General Rules for Removing Old Finish

1. Do nothing that will harm the original surface unless the piece is to be painted.

2. If you plan to replace the old finish with a clear type, all old finish must be removed so the new will hold properly.

3. When removing old paint it is not only permissible but acceptable to most collectors that the marks of wear

through the years, as well as traces of color from the old paint be allowed to remain so that they will show through the new finish. Traces of old paint add interest to the piece

by their variations of color, and are evidence of age. Old paint however, should not be left on in thick patches or

blotches.

4. For final cleaning, after using a remover, use a cabinet scraper or knife blade on joints, corners, and angles on flat

surfaces. Use steel wool to clean out carvings, turnings, mouldings etc.

5. If the old finish is shellac, you don't need a paint and varnish remover. It can be taken off with denatured

alcohol and steel wool.

Selecting Your Paint Remover

Commercial removers are solvents rather than corrosives. They act more slowly on older paints than on new, but

they are the only materials that can be used safely. They attack the material such as linseed oils used in paint, or

the resins in shellac, varnish, and lacquer. It won't injure a surface by burning it or leaving marks and won't be harmful to glue or raise the grain of the wood. They

contain no water and may be used on veneered surfaces without causing the veneer to loosen. When used properly

and washed off, solvent-type paint removers leave the surface clean. Dislodging layers of old paint or varnish isn't difficult, but patience, time, and-following the directions

on the container are required.

How to Remove Old Finishes

Dislodging layers of old paint or varnish isn't difficult, but it takes patience, time, ans perseverance. Here are some

basic directions for using paint remover.

1. Place the piece to be worked on over layers of old newspaper in good strong light, and if possible, with the

top surface in a horizontal position. Avoid working in cold temperatures below 68 degrees F--cold slows down the

action of removers.

2. Shake the remover thoroughly, pour a small amount into a small can and apply thickly with a full brush in one

direction. Do not rebrush.

3. Let the remover stand for a period of from 10 to 20 minutes, or until the paint or varnish lifts.This is indicated by a crinkling of the surface. Do not let the remover dry. If it begins to dry, apply an additional coat and wait for it to

act.

4. When the surface covering has lifted, remove it with a dull putty knife that has the corners rounded off. Remove

the accumulation of remover and finish and wipe the knife on a piece of old newspaper.

5. Wipe off as much of the remaining finish as possible using burlap squares.

6. Scrub the surface with a small brush dipped in denatured alcohol.

7. Wipe off with several clean cloths.

8. Rub the surface with steel wool dipped in denatured alcohol.

9. Wipe with cloths dipped in alcohol. This not only cleans the traces of remover from the surface but neutralizes its further action. Follow by wiping with clean cloths dipped

in turpentine or paint thinner.Then wipe with dry rags. This will remove any remaining wax or silicone polish that may have been used on the finish in the past. 10. Allow to

dry thoroughly for at least 24 hours.

Removing Deeply Buried Paints

A deeply buried paint can be removed entirely or partially by a simple procedure. This is paint usually left after you have removed the previous cotes with remover or light

scraping. Because it's so simple it's worth trying.

1. Apply a liberal coat of shellac with a brush and let it dry for at least 24 hours. 2. Use the remover as previously

directed. All or part of the buried paint will come off with the shellac. Be sure all traces of the remover is gone and

the surface is completely dry before applying a new finish.

http://www.cottonwoodcovecrafts.com/