high bond structural adhesive epoxy material safety …

of 5

Bluey Technologies Pty LtdABN 36 115 613 646

PO Box 898, HamiltonQLD 4007 AustraliaTel: + 61 7 3135 9440Fax: + 61 7 3161 7918

Material Safety Data Sheet

BluRez EpiMax 575 CompoundHIGH BOND STRUCTURAL ADHESIVE EPOXY


1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

1/630 Darling Street, Rozelle, NSW, AUSTRALIA, 2039(02) 9818 1844

AddressTelephone

EmergencyEmail

(02) 9818 1844Fax (02) 9818 1866

[email protected]://www.bluey.com.auWeb Site

Supplier Name BLUEY TECHNOLOGIES

BLUREZ EPIMAX 575 (COMPOUND)PRODUCT NAME

TWO COMPONENT HIGH BOND STRUCTURAL ADHESIVE EPOXYUse(s)Synonym(s) 957 - PRODUCT CODE • STRUCTURAL ADHESIVE • BLUREZ 575 • EPIMAX 575

MSDS Date 18 December 2007

CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA2. HAZARDS IDENTIFICATION

RISK PHRASESR36/38 Irritating to eyes and skin.R41 Risk of serious damage to eyes.R43 May cause sensitisation by skin contact.R51/53 Toxic to aquatic organisms, may cause long term adverse effects in the aquatic environment.SAFETY PHRASESS24/25 Avoid contact with skin and eyes.S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.S45 In case of accident or if you feel unwell seek medical advice immediately (show the label where possible).

NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODENone Allocated None Allocated None AllocatedNone Allocated None Allocated None Allocated

UN No.Pkg Group

DG ClassHazchem Code

Subsidiary Risk(s)EPG

3. COMPOSITION / INFORMATION ON INGREDIENTSIngredient Formula CAS No. ContentEPOXY RESIN (C15-H16-O2.C3-H5-Cl-O)x 25068-38-6 30-60%ADDITIVES Not Available Not Available remainder

Eye If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing until advised tostop by the PIC or a doctor, or for at least 15 minutes.

Skin Remove contaminated clothing and gently flush affected areas with water. Seek medical attention if irritationdevelops. Launder clothing before reuse.

Inhalation Leave area of exposure immediately. If other than minor symptoms occur, seek immediate medical attention. Ifassisting a victim avoid becoming a casualty, wear a Type A (Organic vapour) respirator. If victim is not breathingapply artificial respiration.

Ingestion DO NOT induce vomiting. Immediately wash out mouth with water, and then give water to drink. Seek medical

4. FIRST AID MEASURES

Page 1 of 4

Reviewed: 18 Dec 2007Printed: 18 Dec 2007

RMT

attention.

Advice to Doctor Treat symptomatically.Australia & [email protected]

PO Box 898, Hamilton QLD 4007 Australia

+61 (0)7 3135 9440

+61 (0)7 3161 7918

+61 (0)7 3135 9440

PRODUCT NAME BLUREZ EPIMAX 575 (COMPOUND)

Fire andExplosion

Non flammable. Evacuate area and contact emergency services. Remain upwind and notify those downwind ofhazard. Wear full protective equipment including Self Contained Breathing Apparatus (SCBA) when combatingfire. Use waterfog to cool intact containers and nearby storage areas.

Extinguishing Non flammable. Prevent contamination of drains or waterways, absorb runoff with sand or similar.

Flammability Non flammable. May evolve toxic gases (carbon oxides, hydrocarbons) when heated to decomposition.

Hazchem Code None Allocated.

5. FIRE FIGHTING MEASURES

Spillage If spilt (bulk), contact emergency services where appropriate. Wear splash-proof goggles, nitrile/viton gloves, aType A (Organic vapour) respirator (or Full-face Air-line respirator in confined areas), coveralls and rubber boots.Ventilate and clear area of all unprotected personnel. Absorb spill with sand or similar, collect and place insealable containers for disposal.

