INFINEON FLASHER – UNLOCKER HELP

1.Phone connecting

- Start software- In “Ports & Settings” window check “Enumerate Ports” and select port on which box

is. Select baudrate on which you want to communicate with phone-higher baudrate means higher working operations speed. Possible baudrates are 115200,230400,460800 and 921600 bd.

- In “Models & Cable” window select your needed model.- Check if this phone model supports USB mode:

- Select your needed connection mode – STANDART connection for working via box and RJ45 cable or USB connection for working with USB cable, connected to PC directly

- In “Models & Cable” window near phone model look what cable is needed- If you selected STANDART connection-connect powered OFF phone to box via RJ45

cable, press- “CONNECT PORT” and “CONNECT PHONE” , press phone’s POWER ON shortly and

wait until phone will connects and phone info will be read.- If you selected USB connection-select anyone existing port or same port where box

is, press “CONNECT PORT” and “CONNECT PHONE” and connect phone to USB cable-phone must be without battery

- Wait until phone info will be read

WARNING! For working in USB mode – phone USB drivers must be installed. All possible drivers can be found at automatic supports sites in “LG”-“LG software”-“Software”-“Software for SmartCard dongle”-“LGQ-AMOI-ZTE drivers” folder. For Infineon phones – “ LG_Infineon_USBDriver” must be installed.For Infineon_AGR phones (GB220,GB230,GU220,GU230) – “LG_Infineon_AGR” drivers must be installed.For OMAP based phones (KM700,GD330) use “LG_OMAP_USBDriver”.WARNING! Some older “Infineon_USBDriver” versions not allow correct Infineon_AGR drivers installing.In this case do next :- go to your Programs Files folder – standart is C:\Programs Files- find and open in it “infineon” subfolder - open “Infineon USB driver” subfolder in “infineon” folder- run unistaller “unins000.exe”

After this download from supports new “LG_Infineon_USBDriver” and “LG_Infineon_AGR” driversand repeat drivers installation.

USB cable which goes together with phone or anyone LG USB cable with KG800connector can be used. LG Qualcomm models USB cables can be used also.

Service functions like “READ IMEI”, “WRITE IMEI” and “RESET PHONE” are not supported in USB CONNECTION mode – if you want to use it – you need to select “STANDART CONNECTION” and use RJ45 cable.

Some phone versions in USB mode not allow to use all possible functions, and for such versions after connecting software can show next message:

- If you get such message, it means , that such phone you can only flash in USB mode, if you want other functions like “DIRECT UNLOCK”, “READ SIM UNLOCK CODE” ,“WRITE BACKUP”, “REPAIR EEPROM” or “READ FLASH” - you need to use STANDART CONNECTION mode

- If you want only to flash phone, press “OK”, later press “DISCONNECT PHONE” and disconnect phone from USB cable, after press “CONNECT PHONE” and connect phone to USB cable again

- Wait until phone will connects, go to “FLASHER” section and select flash file (BIN, CRB and FLS

- Flashes are allowed) and flash phone

WARNING! All other functions in this LIMITED MODE not works

UNLOCKER SECTION

1.”DIRECT UNLOCK” FUNCTION

- This function is for phone’s direct unlocking. When software makes DIRECT UNLOCK in most cases it creates SP zone backup and places it in “LG” – “Backups” folder. Backup file looks like for example “LG-KP500_357920024455667_bkp.crf”.Backup files are not overwritten-if software will create next backup file ,it will look like “LG-KP500_357920024455667_01_bkp.crf”, “LG-KP500_357920024455667_02_bkp.crf” and etc.

- Backup file can be used to restore phone to previous state using “WRITE BACKUP” function.

2.”WRITE BACKUP” FUNCTION- This function is used to write to phone before read backup file. Press “WRITE

BACKUP” – select your needed backup file and it will be written to phone.

3.”READ SIM UNLOCK CODE” FUNCTION- This function is to read phone SIM UNLOCK CODE

4.”REPAIR EEPROM” FUNCTION- Use this function to repair blinking, freezing phones-

4a.“REPAIR SERVICE NA” function is used for KM310f from Telcel unlocking-you need to use it after phone flashing with not locked flash,when phone writes “Service not available”.

5.SERVICE FUNCTIONS – “READ IMEI”, ”WRITE IMEI” and “RESET PHONE”- To use these functions phone must be connected in different way. For connecting

phone must be ON and without SIM card.- Connect RJ45 cable to phone and press “CONNECT PORT” at software, don’t press

“CONNECT PHONE” :

- For IMEI reading press “READ IMEI” and wait until software will read IMEI – if it can’t do this, try few times to press “C” on phone while IMEI reading goes.

- To write IMEI – check “FIX IMEI” and to IMEI window enter your needed IMEI – after this press “WRITE IMEI”. Some phones for IMEI changing need “DIRECT UNLOCK” or “ENABLE WRITE IMEI” functions. Anyway software by self will inform you – these functions are needed or not.

-- For phone resetting – phone code clearing and etc. – use “PHONE RESET” function.

FLASHER SECTION

1.”ADD FILES” FUNCTION

- This function is for selected flash files adding to “FLASHER” window. In Open File dialog window select your needed flash files and they will be added to “FLASHER” window .Function supports multi selecting – you at once can select few files – simply keep pressed “CTRL” on PC keyboard when selecting needed flash files.

- In additional way flashes can be added by drag and drop – simply drag and drop flash file on “FLASHER” window.

2.”REMOVE FILES” FUNCTION

- This function is to remove flash files from “FLASHER” window.

3.”WRITE FILES & DO JOBS” FUNCTION

- This function is for selected flash files writing.

WARNING! FLASHER supports not only encrypted CRC, CRF and CRB files writing, but also and LG factory flashes with extensions BIN, CAB, FLS, CUST, EEP and DFFS writing. If factory flash consists of few files like files with .cust, .fls and .dffs extensions – they all must be opened at once :

READER SECTION

1.”READ FLASH” FUNCTION

- This function is for flash file reading. Select what you need to read and press “Read flash” for this.

ABOUT & SUPPORT SECTION

1.”ENTER SUPPORT SITE”

- This function is for support site entering. Select one or other support site and press “ENTER SUPPORT SITE” button to enter to it :