hydraulic turbines

29
HYDRAULIC TURBINES

Upload: nikhilesh-mane

Post on 11-Apr-2017

421 views

Category:

Engineering


1 download

TRANSCRIPT

Page 1: Hydraulic turbines

HYDRAULIC TURBINES

Page 2: Hydraulic turbines

CONTENT

1] DEFINATION OF HYDRAULIC TURBINE2] CLASIFICATION3] TYPES 3.1] Pelton turbine 3.2] Kaplan turbine 3.3] Francis turbine4] DIFFERENCE BETWEEN PELTON , KAPLAN , FRANCIS TURBINES.

Page 3: Hydraulic turbines

INTRODUCTION • A water turbine is a rotary machine that converts kinetic

energy and potential energy of water into mechanical work and rotates the shaft to produce electric energy.

Basic working principle:- Hydraulic turbine converts the potential energy of water into mechanical work.

Page 4: Hydraulic turbines

CLASSIFICATION• Based on head

a) High head turbinesb) Medium head turbinesc) Low head turbines

• Based on hydraulic action of water a) Impulse turbines

b) Reaction turbines• Based on direction of flow of water in the runner

a) Tangential flow turbinesb) Radial flow turbinesc) Axial flow turbinesd) Mixed flow turbines

Page 5: Hydraulic turbines

Three most popular turbines are

• PELTON WHEEL { PELTON TURBINE}• KAPLAN TURBINE {PROPELLER TURBINE}• FRANCIS TURBINE

Page 6: Hydraulic turbines

PELTON WHEEL The Pelton wheel is an impulse type water

turbine. It was invented by Lester Allan Pelton in the 1870s.

This turbine is used for high heads

Page 7: Hydraulic turbines

SPECIFICATION• Power generation is about 400MW.• The speed rate ranges from 65 to 800rpm.• The efficiency is about 85%.• The runner diameters is between 0.8 t0 6.0m.• The operational head is from 15 to 1800m.

Page 8: Hydraulic turbines

MAIN COMPONENTS1] Nozzle and spear2] Runner and bucket 3] Casing4] Breaking jet

1] Nozzle :- It controls the amount of water striking the vanes of runner.

2] Casing :- It is used to prevent splashing of water.

Page 9: Hydraulic turbines

3] Runner and Bucket :- It is circular disc on the periphery on which evenly spaced bucket are fixed.4] Breaking jet :- Its function is to stop the runner in a short time period.

Page 10: Hydraulic turbines

WORKING 1. The flow of water is tangential to the runner. So it is a tangential flow impulse turbine.2. The runner consists of a single wheel mounted on a horizontal shaft.3. Water falls towards the turbine through a pipe called penstock and flows through a nozzle.4. The high speed jet of water hits the buckets (vanes) on the wheel and causes the wheel to rotate.5. A spear rod which has a spear shaped end can be moved by a hand wheel.

6. This movement controls the flow of water leaving the nozzle before it strikes the bucket.

Page 11: Hydraulic turbines

7. The bucket or vane is so shaped that when the water strikes, it gets split into two and gives it an impulse force in the center of the bucket. This bucket is also known as splitter.

Page 12: Hydraulic turbines
Page 13: Hydraulic turbines

SR NO. STATION POWER GENERATED[MW]

1 AMBALA CANTT[INDIA] 800

2 BIEUDRON[SWISS] 1269

3 CASTAIC [US] 1500

Page 14: Hydraulic turbines

KAPLAN TURBINE• The Kaplan turbine is a propeller-type water

turbine which has adjustable blades. It was developed in 1913 by Austrian professor Viktor Kaplan.

• It is mainly used for low-head applications.

Page 15: Hydraulic turbines

SPECIFICATIONS• The head ranges from 10–70 metres• The output varies from 5 to 200 MW.• Runner diameters are between 2 and 11 metres.• The rotational speed rate ranges from 69.2 rpm

to 429 rpm• It gives highest efficiency which is over 90%.

Page 16: Hydraulic turbines

THE MAIN COMPONENTS ARE :-

1] Scroll casing2] Guide vanes 3] Draft tube4] Runner 5] Hub

1] Scroll casing: It is the casing which guides the water and control the water passage. 2] Guide vanes : It is the vanes which guide the water and perform same function that by scroll.

Page 17: Hydraulic turbines

3] Draft tube:- It discharges the water to trail race through gradually expanding tube.4] Runner :- It is connected to shaft of the generator.5] Hub:- It part on which runner is mounted

Page 18: Hydraulic turbines

WORKING• The water from the penstocks enters the scroll casing and then

moves to the guide vanes. • From the guide vanes, the water turns through 90° and flows

axially through the runner. • For Kaplan Turbine, the shaft of the turbine is vertical. The lower

end of the shaft is made larger and is called ‘Hub’ or ‘Boss’. • The vanes are fixed on the hub and hence Hub acts as runner for

axial flow turbine.

Water flow in

RunnerWater flow out

Page 19: Hydraulic turbines
Page 20: Hydraulic turbines

APLLICATIONS

• The kaplan turbine is used in Indian. SRNO.

STATION POWER GENERATED [MW]

1. LPH 55

2. KADRA 150

3. KODASSALLI 120

4. ALMATTI 275

Page 21: Hydraulic turbines

FRANCIS TURBINE

• The Francis turbine is an inward-flow reaction turbine that combines radial and axial flow concepts.

• It was developed by James .B. Francis.

Page 22: Hydraulic turbines

SPECIFICATION • They operate in a water head from 40 to 600 m

(130 to 2,000 ft).• The power generated is 800MW.• The speed range of the turbine is from 75 to

1000 rpm.• It give efficiency of about 90%.• The runner diameters are between 0.91 to 10.6 m.

Page 23: Hydraulic turbines

THE MAIN PARTS ARE :-

1] Spiral casing2] Guide vanes3] Runners 4] Draft tube

1] Spiral casing :- It guides the water to the guide vanes and also control the flow. 2] Guide vanes :- They guide the water to runner and get closed on increase in flow.

Page 24: Hydraulic turbines

3] Runner :- They are heart of the turbine and rotate on the impact of flow.4] Draft tube :- It is place from where the water is discharged from the turbine

Page 25: Hydraulic turbines

WORKING • Penstock conveys water from the upstream to the turbine runner.

Spiral Casing constitutes a closed passage whose cross-sectional area gradually decreases along the flow direction; area is maximum at inlet and nearly zero at exit.

• The vanes direct the water on to the runner at an angle appropriate to the design, the motion of them is given by means of hand wheel.

• Runner Blades move due to the driving force on the runner which is due to impulse and reaction effect.

• Draft Tube is gradually expanding tube which discharges water, passing through the runner to the tail race.

Water in

Water out

Page 26: Hydraulic turbines
Page 27: Hydraulic turbines

The Francis turbine are used in places like:-

SR NO . PLACES POWER GENERATION [MW]

1 Koyna IV (India) 250

2 Turkwell (Kenya) 53

3 Karun (Iran) 250

4 Three Gorges (China) 765

Page 28: Hydraulic turbines

DIFFERENCE BETWEEN PELTON,KAPLAN,FRANCIS

PARAMETERS PELTON TURBINE KAPLAN TURBINE FRANCIS TURBINE

TYPE OF TURBINE IMPULSE TYPE PROPELLER TYPPE INWARD FLOW REACTION TYPE

POWER GENRATION [MW]

400 200 800

SPEED RATE[rpm] 65 - 800 70-429 75 -1000

EFFICIENCY[%] 85 80 90

Page 29: Hydraulic turbines

THANK You…

Any query?