hydraulic cylinders - breedveld-weaver.nl · [strong type] under no load condition: 1000 mm/s max....

11cat-No.78E since2017

Hydraulic Cylinders

How to Select Hydraulic Cylinders and Handling Precautions

･･･････････ 12

Single-Acting Cylinders ･･･････････ 13 to 24Double-Acting Cylinders ･･･････････ 25 to 33Special Cylinders ･･･････････ 34 to 47Cylinder Parts ･･･････････ 48 to 53Data ･･･････････ 54 to 56

www.breedveld-weaver.nl

12

CylindersH

ydraulic Cylinders

Single-Acting CylindersDouble-Acting Cylinders

Special C

ylindersC

ylinder partsD

ata

cat-No.78E since2017

How to Select Hydraulic Cylinders and Handling Precautions

External and internal drawings are available for all models.

● While the cylinder is operating, the output must be 70 to 80 % of the maximum output specified in the specifi-cations.

How to determine the output 1

● Upon request, 5000 kN or larger cylinders and even those that are not listed in the catalogue can be manu-factured. Please contact us for further information.

Special cylinders8

● The contents of this catalogue are subject to change without notice.

Please visit our website for the latest information.

http://www.rikenkiki.co.jp

Other 10

● Use a VC-70 quick coupler that eliminates loosening if a coupler is frequently removed or is subject to vibra-tion (see page 170).

● If the impact pressure is high (e.g. punchings), do not use S-1, S-2, and ROC couplers.

● Securely and completely connect the couplers.Do not connect or separate the couplers while pressure is applied.

● If pressure is likely to be applied to the inside of the cylinder due to the ambient temperature, use the pres-sure elimination accessory to remove pressure before connection.

Attached couplers9

● Select a cylinder whose stroke is longer than that to be required.

How to determine the stroke2

● Riken products must be used at an ambient tempera-ture of 0 to 40 °C. In the case of cylinders that need a low volume of oil, the internal pressure may increase depending on the ambient temperature. In this case, a quick coupler or a one-touch coupler may not be able to be connected.

● During operation, the hydraulic oil temperature must be within 5 to 60 °C.

● Riken products are designed for indoor use (except some products).

Operating environment6

● If a cylinder that works normally with self-sealing cou-plers (S-1R, S-24R, S-5R) stops suddenly, the most likely cause is looseness (a gap) between the couplers.

Tighten the couplers again using a tool if a gap exists.

Handling Precautions7

● Avoid using the whole stroke of the cylinder. (Avoid abutting by using the whole stroke.)

● A strong cylinder (see pages 34 to 36) is recommend-ed if the cylinder is frequently used. Please contact us for further information.

● Cylinders are classified into the single-acting type (load-return, spring-return) and the double-acting type (hydraulic-return) according to the return function.

● Load-return types have no return function. An external force is required to return the piston.

How to determine the cylinder type: single-acting or double-acting3

If attaching a heavy jig or the like to the piston, select a pump with a falling-by-self-weight prevention valve. Other-wise, there is a danger of sliding of the piston at a speed which the pump cannot handle or caused by the weight of the jig, etc. when the pump does not work.

When using cylinder parts such as caps, be sure to screw them completely. When they are not screwed completely and also used frequently, the thread may be damaged, and accordingly they may be broken off or not be able to be removed. If the orientations of cylinder parts such as a cylinder base and clevis need to be aligned, please let us know your request.

The cylinder speed must be within the follow-ing speed specifications. Otherwise, the equip-ment may be damaged or scattered matter may cause injury.[Standard type] Under no load condition: 500 mm/s max. At 70 Mpa: 30 mm/s max.[Strong type] Under no load condition: 1000 mm/s max. At 70 Mpa: 50 mm/s max.

● If the pump is used with an electric pump , select a pump suitable for the application referring to the cylin-der speed table (on page 226).

How to determine the cylinder speed 4

● The cylinder should be loaded vertically. ● The allowable eccentric load is within 2.5 % of the load

specified in the specifications. ● The collar thread must be generally used to secure the

cylinder with a flange or the like (see page 49). ● The cap should always be used when the load is

received directly by the piston. In addition, use cylinder parts (see pages 48 to 53) according to the application.

How to determine the mounting and securing methods5

● The return spring of a single-acting cylinder generates force to return the piston only. In addition, the return time varies depending on the hose length, etc.

● Select a double-acting type if the cylinder is frequently used or if pull output is required when a heavy jig is attached to the piston.

40 kN cylinder100 kN cylinder200 kN cylinder300 kN cylinder500 kN cylinder

1000 kN cylinder

Return force

Approx. 0.07 kNApprox. 0.15 kN Approx. 0.35 kN Approx. 0.45 kN Approx. 0.75 kN Approx. 1.50 kN

………………………………………………………………

Gap


13

Single-acting cylinders (spring-return type)


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■LJ3-15VC

■LJ5-15VC/LJ7.5-15VC/LJ10-15VC

■LJ1-15VC/LJ2-15VC/LJ3-15VC

■LJ15-15VC/LJ20-15VC

■SpecificationsModel LJ1-15 LJ2-15 LJ3-15 LJ5-15 LJ7.5-15 LJ10-15 LJ15-15 LJ20-15

Maximum output kN 100 200 300 500 750 1000 1500 2000

Effective area cm2 14.52 30.19 46.56 72.38 109.35 149.57 215.12 285.26

Minimum overall length A 44 52 58 65 76 83 99 112

Cylinder internal diameter ϕ 43 62 77 96 118 138 165.5 190.6

Cylinder external diameter ϕ C 70 88 105 132 154 174 214 262

Piston diameter ϕ D 34 48 60 82 105 112 140 165

Piston protrusion length H 1

Width across flats R 60 78 98 — — — — —

Coupler protrusion length

VC-70-R3

S

≈ 46

S-1R ≈ 53

ROC-13R ≈ 49

Coupler position T 17 18 19 21 25 28 27 28

Required oil volume cm3 22 46 70 109 164 225 323 428

Approx. weight kg 1.1 2.1 3.5 6.4 10.5 14.2 26.2 45.0

Maximum operating pressure 70 MPaMaximum output 100 to 2000 kNStroke 15 mmCylinder system Single-acting Return system Spring-returnCoupler connection port size Rc3/8

100 to 2000 kN (LJ Series)

Model code structure

LJ 1 - 15 VCStroke Attached coupler

Maximum output (mm) VC : VC-70-R31 : 100kN S : S-1R2 : 200kN T : ROC-13R3 : 300kN -NC : W/O coupler5 : 500kN

7.5 : 750kN10 : 1000kN15 : 1500kN20 : 2000kN

Single-acting cylinderLJ series

For cylinder and pump selections, see page 54.

● Thin jack with 15 mm stroke for all models.● 500 kN and larger jacks have a handle. ● The cylinder tube and piston stop ring are plated with electroless

nickel.


14

Single-acting cylinders (spring-return type) H

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■MC05-25VC/50VC ■MC1-15VC/25VC/35VC ■MC2-25VC/50VC

■MC1-50VC ■MC2-50VC

■SpecificationsModel MC05-25 MC05-50 MC1-15 MC1-25 MC1-35 MC1-50 MC2-25 MC2-50

Maximum output kN 50 100 200

Effective area cm2 7.16 14.52 28.74

Stroke mm 25 50 15 25 35 50 25 50


Cylinder internal diameter ϕ 30.2 43 60.5

Cylinder external diameter ϕ C 46 57 82

Piston diameter ϕ D 18 28 37 38

Head cover diameter ϕ F 20 27 45 36

Piston protrusion length H 11 11 19 16

Piston hole diameter ϕ J 8 19 — 19

Piston hole length K 25 30 — 35

Collar thread size M M45 x 1.5 M58 x 2 M82 x 2

Collar thread length N 23 25 50

Incomplete thread length R 3 6 6


VC-70-R3

S

≈ 46 ≈ 46 ≈ 46

S-1R ≈ 53 ≈ 53 ≈ 53

ROC-13R ≈ 49 ≈ 49 ≈ 49

Coupler position T 25 21 25 25

Boss length U 18 17 19


Approx. weight kg 1.2 1.7 1.6 1.9 2.2 2.1 4.3 5.6

■Compatible attachments Attachment location Cylinder parts MC05-25 MC05-50 MC1-15 MC1-25 MC1-35 MC1-50 MC2-25 MC2-50

Piston Tilt saddle — R-1020SP — R-1020SP

Collar thread Flange 5FM 10FM 20FM

● The piston and the inside of the cylinder tube are plated.● A special head cover is included.● Short type having a minimized overall length.

Maximum operating pressure 70 MPaMaximum output 50/100/200 kNCylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8

50 to 200 kN (MC Series)


MC 05 - 25 VCSingle-acting cylinder Attached coupler

MC series Stroke VC : VC-70-R3Maximum output (mm) S : S-1R

05 : 50kN T : ROC-13R1 : 100kN -NC : W/O coupler2 : 200kN



15



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■S04-40VC ■S04-15VC

■S04-50VC ■S04-70VC ■S04-127VC/S04-150VC

■S04-15VC

●The piston and the inside of the cylinder tube are plated.

Maximum operating pressure 70 MPaMaximum output 40 kNCylinder internal diameter ϕ 28.6Effective area 6.42 cm2

Cylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8

■SpecificationsModel S04-15 S04-40 S04-50 S04-70 S04-127 S04-150

Stroke mm 15 40 50 70 127 150Minimum overall length A 46 126 148 190 252 288Cylinder external diameter ϕ C 40 40 39Piston diameter ϕ D 25 17 25Piston thread size E — 3/4-14NPTPiston thread length G — 24Piston protrusion length H — 11 29Collar thread size M — 1 1/2-16NSCollar thread length N — 27 28Base thread size P — 3/4-14NPTIncomplete thread length R — 2 3


VC-70-R3S

≈ 46 ≈ 40S-1R ≈ 53 ≈ 47ROC-13R ≈ 49 ≈ 43

Coupler position T 18 20 20 35 40Required oil volume cm3 10 26 33 45 82 97Approx. weight kg 0.7 1.2 1.1 1.4 1.9 2.1

■Compatible attachmentsAttachment location Cylinder parts S04-15 S04-40 S04-50 S04-70 S04-127 S04-150

PistonPiston thread

Cap — With special head cover R-4PPiston base — RB-4

Clevis — CLF-4-A (B)Collar thread Flange — 4FS

Base threadCylinder base — CB-4

Clevis — CLM-4-A (B)

40 kN (S Series)


S 04 - 15 VCMaximum output Attached coupler

04 : 40 kN VC : VC-70-R3S : S-1RT : ROC-13R

Single-acting cylinder -NC : W/O couplerS series Stroke (mm)



16


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■MS05-75VC/100VC/125VC/150VC ■MS05-50VC ■MS05-100VC

■SpecificationsModel MS05-50 MS05-75 MS05-100 MS05-125 MS05-150

Stroke mm 50 75 100 125 150

Minimum overall length A 154 211 236 261 286

Cylinder external diameter ϕ C 46 45

Piston diameter ϕ D 26

Piston thread size E M20 x 1.5

Piston thread length G 25


Collar thread size M M45 x 1.5

Collar thread length N 23

Base thread size P — M20 x 1.5

Base thread depth Q — 24

Incomplete thread length R 3


VC-70-R3

S

≈ 46 ≈ 39

S-1R ≈ 53 ≈ 46

ROC-13R ≈ 49 ≈ 42

Coupler position T 20 43

Required oil volume cm3 36 54 72 90 108

Approx. weight kg 1.5 2.0 2.3 2.5 2.7

■Compatible attachmentsAttachment location Cylinder parts MS05-50 MS05-75 MS05-100 MS05-125 MS05-150

Piston thread

Cap R-5PM

Piston base RB-5M

Clevis CLF-5-1 (2)

Collar thread Flange 5FM

Base threadCylinder base — CB-5M

Clevis — CLM-5-1 (2)




50 kN (MS Series)


MS 05 - 50 VCMaximum output Attached coupler


Single-acting cylinder -NC : W/O couplerMS series Stroke (mm)



17



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■MS1-75VC to 300VC ■MS1-50VC ■MS1-100VC

■SpecificationsModel MS1-50 MS1-75 MS1-100 MS1-125 MS1-150 MS1-200 MS1-250 MS1-300

Stroke mm 50 75 100 125 150 200 250 300


Cylinder external diameter ϕ C 58


Piston thread size E M28 x 2



Collar thread size M M58 x 2


Base thread size P — M28 x 2

Base thread depth Q — 31



VC-70-R3

S

≈ 39

S-1R ≈ 45

ROC-13R ≈ 41

Coupler position T 20 47


Approx. weight kg 2.8 3.7 4.1 4.5 4.9 5.8 6.6 7.5

■Compatible attachmentsAttachment location Cylinder parts MS1-50 MS1-75 MS1-100 MS1-125 MS1-150 MS1-200 MS1-250 MS1-300

Piston thread

Cap R-10PM

Tilt saddle R-10SP

Piston base RB-10M

Clevis CLF-10-1 (2)




Maximum operating pressure 70 MPaMaximum output 100 kNCylinder internal diameter ϕ 43Effective area 14.52 cm2


100 kN (MS Series)




Single-acting cylinder -NC : W/O couplerMS series Stroke (mm)●The piston and the inside of the cylinder tube are plated.