Handling

Store in cool, dry, well ventilated area, removed from oxidising agents, acids, alkalis, direct sunlight, heat orignition sources, foodstuffs, out of direct sunlight and out of the reach of children. Ensure containers areadequately labelled, protected from physical damage and sealed when not in use. Check regularly for leaks orspills. Large storage areas should have appropriate fire protection.

Storage

Before use carefully read the product label. Use of safe work practices are recommended to avoid eye or skincontact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating,drinking and smoking in contaminated areas.

6. ACCIDENTAL RELEASE MEASURES

7. STORAGE AND HANDLING

8. EXPOSURE CONTROLS / PERSONAL PROTECTIONExposure Stds No exposure standard(s) allocated.

No biological limit allocated.Biological Limits

EngineeringControls

Do not inhale vapours. Use in well ventilated areas. In poorly ventilated areas, mechanical extraction ventilation isrecommended.

PPE Wear splash-proof goggles, a Type A (Organic vapour) Respirator, nitrile or viton (R) gloves and coveralls. Ifsanding dry product, wear a Class P1 (Particulate) Respirator. If spraying, with prolonged use, or if in confinedareas, wear impervious coveralls and an Air-line respirator.

9. PHYSICAL AND CHEMICAL PROPERTIESAppearance COLOURED PASTE Solubility (water) INSOLUBLE

Odour SLIGHT ODOUR Specific Gravity 1.5 to 1.7

pH NOT AVAILABLE % Volatiles NOT AVAILABLE

Vapour Pressure NOT AVAILABLE Flammability NON FLAMMABLE

Vapour Density NOT AVAILABLE Flash Point NOT RELEVANT

Boiling Point NOT AVAILABLE Upper Explosion Limit NOT RELEVANT

Melting Point NOT AVAILABLE Lower Explosion Limit NOT RELEVANT

Evaporation Rate NOT AVAILABLE Autoignition Temperature NOT AVAILABLE

of 4


RMT


1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

1/630 Darling Street, Rozelle, NSW, AUSTRALIA, 2039(02) 9818 1844

AddressTelephone

EmergencyEmail

(02) 9818 1844Fax (02) 9818 1866

[email protected]://www.bluey.com.auWeb Site

Supplier Name BLUEY TECHNOLOGIES

BLUREZ EPIMAX 575 (COMPOUND)PRODUCT NAME

TWO COMPONENT HIGH BOND STRUCTURAL ADHESIVE EPOXYUse(s)Synonym(s) 957 - PRODUCT CODE • STRUCTURAL ADHESIVE • BLUREZ 575 • EPIMAX 575

MSDS Date 18 December 2007

CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA2. HAZARDS IDENTIFICATION

RISK PHRASESR36/38 Irritating to eyes and skin.R41 Risk of serious damage to eyes.R43 May cause sensitisation by skin contact.R51/53 Toxic to aquatic organisms, may cause long term adverse effects in the aquatic environment.SAFETY PHRASESS24/25 Avoid contact with skin and eyes.S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.S45 In case of accident or if you feel unwell seek medical advice immediately (show the label where possible).

NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODENone Allocated None Allocated None AllocatedNone Allocated None Allocated None Allocated

UN No.Pkg Group



3. COMPOSITION / INFORMATION ON INGREDIENTSIngredient Formula CAS No. ContentEPOXY RESIN (C15-H16-O2.C3-H5-Cl-O)x 25068-38-6 30-60%ADDITIVES Not Available Not Available remainder

Eye If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing until advised tostop by the PIC or a doctor, or for at least 15 minutes.

Skin Remove contaminated clothing and gently flush affected areas with water. Seek medical attention if irritationdevelops. Launder clothing before reuse.

Inhalation Leave area of exposure immediately. If other than minor symptoms occur, seek immediate medical attention. Ifassisting a victim avoid becoming a casualty, wear a Type A (Organic vapour) respirator. If victim is not breathingapply artificial respiration.

