i-ds-2250-8 rev 2 - ryadon · 2020. 5. 7. · third angle projection 8±.118" slide travel 8±.020"...
TRANSCRIPT
-
THIRD ANGLE PROJECTION
8±.020" SLIDE LENGTH 8±.118" SLIDE TRAVEL
SCALE: 1:3 SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/27/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-8PART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 8" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3.252±.016
4.252±.016
.622±.008
2.252±.012
1.000±.008 2X .327±.020 X .248±.020 90 INSIDE
3X .220±.020 90 INSIDE
.252±.008
3X .205±.008
.413±.008
.752±.008
.752±.008
1.500±.012
2.000±.012 2.500±.012
3.071±.012
.748±.008
3X .374±.008 X .205±.008
1.252±.012
1.500±.012
.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-8PART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 8" SLIDE
KCHEN 2SCALE: 1:2
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
10±.118" SLIDE TRAVEL 10±.020" SLIDE LENGTH
SCALE: 1:4
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-10-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 10" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2017
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
.252±.008
3.252±.016 6.252±.016
.622±.008
8.504±.020
3X .256±.008
1.000±.008
2X .362±.008 X .276±.008
3X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012
2.000±.012
2.500±.012
.752±.008
5.071±.016
.748±.008
3X .374±.008 X .205±.008.205±.008 X .453±.008
.181±.008 X .205±.008
OBSTRUCTED NON-FUNCTIONAL
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-10-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 10" SLIDE
KCHEN 2SCALE: 1:3
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2017
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
13±.118" SLIDE TRAVEL 12±.020" SLIDE LENGTH
SCALE: 1:4SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-12-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 12" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
.252±.008
3.252±.016
8.252±.020
.622±.008
10.504±.020
3X .256±.008
1.000±.008
2X .362±.008 X .276±.008
3X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012 2.500±.012
.752±.008
7.063±.016
.748±.008
3X .374±.008 X.205±.008
.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-12-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 12" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
15±.118" SLIDE TRAVEL 14±.020" SLIDE LENGTH
SCALE: 1:4SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-14-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 14" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
.252±.008
3.252±.016 10.252±.020
.622±.008
12.504±.020
3X .256±.008
1.000±.008
2X .362±.008 X .276±.008
3X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012
2.000±.012
2.500±.012
.752±.008
9.063±.020
.748±.008
3X .374±.008 X.205±.008
.205±.008 X .453±.008
.181±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-14-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 14" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
17±.118" SLIDE TRAVEL 16±.020" SLIDE LENGTH
SCALE: 1:6SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-16-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 16" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3X .256±.008
.252±.008 1.000±.008 3.252±.016
12.252±.020
.622±.008
14.504±.020
2X .362±.008 X .276±.008
3X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012
2.000±.012
2.500±.012
1.000±.008
.752±.008
11.063±.020
.748±.008
4X .374±.008 X.205±.008
.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-16-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 16" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
19±.118" SLIDE TRAVEL 18±.020" SLIDE LENGTH
SCALE: 1:6
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-18-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 18" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008 3X .256±.008
.252±.008 1.000±.008
3.252±.016 14.252±.020
.622±.008
16.504±.020
2X .362±.008 X .276±.008
4X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012 2.500±.012
5.000±.016
1.000±.008
.752±.008
13.063±.020
.748±.008
4X .374±.008 X.205±.008
.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-18-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 18" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
21±.118" SLIDE TRAVEL 20±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-20-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 20" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2017
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3X .256±.008
.252±.008 1.000±.008
3.252±.016 16.252±.020
.622±.008
18.504±.020
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012
5.000±.016
7.500±.020
1.000±.008
.752±.008
15.063±.020
.748±.008
4X .374±.008 X.205±.008
.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-20-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 20" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2017
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
23±.118" SLIDE TRAVEL 22±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-22-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 22" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3X .256±.008
.252±.008 1.000±.008
3.252±.016 18.252±.020
.622±.008
20.504±.024
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012
5.000±.016 7.500±.020
1.000±.008
.752±.008
17.063±.020
.748±.008
13.563±.020
.181±.008 X .205±.008
.205±.008 X .453±.008
5X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-22-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 22" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
25±.118" SLIDE TRAVEL 24±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-24-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 24" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3X .256±.008
