hydraulics, inc. fs15 series · 2020. 8. 25. · 6 hydraulics, inc. fs seies motors 1) continuous...

6

Hydraulics, Inc. FS Series Motors

1) Continuous or average working pressure should be chosen on the motor bearing lifetime choice. 2) Speed limitation with optional low speed distributors (eg. D31); see distributor pages section.

FS15 Series 40 48 57 75 90 100 110 130 150 170 200 220 250 Displacement in3/rev 2.46 2.94 3.52 4.70 5.25 6.13 7.05 7.87 9.20 10.15 11.65 13.25 14.37

Torque/100 psi (Theor) ft/lb 3.26 3.90 4.67 6.24 6.96 8.13 9.35 10.45 12.21 13.47 15.46 17.58 19.08

Nominal Pressure(1) psi 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

Peak Pressure psi 5500 5500 5500 5500 5500 5500 5500 5500 5500 5500 5500 5500 5500

Max. speed (2) rpm 2000 1000 1000 1000 1000 1000 1000 900 900 800 700 500 500

Peak power HP 60 60 60 60 60 60 60 60 60 60 60 60 60

FS15 Series HF 40 48 57 75 90 100 110 130 150 170 200 220 250 Displacement in3/rev 2.46 2.94 3.52 4.70 5.25 6.13 7.05 7.87 9.20 10.15 11.65 13.25 14.37

Torque/100 psi (Theor) ft/lb 3.26 3.90 4.67 6.24 6.96 8.13 9.35 10.45 12.21 13.47 15.46 17.58 19.08

Nominal Pressure(1) psi 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

Peak Pressure psi 6000 6000 6000 6000 6000 6000 6000 6000 5800 5800 5800 5800 5800

Max. speed (2) rpm 2000 1700 1600 1500 1350 1100 1200 1100 1100 1000 900 800 700

Peak power HP 90 90 90 90 90 90 90 90 90 90 90 90 90

Approximate Weight: 68 lbs Motor Casing Oil Capacity: 49 in³ Max. Casing Pressure: 14.5 psi (72.5 psi peak)

FS15 SERIES

7

Hydraulics, Inc. FS15 SeriesA1 MOUNT

A2 MOUNT

A3 MOUNT

8

Hydraulics, Inc. FS15 Series

SHAFT OPTIONS FOR A1/A2 MOUNTS1 Piece Shafts

Code 1 Code 3/9 Code 7 Code 8a

Code 28a Code 37 Code 67 Code 68

2 Piece Shafts

Code 13 Code 17 Code 27

9


SHAFT OPTIONS FOR A3 MOUNT WITH 3RD BEARING

Code 17

Code 58 Code 67 Code 68

Code 27 Code 67Code 38Code 32

SHAFT OPTIONS FOR A3 MOUNT WITHOUT 3RD BEARING

Code 26 Code 28

10


SAE-A 2 BOLT FLANGE

SAE-B 2 BOLT FLANGE SAE-B 4 BOLT FLANGE

SAE FLANGE OPTIONS FOR A1 MOUNT

SAE-C 2 BOLT FLANGE SAE-C 4 BOLT FLANGE

11


The graphs indicate the typical performance characteristics of the 250 displacement motor operating with mineral oil with viscosity 40 cSt at 50°C.Sheet3

Page 1

0

100

200

300

400

0 200 400 600 800 1000 1200P

RE

SS

UR

E (p

si)

SPEED (rpm)

IDLING AND BOOST PRESSURE

idling pressure

boost pressure

Sheet2

Page 1

0

5

10

15

20

25

30

0 200 400 600 800 1000 1200

LE

AK

AG

E R

AT

E -

(cu.in/m

in)

SPEED (rpm)

VOLUMETRIC EFFICIENCY

5000 psi

1500 psi

3000 psi

4500 psi

Sheet4

Page 1

0 5 10 15 20 25

TO

RQ

UE

SPEED (rpm)

STARTING AND LOW SPEED TORQUE

93%

92%

90%

87%

6000 psi

4500 psi

3000 psi

1500 psi

SHAFT SPEED (rpm)PISTON Ø (mm)

The graph refers to the motor with roller bearings (option 11). Note that the average lifetime of a bearing (B50 lifetime) is approximately 5 times the B10 lifetime.

BEARING LIFETIME

Motor bearing life on the HD version approx. double than standard version (consult factory for actual hrs life)

150

220

0 200 400 600 800 1000 1200

100

1,000

10,000100,0001,000,000

200

500

2,000

5,000

HOURS

25 30 35 40 45 50 55

170

200

250

4000

2000

1000

3000

5000

90

75 1

10

37 42 48

FS15 MOTORPERFORMANCE DATA

Sheet3

Page 1

0

100

200

300

400

0 200 400 600 800 1000 1200P

RE

SS

UR

E (p

si)

SPEED (rpm)

IDLING AND BOOST PRESSURE

idling pressure

boost pressure

95%

94%

92% 90%

12


1) Mean values at rated conditions. For actual admissible loads based on speed, service life, and application/duty, please consult the Plan-Star PSR catalog.

2) Max. peak values , which must never be exceeded. Combined thrust and radial shaft loads might reduce bearing life. Please contact SAI Engineering for accurate life calculation of your specific application.

3) Combination of high torque and heavy radial shaft load might require verification of the output shaft. If the following condi-tion is not fulfilled, contact SAI engineering for accurate verification of your specific application.

FS15 BEARING CAPACITY GRAPH

13


1. Motor Type FS15 FS15HF

2. Body Type A1 = Flangeless Mount A2 = Flange Mount A3 = SAE-C 2/4 Bolt Mount

3. Nominal Displacement

4. Shaft Options See Shaft Option Section 5. Motor Bearing

13 = Spherical Roller Bearing

6. SAE-C Bearing Option 0 = No Bearing (Standard, No side load allowed) 1 = Ball Bearings (Low side load allowed) 2 = Spherical Roller (Side load allowed, consult factory 7. Shaft Seal E = No Shaft Seal A = High Pressure Seal VY = Viton Shaft Seal I = Case Pressure Relief Valve

8. Distributor Code See Distributor Section

9. Wear Plate DBM = Bronze Wear Plate DGM = Cast Wear Plate

10. Tachometer K= Predisposed for Tach. J = Mechanical Tach. Mount JB2 = Mount for BEI Encoder E25 BA (type 6R) RS = Induction Sensor (20 pulses/rev)

11. Direction of Shaft Rotation No Code = Clockwise (Standard) L = Counter-Clockwise 12. Distributor Cover Position No Code = Position DM1 DM~ = Noted Number Position

FS15 ORDERING CODES

hydraulics, inc. fs15 series · 2020. 8. 25. · 6 hydraulics, inc. fs seies motors 1) continuous...

Documents