Ingestion DO NOT induce vomiting. Immediately wash out mouth with water, and then give water to drink. Seek medical

4. FIRST AID MEASURES

Page 1 of 4


RMT

attention.

Advice to Doctor Treat symptomatically.

Page 2 of 5



of 5



Fire andExplosion

Non flammable. Evacuate area and contact emergency services. Remain upwind and notify those downwind ofhazard. Wear full protective equipment including Self Contained Breathing Apparatus (SCBA) when combatingfire. Use waterfog to cool intact containers and nearby storage areas.

Extinguishing Non flammable. Prevent contamination of drains or waterways, absorb runoff with sand or similar.

Flammability Non flammable. May evolve toxic gases (carbon oxides, hydrocarbons) when heated to decomposition.

Hazchem Code None Allocated.

5. FIRE FIGHTING MEASURES

Spillage If spilt (bulk), contact emergency services where appropriate. Wear splash-proof goggles, nitrile/viton gloves, aType A (Organic vapour) respirator (or Full-face Air-line respirator in confined areas), coveralls and rubber boots.Ventilate and clear area of all unprotected personnel. Absorb spill with sand or similar, collect and place insealable containers for disposal.

Handling

Store in cool, dry, well ventilated area, removed from oxidising agents, acids, alkalis, direct sunlight, heat orignition sources, foodstuffs, out of direct sunlight and out of the reach of children. Ensure containers areadequately labelled, protected from physical damage and sealed when not in use. Check regularly for leaks orspills. Large storage areas should have appropriate fire protection.

Storage

Before use carefully read the product label. Use of safe work practices are recommended to avoid eye or skincontact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating,drinking and smoking in contaminated areas.

6. ACCIDENTAL RELEASE MEASURES

7. STORAGE AND HANDLING

8. EXPOSURE CONTROLS / PERSONAL PROTECTIONExposure Stds No exposure standard(s) allocated.

No biological limit allocated.Biological Limits

EngineeringControls

Do not inhale vapours. Use in well ventilated areas. In poorly ventilated areas, mechanical extraction ventilation isrecommended.

PPE Wear splash-proof goggles, a Type A (Organic vapour) Respirator, nitrile or viton (R) gloves and coveralls. Ifsanding dry product, wear a Class P1 (Particulate) Respirator. If spraying, with prolonged use, or if in confinedareas, wear impervious coveralls and an Air-line respirator.

9. PHYSICAL AND CHEMICAL PROPERTIESAppearance COLOURED PASTE Solubility (water) INSOLUBLE

Odour SLIGHT ODOUR Specific Gravity 1.5 to 1.7

pH NOT AVAILABLE % Volatiles NOT AVAILABLE

Vapour Pressure NOT AVAILABLE Flammability NON FLAMMABLE

Vapour Density NOT AVAILABLE Flash Point NOT RELEVANT

Boiling Point NOT AVAILABLE Upper Explosion Limit NOT RELEVANT

Melting Point NOT AVAILABLE Lower Explosion Limit NOT RELEVANT

Evaporation Rate NOT AVAILABLE Autoignition Temperature NOT AVAILABLE

Page 2 of 4


RMT


Chemical Stability Stable under recommended conditions of storage.Conditions toAvoid

Avoid heat, sparks, open flames and other ignition sources.

10. STABILITY AND REACTIVITY

Material to Avoid Incompatible with oxidising agents (eg. hypochlorites, peroxides), acids (eg. sulphuric acid), alkalis (eg.hydroxides), heat and ignition sources.

Decomposition May evolve toxic gases (carbon oxides, hydrocarbons) when heated to decomposition.HazardousReactions

Hazardous polymerization is not expected to occur.

Health HazardSummary

Irritant - low to moderate toxicity. Use safe work practices to avoid eye or skin contact and vapour inhalationduring the curing process. Skin sensitisation may result from exposure. Skin sensitisation is by far the mostcommon effect of epoxy resin exposure in industry. Due to product form (paste), the potential for an inhalationhazard is reduced. The cured resin is considered non toxic.

