hand molding demonstration process
DESCRIPTION
Hand Molding Demonstration Process METRANSCRIPT
![Page 1: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/1.jpg)
HAND MOLDING DEMOSTRATION PROCESSGONZALVO, Zaira D.
![Page 2: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/2.jpg)
Different tools used in Hand Molding Ramming Venting Sprue making Riser putting Putting powder in parting line Gate Making Cores placement Safety and Precautions
![Page 3: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/3.jpg)
MOLDING is the process of manufacturing by shaping
pliable raw material using a rigid frame
![Page 4: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/4.jpg)
TOOLS USED IN HAND MOLDING
![Page 5: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/5.jpg)
TOOLS USED IN HAND MOLDING
o FLASKS are wood or metal frames in which the mold is made.
BELLOWS are used to blow excess parting materials from the pattern and also to blow loose sand and dirt from the mold cavity.
![Page 6: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/6.jpg)
TOOLS USED IN HAND MOLDING RIDDLES are used for sifting the
sand over the surfaces of the pattern. The size of the riddle is given by the number of meshes to the inch.
RAMMERS used to compress the moulding sand
![Page 7: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/7.jpg)
TOOLS USED IN HAND MOLDING STRIKE-OFF BAR are used
to scrape the extra sand from the top of the cope or drag after ramming.
DRAW SPIKES are tapered steel rods having a loop at one end and a sharp point at the other. to draw pattern from the
mold
![Page 8: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/8.jpg)
TOOLS USED IN HAND MOLDING TROWELS are made of
iron and wooden handle. for making joints for finishing, smoothing cutting ingates Giving shape Repairing molds
VENT WIRES – Thin steel rod or wire used for making holes(vents) in the rammed sand molds
![Page 9: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/9.jpg)
TOOLS USED IN HAND MOLDING SWAB is a small brush
having long hemp fibers used for applying water around the edges of a pattern
SHOVEL is like a rectangular pan fitted with a handle used for mixing the molding sand and for moving it from one place to the other.
![Page 10: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/10.jpg)
TOOLS USED IN HAND MOLDING CLAMPS are used to hold
the cope and drag of the complete mold together so that the cope may not float or rise when the molten metal is poured into the mould.
LIFTERS are used for removing loose sand from deep cavities in molds.
![Page 11: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/11.jpg)
TOOLS USED IN HAND MOLDING SPIRIT LEVEL is used
to check that the sand bed, moulding box or table of moulding machine is horizontal.
SPRUE CUTTERS used to cut openings in the sand mold for downsprues
![Page 12: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/12.jpg)
TOOLS USED IN HAND MOLDING GAGGERS are iron rods
bent at one or both ends. These are used to reinforce the moulding sand in the top portion of the moulding box and for supporting hanging sand
CHAPLETS are metal supports used to hold a core in place when core prints are inadequate.
![Page 13: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/13.jpg)
TOOLS USED IN HAND MOLDING SLICKS are used for
repairing and providing finishing to mold surface and edges after the pattern has been withdrawn. Heart and leaf slick,
Square and heart slick, spoon and bead slick, Heart and spoon slick, Leaf and spoon slick
![Page 14: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/14.jpg)
TOOLS USED IN HAND MOLDING GATE CUTTERS are
pieces of sheet brass bent to a semicircle on one edge. They are used to cut the in gate in the drag leading from the base of the sprue to the mold cavity.
![Page 15: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/15.jpg)
TOOLS USED IN HAND MOLDING RAPPING PLATE (OR) LIFTING PLATE is used to
facilitate shaking and lifting large pattern from the mold.
![Page 16: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/16.jpg)
RAMMING
![Page 17: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/17.jpg)
RAMMING Hand ramming is the method of packing sand
to produce sand mold.Uniform throughout the moldFirm enough to consolidate the sand,
but not hard enough to reduce the porosity which may prevent gases from escaping when the mold is poured.
Never strike the pattern forcibly because it may damage it or dislodge the pattern from its position.
![Page 18: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/18.jpg)
RAMMING Sprinkle some parting dust or graphite powder on
the pattern. Use the riddle to sift some molding sand over the
pattern until it is covered. Ram more sand in place over and around the
pattern, eventually filling the drag with rammed sand above the top edge.
![Page 19: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/19.jpg)
VENTING
![Page 20: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/20.jpg)
VENTING Venting is a process that is used to remove
trapped air from the closed mold and volatile gases from the processed molten material.
Concept: provide many pathways to allow trapped air and volatile gases to escape from the mold quickly and cleanly
![Page 21: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/21.jpg)
VENTING Pathways should
lead directly from the edge of the cavity image of the mold, to the outside atmosphere surrounding the mold
to be deep enough to let air and gases out easily, but not deep enough to allow the molten metal to escape through them.
