ics l85 l86 series manual
TRANSCRIPT
ICS-85 L85 A2ICS-86 L86 A2ICS-87 L85 A2 CARBINE
L85/L86L85/L86 aeg series
L85
L85
aeg
ser
ies
aeg
ser
ies
Component names
3.
ICS-85 L85 A2
ICS-86 L86 A2
L86 A2
Model Weight Length Bullet Caliber
4411 g 912.8 mm 6 mm BB450 Round450
L86 A2
L85 A2
Model Weight Length Bullet Caliber
3652 g 786.5 mm 6 mm BB450 Round450
L85 A2
Flashhider
Flashhider
BipodBipod plate
Barrel
Barrel handguard
Upper handguard
handguard
Front sight
Front sight
Charging handle
Charging handle
Carry handle
Carry handle
Safe pin
Safe pin
Upper handguard
A2 handguard
Handguard move button
Butt plate
Butt plate
Bolt catch
Bolt catch
Rear sling clip
Rear sling clip
Magazine
Magazine
Pistol grip
Pistol grip
Trigger
Trigger
Grip
Grip
L85
L85
aeg
ser
ies
aeg
ser
ies
ICS-85 L85 A2
ICS-86 L86 A2
4.
1 2 3
1 2 3
Battery fitting method
Open upper handguard, press move button,and pull handguard.
Open upper handguard. To pull open handguard.Move sideward and insert battery, than close it.
Insert battery and connect wire
Assemble handguard and manage wire, close upper handguard
5.
L85
L85
aeg
ser
ies
aeg
ser
ies
Gear box ICS-85 L85 A2
ICS-86 L86 A2
1 2 3
Reassembly is reverse of disassemblys procedures
Move rear pin and disassemble butt plate
Close bipodPush bipod plate and close bipod put legs on plate
Open bipodPull bipod plate, turn out legs and off hand.
Front pin
Move front pin and disassemble main body.Turn upside down to avoid gearbox dropping,release motor wire and take off gear box.
Bipod
6.
L85
L85
aeg
ser
ies
aeg
ser
ies
1
23
Fine adjustment of gear engagement.
Hop UpHop Up adjustment
*
Best trajectory
Increase Hop adjustment
Decrease Hop adjustment
Don't adjust yourself.
Adjustment procedure:1.Backward Hop up , pellet will float up.2.Forward Hop up , pellet will fall down.(also can use cross screw driver)
After release butt plate, use screw driver to adjust, when finish adjusting, close the plate.
Release 2 pins on left side, push forward and take off handle.
Move charging to end and pull up the charging pin,after adjust hop up, pull back charging it will go forward.
Disassemble carry handle
Full automatic
Semi automatic
Magazine attachment
Selector lever and safety setting
7.
L85
L85
aeg
ser
ies
aeg
ser
ies
DOWN UP
Bear sight and front sight adjustments
F
S
F
S
Open the cover to loadBBs. Please use ICS 6mm caliber BBs for optimum Performance.
Turn to F, pull triggercan shoot.
Turn to S, pull triggercan't shoot.
Use screw driver to press down button, adjust sight high or low.
To charge BB feed spring, please wind magazine.
Magazine loading and unloading load BBs
Press the magazine release lever to load or unload the magazine.
Safe convert
8.
L85
L85
aeg
ser
ies
aeg
ser
ies
How to use a cleaning rod
BackwardClose destination :move sight backward
:
Right
Clockwise
Left
Counter clockwise
ForwardFar destination :move sight forward
:
Release box pin, 3 position spring compress.
Middle hole for median power
Front hole for low power Rear hole for high powerInsert cleaning rod, turn left and right, move back and forward.
Rear sight and adjustmentsSpring adjustment
L85
L85
aeg
ser
ies
aeg
ser
ies
Description
9.
L85 A2 / L86 A2 Compatible component
ML-12
MA-04
Detachable carring handle
Hi-cap mag 450 load
ML-13 ML-15
ML-06
ML-17
ML-16
Upper receiver set Charging set
L85 Butt plate set
Metal spring guide
Gearbox assembled
Lower receiver set
Switch set
Upper connect set
Pistol Grip set
ML-18
MC-68
ML-14
ML-09
ML-10
ML-08
450
L85
BoxMotor-short pin
Motor shell
L85 A2 L85 A2 PARTS
L86 A2 L86 A2 PARTS
10.
ML-24
ML-25
ML-21
ML-05
ML-11
ML-11
L86 Butt plate set
ML-20
ML-04
L85 Front outer barrel set
Gas tube
Gas tube
L86 Front outer barrel set
ML-19
L86 Flashhider
L85 Flashhider
ML-03
ML-01
L85 Handguard set
L86 Handguard set
L86 Bipod set
ML-02
L85 Front sight
MC-16
MC-16
ML-07
ML-07
ML-22
ML-23 Hop bucking
Hop bucking
Hop up set
Hop up set
L86
L86
L86
L85 L85 Inner copper barrel
L86 Inner copper barrel
L86
L85
L86
L85
L85
L85
Hop up
Hop up
L86L86 Grip
L86