18


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■S1-12VC/35VC

■S1-120VC ■S1-100VC

■S1-55VC

■S1-50VC/150VC/200VC/255VC/300VC

■S1-100VC

*The dimensions in parentheses show those of the S1-35VC.

■SpecificationsModel S1-12 S1-35 S1-55 S1-100 S1-50 S1-120 S1-150 S1-200 S1-255 S1-300

Stroke mm 12 35 55 100 50 120 150 200 255 300Minimum overall length A 81 136 130 235 201 280 300 369 414 471Cylinder external diameter ϕ C 57Piston diameter ϕ D 28 37 38Piston thread size E — 1 1/4-11.5NPTPiston thread length G — 30Piston protrusion length H 11 10 19 32Collar thread size M 2 1/4-14NSCollar thread length N 27 30Base thread size P — 1 1/4-11.5NPTBase thread depth Q — 25Incomplete thread length R 6


VC-70-R3S

≈ 46 ≈ 39S-1R ≈ 53 ≈ 46ROC-13R ≈ 49 ≈ 42

Coupler position T 21 25 25 25 40 50 40Required oil volume cm3 18 51 80 146 73 175 218 291 371 436Approx. weight kg 1.5 2.3 2.1 3.8 3.1 4.4 4.7 5.8 6.5 7.4

■Compatible attachmentsAttachment location Cylinder parts S1-12 S1-35 S1-55 S1-100 S1-50 S1-120 S1-150 S1-200 S1-255 S1-300

Piston threadCap With special head cover R-10P

Piston base — RB-10Clevis — CLF-10-A (B)

Collar thread Flange 10F





100 kN (S Series)








19



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SpecificationsModel MS2-75 MS2-100 MS2-125 MS2-150 MS2-200 MS2-250 MS2-300 MS2-500

Stroke mm 75 100 125 150 200 250 300 500Minimum overall length A 269 294 319 372 410 460 510 710

Cylinder external diameter ϕ C 82


Piston thread size E M40 x 2



Collar thread size M M82 x 2


Base thread size P M40 x 2

Base thread depth Q 39



VC-70-R3

S

≈ 46 ≈ 80

S-1R ≈ 53 ≈ 87

ROC-13R ≈ 49 ≈ 83

Coupler position T 61

Required oil volume cm3 216 288 360 432 575 719 863 1437Approx. weight kg 8.2 9.0 9.8 11.7 12.5 14.1 16.0 21.3

■Compatible attachmentsAttachment location Cylinder parts MS2-75 MS2-100 MS2-125 MS2-150 MS2-200 MS2-250 MS2-300 MS2-500

Piston thread

Cap R-20PM

Tilt saddle R-20SP

Piston base RB-20M

Clevis CLF-20-1 (2)


Base threadCylinder base CB-20M

Clevis CLM-20-1 (2)



200 kN (MS Series)




Single-acting cylinder -NC : W/O couplerMS series Stroke (mm)

■MS2-200VC/250VC/300VC/500VC ■MS2-75VC/100VC/125VC/150VC ■MS2-100VC



* Male-and-female sockets are attached to the MS2-200/250/300/500. Be sure to use these sockets even when connecting a pipe directly without a coupler.


20


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■S2-25VC/50VC

■S2-70VC/126VC/200VC ■S2-250VC/320VC/510VC

■S2-70VC

■SpecificationsModel S2-25 S2-50 S2-70 S2-126 S2-200 S2-250 S2-320 S2-510

Stroke mm 25 50 70 126 200 250 320 510Minimum overall length A 127 160 230 285 360 450 513 703Cylinder external diameter ϕ C 86Piston diameter ϕ D 45 57Piston thread size E — 2-11.5NPTPiston thread length G — 27Piston protrusion length H 16 15 28Collar thread size M 3 5/16-12NSCollar thread length N 51Base thread size P — 2-11.5NPTBase thread depth Q — 27Incomplete thread length R 6


VC-70-R3S

≈ 46 ≈ 76S-1R ≈ 53 ≈ 83ROC-13R ≈ 49 ≈ 79

Coupler position T 25 48 47Required oil volume cm3 83 166 233 419 664 830 1062 1693Approx. weight kg 4.6 5.8 8.0 9.7 12.3 14.5 17.0 25.0

■Compatible attachmentsAttachment location Cylinder parts S2-25 S2-50 S2-70 S2-126 S2-200 S2-250 S2-320 S2-510

Piston threadCap With special head cover R-20P

Piston base — RB-20Clevis — CLF-20-A (B)






200 kN (S Series)




Single-acting cylinder -NC : W/O couplerS series Stroke (mm)●The piston and the inside of the cylinder tube are plated.


* Male-and-female sockets are attached to the S2-250/320/510. Be sure to use these sockets even when connecting a pipe directly without a coupler.


21



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■S5-25VC

■S5-50VC

■S3-50VC/125VC/200VC/S4-125VC ■S5-25VC


Maximum output kN 300 400 500Effective area cm2 44.17 57.77 71.63

Stroke mm 50 125 200 125 25 50

Minimum overall length A 226 300 376 299 100 176

Cylinder internal diameter ϕ 75 85.77 95.5



Piston thread size E M65 x 2 M70 x 2 —

Piston protrusion length H 35 35 — 21

Collar thread size M M100 x 2 M115 x 2 — M127 x 2.5

Collar thread length N 59 60 — 55

Base thread size P M65 x 2 M70 x 2 —

Base thread depth Q 30 30 —

Incomplete thread length R 6 6 — 6


VC-70-R3

S

≈ 46 ≈ 46 ≈ 46

S-1R ≈ 53 ≈ 53 ≈ 53

ROC-13R ≈ 49 ≈ 49 ≈ 49

Coupler position T 50 52 52 35 30

Required oil volume cm3 221 553 884 723 180 359Approx. weight kg 11.7 15.3 19.0 19.5 9.4 13.8


Piston threadCap R-30P R-40P — With special head cover

Piston base RB-30 RB-40 —

Collar thread Flange 30F — — 50FBase thread Cylinder base CB-30 CB-40 —

Maximum operating pressure 70 MPaMaximum output 300/400/500 kNCylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8

300 to 500 kN (S Series)


Ｓ 3 - 50 VCMaximum output Attached coupler

3 : 300 kN VC : VC-70-R34 : 400 kN S : S-1R5 : 500 kN T : ROC-13R





22


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■S5-53VC/100VC/153VC/S7-100VC

■S7-25VC ■S7-50VC

■S5-53VC


Maximum output kN 500 700

Effective area cm2 71.63 102.69

Stroke mm 53 100 153 25 50 100


Cylinder internal diameter ϕ 95.5 114.35


Piston diameter ϕ D 88.5 78 100 95

Piston thread size E M92 x 2.5 — M90 x 2

Piston protrusion length H 27 — 21 35

Collar thread size M M127 x 2.5 — M150 x 3

Collar thread length N 55 — 60

Incomplete thread length R 6 — 6


VC-70-R3

S

≈ 46 ≈ 46

S-1R ≈ 53 ≈ 53

ROC-13R ≈ 49 ≈ 49


Required oil volume cm3 380 717 1096 257 514 1027

Approx. weight kg 18.0 22.0 26.0 16.5 22.6 31.5


Piston threadCap R-50P — With special head cover R-70P

Piston base RB-50 —

Collar threadFlange 50F —

Lifting handle TH-127 —

Maximum operating pressure 70 MPaMaximum output 500/700 kNCylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8

500 to 700 kN (S Series)



5 : 500 kN VC : VC-70-R37 : 700 kN S : S-1R

T : ROC-13RSingle-acting cylinder -NC : W/O coupler

S series Stroke (mm)




23

Single-Acting Cylinders (load-return type)


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SpecificationsModel R04-15 R04-30 R1-30 R1-63 MR1-63 RJ1-63

Maximum output kN 40 100Effective area cm2 6.42 14.52Cylinder return force kN ≈ 0.07 ≈ 0.15Stroke mm 15 30 30 63Minimum overall length A 44 60 89 125Cylinder internal diameter ϕ 28.6 43Cylinder external diameter ϕ C 41 57Piston diameter ϕ D 20 37Piston protrusion length H 1 11Piston hole length K — 30Collar thread size M — — 2 1/4-14NS M58 x 2 —Collar thread length N — — 30 25 —Incomplete thread length R — — 6 —


VC-70-R3S

≈ 46 ≈ 46S-1R ≈ 53 ≈ 53ROC-13R ≈ 49 ≈ 49

Coupler position T 17 21 25Boss length U 19.5 18 17Required oil volume cm3 10 20 44 92 92 92Approx. weight kg 0.6 0.8 1.7 2.3 2.3 2.4 ■Compatible attachmentsAttachment location Cylinder parts R04-15 R04-30 R1-30 R1-63 MR1-63 RJ1-63

Piston Tilt saddle — R-1020SP

Collar thread Flange — — 10F 10FM —

Maximum operating pressure 70 MPaMaximum output 40/100 kNCylinder system Single-actingReturn system Load-returnCoupler connection port size Rc3/8

40 to 100 kN (R/MR/RJ Series)


Ｒ 04 - 15 VCMaximum output Attached coupler

Single-acting cylinder 04 : 40 kN VC : VC-70-R3R series 1 : 100 kN S : S-1R

MR series T : ROC-13RRJ series -NC : W/O coupler

Stroke (mm)*For the MR and RJ series, only 100 kN type is available as the maximum output.

■R1-30VC

■RJ1-63VC

■R04-15VC/30VC

■MR1-63VC/R1-63VC

■R04-15VC




24

Single-Acting Cylinders (load-return type) H

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■R2-50VC/R3-50VC

■R10-50VC

■R2-10VC

■R5-50VC

■R2-50VC

■SpecificationsModel R2-10 R2-50 R3-50 R5-50 R10-50

Maximum output kN 200 300 500 1000

Effective area cm2 33.18 44.17 71.63 146.55

Cylinder return force kN ≈ 0.35 ≈ 0.45 ≈ 0.75 ≈ 1.5

Stroke mm 10 50 50 50 50

Minimum overall length A 72 127 134 151 183

Cylinder internal diameter ϕ 65 75 96 136.6

Cylinder external diameter ϕ C 86 102 127 175


Head cover diameter ϕ F — 54 54 65 90

Piston protrusion length H 1 16 16 16 21


VC-70-R3

S

≈ 46 ≈ 46 ≈ 46 ≈ 46

S-1R ≈ 53 ≈ 53 ≈ 53 ≈ 53

ROC-13R ≈ 49 ≈ 49 ≈ 49 ≈ 49


Boss length U 19 17 19 19 —

Required oil volume cm3 34 166 221 359 733

Approx. weight kg 3.3 5.1 7.5 13.0 30.0

*Cylinder parts and attachments cannot be attached to the above cylinders.

