identifying the cellular radio system describes the principles and characteristics of cellular radio...
TRANSCRIPT
Identifying the cellular radio system
Describes the principles and characteristics
of cellular radio
Draw a block of unit moblile communication
' Explain the functions of each block of the mobile
communications
Differentiate control channels and voice channels
Identifying the types and characteristics of
the antenna
OBJECTIVE :
INTRODUCTION
Cellular Radio Communications System is a two-way form of communication.
using radio waves
cellular phone can be connected to the telephone system,where it is connected to the world.
Bell Telephone Company, the AT & T has
create a cellular radio system at the end of the 70s and
fully implemented in early 1980.
Known as ‘Advanced Mobile Phone Service’(AMPS).
CELLULAR RADIO PRINCIPLES
Each cell consists of a receiver and transmitter with
low power called 'Radio Base Station' (RBS) .
enable it to provide services to the user in the
coverage of several square kilometers.
Sel
MTSO
There are transmitter and
receiver where it divides its
services to smaller areas called
“CELL”The smaller the radius of a cell, the higher the available bandwidth. So, in highly
populated urban areas, there are cells with a radius of a few hundred metres, while
huge cells of up to thirty kilometres provide coverage in rural areas.
Each cell is connected by telephone
lines or microwave to the Main Control Center,
known as ‘Mobile Telephone Switching
Office’(MTSO).
CHARACTERISTICS OF CELLULAR RADIO COMMUNICATION SYSTEM When user moves out of one cell to another
cell, they automatic switching system to the
another RBS.
Recipients in each cell will monitor the signal
strength of
the mobile unit. When signal strength falls to a level
below the prescribed level, or reference, then it will
automatically be switched to a higher level through the
nearest RBS.
BASIC COMPONENT OF RADIO CELLULAR COMMUNICATION SYSTEM
I. Unit Mobile :
Is a consumer devices that used to make and receive calls.
II. Radio Base Station (RBS):
Is an outside station-guard cells Controller that received instructions from the MTSO.
using the radio channel that found in every cell including the voice channels and control channels
Supervise the call which includes monitoring on speech quality and measurement on the strength of the voice signal.
Send and receive voice signals and data from/to consumers.
as an interface between users and systems.
III. Mobile Telephone Switching Office (MTSO):
A mobile switching center, as the heart of the system
Perform the switching operation between cellular networks and public telephone network.
Receive and process data received from the RBS include
the status of mobile units, diagnostic data, information for billing, data text and so on.
implementing supervisory that determine and updating
the locations of mobile units when there
is movement from one cell to cell.
Implementing the flow to determine the appropriate cells and the necessary radio channels
when a call is to be made.
Transmiter
Frequency Synthesizer
Receiver
Logic Unit
Control Unit Cellular Phone CELLULAR PHONE BLOCK
DIAGRAM
TRANSMITTER.Low-
power FM transmitters, frequency range 825MHz to 845 MHz.Has
a transmission channel 666 at a distance of 30 kHz each other.
Power emissions:Mobile radio = 3 WMobile phone = 500 mW
FREQUENCY SYNTHESIZER.
To generate the signals for the use of transmitter and
receiver
Using a PLL circuit (Phase Locked Loop), where the hablor oscillator provide the frequency needed.
RECEIVER.
It is dual-conversion superhetrodin.
Frequency Range= 870.03 MHz to 870.98 MHz.
there are 666 channel
receiver at 30 kHz frequency
range of each other.
For each channel, the frequency of transmission and receiving distinguished at a distance of 45 MHz. For example; at a frequency transmission channel is 825.03MHz while the frequency of acceptance for Channel 1 is 870.03 MHz, then the difference between them is 45 MHz.
LOGIC UNIT.
Consist of main control circuit for cellular unit
This part is using a microprosessor (RAM &ROM.)
Contains an additional circuit which is used to interpret signals from
the MTSO or cells, and to generate control signals for
the transmitter and receiver.
CONTROL UNIT .
Consist of speaker, microphone and keypad(touch-tone).
Microprocessor used to control the LCD display and indicators in
unit mobile.
microprocessor memory is capable of storing the frequently
called numbers and the automatic dialing system.
Radio Channel
is a two way radio transmission path between the RBS(Radio Base Station) and mobile units
Each channel uses different frequencies for transmissionfrom the RBSanother transmission from mobile unit to RBS
Use different frequencies to avoid interference or overlapping signal between transmitter and receiver
Frequency @ the same channel can be used by other cells that are far away from each other
Control Channel
Each cell has one (1) control channel that is used only for transmission of data (not voice)
Control channel continuously control the flow of data when the mobile unit is ON
When the user moves from one cell to another cell, the terminals will be adjusted to a new control channel automatically within the operating system.Control channel with the best reception quality will be selected and set of mobile terminals will then be adjusted to this channel until the quality of reception decreases.
Voice Channel
Channel which brought conversation signal and used during conv
ersation took place
Each cell usually has between 7 to 23 voice channels
Besides bringing the conversation signals, this channel also route to:
*Tone generator SAT (Supervisory Audio Tone)* Data Message*Signaling tone detection *Ringing order delivery
At Radio Base Station (RBS), there are TWO(2) types of antenna used:- Omnidirectional DirectionalAntenna is used as a medium of communication between
the receiver and transmitter signal.
Antenna
Antenna has a stability of sending and receiving signals.Used in less populated areas/rural areasThe coverage area round in shape and every coverage area circle end would overlap between one anotherUsing only one element.
Omnidirectional Antenna
Antenna that have a directional nature, where transmission is in a certain direction.Requires three antennas arranged so that each antenna near a corner of 120 coverageUsed in large areas such as urban, town
Directional Antenna
Omnidirectional DirectionalCoverage area = Circle-shaped area and overlap each other
Coverage area = Balanced coverage area and are arranged in a hexagonal and non-overlapping
antenna beam = 360 each RBS
antenna beam = 120 each RBS
RBS = located at the middle of cell.
RBS = located at the edge of cell
Used = in rural areas/low population area
Used = in urban/town areas or high population area
COMPARISON
QUIZ 21) What is the basic component of radio
cellular communcation system?2) Cellular radio principles is
____________________________________________________________________________________
3) Differentiate directional and omnidirectional antenna.