hazardous materials personal protective...
TRANSCRIPT
Hazardous Materials
Personal Protective Equipment Options
for the
Fort Thomas, Kentucky Fire Department
Jeffrey S. Parker
Managerial Issues in Hazardous Materials Professor Randy Hannifen
January 15 th , 2009
Hazmat PPE Options for FTFD 2
ABSTRACT
This research was conducted to comprehensively determine the personal protective equipment for
hazardous materials response appropriate for my department. The first consideration will need to be the basic
mission of my department. Secondly, our policies that carry out this mission and reflected by standard
operating guidelines would be reviewed. If there is a need to review and revise these policies, now is the time
to do it. All training, equipment, PPE, and expectations are based on these S.O.G.s. We need to develop these
S.O.G.s to the point where we are satisfied with them, then we may base all purchases on our expected
operations.
We must evaluate four factors. First, we need to determine the hostile environments we have the
probability and possibility to encounter. This will allow us to make some judgments applicable to our
jurisdiction, regarding capabilities and vulnerabilities. Our needs must be directed at the probabilities, and also
allow for possibilities. We need to determine what tasks will need to be performed. What is our local
department’s capability? Our operations must be guided by policy guided by frequency of use, capabilities,
training requirements, and efficiency. The tasks we perform will determine the protection needed.
INTRODUCTION
Mission Of The Department
The following is our mission statement:
“The mission of the Ft. Thomas Fire Department is dedicated in serving the citizens to prevent loss of life, personal injury, and property damage through emergency response, current departmental training, fire Prevention, and community education. The department will provide emergency medical services at the level of advanced life support towards the health, safety, and well-being of the patient/s. The department will provide optimal services in an efficient manor to the needs of our community and recognized by our community and our peers as leaders in the event of an emergency. The department will set examples of professionalism regardless of rank or position and actively participate in community events. The department will assist neighboring fire departments through mutual aid agreements to the extent that the City of Ft. Thomas is not left in harms way.” The mission says we will engage in emergency response to prevent loss of life, injury, and property
damage. It also says we will provide medical care at the level of advanced life support. It says we will provide
these optimal services in an efficient manner. It mentions participation in the mutual aid system. This tells us
Hazmat PPE Options for FTFD 3
that we need to determine what needs we have, how we can most efficiently meet these needs, and that this
may be with the assistance of an outside agency. Our needs are based on probability of incident type and the
possibility of incident severity. This would require a judgment or a calculated risk analysis.
Risk
The overall risk is divided into accidental risk and intentional risk. One could consider that our
accidental risk has not changed significantly since 9/11/01, and that our risk from intentional events has.
However, to some extent the vigilance to safety in the hazardous materials industry has increased do to
criminal threat considerations, and this has improved accidental safety to an undetermined degree. Our
criminal risk of a harmful incident was formally self-assessed in 2003.
Risk Assessment Needs Assessment
Shortfalls or “Gaps”
Desired Capabilities
Current Capabilities Vulnerability
Assessment Threat
Assessment
City of Fort Thomas, Ky.
This part of our risk was divided into vulnerabilities and threats. Our needs are based on this overall risk and
tells us where we need to be or “desired capabilities”. We measure where we are currently, and the difference
between current and desired capabilities represents our shortfalls. The shortfalls represent resources that
include PPE. The possibility of death, injury, or long term health hazards are all risks than need to be
lowered or eliminated.
Hazmat PPE Options for FTFD 4
These are methods to do this:
1 st choice- elimination of the risk,
2 nd choice- lowering of the frequency,
3 rd choice- elimination of the consequence, or
4 th choice - lowering of the consequencePriorities
We do not always have the financial resources to provide for all needs immediately and we must
prioritize. When looking at hazards, we may rate the problem per types of incidents. Then each type of
incident would have certain common hazards. These hazards could be predicted to some degree in fixed
facilities, but not in transportation incidents. This prevents us from relying on prediction of hazards to equip
ourselves. We must be prepared using an all hazard approach. However, we can control what personnel’s
roles would be. This determines the hazard level.