Maximum operating pressure 70 MPa

Maximum output 200/300/500/1000 kN

Cylinder system Single-acting

Return system Load-return

Coupler connection port size Rc3/8

200 to 1000 kN (R Series)


R 2 - 10 VCMaximum output Attached coupler


10 : 1000 kN -NC : W/O couplerStroke (mm)

Single-acting cylinderR series




25

Double-Acting Cylinders


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■D04-85VC/150VC/200VC ■D04-250VC ■D04-50VC ■D04-50VC

■SpecificationsModel D04-50 D04-85 D04-150 D04-200 D04-250

Stroke mm 50 85 150 200 250Minimum overall length A 172 220 287 337 386Cylinder external diameter ϕ C 45 46Piston diameter ϕ D 22Piston thread size E M18 x 1.5Piston protrusion length H 32 33Cap thread size J 3/4-14NPTCap thread length K 24Collar thread size M M45 x 1.5Collar thread length N 23Base thread size P — 3/4-14NPTBase thread depth Q — 21Incomplete thread length R 3 4 3

Coupler pro-trusion length

VC-70-R3S (push side) V (pull side)

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position on the push side T 17 47Boss length on the push side U — 18 19 17Coupler position on the pull side W 45Boss length on the pull side X 17 18 19 17Distance between the ports Y 78 96 162 212 261Required oil volume cm3 33 55 97 129 161Approx. weight kg 2.0 2.6 3.3 3.9 4.3

■Compatible attachmentsAttachment location Cylinder parts D04-50 D04-85 D04-150 D04-200 D04-250

Cap threadCap R-4P

Piston base RB-4Clevis CLF-4-A (B)

Collar thread Flange 4FD



Maximum operating pressure 70 MPaMaximum output on the push side 40 kNEffective area on the push side 6.42 cm2

Cylinder internal diameter ϕ 28.6Maximum output on the pull side 16.3 kNEffective area on the pull side 2.62 cm2

Cylinder system Double-acting Coupler connection port size Rc3/8

40 kN (D Series)


D 04 - 50 VCAttached coupler

Double-acting cylinder VC : VC-70-R3Ｄ series S : S-1R

Maximum output T : ROC-13R04 : 40 kN -NC : W/O coupler

Stroke (mm)● The piston is plated.


* The dimensions in parentheses show those of the D04-85VC.


26

Double-Acting CylindersH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■MD05-75VC ■MD05-100VC to 250VC ■MD05-50VC ■MD05-100VC


Cylinder internal diameter ϕ 30.2Maximum output on the pull side 23.4 kNEffective area on the pull side 3.36 cm2

Cylinder system Double-actingCoupler connection port size Rc3/8

■SpecificationsModel MD05-50 MD05-75 MD05-100 MD05-150 MD05-200 MD05-250

Stroke mm 50 75 100 150 200 250Minimum overall length A 159 254 279 329 379 429Cylinder external diameter ϕ C 46Piston diameter ϕ D 22Piston thread size E M20 x 1.5Piston thread length G 25Piston protrusion length H 34Collar thread size M M45 x 1.5Collar thread length N 23Base thread size P — M20 x 1.5Base thread depth Q — 24Incomplete thread length R 3



≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position on the push side T 20 36Boss length on the push side U 17 —Coupler position on the pull side W 46Boss length on the pull side X 17 19Distance between the ports Y 59 138 163 213 263 313Required oil volume cm3 36 54 72 108 144 179Approx. weight kg 1.9 2.8 3.0 3.5 4.0 4.5

■Compatible attachmentsAttachment location Cylinder parts MD05-50 MD05-75 MD05-100 MD05-150 MD05-200 MD05-250

Piston threadCap R-5PM

Piston base RB-5MClevis CLF-5-1 (2)




50 kN (MD Series)


MD 05 - 50 VCAttached coupler

Double-acting cylinder VC : VC-70-R3MD series S : S-1R





27



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■MD1-100VC to 300VC ■MD1-50VC ■MD1-150VC


Stroke mm 50 100 150 200 250 300Minimum overall length A 244 320 370 420 470 520Cylinder external diameter ϕ C 59Piston diameter ϕ D 30Piston thread size E M28 x 2Piston thread length G 32Piston protrusion length H 42Length of piston stop ring L 9Collar thread size M M58 x 2Collar thread length N 25Base thread size P — M28 x 2Base thread depth Q — 31Incomplete thread length R 3



S (push side) ≈ 46 V (pull side) ≈ 46S-1R S (push side) ≈ 53 V (pull side) ≈ 53ROC-13R S (push side) ≈ 49 V (pull side) ≈ 49

Coupler position on the push side T 20 46Coupler position on the pull side W 57Boss length on the pull side X 20Distance between the ports Y 125 175 225 275 325 375Required oil volume cm3 73 146 218 291 365 436Approx. weight kg 4.0 5.2 6.0 6.8 7.6 8.3


Piston thread

Cap R-10PMTilt saddle R-10SP






Cylinder internal diameter ϕ 43Maximum output on the pull side 51.3 kNEffective area on the pull side 7.45 cm2


100 kN (MD Series)








28


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■D1-50VC to 300VC ■D1-50VC

■SpecificationsModel D1-50 D1-100 D1-150 D1-200 D1-260 D1-300

Stroke mm 50 100 150 200 260 300Minimum overall length A 231 281 330 381 440 481Cylinder external diameter ϕ C 58Piston diameter ϕ D 30Piston thread size E M28 x 2Piston protrusion length H 37Cap thread size J 1 1/4-11.5NPTCap thread length K 30Length of piston stop ring L 9Collar thread size M 2 1/4-14NSCollar thread length N 25Base thread size P 1 1/4-11.5NPTBase thread depth Q 25Incomplete thread length R 5



≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position on the push side T 40Coupler position on the pull side W 57Boss length on the pull side X 20Distance between the ports Y 97 147 196 247 306 347Required oil volume cm3 73 146 218 291 378 436Approx. weight kg 3.3 4.5 5.3 6.1 6.9 7.5

■Compatible attachmentsAttachment location Cylinder parts D1-50 D1-100 D1-150 D1-200 D1-260 D1-300

Cap threadCap R-10P



Base threadCylinder base CB-10

Clevis CLM-10-A (B)


Cylinder internal diameter ϕ 43Maximum output on the pull side 51.3 kNEffective area on the pull side 7.45 cm2


100 kN (D Series)



Double-acting cylinder VC : VC-70-R3D series S : S-1R





29



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■MD2-100VC to 500VC ■MD2-50VC ■MD2-100VC


Stroke mm 50 100 150 200 300 500Minimum overall length A 244 395 445 495 595 795Cylinder external diameter ϕ C 82 83Piston diameter ϕ D 42Piston thread size E M40 x 2Piston thread length G 36Piston protrusion length H 45Length of piston stop ring L 10Collar thread size M M82 x 2Collar thread length N 50Base thread size P — M40 x 2Base thread depth Q — 39Incomplete thread length R 6 5



≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position on the push side T 20 57Coupler position on the pull side W 83Boss length on the pull side X 19 20Distance between the ports Y 96 210 260 310 410 610Required oil volume cm3 144 288 432 575 863 1437Approx. weight kg 8.2 13.0 14.6 16.1 19.3 25.5


Piston thread

Cap R-20PMTilt saddle R-20SP






Cylinder internal diameter ϕ 60.5Maximum output on the pull side 103 kNEffective area on the pull side 14.89 cm2


200 kN (MD Series)








30


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■D2-100VC to 500VC　 ■D2-55VC ■D2-100VC


Stroke mm 55 100 150 200 302 502Minimum overall length A 197 331 380 431 532 732Cylinder external diameter ϕ C 86 87Piston diameter ϕ D 44.37Piston thread size E M40 x 3Piston protrusion length H 47 45Cap thread size J 2-11.5NPTCap length K 40Length of piston stop ring L — 10Collar thread size M 3 5/16-12NSCollar thread length N 48 51Base thread size P — 2-11.5NPTBase thread depth Q — 27Incomplete thread length R 6 5

Push side coupler protrusion length

VC-70-R3S

≈ 46 ≈ 80S-1R ≈ 53 ≈ 87ROC-13R ≈ 49 ≈ 83

Coupler position on the push side T 25 43Pull sidecoupler protrusion length

VC-70-R3V

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position on the pull side W 70 83Boss length on the pull side X 17 20Distance between the ports Y 55 160 209 260 361 561Required oil volume cm3 183 332 498 664 1002 1666Approx. weight kg 7.1 11.8 13.5 15.1 18.4 25.5


Cap threadCap R-20P






Cylinder internal diameter ϕ 65Maximum output on the pull side 106 kNEffective area on the pull side 17.72 cm2


200 kN (D Series)



Double-acting cylinder VC : VC-70-R3D series S : S-1R




* A male-and-female socket is attached to the push port of the cylinder. Be sure to use the male-and-female socket even if no coupler is used.


31



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SpecificationsModel D3.5-100 D3.5-150 D3.5-300 D5-50 D5-100 D5-150 D5-300 D5-500

Stroke mm 100 150 300 50 100 150 300 500Minimum overall length A 346 396 545 288 338 387 589 789Cylinder external diameter ϕ C 110 128 127Piston diameter ϕ D 56 63.42Piston thread size E M50 x 2 M55 x 3Piston protrusion length H 53 60Cap thread size J — M92 x 2.5Cap thread length K — 28Length of piston stop ring L 7 12Collar thread size M M110 x 2.5 M127 x 2.5Collar thread length N 55 55Base thread size P M50 x 2 — M55 x 3Base thread depth Q 35 — 55Incomplete thread length R 5 3


VC-70-R3S

(push side) V

(pull side)

≈ 46 —S-1R ≈ 53 —ROC-13R ≈ 49 —VC-70-R4 — ≈ 45S-24R — ≈ 56

Coupler position on the push side T 73.5 25 84Coupler position on the pull side W 80.5 91 89Distance between the ports Y 139 189 338 112 162 211 356 556Required oil volume cm3 503 754 1508 359 717 1075 2149 3582Approx. weight kg 20.0 23.5 30.8 24.5 28.0 31.5 46.0 60.5 ■Compatible attachmentsAttachment location Cylinder parts D3.5-100 D3.5-150 D3.5-300 D5-50 D5-100 D5-150 D5-300 D5-500

Piston thread (D3.5) Cap R-35P R-50PPiston base RB-35 RB-50

Cap thread (D5) Clevis CLF-35-1 (2) CLF-50-1 (2)*

Collar threadFlange 35F 50F

Lifting handle — TH-127

Base threadCylinder base CB-35 — CB-50

Clevis CLM-35-1 (2) — CLM-50-1 (2)*For the D5 series, remove the thread cap before screwing a clevis to the piston thread.

D3.5 D5Maximum operating pressure 70 MPaMaximum output on the push side 350 kN 500 kNEffective area on the push side 50.26 cm2 71.63 cm2

Cylinder internal diameter ϕ 80 ϕ 95.5Maximum output on the pull side 178 kN 279 kNEffective area on the pull side 25.63 cm2 40.04 cm2

Cylinder system Double-actingCoupler connection port size Rc3/8 Rc1/2

350 to 500 kN (D Series)



Maximum output3.5 : 350 kN D3.5 series D5 series

5 : 500 kN VC : VC : VC-70-R4Double-acting cylinder S : S-1R C : S-24R

D series　　　　　　　Stroke T : ROC-13R -NC : W/O coupler (mm) -NC : W/O coupler

● The piston is plated.


■D3.5-100VC to 300VC ■D5-50VC/100VC/150VC ■D5-300VC/500VC


32


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■D10-50VC/150VC ■D20-150VC/300VC

■D10-300VC ■D10-500VC ■D20-500VC/1000VC

■D10-150VC

■SpecificationsModel D10-50 D10-150 D10-300 D10-500 D20-150 D20-300 D20-500 D20-1000

Stroke mm 50 150 300 500 150 300 500 1000Minimum overall length A 320 447 598 912 473 623 959 1459Cylinder external diameter ϕ C 171 185 241 240 255Piston diameter ϕ D 95.15 136.42Piston thread size E M90 x 3 M120 x 4Piston protrusion length H 67 70 78Length of piston stop ring L 7 7Collar thread size M M170 x 3 M185 x 3 M240 x 4 M255 x 4Collar thread length N 65 73Incomplete thread length R 5 5


VC-70-R4 S (push side) V (pull side)

≈ 45 ≈ 45S-24R ≈ 56 ≈ 56

Coupler position on the push side T 30 40 35 40Coupler position on the pull side W 101 107 114Distance between the ports Y 122 246 397 695 246 396 727 1227Required oil volume cm3 733 2199 4397 7328 4279 8558 14263 28526Approx. weight kg 46 62 81 152 130 169 268 450

■Compatible attachmentsAttachment location Cylinder parts D10-50 D10-150 D10-300 D10-500 D20-150 D20-300 D20-500 D20-1000

Piston threadCap R-100P R-200P

Piston base RB-100 —

Collar threadFlange 100F 100FB 200F 200FB

Lifting handle TH-170 TH-185 TH-240 TH-255

D10 D20Maximum operating pressure 70 MPaMaximum output on the push side 1000 kN 2000 kNEffective area on the push side 146.55 cm2 285.26 cm2

Cylinder internal diameter ϕ 136.6 ϕ 190.6Maximum output on the pull side 515 kN 976 kNEffective area on the pull side 75.44 cm2 139.09 cm2


1000 to 2000 kN (D Series)



Maximum output VC : VC-70-R410 : 1000 kN C : S-24R20 : 2000 kN -NC : W/O coupler

Double-acting cylinderD series Stroke (mm)● The piston is plated.


