© 2013 Chapman/Leonard Studio Equipment, Inc.

HybridTM

IV Camera DollyUSER GUIDE

Operational Instructions & Specifications

HybridTM IV

The Operator should be Qualified. For Assistance Please call our 24 hour Customer Service at 1-888-883-6559.© 2001 No part of this manual may be reproduced or electronically transmitted without

the written permission of Chapman/Leonard Studio Equipment, Inc.Revision - 05/2014

Ohio15919 Industrial Parkway

Cleveland, OH 44135

Toll Free: 888-758-4826 216-241-4800

Fax: 216-241-4805

Customer Service at 888-883-6559 or 818-764-6726.

Chapman / Leonard Certified Locations:

Louisiana668 Distributors Row Suite E

Elmwood Business ParkNew Orleans, LA 70123

Toll Free: 888-758-4826504-731-6050

Fax: 504-731-6051

Florida

Orlando, Florida 32837

Toll Free: 888-337-8243 407-851-3456

Fax: 407-855-1653

New York38-75 11th Street

Toll Free: 888-758-4826

Fax: 718-389-1899

Texas1901 E. 51st Street

Toll Free: 888-758-4826 512-473-0084

Fax: 512-473-0042

MAIN OFFICE12950 Raymer Street,

North Hollywood, CA 91605

www.chapman-leonard.comToll Free: 888-883-6559

818-764-6726Fax: 818-764-6730 Rentals

818-764-4347 Leasing818-764-9391 Accounting

UK and EuropeChapman Leonard Studio

Equipment, Ltd.Unit 2

North Orbital Commercial Park Napsbury Lane, St. Albans, Herts

www.chapmanleonard.com+44 1 727 838424

Fax: +44 1 727 852241

New Mexico5650 University Blvd. SEAlbuquerque, NM 87106

Toll Free: 888-758-4826

Fax: 505-227-2578

Georgia120 Parkwest Drive #D

Toll Free: 888-758-4826

Fax: 678-583-1858

The Operator should be Qualified. For Assistance Please call our 24 hour Customer Service at 1-888-883-6559.© 2001 No part of this manual may be reproduced or electronically transmitted without

the written permission of Chapman/Leonard Studio Equipment, Inc.Revision - 05/2014

CONTENTS1 Specifications

3 Geometry Lever

4 Arm Markers

9 Fast Mode

10 Detent Bypass

10 Float Mode

13 Brakes

19 Upper and Lower Board Setup Modes

24 Accessories

1. Conventional Mode2. Crab Mode

3. Round Mode

Steering modes

The Universal Stop Valve controls arm movement with smooth, feathered stops. Adjustments to the Universal Stop Valve can be made without tools or the need to remove any covers or access plates.

The Hybrid IV has a new Valve Control Float

A new tire design

The Side Board System

The Hybrid IV has a built-in heat control system in the hydraulic system to maintain a minimum hydraulic oil tempera-ture of 70ºF. This maintains optimum performance in even the coldest environment.

HybridTM IV Specifications

The Hybrid IV in Low Profile Mode with

Vertical Boom Travel 43 in./1.09 m

(Low Plate Setup)

(Low Plate Setup)

HYBRIDTM IVCamera Dolly

Stripped Down Carrying Weight = 395 lbs. (180 kg)Maximum Payload with Strut Attached = 700 lbs. (317.5 kg)

880mm Track Configuration(Legs are set at 80 degrees)

CHAPMAN

880mmTrack

Standard Track Configuration(Legs are set at 12 degrees)

241/2 inchTrack

Low Profile Extension

CHAPMAN

64.2”

4.4”

HY

BR

ID IV

21.4”

CHAPMAN

53”

17”19”

14”

HY

BR

ID IV

0˚

12.9˚45˚

90˚

180˚

90˚45˚

12.9˚

0˚

Standard Track

Standard Track

12˚ Standard Track

80˚ 880mmTrack

37”

39”

Top View of Leg Configurations

Compact & Narrow Track Configuration(Legs are set at 0 degrees)

With 7 in.Extension

With 7 in.Extension

2113/16 inchTrack

29.5”27”

62”

47.2”

HybridTM IV Geometry Lever

Setup Leg Positions Geometry Lever CommentsStandard EURO Track 80º

Standard Track 12.9º º 241/2 TrackNarrow Profile 0º º

Compact Profile 180º

0º

168º 1/2 Track 12º 1/2 Track

º

0º or 180º

in all situations.