Probability of Occurrence Severity Factor Hazard Rating
Likely (3)
Possible (2)
Unlikely (1)
Not Possible (0)
High (3)
Average (2)
Low (1)
Probability X
Danger Chemical Spill or Leak ü ü 9 Highway ü ü 9 Rail ü ü 6 Earthquake ü ü 6 Conflagration ü ü 6 Tornado ü ü 6 Industrial Disaster ü ü 6 Terrorist Attack ü ü 6 Aircraft ü ü 4 Flood ü ü 4 Severe Storm ü ü 3 Nuclear Attack ü ü 3 Civil Disturbance ü ü 2 Marine ü ü 2 Volcano ü ü 0 Hurricane ü ü 0 Large Wildland Fire ü ü 0
Hazmat PPE Options for FTFD 5
Expected Probable Hazards
Our department is expected to perform on a “Hazardous Materials Operations Level”. This will not include
offensive operations. Offensive operations will be conducted by regional hazardous materials personnel.
NFPA 472 states that the operations level should be designated with competencies for various
responsibilities. There are core competencies and there are mission specific competencies. The core
competencies are analyzing the incident, planning the response, implementing the response, and evaluating
the response. Mission specific competencies include technical decontamination, mass decontamination,
product control, air monitoring and sampling, victim rescue and recovery operations, evidence preservation
and sampling, and response to illicit laboratory incidents. After we more clearly define the roles that our
department and that of the regional team play, we would be able to know the mission-specific competencies.
Presently, the core competencies of the operations level match the role our department plays. The mission-
specific competencies listed are performed by the regional team.
Fixed Facility Most Significant Hazards
Highest Level of FTFD PPE
Highest Level of Regional
HAZMAT PPE OPERATIONS LEVEL TECHNICIAN
LEVEL SPILL FIRE SPILL
NK Water Plant & Reservoir – Memorial Pkwy
Sodium Hypochlorite 12.5% Sodium Hydroxide Hydrofluosilic Acid Potassium Permanganate
Structural FF Gear W
ith SCBA
Level D
Level B Level C Level A Level C
NK Water Plant & Reservoir – Alexandria Pike
Sodium Hypochlorite Sodium Hydroxide Hydrofluosilic Acid Potassium Permanganate
Level B Level C Level A Level C
St Luke Hosp East – North Grand Ave. Liquid Oxygen
Radioactive Medical Materials
SPECIAL THERMAL Level C
Automobile Fuel Stations Gasoline Structural FF Gear With SCBA Structural FF Gear With SCBA Moore’s Home Center Propane
Possible Hazards
A review of our fixed facilities gives us a picture of our predictable hazards in these locations; however,
transportation hazards are nearly unpredictable.
Hazmat PPE Options for FTFD 6
Elements of a Personal Protection Program
Personal protection equipment can obviously prevent harm, but also cause harm to the user. This harm can
be caused by both incorrect use and malfunction of the equipment. Elements of a comprehensive program
should include:
1. Hazard Assessment - This has been elaborated on earlier. It includes a hazard assessment of chemicals
stored, transported, or used in the community.
2. Medical Monitoring of Personnel – The entirety of evaluation of personnel’s fitness for duty prior to
use, and medical monitoring during and after emergency incidents.
3. Equipment Selection – The is the focus of this report and considers the combination of:Environment
encountered
i. Toxicity
ii. Flammability
b. Personnel Objective
i. Offensive
ii. Defensive
c. Personnel that will use the equipment
4. Training – Must have an effective training program
5. Inspection – Equipment must be inspected at acceptance, at regular intervals prior to use while being
stored, and just after use if reusable.
6. Maintenance - Equipment must be maintained as applicable per the manufacturer’s guidelines.
7. Storage - Equipment must be stored per the manufacturer’s guidelines in order to prevent damage
and extend the useable life.