* The dimensions in parentheses show those of the D20-500VC and D20-1000VC.


33



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■D50-300-NC ■D50-500-NC ■D50-850-NC

■D30-300-NC ■D30-500-NC ■D30-850-NC

■D30-500-NC


Stroke mm 300 500 850 300 500 850


Cylinder external diameter ϕ C 315 410

Piston diameter ϕ D 170 220

Piston thread size E M150 x 3 M180 x 4

Piston protrusion length H 86 90

Length of piston stop ring L 9 —

Collar thread size M M315 x 4 M410 x 6

Collar thread length N 89 97

Incomplete thread length R 4 5

Push port position T 45 50

Pull port position W 148 147

Distance between the ports Y 532 731 1081 604 804 1154

Required oil volume cm3 13012 21687 36867 21902 36502 62054

Approx. weight kg 398 494 650 740 928 1164


Piston thread Cap R-300P R-500P

Collar threadFlange 300F 500F

Lifting handle TH-315 —

D30 D50Maximum operating pressure 70 MPaMaximum output on the push side 3000 kN 5000 kNEffective area on the push side 433.73 cm2 730.04 cm2

Cylinder internal diameter ϕ 235 ϕ 304.88Maximum output on the pull side 1430 kN 2390 kNEffective area on the pull side 206.75 cm2 349.9 cm2

Cylinder system Double-actingCoupler connection port size Rc3/4 Rc1

3000 to 5000 kN (D Series) Make-to-order product 　


D 30 - 300 -NC-NC : W/O coupler

Maximum output30 : 3000 kN50 : 5000 kN

Double-acting cylinderD series Stroke (mm)● The piston is plated.

● All models include no couplers.



34


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■SD04-100-NC to 200-NC ■SD1-150-NC to 250-NC

■SD2-50-NC to 100-NC ■SD2-100-NC

■SpecificationsModel SD04-100 SD04-150 SD04-200 SD1-150 SD1-250 SD2-50 SD2-75 SD2-100

Stroke mm 100 150 200 150 250 50 75 100



Piston diameter ϕ D 20 30 45

Piston thread size E M18 x 1.5 M26 x 2 M40 x 2

Piston thread length G 26 30 37

Piston protrusion length H 43 51 58

Length of piston stop ring L 25 30 10



Bottom cap external diameter ϕ P 63 76 —

Bottom cap length Q 60 72 —


Wrench catcher (width across flats) T 15 22 35

Pull port position W 77 87 84

Boss length on the pull side X 19 20 20


Approx. weight kg 4.2 4.7 5.2 8.3 9.5 11.0 11.8 12.5

■Compatible attachmentsAttachment location Cylinder parts SD04-100 SD04-150 SD04-200 SD1-150 SD1-250 SD2-50 SD2-75 SD2-100

Piston threadCap Make-to-order product Make-to-order product R-20PM

Piston base Make-to-order product Make-to-order product RB-20MClevis Make-to-order product Make-to-order product CLF-20-1(2)

Collar thread Flange 5FM Make-to-order product Make-to-order product

● More durable than standard cylinders. Suitable for frequent use.● All models include no couplers. ● A wrench catcher is provided on the piston.● Cylinders whose stroke is not listed below can be manufactured. Please contact us for further information.

SD04 SD1 SD2Maximum operating pressure 70 MPaMaximum output on the push side 40 kN 100 kN 200 kNEffective area on the push side 6.42 cm2 14.52 cm2 29.22 cm2

Cylinder internal diameter ϕ 28.6 ϕ 43 ϕ 61Maximum output on the pull side 20.4 kN 51.3 kN 91.2 kNEffective area on the pull side 3.28 cm2 7.45 cm2 13.32 cm2


40 to 200 kN Strong-Type Double-Acting Cylinders (SD Series) Make-to-order product


SD 04 - 100 -NCMaximum output -NC : W/O coupler

04 : 40 kN1 : 100 kN2 : 200 kN

Strong-type double-acting cylinderSD series Stroke (mm)

* The dimensions in parentheses show those of the SD1 series.


35



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SpecificationsModel SD3.5-100 SD3.5-150 SD5-50 SD5-100 SD5-150 SD7-100 SD7-150 SD7-200

Stroke mm 100 150 50 100 150 100 150 200



Piston diameter ϕ D 55 63 80

Piston thread size E M50 x 2 M57 x 2 M75 x 2

Piston thread length G 45 55 55






Wrench catcher (width across flats) T 44 52 68

Pull port position W 93 102 112


Approx. weight kg 23 26 32 36 40 57 63 68

■Compatible attachmentsAttachment location Cylinder parts SD3.5-100 SD3.5-150 SD5-50 SD5-100 SD5-150 SD7-100 SD7-150 SD7-200

Piston thread

Cap R-35P Make-to-order product Make-to-order product

Piston base RB-35 Make-to-order product Make-to-order product

Clevis CLF-35-1 (2) Make-to-order product Make-to-order product

Collar thread Flange 35F Make-to-order product Make-to-order product

SD3.5 SD5 SD7Maximum operating pressure 70 MPaMaximum output on the push side 350 kN 500 kN 700 kNEffective area on the push side 50.26 cm2 71.63 cm2 102.69 cm2

Cylinder internal diameter ϕ 80 ϕ 96 ϕ 114.35Maximum output on the pull side 184 kN 282 kN 357 kNEffective area on the pull side 26.5 cm2 40.45 cm2 52.43 cm2

Cylinder system Double-actingCoupler connection port size Rc3/8 Rc1/2

● More durable than standard cylinders. Suitable for frequent use.● All models include no couplers. ● A wrench catcher is provided on the piston.● Cylinders whose stroke is not listed below can be manufactured. Please contact us for further information.



3.5 : 350 kN5 : 500 kN7 : 700 kN

Strong-type double-acting cylinderSD series Stroke (mm)


■SD5-50-NC/100-NC/150-NC ■SD7-100-NC/150-NC/200-NC

■SD3.5-100-NC/150-NC


36


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


● More durable than standard cylinders. Suitable for frequent use.● All models include no couplers. ● A wrench catcher is provided on the piston. (SD10 only) ● Cylinders whose stroke is not listed below can be manufactured. Please contact us for further information.

■SpecificationsModel SD10-150 SD10-300 SD20-150 SD20-300 SD30-200 SD30-300 SD50-200 SD50-300

Stroke mm 150 300 150 300 200 300 200 300




Piston thread size E M90 x 3 M130 x 3 M160 x 3 M200 x 3

Piston thread length G 65 70 80 80


Length of piston stop ring L 12 12 12 15

Collar thread size M M190 x 3 M265 x 4 M325 x 4 M420 x 6

Collar thread length N 65 70 90 95

Incomplete thread length R 4 4 4 5

Coupler connection port size T Rc1/2 Rc1/2 Rc3/4 Rc1

Pull port position W 122 152 172 203


Approx. weight kg 102 128 241 292 436 487 830 914

■Compatible attachmentsAttachment location Cylinder parts SD10-150 SD10-300 SD20-150 SD20-300 SD30-200 SD30-300 SD50-200 SD50-300

Piston threadCap R-100P Make-to-order product Make-to-order product Make-to-order product

Piston base RB-100 Make-to-order product Make-to-order product Make-to-order product

Collar thread Flange Make-to-order product Make-to-order product Make-to-order product Make-to-order product

SD10 SD20 SD30 SD50Maximum operating pressure 70 MPaMaximum output on the push side 1000 kN 2000 kN 3000 kN 5000 kNEffective area on the push side 146.55 cm2 292.55 cm2 433.73 cm2 730.04 cm2

Cylinder internal diameter ϕ 136.6 ϕ 193 ϕ 235 ϕ 304.88Maximum output on the pull side 516 kN 948 kN 1430 kN 2390 kNEffective area on the pull side 75.66 cm2 138.61 cm2 206.75 cm2 349.9 cm2

Cylinder system Double-actingCoupler connection port size Rc1/2 Rc3/4 Rc1



10 : 1000 kN20 : 2000 kN30 : 3000 kN50 : 5000 kN Stroke (mm)

Strong-type double-acting cylinder SD series


■SD20-150-NC/300-NC ■SD30-200-NC/300-NC ■SD50-200-NC/300-NC

■SD10-150-NC/300-NC


37

Single-Acting Cylinders


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SC2-40VC

■SC6-20VC

■SC1.2-40VC

■SC3.6-20VC/30VC

■SC2-40VC

■SpecificationsModel SC1.2-40 SC2-40 SC3.6-20 SC3.6-30 SC6-20

Stroke mm 40 40 20 30 20Minimum overall length A 126.5 165 141 161 170Center hole diameter ϕ B 19.5 27.5 36.5 54.5Cylinder external diameter ϕ C 70 97 127 170Piston diameter ϕ D 35 48 70 95Piston protrusion length H 1.5 1 1 3


VC-70-R3S

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position T 40 30 32 32Required oil volume cm3 72 116 103 155 178Approx. weight kg 3.0 7.8 11.3 12.7 25.0 ■Pressure gauges with load scale (regular stock item)

● These pressure gauges have not only a pressure scale but also a load scale corre-sponding to the cylinder effective area. (Indicated loads are conversion values.)

● Other than the models shown below, pressure gauges with a load scale are make-to-order products.

● None of inspection report, traceability system diagram, and calibration certificate are included. If necessary, please let us know your request when ordering. (For details, see page 162.)

Model Effective area (cm2) Compatible cylinder AS100-120 kN 17.86 SC1.2AS100-200 kNSC 28.86 SC2AS100-360 kN 51.42 SC3.6

SC1.2 SC2 SC3.6 SC6


Maximum output 120 kN 200 kN 360 kN 600 kN

Effective area (cm2) 17.86 28.86 51.42 88.55

Cylinder internal diameter ϕ 54 ϕ 70 ϕ 95.5 ϕ 130


Return system Spring-return


120 to 600 kN Center Hole Cylinders (SC Series)


SC 1.2 - 40 VCMaximum output Attached coupler

1.2 : 120 kN VC : VC-70-R32 : 200 kN S : S-1R

3.6 : 360 kN T : ROC-13R6 : 600 kN -NC : W/O coupler

Stroke (mm)Single-acting center hole cylinder

SC series

■AS100-120 kN

● A through-hole is provided at the center of the piston, and is useful for various tensile testings and tension units.● The SC6-20 has a handle.


38


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■DC3-100VC/200VC ■DC4-100VC/200VC ■DC5-100VC/200VC

■DC2-100VC/200VC ■DC2-100VC

DC2 DC3 DC4 DC5


Maximum output on the push side 200 kN 300 kN 400 kN 500 kN

Effective area on the push side 30.63 cm2 47.87 cm2 58.31 cm2 74.61 cm2

Cylinder internal diameter ϕ 80 ϕ 95.5 ϕ 105 ϕ 120

Maximum output on the pull side 111 kN 207 kN 249 kN 332 kN

Effective area on the pull side 17.08 cm2 33.14 cm2 36.32 cm2 49.48 cm2

Cylinder system Double-acting


■SpecificationsModel DC2-100 DC2-200 DC3-100 DC3-200 DC4-100 DC4-200 DC5-100 DC5-200

Stroke mm 100 200 100 200 100 200 100 200


Center hole diameter ϕ B 40.5 42.5 47.5 55.5




Length of piston stop ring L 7 7 7 7

Collar thread size M M110 x 2 M127 x 2.5 M135 x 3 M165 x 3

Collar thread length N 35 40 40 45

Incomplete thread length R 5 5 5 5



≈ 46 ≈ 46 ≈ 46 ≈ 46

S-1R ≈ 53 ≈ 53 ≈ 53 ≈ 53

ROC-13R ≈ 49 ≈ 49 ≈ 49 ≈ 49

Coupler position on the push side T 30 25 25 25

Coupler position on the pull side W 67 65 70 72

Distance between the ports Y 136 236 168 268 168 268 176 276


Approx. weight kg 13.5 19.0 20.0 26.5 22.5 30.0 36.0 47.0

■Compatible attachmentsAttachment location Cylinder parts DC2-100 DC2-200 DC3-100 DC3-200 DC4-100 DC4-200 DC5-100 DC5-200

Collar threadFlange Make-to-order product 50F Make-to-order product Make-to-order product

Lifting handle TH-110 TH-127 TH-135 TH-165

● A through-hole is provided at the center of the piston, and is useful for various tensile testings and tension units.