Eye Irritant. Exposure may result in lacrimation, irritation, pain and redness.Inhalation Irritant. Over exposure to resin whilst curing may result in mucous membrane irritation of the nose and throat,

coughing, possible sensitisation with asthma-like symptoms and pulmonary oedema at high levels.Skin Irritant. Contact may result in irritation, skin rash and dermatitis. Sensitisation is also common with exposure to

epoxy resins.Ingestion Low toxicity. Ingestion may result in headache, nausea, vomiting, gastrointestinal irritation and diarrhoea.Toxicity Data EPOXY RESIN (25068-38-6)

LD50 (Ingestion): 2 - 19 g/kg (rat) LD50 (Skin): > 20 mL/kg (rabbit)

11. TOXICOLOGICAL INFORMATION

Environment Limited ecotoxicity data was available for this product at the time this report was prepared. Ensure appropriatemeasures are taken to prevent this product from entering the environment.

12. ECOLOGICAL INFORMATION

Waste Disposal Mix parts A + B together (small amounts), absorb with sand, vermiculite or similar and dispose of to an approvedlandfill site. Ensure protective equipment is worn when mixing. Do not seal containers/tins until reaction iscomplete. Contact the manufacturer for additional information. Prevent contamination of drains or waterways asenvironmental damage may result.

Legislation Dispose of in accordance with relevant local legislation.

13. DISPOSAL CONSIDERATIONS

14. TRANSPORT INFORMATIONNOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE

None Allocated None Allocated None AllocatedNone Allocated None Allocated None Allocated

Shipping NameUN No.Pkg Group



None Allocated

Poison Schedule Classified as a Schedule 5 (S5) Poison using the criteria in the Standard for the Uniform Scheduling of Drugs andPoisons (SUSDP).

AICS All chemicals listed on the Australian Inventory of Chemical Substances (AICS).

15. REGULATORY INFORMATION

AdditionalInformation

This product is used in conjunction with BluRez EpiMax 575 (Hardener).

WELDING - SANDING - CUTTING DRIED OR CURED PRODUCT: If sanding, cutting or welding dried or cured

16. OTHER INFORMATION

Page 3 of 4


RMT



Chemical Stability Stable under recommended conditions of storage.Conditions toAvoid

Avoid heat, sparks, open flames and other ignition sources.

10. STABILITY AND REACTIVITY

Material to Avoid Incompatible with oxidising agents (eg. hypochlorites, peroxides), acids (eg. sulphuric acid), alkalis (eg.hydroxides), heat and ignition sources.

Decomposition May evolve toxic gases (carbon oxides, hydrocarbons) when heated to decomposition.HazardousReactions

Hazardous polymerization is not expected to occur.

Health HazardSummary

Irritant - low to moderate toxicity. Use safe work practices to avoid eye or skin contact and vapour inhalationduring the curing process. Skin sensitisation may result from exposure. Skin sensitisation is by far the mostcommon effect of epoxy resin exposure in industry. Due to product form (paste), the potential for an inhalationhazard is reduced. The cured resin is considered non toxic.

Eye Irritant. Exposure may result in lacrimation, irritation, pain and redness.Inhalation Irritant. Over exposure to resin whilst curing may result in mucous membrane irritation of the nose and throat,

coughing, possible sensitisation with asthma-like symptoms and pulmonary oedema at high levels.Skin Irritant. Contact may result in irritation, skin rash and dermatitis. Sensitisation is also common with exposure to

epoxy resins.Ingestion Low toxicity. Ingestion may result in headache, nausea, vomiting, gastrointestinal irritation and diarrhoea.Toxicity Data EPOXY RESIN (25068-38-6)

LD50 (Ingestion): 2 - 19 g/kg (rat) LD50 (Skin): > 20 mL/kg (rabbit)

11. TOXICOLOGICAL INFORMATION

Environment Limited ecotoxicity data was available for this product at the time this report was prepared. Ensure appropriatemeasures are taken to prevent this product from entering the environment.