.252±.008 1.000±.008 3.252±.016
20.252±.024
.622±.008
22.504±.024
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012
2.000±.012 2.500±.012
5.000±.016
7.500±.020
1.000±.008
.752±.008
19.063±.020
.748±.008
15.563±.020
.205±.008 X .453±.008
.181±.008 X .205±.0085X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-24-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 24" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
27±.118" SLIDE TRAVEL 26±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-26-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 26" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
3X .256±.008
.252±.008 1.000±.008
3.252±.016 22.252±.024
.622±.008
24.504±.024
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012
5.000±.016
7.500±.020
1.000±.008
.752±.008
21.063±.024
.748±.008
17.563±.020
.181±.008 X .205±.008
.205±.008 X .453±.0085X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-26-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 26" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
29±.118" SLIDE TRAVEL 28±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-28-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 28" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008 4X .256±.008
.252±.008 1.000±.008 3.252±.016
9.752±.020 24.252±.024
.622±.008
26.504±.024
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012 2.500±.012
5.000±.016 7.500±.020
1.000±.008
.752±.008
23.063±.024
.748±.008
19.563±.020
.205±.008 X .453±.008
.181±.008 X .205±.008
5X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-28-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 28" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
31±.118" SLIDE TRAVEL 30±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-30-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 30" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008 4X .256±.008
.252±.008 1.000±.008
3.252±.016 11.752±.020
26.252±.024
.622±.008
28.504±.024
2X .362±.008 X .276±.008
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012 5.000±.016
7.500±.020
1.000±.008
.752±.008
25.063±.024
.748±.008
21.563±.024
.205±.008 X .453±.008
.181±.008 X .205±.008
5X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-30-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 30" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
33±.118" SLIDE TRAVEL 32±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-32-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 32" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2017
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
6X .220±.020 90 INSIDE
.252±.008 1.000±.008 3.252±.016
9.252±.020
16.502±.020 21.752±.024
28.252±.024
.622±.008
30.504±.024
2X .327±.020 X .248±.02090 INSIDE
5X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012 5.000±.016
7.500±.020
1.000±.008
.752±.008
27.063±.024
.748±.008
23.563±.024
.181±.008 X .205±.008
.205±.008 X .453±.0085X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-32-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 32" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2017
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
35±.118" SLIDE TRAVEL 34±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 6/28/2018 NS2 UPDATED TO CURRENT REVISION 9/4/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-34-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 34" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
6X .220±.020 90 INSIDE
.252±.008 1.000±.008
3.252±.016 9.252±.020
16.502±.020 23.752±.024
30.252±.024
.622±.008
32.504±.024
2X .327±.020 X .248±.02090 INSIDE
7X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012 2.500±.012 5.000±.016
7.500±.020
14.500±.020 20.504±.024
1.000±.008
.752±.008
29.063±.024
.748±.008
25.563±.024
.181±.008 X .205±.008
.205±.008 X .453±.0085X .374±.008 X .205±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/4/2019
I-DS-2250-34-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 34" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
37±.118" SLIDE TRAVEL 36±.024" SLIDE LENGTH
SCALE: 1:10
SCALE: 1:2
2.087+-.020.000
.752+-.028.000
RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES
SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS
REVISIONSREV. DESCRIPTION DATE BY
1 INITIAL RELEASE 1/14/2019 RGM2 UPDATED TO CURRENT REVISION 9/11/2019 KC
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/11/2019
I-DS-2250-36-QDPART NUMBER:
STEELMATERIAL:
SHEET 1 OF 2
2250 SERIES 36" SLIDE
KCHEN 2SCALE:
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
-
THIRD ANGLE PROJECTION
.197±.008
6X .220±.020 90 INSIDE
.252±.008 1.000±.008 3.252±.016
9.252±.020 16.502±.020
25.752±.024 32.252±.024
.622±.008
34.504±.024
2X .327±.020 X .248±.02090 INSIDE
7X .205±.008 .413±.008
.752±.008
1.252±.039
.752±.008
1.500±.012 2.000±.012
2.500±.012 5.000±.016
7.500±.020 14.500±.020
20.504±.024 27.563±.024
1.000±.008
.752±.008
31.063±.024
.748±.008
5X .374±.008 X .205±.008.181±.008 X .205±.008
.205±.008 X .453±.008
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]
.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"
ANGULAR: 1.0
QUALITY
DO NOT SCALE9/11/2019
I-DS-2250-36-QDPART NUMBER:
STEELMATERIAL:
SHEET 2 OF 2
2250 SERIES 36" SLIDE
KCHEN 2SCALE: 1:4
REV
ASIZE
NAMEDATE
ENGR SALES
ZINC PLATEDDESCRIPTION:
NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.
FINISH:
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.
BW12/19/2019
PN12/17/2019
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
I-DS-2250-10-QD_REV_2I-DS-2250-12-QD_REV_2I-DS-2250-14-QD_REV_2I-DS-2250-16-QD_REV_2I-DS-2250-18-QD_REV_2I-DS-2250-20-QD_REV_2I-DS-2250-22-QD_REV_2I-DS-2250-24-QD_REV_2I-DS-2250-26-QD_REV_2I-DS-2250-28-QD_REV_2I-DS-2250-30-QD_REV_2I-DS-2250-32-QD_REV_2I-DS-2250-34-QD_RVE_2I-DS-2250-36-QD_REV_2I-DS-2250-8_REV_2