![Page 22: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/22.jpg)
VENTING There are three major dimensions for the
vent. 1. “D”- Depth2. “W”-Width - 1/8 inch wide or more. 3. “L”- Length - minimum of 0.030 inch and a
maximum of 1/8 inch
![Page 23: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/23.jpg)
VENTING HOW MANY VENTS ARE NEEDED?
have at least 30% of the perimeter of the cavity image in vents, equally spaced around that perimeter
Vent the runner
![Page 24: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/24.jpg)
SPRUE MAKING
![Page 25: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/25.jpg)
SPRUE MAKING Sprue- the hole through which plastic or
metal is poured or cast into gate or reservoir and then into the mold.
![Page 26: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/26.jpg)
SPRUE MAKINGPlace a sprue pin in the sand adjacent to
the pattern and about one inch away from it.The location of sprue is not important to
symmetrical patterns because metal can be fed anywhere around the edge with equally good results
If pattern has some thin sections which are hard to fill completely, 2 or more sprues may actually be required
![Page 27: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/27.jpg)
RISER PUTTING
![Page 28: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/28.jpg)
RISER PUTTING Riser (Feeder Head)
A passage of sand made in the cope during ramming
Molten metal rises in the riser after mold cavity is filled up
The metal compensates for the shrinkage as the casting solidifies
Size depends on the freezing ratio
![Page 29: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/29.jpg)
RISER PUTTING Effective if:1. The riser cools after the casting, 2. The riser has enough material to
compensate for the casting shrinkage, and 3. the casting directionally solidifies towards
the riser.
![Page 30: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/30.jpg)
PUTTING POWDER IN THE PARTING LINE
![Page 31: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/31.jpg)
PUTTING POWDER IN THE PARTING LINE
A parting line, or seam in moldmaking is the place where two or more parts of the mold meet.
Parting Powder: is used to release cope from drag and over pattern preventing the molding sand from sticking and ruin the mould finishing.
(Talc, Graphite, Dry silica powder)
![Page 32: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/32.jpg)
Dust bag
![Page 33: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/33.jpg)
GATE MAKING
![Page 34: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/34.jpg)
GATE MAKING Gate - is a channel which connects runner
with the mould cavity and through which molten metal flows to fill the mould cavity. - should not have sharp edges - thin cross section
![Page 35: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/35.jpg)
GATE MAKINGThe Gating System
Minimize turbulent flow so absorption of gases, oxidation of metal and lessen the erosion of mould surfaces
Regulate entry of molten metalEnsure complete filling of mould cavityPromote temperature gradient within
casting so all sections could solidify properly
![Page 36: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/36.jpg)
GATE MAKING Pouring Basin: where the molten metal enters
the mold. Down Sprue: Path from the pouring basin, where
molten casting travels; Tapered Sprue Base: Where the casting's inner cavity
begins. Ingate/Choke Area: Runners: Are passages that distribute the liquid
metal to the different areas. Main Cavity: The impression of the actual part to
be cast is often referred to as the main cavity. Vents: Assist in the escape of gases Risers: Risers are reservoirs of molten material.
![Page 37: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/37.jpg)
![Page 38: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/38.jpg)
GATE MAKING GATE DESIGN RULES
Gate symmetrically to avoid warpage Gate into thicker sections for better filling
and packing Gate long, narrow parts from an end for
uniform flowMultiple gates shorten flow lengthsLocate gates on either side of a weak core
![Page 39: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/39.jpg)
CORES PLACEMENT
![Page 40: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/40.jpg)
CORES PLACEMENT Core
used in casting and molding processes to produce internal cavities and reentrant angles.
Normally a disposable item that is destroyed to get it out of the piece.
![Page 41: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/41.jpg)
CORES PLACEMENT Cores
Created from sand and a binder(resin) that cures through heat or gasification
Once prepared, they are set in place in the mold.
![Page 42: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/42.jpg)
CORES PLACEMENT Cores
1. Horizontal Core- used in horizontal position always at the paarting line between two mold boxes
2. Vertical Core- set in it’s vertical position.• Top and bottom ends are supported in the
seats formed by the core prints in molding sand
3. Balanced core- has one core to maintain alignment
1. - often used to produce blind cavity4. Drop core (Stop-off core)- used when cavity
either above or below the parting line
![Page 43: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/43.jpg)
CORES PLACEMENT5. Hanging core (cover core)- hangs vertically in the mold with no support at it’s bottom end
- mold cavity in the drag only
![Page 44: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/44.jpg)
SAFETY AND PRECAUTION
![Page 45: Hand Molding Demonstration Process](https://reader036.vdocuments.net/reader036/viewer/2022062502/56d6c0a71a28ab30169b4469/html5/thumbnails/45.jpg)
SAFETY AND PRECAUTUION Wear clothing suited for the job, wear shoes with thick
soles Do not play with the tools and equipment Always see that work and cutting tools on any machine
are clamped securely before starting. Keep the floor clean of metal chips or curls and waste
pieces, put them in container provided for such things. Put tools always when not in use Think about what you are doing at all times. Focus on
the job at hand and the next step. Have all moves planned and rehearsed prior to any operation.
Educate yourself beforehand and always be careful of your own and bystander safety