12. ECOLOGICAL INFORMATION

Waste Disposal Mix parts A + B together (small amounts), absorb with sand, vermiculite or similar and dispose of to an approvedlandfill site. Ensure protective equipment is worn when mixing. Do not seal containers/tins until reaction iscomplete. Contact the manufacturer for additional information. Prevent contamination of drains or waterways asenvironmental damage may result.

Legislation Dispose of in accordance with relevant local legislation.

13. DISPOSAL CONSIDERATIONS

14. TRANSPORT INFORMATIONNOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE

None Allocated None Allocated None AllocatedNone Allocated None Allocated None Allocated

Shipping NameUN No.Pkg Group



None Allocated

Poison Schedule Classified as a Schedule 5 (S5) Poison using the criteria in the Standard for the Uniform Scheduling of Drugs andPoisons (SUSDP).

AICS All chemicals listed on the Australian Inventory of Chemical Substances (AICS).

15. REGULATORY INFORMATION

AdditionalInformation

This product is used in conjunction with BluRez EpiMax 575 (Hardener).

WELDING - SANDING - CUTTING DRIED OR CURED PRODUCT: If sanding, cutting or welding dried or cured

16. OTHER INFORMATION

Page 3 of 4


RMT


product, adverse health effects may be avoided by the use of appropriate engineering controls and/or personalprotective equipment. If welding, wear a Class P2 (Metal fume) respirator and depending on the nature of thesurface being welded, additional protection (eg. for organic vapours/acid gas) may also be required. A Class P1(Particulate) respirator is recommended if dust is generated.

EPOXY - PHENOXY RESINS AND POLYURETHANES: Where spray painting with two or more component epoxyresins or polyurethane paints is undertaken, an employee shall wear a air-line respirator, full length chemicallyresistant coveralls and gloves. Further, if an individual is to enter an enclosed booth where a vapour or gas curingprocess is occurring, an air-line respirator is required. Once cured, these resins are considered non toxic.

RESPIRATORS: In general the use of respirators should be limited and engineering controls employed to avoidexposure. If respiratory equipment must be worn ensure correct respirator selection and training is undertaken.Remember that some respirators may be extremely uncomfortable when used for long periods. The use of airpowered or air supplied respirators should be considered where prolonged or repeated use is necessary.

ABBREVIATIONS:ADB - Air-Dry Basis.BEI - Biological Exposure Indice(s).CAS# - Chemical Abstract Service number - used to uniquely identify chemical compounds.CNS - Central Nervous System.IARC - International Agency for Research on Cancer.M - moles per litre, a unit of concentration.mg/m3 - Milligrams per cubic metre.NOS - Not Otherwise Specified.pH - relates to hydrogen ion concentration using a scale of 0 (high acidic) to 14 (highly alkaline).ppm - Parts Per Million.TWA/ES - Time Weighted Average or Exposure Standard.

HEALTH EFFECTS FROM EXPOSURE:It should be noted that the effects from exposure to this product will depend on several factors including: frequencyand duration of use; quantity used; effectiveness of control measures; protective equipment used and method ofapplication. Given that it is impractical to prepare a Chem Alert report which would encompass all possiblescenarios, it is anticipated that users will assess the risks and apply control methods where appropriate.

PERSONAL PROTECTIVE EQUIPMENT GUIDELINES:The recommendation for protective equipment contained within this Chem Alert report is provided as a guide only.Factors such as method of application, working environment, quantity used, product concentration and theavailability of engineering controls should be considered before final selection of personal protective equipment ismade.

Report Status This document has been compiled by RMT on behalf of the manufacturer of the product and serves as themanufacturer's Material Safety Data Sheet ('MSDS').

It is based on information concerning the product which has been provided to RMT by the manufacturer orobtained from third party sources and is believed to represent the current state of knowledge as to the appropriatesafety and handling precautions for the product at the time of issue. Further clarification regarding any aspect ofthe product should be obtained directly from the manufacturer.

