 2 X 4 3 X 2.5 4 X
5 Conductor
a) Material
b) Max. d.c. resistance of conductor at 20 C
(ohm/km) 4.61 7.41 1
c) Shape of the conductor
Stranded
Circular
Stranded
Circular
Str
Cir
6 Insulation
a) Material
b) Nominal thickness (mm) 1.0 0.9
7 Inner Sheath
a) Materialb) Minimum thickness (mm) 0.3 0.3
8 Armouring
a) Material Gal.Steel Gal.Steel Ga
b) Type of armouring Round Wire Round Wire Roun
c) Nominal size of armour (mm) 1.40 1.40 1
9 Outer Sheath
a) Material
b) Thickness (mm) 1.24 Min. 1.24 Min. 1.24
10 Electrical Parameters
a) Max. a.c. resistance of conductor at 70C
(ohm/km) 5.52 8.87 1
b) Calculated Cable reactance (ohm/km) 0.102 0.106 0
c) Impedance of cable (ohm/km) 5.52 8.87 1
d Approx. Cable Capacitance (mfd/km) 0.48 0.44 0
11 Maximum conductor temperature under normal
operating conditions
12 Maximum conductor temperature at the
termination of short circuit
13 Short Circuit rating of conductor for the duration
of 1 sec (kA) 0.46 0.29 0
14 Continuous Current carrying capacities for
standard conditions :-
(a) In Ground at 30C (A) 41 27
(b) In Air at 40C (A) 35 24
15 Applicable Standard
16
Approx. overall diameter of the cable in mm16.0 2.0 15.0 2.0 14.5
17 Minimum bending radius
18 Max. Tensile strength
(i) for Cables pulled with stocking (Newtons)
ii) for Cables pulled with pulling eyes (N) 400 375 3
19 Colour of outer sheath.
ROHINI
Technical Particulars of LT PVC Cab
Note:-The values given above are subject to tolerances as per the relevant standards.
GTP NO-111112-1881
-
7/28/2019 GTP NO-111112-1881
4/7
DAMAN
S.No Particulars 3 X 10 3 X 16 3 X 25 3 X
1 Name of Manufacturer
2 Type of cable AYWY AYFY AYFY AY
3 Voltage Grade V
4 No of cores X size in sqmm 3 X 10 3 X 16 3 X 25 3 X5 Conductor
a) Material
b) Max. d.c. resistance of conductor at 20 C
(ohm/km)3.08 1.91 1.20 0.8
c) Shape of the conductor
Stranded
CircularStranded Sector Stranded Sector Strande
6 Insulation
a) Material
b) Nominal thickness (mm) 1.0 1.0 1.2 1
7 Inner Sheath
a) Material
b) Minimum thickness (mm) 0.3 0.3 0.3 0
8 Armouringa) Material Gal.Steel Gal.Steel Gal.Steel Gal.
b) Type of armouring Round Wire Flat Strip Flat Strip Flat
c) Nominal size of armour (mm) 1.40 4.0 x 0.8 4.0 x 0.8 4.0
9 Outer Sheath
a) Material
b) Thickness (mm) 1.40 (Min.) 1.40 (Min.) 1.40 (Min.) 1.40
10 Electrical Parameters
a) Max. a.c. resistance of conductor at 70C
(ohm/km)3.70 2.29 1.44 1.
b) Calculated Cable reactance (ohm/km) 0.0907 0.0862 0.0853 0.0
c) Impedance of cable (ohm/km) 3.70 2.30 1.44 1.
d Approx. Cable Capacitance (mfd/km) 0.67 0.80 0.84 0.11 Maximum conductor temperature under
normal operating conditions
12 Maximum conductor temperature at the
termination of short circuit
13 Short Circuit rating of conductor for the duration
of 1 sec (kA)0.76 1.22 1.90 2.
14 Continuous Current carrying capacities for
standard conditions :-
(a) In Ground at 30C (A) 46 60 76 9
(b) In Air at 40C (A) 40 51 70 8
15 Applicable Standard
16
Approx. overall diameter of the cable in mm20.5 2.0 19.0 2.0 22.0 2.0 23.5
17 Minimum bending radius
18 Max. Tensile strength
(i) for Cables pulled with stocking (Newtons)
ii) for Cables pulled with pulling eyes (N) 900 1,440 2,250 3,1
19 Colour of outer sheath.
ROHINI
Technical Particulars of LT PVC Cables
Polycab Wires Pvt. Ltd, D
1100
H2/H4 Grade Aluminium to IS
PVC Type 'A' as per IS:58
Extruded PVC Type ST1 to I
'PVC Type 'ST1' as per IS:
70C
160C
IS 8130/84,IS 1554 Part I/88, IS 5831/84, IS 3975/88
12 times Overall diam
9 x D, D is the cable OD
Black
Note:-The values given above are subject to tolerances as per the relevant standards.