8. Respiratory Protection Program – This program should exist in fire departments as SCBA are
routinely in use. This includes:
Hazmat PPE Options for FTFD 7
a. Policy that address factors affecting the mask seal such as facial hair, eyeglass use, chewing
gum, or chewing tobacco.
b. Medication use in addition to overall fitness for duty evaluation.
Available Types of PPE
The EPA, OSHA, and the NFPA all have standards applicable to levels of personal protection.
Considering that each has a differing mission and role to play, and that they advocate for different
stakeholders, this should guide us on which we will use to follow in defining out personal protection. Two of
these are promulgate law, the Environmental Protection Agency, and the Occupational Safety and Health
Administration. The EPA is primarily concerned with protecting the environment, and OSHA is primarily
concerned with protecting the worker. However, these laws are defined by an administration of government
that may be effected to some degree by political considerations. However, the standards are law. The National
Fire Protection Association is a minimum standard written through a consensus derived from firefighters,
construction industry, manufacturers, and other groups. These standards are not law. Many thousands of
hazardous materials first responders are part of an association that advocates for safety. This association is
called the International Association of Fire Fighters. This organization has developed training and lists the
National Institute for Occupational Safety and Health as a source for its curriculum.
This curriculum meets OSHA and NFPA standards. NIOSH was created by the same law in 1970
that OSHA was created from. OSHA creates regulations and enforces them. NIOSH conducts scientific
research and makes recommendations for regulations. One can not assume that all recommendations are
followed. NIOSH would seem to be THE place for the most up to date and stringent information for
protection. The most specific protective information and protective material compatibility information comes
from the manufacturer. This would appear to be the “fox watching the hen house”. However, the financial
disincentive derived from legal liability from human injury and/or death drives these industries to thoroughly
study their product and disseminate information to the public. However, the material safety data sheet
Hazmat PPE Options for FTFD 8
(MSDS) sheet for a particular manufacturer does not always list protection as simply “level A”. For example
the MSDS for chlorine produced by BOC Gases, of Murray Hill, New Jersey specifies protection in this way:
The responder then needs to take this information and then match up a personal protective complement that
is sufficient.
Protection Levels
The following charts summarize the commonly referred to levels of personal protection. These charts show
uses, features, pros and cons, and relative costs.
EYE/FACE SKIN RESPIRATORY OTHER/GENERAL Gas-tight safety goggles or full-face respirator
PVC, Kel- F® or Teflon®
Positive pressure air line with full-face mask & escape bottle or self-contained breathing apparatus should be available for emergency
Safety shoes, safety shower, eyewash "fountain", face shield
TYPE PROTECTION LEVEL
Costs Protection PROS CONS USES Respiratory Skin Eye
LEVEL
A
Range from $1,000 to $4,000)
Highest level Highest level Highest level Best protection known at this time Can virtually eliminate possibility of contact with environmental hazards (provides its own environment)
Bulky Requires manpower to don and doff Physically stressful No cooling or heating Psychologically stressful (confinement) Work duration limited due to heat Reduced mobility, dexterity increases response time Communication may be difficult Will not survive fire conditions
Constant high concentration exposure (work activities such as plugging/patching) Skin absorbable chemicals Suspected or confirmed carcinogens EPA recommends Level A for entry into confined (closed) areas of unknowns
LEVEL
B
Ranges from $45 (non compliant) to $1,500
Highest level Lesser Level Highest level High level of respiratory protection Increased mobility/dexterity (theoretically) May be cooler Compliant garments have good penetration characteristics
Not gas/vapor tight not designed to protect from vapors/gases Not designed or tested (NFPA 1992) to be used at scenes involving carcinogens or skin absorbable chemicals Offers no thermal protection Can only be used in very controlled situations Offers no thermal protection
Probable exposure to low concentrations
Incidental Splash
Chemical is mainly a respiratory hazard
LEVEL
C
Inexpensive Lesser Level Lesser Level Optional Reduced respiratory stress (both physical and working time), because of APR use Tested against penetration and liquid integrity Light weight, less physical stress More comfortable Basically designed to be disposable (no reuse testing)
Can only be used in very controlled situations Greatly reduced flammability rating— no flash protection Reduced strength from typical Level B Requires oxygensufficient atmosphere Cannot be used in IDLH (Immediately Dangerous to Life and Health) environment Can only be used after a thorough site assessment
Reduced level of respiratory protection needed Well characterized and measured products Splashes or incidental contact with product will not cause harm to skin or be absorbed NFPA 1993 garments made for support zone activities, such as decontamination (in some cases), and remedial site mitigation.