While RMT has taken all due care to include accurate and up-to-date information in this MSDS, it does not provideany warranty as to accuracy or completeness. As far as lawfully possible, RMT accepts no liability for any loss,injury or damage (including consequential loss) which may be suffered or incurred by any person as aconsequence of their reliance on the information contained in this MSDS.

of 4


RMT

Prepared By Risk Management Technologies5 Ventnor Ave, West PerthWestern Australia 6005Phone: +61 8 9322 1711Fax: +61 8 9322 1794Email: [email protected]: www.rmt.com.au

End of Report18 December 2007MSDS Date:

Page 4 of 5




product, adverse health effects may be avoided by the use of appropriate engineering controls and/or personalprotective equipment. If welding, wear a Class P2 (Metal fume) respirator and depending on the nature of thesurface being welded, additional protection (eg. for organic vapours/acid gas) may also be required. A Class P1(Particulate) respirator is recommended if dust is generated.

EPOXY - PHENOXY RESINS AND POLYURETHANES: Where spray painting with two or more component epoxyresins or polyurethane paints is undertaken, an employee shall wear a air-line respirator, full length chemicallyresistant coveralls and gloves. Further, if an individual is to enter an enclosed booth where a vapour or gas curingprocess is occurring, an air-line respirator is required. Once cured, these resins are considered non toxic.

RESPIRATORS: In general the use of respirators should be limited and engineering controls employed to avoidexposure. If respiratory equipment must be worn ensure correct respirator selection and training is undertaken.Remember that some respirators may be extremely uncomfortable when used for long periods. The use of airpowered or air supplied respirators should be considered where prolonged or repeated use is necessary.

ABBREVIATIONS:ADB - Air-Dry Basis.BEI - Biological Exposure Indice(s).CAS# - Chemical Abstract Service number - used to uniquely identify chemical compounds.CNS - Central Nervous System.IARC - International Agency for Research on Cancer.M - moles per litre, a unit of concentration.mg/m3 - Milligrams per cubic metre.NOS - Not Otherwise Specified.pH - relates to hydrogen ion concentration using a scale of 0 (high acidic) to 14 (highly alkaline).ppm - Parts Per Million.TWA/ES - Time Weighted Average or Exposure Standard.

HEALTH EFFECTS FROM EXPOSURE:It should be noted that the effects from exposure to this product will depend on several factors including: frequencyand duration of use; quantity used; effectiveness of control measures; protective equipment used and method ofapplication. Given that it is impractical to prepare a Chem Alert report which would encompass all possiblescenarios, it is anticipated that users will assess the risks and apply control methods where appropriate.

PERSONAL PROTECTIVE EQUIPMENT GUIDELINES:The recommendation for protective equipment contained within this Chem Alert report is provided as a guide only.Factors such as method of application, working environment, quantity used, product concentration and theavailability of engineering controls should be considered before final selection of personal protective equipment ismade.

Report Status This document has been compiled by RMT on behalf of the manufacturer of the product and serves as themanufacturer's Material Safety Data Sheet ('MSDS').

It is based on information concerning the product which has been provided to RMT by the manufacturer orobtained from third party sources and is believed to represent the current state of knowledge as to the appropriatesafety and handling precautions for the product at the time of issue. Further clarification regarding any aspect ofthe product should be obtained directly from the manufacturer.

While RMT has taken all due care to include accurate and up-to-date information in this MSDS, it does not provideany warranty as to accuracy or completeness. As far as lawfully possible, RMT accepts no liability for any loss,injury or damage (including consequential loss) which may be suffered or incurred by any person as aconsequence of their reliance on the information contained in this MSDS.

Page 4 of 4


RMT

Prepared By Risk Management Technologies5 Ventnor Ave, West PerthWestern Australia 6005Phone: +61 8 9322 1711Fax: +61 8 9322 1794Email: [email protected]: www.rmt.com.au

End of Report18 December 2007MSDS Date:

of 5



high bond structural adhesive epoxy material safety …

Documents