GTP NO-111112-1881
-
7/28/2019 GTP NO-111112-1881
5/7
DAMAN
S.No Particulars 3 X 2.5 5 X 1.5 12 X 1.5 19 X 1.5
1 Name of Manufacturer
2 Type of cable YWY YWY YWY YWY
3 Voltage Grade V
4 No of cores X size in sqmm 3 X 2.5 5 X 1.5 12 X 1.5 19 X 1.5
5 Conductor
a) Material
b) Max. d.c. resistance of conductor at 20 C
(ohm/km)7.41 12.1 12.1 12.1
c) Shape of the conductor
Stranded
Circular
Stranded
Circular
Stranded
Circular
Stranded
Circular
6 Insulation
a) Material
b) Nominal thickness (mm) 0.9 0.8 0.8 0.8
7 Inner Sheath
a) Material
b) Minimum thickness (mm) 0.3 0.3 0.3 0.3
8 Armouring
a) Material Gal.Steel Gal.Steel Gal.Steel Gal.Steel
b) Type of armouring Round Wire Round Wire Round Wire Round Wire
c) Nominal size of armour (mm) 1.40 1.40 1.60 1.60
9 Outer Sheath
a) Material
b) Thickness (mm) 1.24 (Min.) 1.24 (Min.) 1.40 (Min.) 1.40 (Min.)
10 Electrical Parameters
a) Max. a.c. resistance of conductor at 70C
(ohm/km)8.87 14.5 14.5 14.5
b) Calculated Cable reactance (ohm/km) 0.106 0.110 0.110 0.110
c) Impedance of cable (ohm/km) 8.87 14.5 14.5 14.5
d Approx. Cable Capacitance (mfd/km) 0.44 0.40 0.40 0.40
11 Maximum conductor temperature under
normal operating conditions
12 Maximum conductor temperature at the
termination of short circuit
13 Short Circuit rating of conductor for the duration
of 1 sec (kA)0.29 0.17 0.17 0.17
14 Continuous Current carrying capacities for
standard conditions :-
(a) In Ground at 30C (A) 27 21 12 10
(b) In Air at 40C (A) 24 17 10 9
15 Applicable Standard
16Approx. overall diameter of the cable in mm
15.0 2.0 15.5 2.0 20.5 2.0 23.5 2.0
17 Minimum bending radius
18 Max. Tensile strength
(i) for Cables pulled with stocking (Newtons)
ii) for Cables pulled with pulling eyes (N) 375 375 900 1,425
19 Colour of outer sheath.
ROHINI
GTP NO-111112-1881
Technical Particulars of LT PVC Cables
Polycab Wires Pvt. Ltd, Daman
1100
Plain annealed Copper to IS:8130/1984
PVC Type 'A' as per IS:5831/84
Extruded PVC Type ST1 to IS:5831/84
PVC Type 'ST1' as per IS:5831/84
70C
160C
IS 8130/84,IS 1554 Part I/88, IS 5831/84, IS 3975/88 etc. with
latest up to date amendments
12 times Overall diameter
9 x D, D is the cable OD in mm
Black
Note:-The values given above are subject to tolerances as per the relevant standards.
-
7/28/2019 GTP NO-111112-1881
6/7
-
7/28/2019 GTP NO-111112-1881
7/7
DAMAN
S.No Particulars 1 X 630 3 X 185
1 Name of Manufacturer
2 Type of Cable 2XFaY 2XFY
3 Voltage Grade kV 3.8/6.6 3.8/6.6
4 No of cores X size in sqmm 1 X 630 3 X 185
5 a) Maximum conductor temperature under
normal operating conditions
b) Maximum conductor temperature at the
termination of short circuit
6 a) Permissible Voltage Variation
b) Permissible Frequency Variation
c) Combined Voltage & Frequency variation
7 Conductor
a) Material
b) Maximum d.c. resistance of conductor at 20 C
(ohm/km)0.0283 0.0991
c) Shape
8 Conductor Screening
a) Material
b) Nominal thickness (mm) 0.3 0.3
9 Insulation
a) Material
b) Nominal thickness (mm) 3.5 2.8
10 Insulation Screening
(i) Non - Metallic
a) Material
b) Nominal thickness (mm) 0.3 0.3
(ii) Metallic
a) Material
b) Approximate thickness (mm) NA 0.045
11 Inner Sheath
a) Material NA Extruded PVC Type ST2 toIS:5831/84
b) Minimum thickness (mm) 0 0.6
12 Armouring
a) Material Aluminium Gal.Steel
b) Type of armouring Flat Strip Flat Strip
c) Nominal size of armour (mm) 4.0 x 0.8 4.0 x 0.8
13 Outer Sheath
(i) Material
(ii) Thickness (mm) 1.72 (Min.) 2.20 (Min.)
14 Electrical Parameters
a) Max. a.c. resistance of conductor at 90 C
(ohm/km)0.0419 0.128
b) Approx. Cable Capacitance (mfd/km) 0.64 0.46c) Approx. Cable reactance (ohm/km) 0.0845 0.0858
d) Impedance of cable (ohm/km) 0.0943 0.154
15 Continuous Current carrying capacities :-
(a) In Ground (A) 680 350
(b) In Air (A) 1030 430
16 Short Circuit rating of conductor for the duration
of 1 sec (kA)90.14 26.47
17 Standard to which the cables confirm
18 Approx. Overall diameter (mm) 46.0 2.0 60.0 3.0
ROHINI
IS 8130/84,IS 7098 Part 2/85, IS 5831/84, IS 3975/88
etc. with latest up to date amendments
GTP NO-111112-1881
Note:-The values given above are subject to tolerances as per the relevant standards.
Polycab Wires Pvt. Ltd, Daman
5%
Extruded Semi-conducting Compound
XLPE as per IS 7098(Pt-2)/85, latest
Extruded Semi-conducting Compound
Copper Tape
Stranded Compact Circular
FRLS PVC Type 'ST2' as per IS:5831/84
Plain annealed Copper as per Class 2 of IS:8130/84
Technical Particulars of HT XLPE Cables
90C
250C
10%
10%