Construction and remodeling projects are not

easy, but with the proper tools and know-how,

your next project can be a breeze.

Carpet protection dispensers are an important tool to help prepare the

jobsite and protect its flooring assets. While not required, dispensers

easily cut the installation time in half when compared to manual

installation by hand. They’re also quick to assemble and simple to use.

HERE ARE A FEW REASONS YOU MAY NEED A CARPET PROTECTION DISPENSER:

The surface area you need to protect is very large

You need to get the job done quickly

You experience back, knee, hip, or other joint problems from strained manual labor

You expect to use the dispenser frequently or on multiple projects

The first step is to determine the size you need for your rolls of film protection.

The dispenser pictured below fits 24”, 30”, and 36” rolls. There are also larger

dispensers available with 36”, 48”, and 60” rolls.

The dispenser comes with three

different poles to correspond with

the different sizes of film rolls.

SIZING

The main piece of the dispenser has three holes: 24”, 30”, and 36”.

ASSEMBLY

STEPS

STEP 1

1 2

SLIDE THE END PIECE INTO THE MAIN PIECE

Take the end piece and slide it into the

main piece by pushing the pin down.

When you reach the correctly sized hole

for your film roll, release the pin to lock

the pieces in place.

1

REPEAT WITH THE OTHER END PIECE ON THE OPPOSITE SIDE

Take the other end piece and slide it into the

main piece on the opposite side by pushing

the pin down. Note: Do not adjust to the exact size

of the roll until the roll is in place.

Leave room to attach the roll in the

next few steps.

STEP 2

!

1

ATTACH ONE END OF THE POLE

Attach one end of the pole in between the end

pieces by placing the pole end over the wheel.

STEP 3

1 2

PUT THE FILM ROLL INTO PLACE

Stand the dispenser up on one end so it is vertical.

This will make it easier to add the film roll.

Next, put the film roll into place opposite

the pole.

STEP 4

Remember: Make sure the sticky side of the film is up and the edge is pointing the way you want to go.!

LOCK THE POLE AND FILM ROLL INTO PLACESTEP 5

1 2

Push the pin in to release the end piece and slide

it down to the appropriate size. Position the pole

and film roll over the wheels and push into place.

Reattach the end piece by snapping the pin into

the hole. This will secure the pole, film roll, and

main pieces of the device into place.

1

ATTACH THE HANDLE TO THE DISPENSER

Attach the handle to the center of the dispenser.

CONGRATULATIONS! YOU’VE JUST ASSEMBLED YOUR CARPET PROTECTION DISPENSER.

NEXT WE’LL TAKE A QUICK LOOK AT HOW TO USE THE DISPENSER AND GET ROLLING!

STEP 6

HOW TO USE THE CARPET PROTECTION DISPENSER

STEP 1

1 2

GET THE FILM ROLL STARTED

Pull the film out and back over the pole. Position the dispenser so the film is beneath

the roller, sticky side down.

1

ROLL THE FILM

Move the dispenser forward by pushing the

handle to roll out the film.

STEP 2

1

CUT THE FILM

When you are finished with one section, you

can use the metal pole roller as a base to make

a straight, even cut.

You are then free to reposition the dispenser to

continue applying the film to the next section.

STEP 3

REPEAT AS NECESSARY

Continue the process until you have

applied protection to the entire

area needed.

STEP 4

CONCLUSION

JUST REMEMBER TO FOLLOW THESE QUICK AND EASY STEPS:

TO ASSEMBLE

Slide the end piece into the main piece

Repeat with the other end piece on the opposite side

Attach one end of the pole

Put the film roll into place

Lock the pole and film roll into place

Attach the handle to the dispenser

JUST REMEMBER TO FOLLOW THESE QUICK AND EASY STEPS:

TO USE

Get the film roll started

Roll the film

Cut the film

Repeat as necessary

If you have any questions about assembling or using

your carpet protection dispenser, contact the experts

at Pro Tect today! No one knows how to “pro tect”

your floors better than Pro Tect.

THANKS