200 to 500 kN Center Hole Cylinders (DC Series)


DC 2 - 100 VCMaximum output Attached coupler

2 : 200 kN VC : VC-70-R33 : 300 kN S : S-1R4 : 400 kN T : ROC-13R5 : 500 kN -NC : W/O coupler

Stroke (mm)Double-acting center hole cylinder

DC series


39



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■DC7-150VC ■DC10-150VC ■DC20-150VC

■DC7-150VC

■SpecificationsModel DC7-150 DC10-150 DC20-150

Stroke mm 150 150 150

Minimum overall length A 346 356 376

Center hole diameter ϕ B 62.5 78.5 108.5


Piston diameter ϕ D 110 136.6 190



Collar thread size M M185 x 3 M230 x 3 M315 x 4



Coupler protru-sion length

VC-70-R4S

≈ 45 ≈ 45 ≈ 45

S-24R ≈ 56 ≈ 56 ≈ 56

Coupler position on the push side T 30 30 30

Coupler position on the pull side W 82 92 107

Distance between the ports Y 226 226 231

Required oil volume cm3 1556 2309 4477

Approx. weight kg 57 89 180

■Compatible attachmentsAttachment location Cylinder parts DC7-150 DC10-150 DC20-150

Collar threadFlange 100FB Make-to-order product 300F

Lifting handle TH-185 TH-230 TH-315

● A through-hole is provided at the center of the piston, and is useful for various tensile testings and tension units.

DC7 DC10 DC20


Maximum output on the push side 700 kN 1000 kN 2000 kN

Effective area on the push side 103.67 cm2 153.93 cm2 298.45 cm2

Cylinder internal diameter ϕ 140 ϕ 175 ϕ 240

Maximum output on the pull side 398 kN 610 kN 1130 kN

Effective area on the pull side 58.9 cm2 93.97 cm2 168.86 cm2

Cylinder system Double-acting


700 to 2000 kN Center Hole Cylinders (DC Series)


DC 7 - 150 VCAttached coupler

Maximum output VC : VC-70-R47 : 700 kN C : S-24R

10 : 1000 kN -NC : W/O coupler20 : 2000 kN

Stroke (mm)Double-acting center hole cylinder

DC series


40

Single-Acting CylindersH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■RAL-20 ■RAL-50

■RAL-20

■SpecificationsModel SJ2-50AL SJ2-100AL SJ2-150AL SJ5-50AL SJ5-100AL SJ5-150AL SJ10-50AL

Stroke mm 50 100 150 50 100 150 50Minimum overall length A 167 225 290 188 248 318 242Cylinder external diameter ϕ C 98 134 192Piston diameter ϕ D 53 80 118Cap external diameter ϕ F 58 88 126Piston protrusion length H 17 20 26Base diameter ϕ P 92 126 182Base height Q 10 13 16Coupler protrusion length

VC-70-R3S

≈ 46 ≈ 46 ≈ 46S-1R ≈ 53 ≈ 53 ≈ 53ROC-13R ≈ 49 ≈ 49 ≈ 49

Coupler position T 22 22 32Required oil volume cm3 144 288 432 358 717 1075 733Approx. weight kg 4.5 5.6 6.9 9.3 11.5 13.7 26.0

■Dimension table Model ϕ A ϕ B C D Approx. weight (kg) Compatible cylinder

RAL-20 58 48 26 31.5 0.5 SJ2- * ALRAL-50 88.5 76 35 40.5 1.6 SJ5- * AL

● Suitable for when an eccentric load is applied. ● Maximum angle of oscillation: 5°

*RAL-100 tilt saddles were discontinued in 2013.

*The 300 kN series lightweight cylinders and the SJ10-100AL and SJ10-150AL (1000 kN) are discontinued.

*For the SJ10, the piston may not be returned completely only by the return spring force.

● This series uses super-high durable aluminum materials to reduce its weight to about half that of a standard cylinder. ● Special surface treatment for the entire part assures good wear resistance. ● While the cylinder is being used, the load must be received by the whole surfaces of the piston and base. ● If an eccentric load is unavoidable, use a tilt saddle (optional).

SJ2 SJ5 SJ10


Maximum output on the push side 200 kN 500 kN 1000 kN

Effective area on the push side 28.74 cm2 71.63 cm2 146.55 cm2

Cylinder internal diameter ϕ 60.5 ϕ 95.5 ϕ 136.6




200 to 1000 kN Lightweight Aluminum Cylinders for Jack-Up (SJ-AL Series)

Tilt Saddle for Lightweight Aluminum Cylinders (SJ-AL Series) for Jack-Up (Optional)


SJ 2 - 50 AL VCMaximum output Attached coupler

2 : 200 kN Lightweight VC : VC-70-R35 : 500 kN aluminum S : S-1R

10 : 1000 kN cylinder T : ROC-13RStroke (mm) -NC : W/O coupler

Single-acting lightweight aluminum cylinder for jack-upSJ series

■SJ2-50ALVC to 150ALVC ■SJ5-50ALVC to 150ALVC ■SJ10-50ALVC

■SJ2-50ALVC


41



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SJ2-126VC/SJ3-125VC/SJ4-125VC ■SJ5-54VC/154VC

■SJ2-50VC ■SJ1-100VC/150VC/255VC ■SJ2-50VC

■SpecificationsModel SJ1-100 SJ1-150 SJ1-255 SJ2-50 SJ2-126 SJ3-125 SJ4-125 SJ5-54 SJ5-154

Stroke mm 100 150 255 50 126 125 125 54 154

Minimum overall length A 248 298 412 160 271 270 270 200 300

Cylinder external diameter ϕ C 57 86 102 117 128

Piston diameter ϕ D 38 45 57 68 75 88.5

Piston thread size E 1 1/4-11.5NPT — — —

Head cover diameter ϕ F 50 42 70 68 75 88

Piston thread length G 25 — — —

Piston protrusion length H 45 15 31 25 20


VC-70-R3

S

≈ 39 ≈ 46 ≈ 46 ≈ 46

S-1R ≈ 46 ≈ 53 ≈ 53 ≈ 53

ROC-13R ≈ 42 ≈ 49 ≈ 49 ≈ 49

Coupler position T 25 25 31 30 35 35

Attached cap — R-10P Special cap Special cap Special cap

Required oil volume cm3 146 218 371 166 419 553 723 387 1104

Approx. weight kg 4.3 5.1 6.9 6.1 10.2 14.2 18.0 17.0 26.5

● A cap is attached to the tip of the piston of each cylinder.

SJ1 SJ2 SJ3 SJ4 SJ5


Maximum output 100 kN 200 kN 300 kN 400 kN 500 kN

Effective area (cm2) 14.52 33.18 44.17 57.77 71.63

Cylinder internal diameter ϕ 43 ϕ 65 ϕ 75 ϕ 85.78 ϕ 95.5




100 to 500 kN Cylinder for Jack-Up (SJ Series)


SJ 1 - 100 VCMaximum output Attached coupler

1 : 100 kN VC : VC-70-R32 : 200 kN S : S-1R3 : 300 kN T : ROC-13R4 : 400 kN -NC : W/O coupler5 : 500 kN Stroke (mm)

Single-acting cylinder for Jack-UpSJ series


42


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■SN5-200VC ■SN10-200VC

■SN2-200VC ■SN1-200VC ■SN1-200VC

■SpecificationsModel SN1-200 SN2-200 SN5-200 SN10-200

Stroke mm 200Minimum overall length A 368 387 410 485Cylinder external diameter ϕ C 57 86 128 173Piston diameter ϕ D 38 57 85 115Head cover diameter ϕ F 50 70 100 125Piston protrusion length H 35 38 28 33Safety nut diameter ϕ M 58 86 128 167Safety nut height N 25 35 45 70Hole diameter of safety nut R 4 x ϕ 8 4 x ϕ 10Square thread size P 38 x 5 57 x 6 85 x 8 115 x 10


VC-70-R3S

≈ 39 ≈ 46S-1R ≈ 46 ≈ 53ROC-13R ≈ 42 ≈ 49

Coupler position T 25 33 35 32Attached cap — Special capRequired oil volume cm3 291 664 1433 2931Approx. weight kg 6.0 14.0 33.5 72.0

● The safety nut tightened after jack-up can receive the load.● A cap is attached to the tip of the piston of each cylinder.

SN1 SN2 SN5 SN10


Maximum output 100 kN 200 kN 500 kN 1000 kN

Effective area (cm2) 14.52 33.18 71.63 146.55

Cylinder internal diameter ϕ 43 ϕ 65 ϕ 95.5 ϕ 136.6




100 to 1000 kN Cylinders with Safety Nut for Jack-Up (SN Series)


SN 1 - 200 VCMaximum output Attached coupler


10 : 1000 kN -NC : W/O couplerStroke (mm)

Single-acting cylinder for Jack-UpSN series


43



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■TS05-125VC ■TS1-125VC■TS1.5-125VC

■TS05-125VC

■LF3-10VC ■LF5-10VC ■LF7.5-10VC ■LF10-10VC ■LF3-10VC

■SpecificationsModel LF3-10 LF5-10 LF7.5-10 LF10-10

Minimum overall length A 34Cylinder external diameter ϕ C 112 132 154 174Piston diameter ϕ D 77 96 118 138Coupler protrusion length

VC-70-R3S

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position T 17Required oil volume cm3 46 73 110 150Approx. weight kg 2.6 4.1 5.5 6.2

■Dimension tableModel TS05-125 TS1-125 TS1.5-125

A 300 330 333B 203 260 270C 182 225 270D 75 100 125E 25 32 38F 60 60 60G 43 64 54T 42 63 68

SVC-70-R3 ≈ 46S-1R ≈ 53ROC-13R ≈ 49

● Super thin jack with a minimum overall length of 34 mm. ● The piston is allowed to be inclined at a maximum angle of 4°.

LF3 LF5 LF7.5 LF10Maximum operating pressure 70 MPaMaximum output 300 kN 500 kN 750 kN 1000 kNEffective area (cm2) 46.56 72.38 109.35 149.57Cylinder internal diameter ϕ 77 ϕ 96 ϕ 118 ϕ 138Minimum overall length 34 mmStroke 10 mmCylinder system Single-actingReturn system Load-returnCoupler connection port size Rc3/8

TS05 TS1 TS1.5Maximum operating pressure (toe part) 34.5 MPa 34.8 MPa 34.0 MPaMaximum operating pressure (head part) 68.9 MPa 69.6 MPa 68.0 MPaMaximum output (toe part) 50 kN 100 kN 150 kNMaximum output (head part) 100 kN 200 kN 300 kNStroke 125 mmEffective area (cm2) 14.52 28.74 44.17Cylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8Required oil volume (cm3) 182 360 553Approx. weight (kg) 21.5 41.0 59.0

300 to 1000 kN Super Flat Jack (LF Series)

50 to 150 kN Toe Jack (TS Series)


LF 3 - 10 VCMaximum output Attached coupler

3 : 300 kN VC : VC-70-R35 : 500 kN S : S-1R

7.5 : 750 kN T : ROC-13R10 : 1000 kN -NC : W/O coupler

Single-acting cylinder Stroke (mm)LF series


TS 05 - 125 VCMaximum output (toe part) Attached coupler

05 : 50 kN VC : VC-70-R31 : 100 kN S : S-1R

1.5 : 150 kN T : ROC-13RSingle-acting cylinder -NC : W/O coupler

TS series Stroke (mm)

Use the whole surface of the cylinder bottom on hard flat plane so that the jack supports the load stably.

The LF series cylinders have no piston stop ring. If the piston protrudes over 10 mm (beyond the stroke-end indicating groove), it will be ejected causing oil leakage. Moreover the cylinder may need repair.