LEVEL
D
Inexpensive No Protection No Protection Optional Allows for more efficient work activities in non emergency situations
Not for use in an emergency situation; typically worn only when moving product within a facility
Atmosphere contains no known hazard Work activities preclude splashes, immersion, or the potential for unexpected inhalation or contact with hazardous materials THERE IS NO EMERGENCY!
Hazmat PPE Options for FTFD 10
OSHA General Comment
Consists of: SCBA, Pos Press Supplied Air Resp W/ Escape SCBA
Fullface or halfmask, air purifying respirators
Escap e mask
Totally encapsulatin g chemical protective suit. Disposable protective suit, gloves and boots (depending on suit construction, may be worn over totally encapsulatin g suit)
Hooded chemical resistant clothing (overalls and longsleeved jacket; coveralls; one or two piece chemical splash suit; disposable chemical resistant overalls).
Hooded chemical resistant clothing (overalls; twopiece chemical splash suit; disposable chemical resistant overalls)
Coverall s & Hard Hat
Long underwea r
Gloves, outer, & inner chemical resistant Boots, chemical resistant, steel toe and shank
Boot covers, outer, chemical resistant, disposabl e
Safety glasses or chemical splash goggles
Face shield
LEVEL A
To be selected when the greatest level of skin, respiratory, and eye protection is required.
ü ü ü Option
ü Option
ü
LEVEL B
The highest level of respiratory protection is necessary but a lesser level of skin protection is needed
ü ü ü Option
ü ü Option
ü Option
LEVEL C
The concentration(s) and type(s) of airborne substance(s) are known and the criteria for using air purifying respirators are met.
ü ü Optio n
ü ü Option
ü ü Option
ü Option
LEVEL D
A work uniform affording minimal protection: used for nuisance contamination only
ü Optio n
ü ü Option
ü Option
ü ü Option
ü Option
ADDED CLOTHING
GLOVES BOOTS
RESP
Hazard has been identified. Requires highest level of protection for skin, eyes, and respiratory based on either the measured (or potential for) high concentration of vapors, gases, or particulates; or high potential for splash, immersion, or exposure to unexpected vapors, gases, or particulates that are harmful to or capable of being absorbed through the skin. High degree of hazard to skin are known or suspected, & skin contact is possible. Operations in confined, poorly ventilated areas & absence of conditions requiring Level A have not yet been determined.
Hazard requires high level of respiratory protection, but less skin protection. Less than 19.5 percent oxygen. Presence of incompletely identified vapors or gases is indicated by a directreading organic vapor detection instrument, but vapors & gases are not suspected of containing high levels of chemicals harmful to skin or capable of being absorbed through skin. This involves atmospheres with IDLH concentrations that present severe inhalation hazards & that do not represent a severe skin hazard; or that do not meet the criteria for use of airpurifying respirators.
The atmospheric contaminants, liquid splashes, or other direct contact will not adversely affect or be absorbed through any exposed skin; The types of air contaminants have been identified, concentrations measured, and an airpurifying respirator is available that can remove the contaminants; and All criteria for the use of airpurifying respirators are met.
No known hazard & no potential for splash, immersion, or unexpected inhalation of or contact with hazardous levels of any chemicals.