The lever has three positions. Before the Geometry Lever is moved, the transmission must first be shifted

0º or 12º positions, the Geometry Lever must be moved to the left toward the center line of the Dolly (Inboard).

A sticker is mounted near the Geometry Lever as a reminder.

Wall Hugger Configuration

The Asymmetrical

placement close to a wall or

a more stable platform for the Operator.

Tip: Use the QuickJack to help make quick leg changes

HybridTM IV Arm Markers

Colored Velcro Markers attach to the Arm (Upper and Lower). They can be repositioned to different locations on the Arm

Precise, repetitive Stops are possible at all speeds. An improved Stop Valve System allows even faster, smoother stops.

adjustment that can be performed in the field by a qualified technician.

MarkerIndicator

MarkersLined Up

HybridTM

Conventional Mode the rear wheels pivot as the operator Crab Mode all wheels turn in uni-

Round

Handles. Control Pins can be set to limit which modes can

can make transitions with confidence.

Never use pliers or channel locks on any part of the Dolly.

1. Shift fully to clear the

(Halfway between Crab/ Conv. or Crab/Round.)

2. shift into Round, Crab or Conventional Modes.

If the transmission still

NOTE

Locked Position

FREE SHIFTING BETWEEN ALL SELECTIONSBOTH PINS OUT

SHIFTING BETWEEN CRAB & CONVENTIONAL ONLYTOP PIN OUT BOTTOM PIN IN

SHIFTING BETWEEN CRAB & ROUND ONLYTOP PIN IN BOTTOM PIN OUT

LOCKED IN CRAB ONLYBOTH PINS IN

2

1

”

”

Crab Steering Mode

HybridTM

The Hybrid IV can beshifted smoothly into either Round

the course of a shot, even while

with confidence.

is a new feature of theHybrid IV.

The Dolly can now be turned completely within

it an ideal choice for

is the selection used most

any direction. The camera lensmaintains its orientation to the

Conventional Steering Mode

Round Steering Mode

MinimumTurn Radius

20 inches

MinimumTurn Radius

31 inches

feels loose. Then turn the bottom collar until it can be removed.

1

Hybrid Series of Dollies.

2

Column.

3 4

5

screw and collar. Test the dolly by

76

Make sure that the wheels are all oriented

HybridTM

HybridTM

The Universal Stop Valve

The UP Feathering Lever

The DOWN Feathering Lever -

Control Valve Handle removed for clarity.When making Stop Adjustments:1. Be certain the Arm is well beyond the desired Stop point. Then turn the Lever in beyond the desired Stop point.2. Open the Main Control Valve to approach the desired Stop.3. Open Lever to achieve movement until the desired Stop point is reached.4. Close the Main Control Valve.

For rapid deceleration beyond the normal for this system, the Dolly Grip can use the Stop Valve to initiate the Stop, then finalize the Stop with the Main Control Valve.

DOWN UP

More Travel

Less Travel

Push Turn

Turn

DOWNLess Travel

More Travel

Push

TurnTurn

UP

WARNING!

Failure to place the Control Valve in the Neutral position may cause the arm

HybridTM IV Fast Mode

push the arm down when the control value is opened. The Fast Mode Value is located on the rear left side of the

NOTE

WARNING!

HybridTM IV Detent Bypass

NOTE: the Arm is now reverse direction without hesitation. Therefore, the Float position is achieved. Additionally the Grip can select their own Detent as preferred for a smoother transition from an upward or downward direction.

New to the Hybrid IV dolly is the ability to eliminate the detent feature of the Control

the Detent feature. There are only two

HybridTM IV Float Mode

A new feature of the Hybrid IV dolly is the ability to fine tune how the arm reacts to the Control Valve Handle. The

The Detent Bypass is ON when the button is pushed IN. It is OFF when the button is pulled out.

HybridTM

The Valve Control Handle doubles as

into the Foot Pump.

HybridTM

Do not attempt maintenance on the

Start Button

For Optimal Safety

Electrical Ground

HybridTM IV Brakes-

incline.

HybridTM

clearance of 5/16 inch can be adjusted down to zero. In the Adjustable Detent Control System this can be felt as the

Off position is between the Detents.

qualified technician.

Valve Control Handle

Foot Pump

The default position

HybridTM

Flipped1 2

3 4

Remove Quick Release Pin

Replace Quick Release Pin andTighten Nut

Foot Rest

Other Leveling Head Options

The same Set Up as shown above, but

Head in the Normal Up position

BACK POSITIONThe payload on

can be increased to 700 lbs. if the Support Strut is in place.