44


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■MSP05-150VC　 ■SP05-150VC ■SP1-150VC

■SpecificationsModel MSP05-150 SP05-150 SP1-150

Minimum overall length A 460 470Cylinder external diameter ϕ C 59 58 71Piston diameter ϕ D 30Piston thread size E M28 x 2 M28 x 2 M28 x 2Piston thread length G 29 30 29Piston protrusion length H 184 187Cap thread J — 1 1/4-11.5NPT —Collar thread size M M58 x 2 2 1/4-14NS M70 x 2Collar thread length N 25Base thread size P M28 x 2 1 1/4-11.5NPT M28 x 2Base thread depth Q 25 30


VC-70-R3S

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler position T 219 226Boss length U 20Required oil volume cm3 112 213Approx. weight kg 4.6 4.5 6.9

■Compatible attachmentsAttachment location Cylinder parts MSP05-150 SP05-150 SP1-150Piston thread Cap R-10PM R-10P R-10PM(MSP05/SP1)

Piston base RB-10M RB-10 RB-10MCap thread(SP05) Clevis CLF-10-1(2) CLF-10-A(B) Make-to-order productCollar thread Flange 10FM 10F Make-to-order product

Base threadCylinder base CB-10M CB-10 CB-10M

Clevis CLM-10-1(2) CLM-10-A(B) Make-to-order product

MSP05 SP05 SP1Maximum operating pressure 70 MPaMaximum output 50 kN 100 kNEffective area 7.45 cm2 14.16 cm2

Cylinder internal diameter ϕ 43 ϕ 52Stroke 150 mmCylinder system Single-actingReturn system Spring-returnCoupler connection port size Rc3/8

● The cylinder with a stroke sensor detects positions using the built-in rotary encoder, which reduces the size and im-proves the accuracy of the equipment.

● The roller in contact with the piston changes the linear motion of the piston into rotary motion. The incremental rotary encoder connected to the roller converts this rotary motion into an electrical pulse and outputs it.

● Mounted on the top of the cylinder and can be handled as a conventional cylinder. ● Generates no backlash and is highly durable.

■Sensor specificationsPower voltage 12 VDC ± 0.5 % Power current 40 mA max.Output waveform Rectangular wave Output phase A/B

Resolution 600 pulse/rev 0.1 mm/pulse Display accuracy ± (0.1+0.01/60 x L)

L: Cylinder stroke (mm)A/B phase difference 90° ± 45° Light source LEDLight source life 50,000 hours Output impedance 2.2 kΩResponse speed 10 kHz Travel distance 300 km

Output signal1 (High) +11 V min. Operating temperature range 5 to 50 °C0 (Low) +1 V max. Upper limit of operating humidity 90 %RH (no condensation)

*The counter is optional. *If the sequencer counts, set the cylinder speed that is appropriate for the maximum frequency of the two-phase counter of the sequencer. *The cylinder speed must be 500 mm/s or below.*To avoid accumulated errors, provide an external switch to set a reference point, or execute a zero reset once several strokes at the stroke end. *If the sensor cable length is 20 m or longer, the use of an open collector is recommended for the final output stage.

50 to 100 kN Pull Cylinders (MSP Series/SP Series)

Hydraulic Cylinder with Stroke Sensor Make-to-order product


SP 05 - 150 VCMaximum output Attached coupler

05 : 50 kN VC : VC-70-R31 : 100 kN S : S-1R

Single-acting pull cylinder T : ROC-13RSP series -NC : W/O coupler

MSP series Stroke (mm)*For the MSP series, only 50 kN is available as the maximum output.

■MSP05-150VC ■SP1-150VC

* The piston may not be returned to the stroke-end completely only by the return spring force depending on the aged deterioration or the operating conditions.

■SP05 cap part　　　　　　

*The dimensions in parentheses show those of the SP1-150VC.*The dimensions in square brackets show those of the SP05-150VC.


45

Single-Acting Cylinders/Double-Acting Cylder


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs ■SW05-40L (R) VC ■SW01-30L (R) VC/SW03-35L (R) VC ■SW01-30VC

■SpecificationsModel SW01-30L SW01-30R SW03-35L SW03-35R SW05-40L SW05-40R

Rotation direction — 90° counter-clockwise 90° clockwise 90° counter-

clockwise 90° clockwise 90° counter-clockwise 90° clockwise

Stroke

Swing mm 24 28 30Vertical descent

mm 6 7 10

Total mm 30 35 40Maximum overall length A 187 237.5 278Cylinder external diameter ϕ C 48 70.5 100Piston diameter ϕ D 28 35.5 50Arm screw size J M10 x 1.5 M16 x 2 M20 x 2.5Effective arm length K 55 70 100Arm width L 28 38 70Collar thread size M M48 x 1.5 M70 x 2 M100 x 2Collar thread length N 56 81 90Maximum arm length R 83 114 165Straight section Q 15 22 20Coupler protrusion length

VC-70-R3V

≈ 46 ≈ 46 ≈ 46S-1R ≈ 53 ≈ 53 ≈ 53ROC-13R ≈ 49 ≈ 49 ≈ 49

Port position W 95 127 138Boss length X 19 20 —Required oil volume cm3 4 16 35Approx. weight kg 2.1 5.4 13.6

●The arm of a swing cylinder turns 90° lowering down and then lowers vertically a few millimeters to be used for clamping, etc. ●Two types are available: the R type for right rotation (the arm rotates clockwise viewed from the top) and the type for left rotation (the

arm rotates counterclockwise viewed from the top).●The arm can be positioned to any position against the port. ●If the arm length is changed, reduce the working pressure corresponding to the length extended from the standard length.*The SW-05 does not include nuts and bolts for the arm.

SW01 SW03 SW05Maximum operating pressure 40 MPa

Maximum output 4.6 kN 17.6 kN 34.5 kN

Effective area 1.15 cm2 4.42 cm2 8.63 cm2

Cylinder system Single-acting Double-acting

Return system Spring-return Hydraulic-returnCoupler connection port size Rc3/8

4.6 to 34.5 kN Swing Cylinders (SW Series) Maximum operating pressure: 40 MPa


SW 01 - 30 L VCStroke Attached coupler

Maximum output (mm) VC : VC-70-R301 : 4.6 kN S : S-1R03 : 17.6 kN T : ROC-13R05 : 34.5 kN Rotation direction -NC : W/O coupler

Swing cylinder R : Clockwise rotation (viewed from the top)SW series L : Counterclockwise rotation (viewed from the top)

Clamping must be done during vertical descent. While the arm is turning, clamping may cause a cylinder failure.


46


ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■SpecificationsModel BRS-1-10-NC BR-1-10-NC BRS-2-20-NC BR-2-20-NC BRS-4-20-NC BR-4-20-NC BR-4-20D-NC

Maximum output kN 10 20 40Effective area cm2 1.53 3.14 6.42 6.81Stroke mm 10 20 20Minimum overall length A 87 97 90 107Cylinder internal diameter ϕ 14 20 28.6 38Cylinder external diameter ϕ C 30.5 55 33 60 39 60 70Piston diameter ϕ D 12 16 25Piston thread size E M12 x 1.5 M16 x 1.5 M18 x 1.5 —Largest bore length F — 36 — 40 — 45 30Piston protrusion length H 10 16 10 2Wrench catcher (width across flats) R 22 — 22 — 25 — —Collar thread size M M33 x 2 M36 x 2 M42 x 2 M52 x 2Collar thread length N 65 15 70 15 65 15 20Coupler position T — 22 — 25 — 25 35Required oil volume cm3 2 7 13 14Approx. weight kg 0.4 0.8 0.5 1.1 0.7 1.3 1.7


Maximum output 10/20/40 kN



Coupler connection port size Rc3/8*No coupler is attached to the BR and BRS series. *The center hole diameter of the BR-4-20D is ϕ 18.5.

■SpecificationsModel W-01

Maximum operating pressure MPa 70Maximum output (tip) kN 10Maximum output (base) kN 40Effective area cm2 6.42


VC-70-R3S

≈ 46S-1R ≈ 53ROC-13R ≈ 49

Coupler connection port size — Rc3/8Cylinder system — Single-actingReturn system — Spring-returnRequired oil volume cm3 10Approx. weight kg 2.4

10 to 40 kN Mini-Cylinders (BR/BRS Series)

Wedge Ram (W Series)


BR - 1 - 10 -NCMaximum output -NC : W/O coupler

1 : 10 kNMini-cylinder 2 : 20 kN

BR series 4 : 40 kN Stroke (mm)BRS series


W - 01 VCMaximum output Attached coupler

Single-acting cylinder 1 : 10 kN VC : VC-70-R3W series (tip) S : S-1R

T : ROC-13R-NC : W/O coupler

■BRS-1-10-NC ■BRS-2-20-NC ■BRS-4-20-NC

■BR-4-20D-NC ■BR-1-10-NC ■BR-2-20-NC ■BR-4-20-NC

■W-01VC

■W-01VC


47



Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■SpecificationsModel SRP-05 SRP-1 SRP-5 SRP-10 SRP-20

Maximum output torque 0.5 kN • m 1 kN • m 5 kN • m 10 kN • m 20 kN • mTheoretical pressure 25.0 MPa 20.5 MPa 22.0 MPa 25.4 MPa 28.6 MPa

Rotation angle ARequired oil volume

cm3

Approx. weight

kgA

Required oil volume

cm3

Approx. weight

kgA

Required oil volume

cm3

Approx. weight

kgA

Required oil volume

cm3

Approx. weight

kgA

Required oil volume

cm3

Approx. weight

kg

90° 220 32 12.5 278 76 37.0 478 352 79 497 609 117 688 1082 213180° 296 63 13.5 382 150 38.5 690 704 85 667 1218 127 990 2164 225360° 446 124 15.0 590 300 41.5 1114 1407 97 1007 2436 150 1593 4320 249

*Set the operating torque to 80 % of the maximum one or less.

Model B C D E F G H J K L ϕ M N P Q ϕ R ☆ Mounting thread

SRP-05 180.5 122 123 90 61 45 45 10 46 7 30 33 117 93 55 2.5 3 x (4 x M10 DP15)

SRP-1 230.5 172 160 120 75 67 57 12 60 10 45 48 146 117 70 4 3 x (4 x M12 DP25)

SRP-5 337.5 232 254 180 116 86 86 20 105 15 70 74.5 204 160 104 9 3 x (4 x M16 DP25)

SRP-10 421.5 260 262 170 110 120 80 20 145 15 80 84.5 238 193 155 12 3 x (4 x M18 DP30)

SRP-20 526.5 304 349 244 156 126 126 28 220 10 110 116 282 222 155 20 3 x (4 x M24 DP40)

☆ mark: Maximum allowable radial load at the center of the shaft (unit: kN)

*For the VC-70-R3, S-1R, and ROC-13R, the coupler protrusion lengths are about 46 mm, 53 mm, and 49 mm, respectively. *Connect a drain pipe to the gear case. *The external drawings show the key position of the standard product, at which the ram rotates to both right and left by half the rated angle. *Make to order is possible if the key position needs to be changed or angles other than the above are required. *When oil is fed to the right port, the shaft rotates counterclockwise. When oil is fed to the left port, the shaft rotates clockwise. *Do not carry out a securing method that applies a thrust load to the shaft. * When the equipment is self-propelled due to changes in moment, install a valve (counterbalance valve) to prevent the equipment from being self-propelled in the circuit.

*The backlash between the pinion and rack of the rotation ram is between 0.5 and 1°.