SUITS EYE / FACE
The following is a summary of available personal protective equipment (PPE) that is available:
LEVEL A - Du Pont Responder® Suit $787.95
Level A - Single taped seams, Standard face shield(PVC 40 mil), Internal adjustment belt, Gas tight zipper
closure, Double storm flap, Two exhaust valves, Expanded back, Replaceable butyl gloves, Attached sock boots,
Outer boot flaps
LEVEL B -
Tychem™ SL $122.95
Encapsulated suit - is a lightweight fabric that provides effective and economical Level B protection against
a broad range of chemicals. Encapsulated suit is roomy enough to accommodate turnouts and SCBA being
worn underneath. The encapsulated suit has a rear entry design with expanded back and 48” zipper.
Encapsulated suit has a strong heat-sealed storm flap with Velcro, 20 mil PVC face shield, elastic wrists, 2
exhaust ports with shrouds and attached sock boots with boot flaps.
Tychem® F Coverall $47.95
Represents a remarkable step forward in the provision of individual protection for both Armed Forces and
Civilian Populations in areas where chemical and/or biological warfare could take place, or where there is a
risk of contamination from an industrial accident. Tychem® F coveralls provides a tough and safe barrier to
many chemical warfare agents in a liquid, gas or aerosol formats and represents the first simple, economic
and disposable material for individual protection suits.
Level C
Response Suit $62.00
Coverall with attached hood and inner cuff. Heavy duty PVC on high count nylon
polyester-.35mm thickness. Meets Federal Apparel Flammability Act FDS 5903.1.
Reinforced knees, elbows and crotch area to prevent splitting. Heavy duty elastic
Hazmat PPE Options for FTFD 13
adjustable suspender with deluxe suspender clip. Adjustable waist snaps for the perfect fit. Clear I.D. badge
pocket on chest
Level D
Response Suit $8.65
Coveralls combine microporous film laminate with a polypropylene non-woven substrate for improved
protection plus comfort. Provides excellent barrier for improved splash and dry particulate protection — ideal
for paint spraying, liquid handling, sand blasting, hazardous fiber and dust handling. Biologically inert, low-
linting and treated to minimize static buildup. Serged seam construction with zipper front. Elastic wrists and
ankles. Attached hood and boots. Soft, inner polypropylene fabric absorbs moisture-helps reduce heat stress
and increase productivity. Economical, disposable and completely incinerable
Terrorism
There are effective guidelines that are useful from several sources. One such source is NFPA 1994. Another basic guide for all hazardous materials responses including possible or known terrorist incidents for initial guidelines is the US DOT Emergency Response Guidebook.
CHEMICAL BIOLOGICAL TERRORISM NFPA 1994
SINGLE EXPOSURE GARMENTS
CHALLENGE SKIN CONTACT
VAPOR THREAT
LIQUID THREAT VICTIM’S CONDITION
CLASS 1 Vapors
Aerosols Pathogens
Not Permitted
Unknown or Not Verified
High Unconscious
Not Symptomatic Not Ambulatory
CLASS 2
Limited Vapors Liquid Splash
Aerosols Pathogens
Not Probable IDLH Moderate Mostly Alive, but Not
Ambulatory
CLASS 3 Liquid Drops Pahogens
Not Likely TLV STEL Low to None Self-Ambulatory
Hazmat PPE Options for FTFD 14
CONCLUSIONS
In analyzing my department’s jurisdiction, resources, past and future frequency and type of response,
the department needs to retain an operations level for an awareness and defensive posture, with increased
support of a regional entity that will be capable and available for offensive maneuvers at the technician level.
After working thoroughly sorting out the appropriate roles that our local department and the hazardous
materials team plays, the appropriate PPE can be recommended.
o The department of (19) members and shift staffing of maximum of (6) and a minimum of (4) needs to
purchase and maintain;
• The latest in SCBA respiratory protection;
• Structural Firefighting gear
• (12) sets of protective suits classified as Level D
• (6) sets of protective suits classified as Level B
These may be used as appropriate in defensive situations or decontamination operations that
allow this level of protection.
o The regional hazardous materials response team needs a full complement for the number of
responders plus backup of;
• SCBAs
• Supplied Air Respiratory Equipment
• Escape Air Capability
• Level A suits
• Level B suits