FRONT POSITION

For PayLoadOver 350 lbs

BACK POSITION

HybridTM

Head into place.

Cam Lever Button on the side. The Head will now rotate

Payload.

HybridTM

The Narrow Side Boards attach to either side of the Hybrid IV. They slide into place and are secured to the chassis with two thumb screws. As shown in this picture.

Low Mode Setup. The Standard Side Boards attach to either side of the Hybrid IV onto the Narrow Side Boards

are secured to the chassis with two thumb screws.

connects to the Standard Side Board.

The Standard Side Boards are also adjustable for and aft on the

the board to the desired location.

Position lock down knob.

Hybrid TM

The Side Boards may be moved to the rear of the Dolly for easy access to the front thumb screw. Then move

the board forward to access the rear thumb screw.

The Adjustable Front Board attaches with

Board in either the Upper or Lower position.

HybridTM

A latch is located on the Chassis to hold the Adjustable Front Board or the Lift Pins in place.

2

-

43

1

HybridTM IV Upper and Lower Board Setup Modes

attached to the Hybrid IV, a stable platform allows the Grip to move the Dolly with a Camera Operator

on board.

Full Lower Side Board Setup

HybridTM

Full Side Board Set Up (Upper or Lower)

Standard Side Board Set Up

Narrow Side Board Set Up

Boards are only used in the Upper Position.

1R

6

1L

6

4

4

22

5R 5L3

4

7R 7L

22 1R 1L

3

7L

7R

HybridTM IV Accessories

Narrow Side Board (Left)

Front Board (Adjustable)

Narrow Corner Board (Left)

Dolly Seat w/Collar

Front Lift/Push BarsRear Lift/Push Bars

Seat OffsetDolly Nose Seat

Head w/Nose L Plate

Low Camera Plate

Accessory Cart CoverHybrid IV User Guide

Location11211112

111111 11221111111111

1

11111

M RM RU L&RUUM FM FM F M FM FM AU AU FM A M LM LBBBM RM RM RBBM AM LM LM A M A BBBBB

Number1L1R2345L5R6 7L7R

Left Rear (Aft)

6

HybridTM

U Upper

M Middle

B

L Left Side

R

F Front

A Aft (Rear)

LEGEND

1R

1L

Nose Seat

Left Side

HybridTM

improve performance on Floors, Hardwood, Track and

behind tire squeaks and the tendency of tires to stick to

Use the same spray to clean the tires.

FOR USE WITH ALL CHAPMAN DOLLIES

the lower rear Side Board Hole.

the lower center Side Board Hole.

the center Side Board Hole.

Easily lifts the Hustler dolly

Easily lifts the Hybrid dolly

Easily lifts the PeeWee dolly for a

to a different side board hole.

HybridTM TM IV

For Metal

Never directly spray the Dolly with water. Use soap and water applied to a cloth or paper towel, or preferably a brush to wipe down the rubber and metal parts of the Dolly.

the finish. A clean Dolly will ensure optimum performance with

Performance on Tile Floors, Hardwood, Track and even on Concrete. Use the same spray to clean the Tires.

For Rubber and Plastic

HybridTM IV Optional Accessories

The optional Rainhouse protects the camera and operator from the elements.

Also available in an opaque sunshade version.

Rear Deck Board

Grip Pouch

HybridTM

Use all four

make a move with

Bar per end or per side may cause injury.

Bars from the Accessory Cart to remove the Dolly

are fully seated and the

of the Hybrid IV is 395 lbs.

Remove the Lifting Bars from the dolly and place them in the crate. Accessories that come off the Hybrid

IV to be placed in or on the Accessory Cart.

The dolly is cradled and no additional bolts or straps are needed.

One side of the Accessory Cart Crate can be lowered to form a ramp. The Accessory Cart can then be wheeled

HybridTM

Dolly must be properly crated before shipment.

If no bays are available, please park on Raymer Street and advise the Rental Office of your arrival.

Our Rental Staff is well trained to process equipment and documents efficiently

*ALL RENTALS must be returned by 10:00 AM at the North Hollywood Facility.

12950 Raymer StreetNorth Hollywood, CA 91605

n

Rental Office Hours:Monday - Friday: 7:00 AM – 6:00 PMSaturday: 8:00 AM – 12:00 PMSundays: CLOSED

210

118

405

SHERMAN WAY

RAYMER ST.

COLD

WAT

ER C

YN.

170

134

101

118

N