● An oscillating-type actuator that rotates the pinion using a rack with pistons at both ends to generate strong torque at the shaft, resulting in almost no heat and noise.Maximum operating pressure 30 MPaMaximum output torque 0.5/1/5/10/20 kN • mCylinder system Double-actingCoupler connection port size Rc3/8

0.5 to 20 kN·m Rotation Ram (SRP Series) Maximum operating pressure: 30 MPa • Make-to-order product


SRP - 1 - 90 VCMaximum torque Rotation angle Attached coupler05 : 0.5 kN • m 90 : 90° VC : VC-70-R31 : 1 kN • m 180 : 180° S : S-1R5 : 5 kN • m 360 : 360° T : ROC-13R

10 : 10 kN • m -NC : W/O couplerRotation ram 20 : 20 kN • m

SRP series

■All SRP series models

■Hydraulic symbol

■SRP-1-90S


48

Cylinder PartsH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■R-20SP ■R-1020SP ■R-10SP

■R-70P to R-500P ■R-4P to R-50P ■R-10PM

■SpecificationsModel A B C ϕ D F G Approx. weight (kg)

For 40 kN R-4P 3/4-14NPT 20 32 35 — — 0.2

For 50 kN R-5PM M20 x 1.5 24 36 37 ϕ 6 DP5 — 0.3

For 100 kN R-10PM M28 x 2 31 43 47 ϕ 6 DP5 — 0.5

R-10P 1 1/4-11.5NPT 25 38 50 — — 0.35

For 200 kN R-20PM M40 x 2 39 52 58 ϕ 6 DP5 — 0.7

R-20P 2-11.5NPT 27 40 76 — — 0.8

For 300 kN R-30P M65 x 2 30 50 90 — — 1.7

For 350 kN R-35P M50 x 2 43 58 70 — — 1.1

For 400 kN R-40P M70 x 2 30 50 99 — — 2.0

For 500 kN R-50P M92 x 2.5 25 46.5 117 — — 2.6

For 700 kN R-70P M90 x 2 30 52 120 3 x ϕ 8 DP10 M8 2.9

For 1000 kN R-100P M90 x 3 55 80 125 4 x ϕ 10 DP10 M10 4.7

For 2000 kN R-200P M120 x 4 60 85 160 4 x ϕ 10 DP10 M16 7.9

For 3000 kN R-300P M150 x 3 70 100 190 4 x ϕ 12 DP13 M20 12.5

For 5000 kN R-500P M180 x 4 70 100 230 4 x ϕ 15 DP18 M24 18.6

■SpecificationsModel A B ϕ C D E Approx. weight (kg)

For MS/MD100 kN R-10SP M28 x 2 65 58 31 ϕ 6 DP5 0.9

200 kN R-20SP M40 x 2 73 58 39 ϕ 6 DP5 1.0

ForMC/MR1R1/RJ1

100 kNR-1020SP ϕ 19 45 32 — — 0.2

200 kN

● Suitable for when a load is applied to the piston.

● This is for the MS, MD, and MC series of 100 and 200kN, and for the MR1, R1, and RJ1 series. ● Suitable for when an eccentric load is applied. ● The maximum angle of oscillation is 5°.

Caps

Tilt Saddles

Cap

Tilt saddle

The load must be received at the center of the cap so that the load is not eccentric. An eccentric load may overturn or damage the cylinder.

The load must be received at the center of the cap so that the load is not eccentric. An eccentric load may overturn or damage the cylinder.


49

Cylinder Parts


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■Specifications

Model A ϕ B C ϕ D E ϕ F ϕ G H IBolt size

Approx. weightkg

For 40 kN 4FS 1 1/2-16NS

145 25 80 20 110 2 x 13.5 10 ϕ 10 DP40 M8 threaded THRU M122.5

4FD M45 x 1.5 2.4

For 50 kN 5FM M45 x 1.5 145 23 80 18 110 2 x 13.5 8 ϕ 10 DP40 M8 threaded THRU M12 2.2

For 100 kN 10FM M58 x 2

145 25 80 20 110 4 x 13.5 10 ϕ 10 DP30 M8 threaded THRU M12 2.210F 2 1/4-14NS

For 200 kN 20FM M82 x 2

195 50 116 30 150 4 x 18 40 M8 M166.5

20F 3 5/16-12NS 6.3

For 300 kN 30F M100 x 2 208 55 125 30 170 6 x 18 45 M10 M16 6.7

For 350 kN 35F M110 x 2.5 218 55 135 32 180 6 x 18 45 M10 M16 7.5

For 500 kN 50F M127 x 2.5 258 55 160 35 210 6 x 22 45 M10 M20 11.4

For 1000 kN 100F M170 x 3

328 65 215 45 270 8 x 26 55 M10 M2422.5

100FB* M185 x 3 20.3

For 2000 kN 200F M240 x 4

458 73 310 55 390 12 x 32 40ϕ 13 DP80 M12 threaded THRU

M3051.7

200FB* M255 x 4 ϕ 13 DP75 M12 threaded THRU 48.3

For 3000 kN 300F M315 x 4 558 89 390 65 480 12 x 38 45 ϕ 13 DP95 M12 threaded THRU M36 85.8

For 5000 kN 500F M410 x 6 678 97 510 80 600 18 x 38 50 ϕ 13 DP110 M12 threaded THRU M36 140.6

*The 100FB and 200FB are exclusively for use with the D10-500 and D20-1000, respectively.

■SpecificationsModel A ϕ B C ϕ D E F G H Approx. weight kg

For 40 kN RB-4 3/4-14NPT 106 25 45 15 20 5 M6 1.1

For 50 kN RB-5M M20 x 1.5 108 32 40 15 24 10 M8 1.2

For 100 kNRB-10M M28 x 2

13843 48

2031 10 M8 2.5

RB-10 1 1/4-11.5NPT 30 58 25 5 M6 2.3

For 200 kN RB-20M M40 x 2 168 54 65

2639 10 M8 4.9

RB-20 2-11.5NPT 165 34 85 27 17 ϕ 10 DP40 M8 threaded THRU 4.1

For 300 kN RB-30 M65 x 2 178 45 90 25 30 10 M8 5.1

For 350 kN RB-35 M50 x 2 198 70 100 45 47 15 ϕ 10 DP10 M8 threaded THRU 11.7


For 500 kN RB-50 M92 x 2.5 228 50 150 30 26 10 ϕ 10 DP15 M8 threaded THRU 14.0


● Suitable for when a load is applied to the piston or when a jig or the like is attached.

●Compatible with collar threads of cylinders. Suitable for securing a cylinder.

Piston Bases

Flanges

■RB-20 ■RB-4 to RB-20M/RB-30 to RB-100 ■RB-10M

■20FM to 100FB ■4FS to 10F/200F to 500F ■10FM

Piston base

Flange

Secure the flange so that the bolts must not receive the load from the cylinder. Otherwise,the bolts may be broken off causing the eqipment to fall.

The load must be received at the center of the piston base so that the load is not eccentric.An eccentric load may overturn or damage the cylinder.


50

Cylinder PartsH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■CB ■CB-10M

■SpecificationsModel A ϕ B C D E F ϕ G Approx. weight (kg)

For 40 kN CB-4 3/4-14NPT 106 38 18 20 20 — 1.5For 50 kN CB-5M M20 x 1.5 108 43 23 19 20 46 1.4

For 100 kN CB-10M M28 x 2 138 50 30 19 20 58 2.4CB-10 1 1/4-11.5NPT 138 42 20 20 22 58 2.6

For 200 kN CB-20M M40 x 2 168 63 38 24 25 82 4.6CB-20 2-11.5NPT 165 50 22 26 28 86 4.9

For 300 kN CB-30 M65 x 2 178 53 28 24 25 102 5.2For 350 kN CB-35 M50 x 2 198 62 34 27 28 110 7.1For 400 kN CB-40 M70 x 2 208 57 29 27 28 117 8.3For 500 kN CB-50 M55 x 3 228 84 54 29 30 128 10.3

■SpecificationsModel A B ϕ C D Approx. weight (kg)

For 40 kN CBP-4 3/4-14NPT 20.5 18 2 x ϕ 3.5 DP8 0.1For 50 kN CBP-5M M20 x 1.5 23.5 12 2 x ϕ 3.5 DP4 0.1

For 100 kN CBP-10M M28 x 2 29.5 18 2 x ϕ 4.5 DP5 0.1CBP-10 1 1/4-11.5NPT 24.5 32 2 x ϕ 4.5 DP8 0.3

For 200 kN CBP-20M M40 x 2 38.5 28 2 x ϕ 6 DP6 0.3CBP-20 2-11.5NPT 26.5 48 2 x ϕ 6 DP8 0.6

For 300 kN CBP-30 M65 x 2 29.5 48 2 x ϕ 6 DP8 0.8For 350 kN CBP-35 M50 x 2 34.5 38 2 x ϕ 4.5 0.5For 400 kN CBP-40 M70 x 2 29.5 58 2 x ϕ 6 DP8 0.9For 500 kN CBP-50 M55 x 3 54.5 38 2 x ϕ 4.5 DP8 1

● Suitable for stabilizing a cylinder having a base thread.

● Suitable for protecting the base thread.

■TH-110 to TH-170 (handle type)

■TH-185 to TH-315 (lifting handle type)

■CBP

■Specifications

Model Compatible cylinder A ϕ B C D Approx. weight kg

TH-110 DC2-100/DC2-200 M110 x 2 130 254 30 1.8

TH-127

S5-50/S5-53/S5-100/S5-153

M127 x 2.5 150 282 35 1.9D5-50/D5-100/D5-150D5-300/D5-500DC3-100/DC3-200

TH-135 DC4-100/DC4-200 M135 x 3 160 296 35 2.2TH-165 DC5-100/DC5-200 M165 x 3 190 314 40 2.9TH-170 D10-50/D10-150/D10-300 M170 x 3 195 320 55 3.9

Model Compatible cylinder A ϕ B C D Approx. weight kg

TH-185 D10-500/DC7-150 M185 x 3 210 310 50 3.6TH-230 DC10-150 M230 x 3 255 375 60 5.1

TH-240D20-150/D20-300

M240 x 4 265 385 60 5.5D20-500

TH-255 D20-1000 M255 x 4 280 400 60 5.8

TH-315D30-300/D30-500

M315 x 4 345 465 60 8.4D30-850/DC20-150

● Lifting handles that are screwed to the collar thread of a cylinder.

Cylinder Lifting Handles Make-to-order product

Cylinder Bases

Plugs for Base Treads

Cylinder base

The load must be received at the center of the cylinder base so that the load is not eccentric. An eccentric load may overturn or damage the cylinder.


51

Cylinder Parts


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■Male clevis (female thread) ■Male clevis (male thread) ■CLF-10-1 ■CLM-10-1

■Specifications (for male clevises with female thread)

Model A ϕ B C D (tolerance) E F G H ϕ J (tolerance) LApprox. weight

kg

For 40 kN CLF-4-A 77.545 41 16

0to

-0.2M8

3/4-14NPT 21 57 16 +0.1to

+0.323 0.5

For 50 kN CLF-5-1 74.5 M20 x 1.5 22 54 18

For 100 kN CLF-10-A

97.5 57 55 200to

-0.2M8

1 1/4-11.5NPT 2670 25

+0.1to

+0.330 0.9

CLF-10-1 M28 x 2 30

For 200 kN CLF-20-A

125 86 80 300to

-0.2M8

2-11.5NPT 2785 36

+0.1to

+0.340 2.5

CLF-20-1 M40 x 2 35

For 350 kN CLF-35-1 198 110 110 480to

-0.2M10 M50 x 2 46 143 48

+0.1to

+0.355 8.8

For 500 kN CLF-50-1 235 128 128 570to

-0.2M10 M55 x 3 51 171 57

+0.1to

+0.364 14.5

■Specifications (for male clevises with male thread)

Model A ϕ B C D (tolerance) E F G H ϕ J (tolerance) LApprox. weight

kg

For 40 kN CLM-4-A 74.545 41 16

0to

-0.2M5

3/4-14NPT18

54 16 +0.1to

+0.323 0.4

For 50 kN CLM-5-1 75.5 M20 x 1.5 55 18

For 100 kN CLM-10-A 96.5

57 55 200to

-0.2M5

1 1/4-11.5NPT 24 6925

+0.1to

+0.330 0.9

CLM-10-1 98.5 M28 x 2 23 71

For 200 kN CLM-20-A 122

86 80 300to

-0.2M6

2-11.5NPT25

8236

+0.1to

+0.340 2.3

CLM-20-1 127 M40 x 2 87

For 350 kN CLM-35-1 198 110 110 480to

-0.2M10 M50 x 2 33 143 48

+0.1to

+0.355 7.7

For 500 kN CLM-50-1 237 128 128 570to

-0.2M10 M55 x 3 53 173 57

+0.1to

+0.364 11.1

Male Clevis (Female Thread/Male Thread)


CLF - 4 - A1 : Male clevis (for metric threaded cylinders)

4 : 40 kN 2 : Female clevis (for metric threaded cylinders)Clevis 5 : 50 kN A : Male clevis (for unified threaded cylinders)

CLF : Female thread 10 : 100 kN B : Female clevis (for unified threaded cylinders) CLM : Male thread 20 : 200 kN

35 : 350 kN50 : 500 kN


CLP - 44 : 40 kN5 : 50 kN

CLP : Pin 10 : 100 kN CLW : Washer 20 : 200 kN CLC : Split pin 35 : 350 kN

50 : 500 kN

*Two washers and two split pins are needed per clevis pin.

