hrm 2007a
TRANSCRIPT
Introducing the CON-E-CO HRM-12
Horizontal / Reversing Central Mix Drum
How Does The Horizontal Mixer Fit Into Today’s Ready Mix Market
FEATURES• No Hydraulic System
• No Open Gearing
• Reduced Concrete Splatter
• Quiet Operation
• Variable Discharge Rate
BENEFITS• Less Maintenance
• Eliminates Gear Lube• Less Maintenance• Environmental Friendly
• Cleaner Operation • Less Maintenance
• Reduces Sound Level Inside Building
• Optimizes Mixer Fleet Truck Charging
• Eliminates Excessive Wear on Tilt Pins
How Does The Horizontal Mixer Fit Into Today’s Ready Mix Market
• Non-Tilting Operation
• Sealed Mixing Drum
• Requires Less Overhead Clearance
• Reduced Building Cost
• Less C.F.M. Required • Smaller Less Expensive Dust
control System
Solutions to Problems Inherent to Horizontal
Mixers
DRUM DRIVE TIRES
FEATURES• High Traction Drive System
• Tire Grooves
BENEFITS• Eliminates Tire Slippage with
Low Slump and Larger Mixing Capacities
• Eliminates Blistering Tire Heat Build Up
High Traction Drive Tires
ELECTRICAL
Features• Climate Controlled Service
Panel
• Isolated Resistor Bank
Benefits• Cools Variable Speed
Frequency Drive to Promote Long Trouble Free Operation
• Eliminates Motor Generated 58,000 Watt Back Feed to Variable Speed Frequency Drive for Trouble Free Operation
Variable Frequency Drive System
ELECTRICAL
FEATURES• Drive Motors wired to
Individual Disconnects
BENEFITS• Allows Isolation of Each Motor
for Troubleshooting• Less Expensive Field Wiring
Required
Individual Motor Disconnects
ELECTRICAL
FEATURES• Single Phase 220 Volt
Emergency Drives
BENEFITS• Operated with Small
Generator or Portable Welder
Emergency Drives
BOLT IN PADDLES
FEATURES• Factory Jig Fixture
Manufactured Bolt In Paddles
BENEFITS• Simple Bolt In Replacement• Less Down Time
Mixing Paddle Mountings - Spider
BOLT IN PADDLES
FEATURES• Enclosed Bolted Assembly
Dual Element Paddles Support Spider
BENEFITS• Less Concrete Build Up• Less Maintenance
Mixing Paddle Mountings - Spider
BOLT IN PADDLES
FEATURES• Steel Reinforced 1” Urethane
Liner on Mixing Side of Belly Blades
BENEFITS• Prevents Concrete Build Up
Between Liner and Paddle Face
• Less Maintenance
Mixing Paddle Mountings – Belly
INLET CHUTE
FEATURES• Bolt In Ceramic Tiled 1”
Urethane Lined Inlet Charging Chute
BENEFITS• Long Life • Less Maintenance
Replaceable “Bolt-in” Chute Liners
INLET CHUTE
FEATURES• Urethane Inlet Seal
BENEFITS• Spillage Free • No Maintenance
Interchangeable Mixer Part – Inlet Seal
INLET CHUTE
FEATURES• 36” Retractable Inlet Chute
BENEFITS• Allows Easier Maintenance
Access Into Drum
Mixer Charging Hood & Water Lines
INLET CHUTE
FEATURES• Isolated Temper Water Inlet
Pipe
BENEFITS• Allows Water to be Injected
Into Center of Mixing Action for Faster Slumping Action
Temper Water Pipe
DRUM CONSTRUCTION
FEATURES• ¾” Steel Drum
BENEFITS• Sturdy Long Life Construction
Drum Construction
DRUM CONSTRUCTION
FEATURES• 1” Urethane Drum Liner
Attached on 6” Spacing on Perimeter and 9” spacing in Center Area
BENEFITS• Prevents Concrete Build Up
Between Liner and Drum • Less Maintenance• Longer Liner Life
Drum Urethane Attachment
FACTORY DRIVE ALIGNMENT
FEATURES• Precise Factory Drive
Alignment
BENEFITS• Critical to Proper Operation
Drive Shaft Alignment
FIELD DRIVE ALIGNMENT
FEATURES• Factory Built In Precision
Drive Realignment
BENEFITS• Allows Simple Field
Realignment After Drive Maintenance
• Less Down Time
Drive Shaft Realignment