ich-dellsvr排版 2科勒
TRANSCRIPT
VITREOUS CHINA UNDERCOUNTER LAVATORY/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONSLADENA
K-2214X
295mm
464 mm
RIM OF LAVATORY
CUT ALONG THIS LINE
CLIP LOCATIONS
�
�
, 2013Copyright Kohler China Ltd., 2013
1230576-T01-A
64 mm
70 mm
NOTE: before cutting countertopAllow for handle clearance /
FINISHED WALL / BACK SPLASH
CENTERLINE OF FITTING
�
�
�
0 Co
IMPORTANT CONSUMER
INFORMATION
(CARE AND CLEANING)
�
�
�
To keep your lavatory looking new, make sureyou rinse it out thoroughly after each use.
on this product, asthey will scratch and ruin the surface.Stubborn stains, paint, or tar can be removedwith turpentine or paint thinner.Do not use the product in the water below 0 C.
DO
NOT USE ABRASIVES
o
Please do not use hard materials (likescouring pad) to clean product surface,especially the product logo.
SERVICE PARTS
52047Lav Clamp Accessory
�
�
�
�
�
�
( 13 )
�
�
�
�
�
�
�
�
�
BEFORE YOU BEGIN�
�
�
�
�
�
Due to the nature of the installation, undercounterlavatories should be installed by trained and experiencedinstallers.Do not use adhesives or adhesive sealants with thisproduct.Inspect the waste and supply tubing; replace if necessary.Prior to installation, unpack the new lavatory and inspect itfor damage. Return the lavatory to its protective cartonuntil you are ready to install it.Observe all local plumbing and building codes.Kohler lavatory is made according to American NationalStandard that it can match the American lavatory fittings.Any other lavatory fittings may not fit for kohler lavatory.
TOOLS AND MATERIALSSealantPencilTape measureSharp knife or scissorsKeyhole or saber sawDrill (13mm dia. drill bit or larger)Safety glassesHammerRags or paper toweling
You may require different, more specialized tools toinstall this lavatory to countertop materials other than wood orwood composites.
NOTE:
�
�
�
�
�
�
�
�
�
13
10 16
25
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
INSTALL THE LAVATORY
FOR WOOD COUNTERTOPS
FOR MARBLE COUNTERTOPS
FOR ALL INSTALLATIONS
NOTE: Install so future removal from underneath the countertop ispossible to avoid damage to the countertop.
Check the desired lavatory location for clearance between the backsplash,faucet, fixture, and cabinet.Cut out the template.Carefully position and trace the template on the countertop as directed onthe template.Mark the faucet hole centerline on the countertop.Drill a 13mm pilot hole on the inside of the cut line.Cut out the countertop opening with a saber or keyhole saw.
Mark and pre-drill the wood screw holes at the locations shown on thetemplate.Waterproof any exposed areas of wood.
Position the countertop upside down on foam padding to protect thesurface. Mark and drill 10mm holes 16mm deep at the locations shown onthe template.Use a setting tool and hammer to secure the anchors.
If the countertop has not been installed, install it at this time.Drill the faucet holes according to the faucet installation instructions.Install the faucet to the countertop according to the manufacturer sinstructions.Install the drain to the lavatory according to the manufacturer s instructions.
Do not use adhesives or adhesive sealants.
Apply a continuous bead of quality sealant to the lavatory rim where it willcontact the countertop.
The screws provided should be used on countertops with a minimum25mm thickness. For thinner countertops, use appropriate anchors andfasteners.
For wood, wood composite, and marble countertops, install the lavatory tothe countertop with the clamps and screws provided. For other countertopmaterials, refer to the countertop manufacturer s instructions forrecommended fasteners.Position the lavatory squarely under the cutout before tightening theclamps. Draw the lavatory rim up to the countertop until it is snug.
Immediately wipe away any excess sealant.Make the final drain and faucet connections to complete the lavatoryinstallation. Be sure to follow all instructions packed with the drain andfaucet.Clean up with a cleaner.
NOTE:
NOTE:
Do not
overtighten.
non-abrasive
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
Marble
FoamPadding
Anchor
Setting Tool
Note: waterproof unprotected overhangarea on the underside of wood counter.
SealantSealant
Marble Installation Wood Installation
9.6HOT 9.6
COLD32 OD
OF FITTINGCL
ROUGHING-IN
(ASME)A112.19.2-2008
25
K-2214X (X)=530 (Y)=365
Roughing-In Notes
Fixture dimensions are nominal and conform totoler-ances in ASME Standard A112.19.2-2008.
Supplied basin clamp assemblies require 25mmminimum countertop thickness. Installer mustsupply anchors for thinner countertops.
K-2214X: (X)=530mm, (Y)=365mm 6mmNOTE: Using this template, theoverhung is about 6mm. Customerscan zoom the template by scale tomeet their requirement.
Apply Sealant
Clamp
Kohler reserves the right to change marked dimensions without prior notice.
Unit: mm:
Reference Value
121
(X)
(Y)
29
13
206
356 349
102
10
16
25Max
610102
864686
203Min
229 Min
152Max
Recommended ADA Installation
Wood Screw
Anchor Screw