The clevis must be used with a half of the indicated load or smaller to pull an object. Otherwise, the equipment may bedamaged or scattered matter may cause injury.


52

Cylinder PartsH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■Pin Model A ϕ B (tolerance) C ϕ DFor 40 kN CLP-4

5816 0

50 2For 50 kN CLP-5 18 - 0.04

For 100 kN CLP-10 70 250

60 3.2- 0.05

For 200 kN CLP-20 100 360

88 5- 0.06

For 350 kN CLP-35 152 480

137 5- 0.2

For 500 kN CLP-50 174 570

158 6.3- 0.2

Model A ϕ B 40 kN CLC-4 25 1.8 50 kN CLC-5 25 1.8100 kN CLC-10 36 2.9200 kN CLC-20 50 4.6350 kN CLC-35 70 4.6500 kN CLC-50 80 5.9

Model ϕ A ϕ B C 40 kN CLW-4 28 17 3 50 kN CLW-5 30 19 3100 kN CLW-10 39 27 3200 kN CLW-20 60 37 5350 kN CLW-35 92 50 8500 kN CLW-50 105 58 9

*Two washers and two split pins are needed per clevis pin.

■Specifications (for female clevises with female thread)

Model A ϕ B C D (tolerance) E F G H ϕ J (tolerance) K LApprox. weight

kgFor 40 kN CLF-4-B

73 45 38 16+0.2

to+0.5

M83/4-14NPT 21

5416 +0.1

to+0.3

40 24 0.5For 50 kN CLF-5-2 M20 x 1.5 22 18

For 100 kN CLF-10-B

96 57 52 20+0.2

to+0.5

M81 1/4-11.5NPT 26

70 25+0.1

to+0.3

46 33 0.9CLF-10-2 M28 x 2 30

For 200 kN CLF-20-B

119 86 76 30+0.2

to +0.5

M82-11.5NPT 27

85 36+0.1

to+0.3

70 45 2.5CLF-20-2 M40 x 2 35

For 350 kN CLF-35-2 185 110 104 48+0.2

to+0.5

M10 M50 x 2 46 133 48+0.1

to+0.3

110 60 9.1

For 500 kN CLF-50-2 220 128 122 57+0.2

to+0.5

M10 M55 x 3 51 159 57+0.1

to+0.3

128 68 14.7

■Specifications (for female clevises with male thread)

Model A ϕ B C D (tolerance) E F G H ϕ J (tolerance) K LApprox. weight

kg

For 40 kN CLM-4-B 7045 38 16

+0.2to

+0.5M5

3/4-14NPT18

51 16 +0.1to

+0.340 24 0.4

For 50 kN CLM-5-2 74 M20 x 1.5 55 18

For 100 kN CLM-10-B 95

57 52 20+0.2to

+0.5M5

1 1/4-11.5NPT 24 69 25 +0.1to

+0.346 33 0.9

CLM-10-2 97 M28 x 2 23 71 25

For 200 kN CLM-20-B 116

86 76 30+0.2to

+0.5M6

2-11.5NPT25

82 36 +0.1to

+0.370 45 2.4

CLM-20-2 121 M40 x 2 87 36

For 350 kN CLM-35-2 185 110 104 48+0.2to

+0.5M10 M50 x 2 33 133 48

+0.1to

+0.3110 60 8

For 500 kN CLM-50-2 222 128 122 57+0.2to

+0.5M10 M55 x 3 53 161 57

+0.1to

+0.3128 68 11.3

■Split pin ■Washer

Female Clevis (Female Thread/Male Thread)

Clevis Pins

Clevis Washers/Split Pins

■Female clevis (female thread) ■Female clevis (male thread) ■CLF-10-2 ■CLM-10-2


53

Cylinder Parts


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

● By using attachments, a small eccentric load could become big moment applied to the cylinder, which may overturn or damage the cylinder. Taking into consideration the allowable eccentric load to the cylinder, use a guide if needed.

● Depending on the combination of attachments, the cylinder may not be used at the maximum operating pressure.

● Do not use two or more connected pipes with female joints.

■100 kN attachments For piston threads and pipes

R-103 (Four-legged cap) R-105 (Triangle cap) R-106 (Cylinder flat base)

Approx. weight: 0.9 kg Approx. weight: 0.8 kg Approx. weight: 1.9 kgFor piston threads and pipes For collar threads For base threads

R-107 (Collar toe) *Be careful of an eccentric load. R-306 (Threaded connector) R-116 (Male joint)

Approx. weight: 0.9 kg Approx. weight: 1.2 kg Approx. weight: 0.4 kgFor piston threads and pipes Pipe PipeR-117 (Female joint) *Note R-113/R-114 R-115/R-311

Approx. weight: 0.5 kg Approx. weight: R-113: 0.5 kg R-114: 1.1 kg Approx. weight: R-115: 2.2 kg R-311: 3.3 kg

●Used for mounting an attachment to the piston thread of MS and MD series cylinders.*No attachments can be mounted to the collar and base threads of MS and MD series cylinders.

Model A B C Approx. weight (kg)

For 100 kN MI-10 1 1/4-11.5NPT M28 x 2 37 0.2

For 200 kN MI-20 2-11.5NPT M40 x 2 45 0.5

■For 100 kN ■For 200 kN

100 and 200 kN Attachments for Unified Threaded Cylinders

Thread Caps for 100 and 200 kN Attachments (Metric-to-Unified Thread Conversion Bushing)

*The dimensions in parentheses show those of the R-114.

■200 kN attachments R-202 (Female joint) *Note R-205 (Collar toe) R-206/R-207/R-208/R-215 (Pipe)

Approx. weight: 1.7kg Approx. weight: 3.4kg

A Approx. weight (kg)

R-206 250 3.0R-207 500 6.1R-208 750 9.3R-215 125 1.5

*The dimensions in parentheses show those of the R-311.

Examples of Attachment Combinations

● Attachments suitable for each work are mounted using the piston thread,collar thread,and/or base thread of the cylider.● Only those to be mounted to the piston thread can be used in MS and MD series cylinders by using the following thread caps.

Piston thread

Collar thread

*Be careful of an eccentric load.

Base thread


54

DataH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


● The cylinder and pump selection table shown below is based on the oil volume required for one cylinder.● A pump with a large tank capacity may be required depending on the piping length. ● Valves or other equipment may be required depending on the usage. * The table below is just a selection guide. Take into consideration the frequency of lever operation for manual pumps and the cylinder speed (see page 226) for electric pumps.

* See pages 7, 8, and 12 for selecting pumps and cylinders. * If a single-acting cylinder is operated by the MP-10C, 12C, or 15C, additional parts may be required.

■Single-acting cylindersMaximum output 50 kN 100 kN 200 kN 300 kN 500 kN 700 kN

Stroke (mm)

Model

50100150

50100150

200250300

75100150

200300500

50125200

2550

100153

2550

100

Man

ual P

umps

P-1B ○ ○ ○ ○ X ○ X ○ X X

P-4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○P-8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○P-5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○P-7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Ele

ctric

Pum

ps

SMP-30/40 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○EMP-5B ○ ○ ○ ○ ○ ○ ○ ○ ○ ○MP-4B ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

EMP-6B ○ ○ ○ ○ ○ ○ ○ ○ ○ ○MP-10C X ○ ○ ○ ○ ○ ○ ○ ○ ○MP-12C X ○ ○ ○ ○ ○ ○ ○ ○ ○MP-15C X X ○ ○ ○ ○ ○ ○ ○ ○

■Double-acting cylinders

Maximum output 50 kN 100 kN 200 kN 350 kN 500 kN 1000 kN2000 kN

Stroke (mm)

Model

50100150

50100150

200250300

50100150

200300500

100150300

50100150

300500

50150

3001000

150300500

Man

ual P

umps

P-1D ○ ○ ○ ○ X X X X X X X X

P-4D ○ ○ ○ ○ ○ ○ X X X X X X

P-8D ○ ○ ○ ○ ○ ○ ○ ○ X X X X

P-5D ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X X

P-7C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X X

Ele

ctric

Pum

ps

SMP-30C/40C ○ ○ ○ ○ ○ ○ ○ ○ X X X X

EMP-5C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X X

MP-4C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X X

EMP-6C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X X

MP-10C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○MP-12C ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○MP-15C X X X ○ ○ ○ ○ ○ ○ ○ ○ ○MP-17C X X X ○ ○ ○ ○ ○ ○ ○ ○ ○MP-20C X X X X X X X ○ ○ ○ ○ ○

Cylinder and Pump Selections


55

Data


Hyd

raul

ic C

ylin

ders

Dat

aC

ylin

der p

arts

Spe

cial

Cyl

inde

rsDo

uble-

Actin

g Cylin

ders

Single

-Acti

ng C

ylinde

rs

■MS1-150VC

■MC1-35VC

■S1-150S

■R1-63S

No Part name Qty. MC1-35VC R1-63S

11 Cylinder tube 1 ○ ○12 Piston 1 ○ ○14 Piston stop ring 1 ○ ○16 Thread cover 1 ○ ○17 Head cover 1 ○ ○29 Spring 1 ○ —

33 Spring 1 ○ ○34 Spacer 1 ○ —

61 O-ring 1 ○ ○71 Backup ring 1 ○ ○88 Steel ball 1 ○ ○91 Coupler 1 VC-70-R3 S-1R

96 Set screw 1 ○ ○*The structure and parts differ depending on the model. *Please contact us for internal drawings of other models.

No Part name Qty. MS1-150VC S1-150S

11 Cylinder tube 1 ○ ○12 Piston 1 ○ ○13 Bottom cap 1 ○ ○14 Piston stop ring 1 ○ ○15 Thread cap 1 — ○16 Thread cover 1 ○ ○21 Spring bracket 1 ○ ○23 Spring hanging bolt 1 ○ ○24 Spring hook bolt 1 ○ ○25 Cap nut 1 ○ ○26 Washer 1 ○ ○29 Spring 1 ○ ○61 O-ring 1 ○ ○62 O-ring 1 ○ ○71 Backup ring 1 ○ ○72 Backup ring 1 ○ ○91 Coupler 1 VC-70-R3 S-1R

96 Set screw 1 ○ ○*The structures and parts differ depending on the model. *Please contact us for internal drawings of other models.

■Single-acting short cylinders40 to 700 kN short cylinders (spring-return type, MC/S series)40 to 1000 kN short cylinders (load-return type, MR/R series)

■Single-acting cylinders (spring-return type) 40 to 700 kN spring-return type (MS/S series)

Cylinder Structural Drawings

The dotted red line represents a packing set: PMS-10.





56

DataH

ydraulic Cylinders


Special C

ylindersC

ylinder partsD

ata


■D5-300C

The dotted red line represents a packing set: PMD-50.

■DC3-100S

■Double-acting cylinders40 to 5000 kN (MD/D series)

■Double-acting center hole cylinder 200 to 2000 kN (DC series)

No Part name Qty.

11 Cylinder tube 1

12 Piston 1

13 Bottom cap 1

14 Piston stop ring 1

15 Thread cap 1

16 Thread cover 1

61 O-ring 3

64 Penta seal 1

71 Backup ring 2

72 Backup ring 2

74 Backup ring 1

81 Dust seal 1

83 Hexagon socket set screw 2

91 Coupler (S-24R) 2


97 Rotation preventing spacer 2*The structure and parts differ depending on the model. Please contact us for internal drawings of other models.

*The structure and parts differ depending on the model. Please contact us for internal drawings of other models.

No Part name Qty.

11 Cylinder tube 1

12 Piston 1

14 Piston stop ring 1

20 Core bar 1

61 O-ring 2

64 O-ring 1

65 O-ring 2

71 Backup ring 2

73 Backup ring 1

74 Backup ring 1

75 Backup ring 2

81 Dust seal 1

91 Coupler (S-1R) 2


Cylinder Structural Drawings


hydraulic cylinders - breedveld-weaver.nl · [strong type] under no load condition: 1000 mm/s max....

Documents