ilcdowner's tv i plasmamanual tv · mfl34797033-en-simple 1/20/04 12:34 am page 1
TRANSCRIPT
MFL34797033-en-simple 1/20/04 12:34 AM Page 1'<_;3
I LCD TV I PLASMA TVOWNER'S MANUALLCD TV MODELS
32LC7D
32LC7DC
37LC7D
42LC7D
32LG10
PLASMA TV MODELS
42PC5D
42PC5DC
50PCSD
50PC5DC
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).
As an ENERGY STAR
Partner LGE U. S. A.,Inc.has determined that this
product meets the
ENERGY STAR guidelinesfor energy efficiency.
An extended owner's manual that contains information
on the advanced features of these LG TV sets is located
on the CD-ROM provided in an electronic version.
To read these files, you will need to use personal computer
(PC) equipped with a CD-ROM drive.
P/NO : MFL34797033 (0807-REV04)Printed in Korea
MFL34797033-en-simple 1/20/04 12:34 AM Page 2'<::3
WARNING / CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NOUSER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
Class B digital device
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection againstharmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However_
there is no guarantee that interference will not
occur in a particular installation. If this equipmentdoes cause harmful interference to radio or televi-
sion reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipmentand receiver.
- Connect the equipment to an outlet on a circuitdifferent from that to which the receiver is con-
nected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
This reminder is provided to call the CATV systeminstaller's attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding sys-
tem of the building, as close to the point of the cable
entry as practical.
Do not attempt to modify this product in any waywithout written authorization from LG Electronics.
Unauthorized modification could void the user's
authority to operate this product
2
MFL34797033-en-simple 1/20/04 12:34 AM Page 3'<::3
SAFETYINSTRUCTIONS
IMPORTANT SAFETYINSTRUCTIONS
Read these instructions.
Keep these instructions.Heed all warnings.Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install inaccordance with the manufacturer's instructions.
Do not install near any heat sources such asradiators, heat registers, stoves, or other apparatus(including amplifiers)that produce heat.
Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other. Agrounding type plug has two blades and athird grounding prong, The wide blade or thethird prong are provided for your safety. If theprovided plug does not fit into your outlet,consult an electrician for replacement of the
obsolete o
Protect the power cord from being walked onor pinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.
Only use at2achments/accessories specified bythe manufacturer.
Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the apparatus. When a cart is used, usecaution when moving the cart/apparatus com-bination to avoid injury from tip-over.
O Unplug this apparatus during lighting stormsor when unusedfor long periods of time.
@ Refer all servicing to qualified service personnel.Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply cord or plug is damaged, liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposed torain or moisture, does not operate normally, orhas been dropped.
@
Never touch this apparatus or antenna duringa thunder or lighting storm.
When mounting a TV on the wall, make surenot to install the TV by the hanging power andsignal cables on the back of the TV.
Do not allow an impact shock or any objects tofall into the product, and do not drop onto thescreen with something.
CAUTION concerning the Power Cord:
It is recommend that appliances be placedupon a dedicated circuit; that is, a singleoutlet circuit which powers only that applianceand has no additional outlets or branchcircuits. Check the specification page of thisowner's manual to be certain.
Do not connect too many appliances to thesame AC power outlet as this could result infire or electric shock.
MFL34797033-en-simple 1/20/04 12:34 AM Page 4'<::3
SAFETYINSTRUCTIONS
@
@
@
Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets, extensioncords, frayed power cords, or damaged orcracked wire insulation are dangerous. Any ofthese conditions could result in electric shockor fire. Periodically examine the cord of yourappliance, and if its appearance indicates damageor deterioration, unplug it, discontinue use ofthe appliance, and have the cord replaced withan exact replacement part by an authorizedservicer. Protect the power cord from physicalor mechanical abuse, such as being twisted,kinked, pinched, closed in a door, or walkedupon. Payparticular attention to plugs, walloutlets, and the point where the cord exits theappliance.Do not make the TV with the power cordplugged in. Do not use a damaged or loosepower cord. Be sure do grasp the plug whenunplugging the power cora. Do not pulFon thepower cora to unplug the TV.
WARNING - To reduce the risk of fire or elec-trical shock, do not expose this product to rain,moisture or other liquids. Do not touch the TVwith wet hands. Do not install this product nearflammable objects such as gasoline or candlesor expose the TV to direct air conditioning.
Do not expose to dripping or splashing and donot place objects filled with liquids, such asvases, cups, etc. on or over the apparatus (e.g.on shelves above the unit).
GROUNDING
Ensure that you connect the earth ground wireto prevent possible electric shocl< (i.e. a TVwith a three-prong grounded AC plug must beconnected to a three-prong groundea AC out-let). If grounding methods are not possible,have a qualified electrician install a separatecircuit breaker.
Do not try to ground the unit by connecting itto telephone wl_res, lightening rods, or gas pipes.
Power
Supply
DISCONNECTING DEVICE FROM MAINSMains plug is the disconnecting device. Theplug must remain readily operable.
@ Keep the product away from direct sunlight.
@ ANTENNAS
Outdoor antenna groundingIf an outdoor antenna is installed, follow theprecautions below. An outdoor antenna systemshould not be located in the vicinity of over-head power lines or other electric light orpower circuits, or where it can come in contactwith such. power lines or circuits as death orserious Injury can occur.Be sure the antenna system is grounded so asto provide some protection against voltagesurges and built-up static charges.Section 810 of the National Electrical Code(NEC) in the U.S.A. provides information withrespect to proper grounding of the mast andsupporting structure, grouncting of the lead-inwire to an antenna discharge unit, size ofgrounding conductors, location of antenna dis-charge unit, connection to grounding electrodesand requirements for the grounding electrode.Antenna _roundin_ accordin_ to theNational Eqectrical _:ode, ANSI7NFPA 70
Ground Clamp Antenna Lead in Wire
_ ntenna Discharge Unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-21 )
_/ Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Pad H)
NEC: National Eleclrical Code
@ CleaningWhen cleaning, unplug the power cord andscrub gently with a soft cloth to preventscratching. Do not spray water or other liquidsdirectly on the TV as electric shock may occur.Do not clean with chemicals such as alcohol,thinners or benzene.
MovingMake sure the product is turned off,unplugged and all cables have been removed. Itmay take 2 or more people to carry larger TVs.Do not press against or put stress on the frontpanel of the TV.
VentilationInstall your TV where there is proper ventila-tion. Do not install in a confinedspace such asa bookcase. Do not cover the product withcloth or other materials (e.g.) plastic whileplugged in. Do not install in excessively dustyplaces.
If you smell smoke or other odors coming fromthe TV or hear strange sounds, unplug thepower cord contact an authorized service center.
On Disposal (Only Hg lamp used LCD TV)The fluorescent lamp used in this product contains asmall amount of mercury. Do not dispose of thisproduct with general household waste. Disposal ofthis product must be carried out in accordance to theregulations of your local authority.
4
MFL34797033-en-simple 1/20/04 12:34 AM Page 5'<::3
WARNING / CAUTION ............................ 2
SAFETY INSTRUCTIONS ..........................3
VCR Setup ..................................................... 19
PC Setup ........................................................ 20
Accessories ...................................................... 6
Front Panel Information ...................................... 7
Back Panel Information ...................................... 8
Remote Control Functions ............................... 10
Back Cover for Wire Arrangement ..................... 12
Attaching the TV to a wall ................................ 14
Desktop Pedestal Installation ............................ 14
Stand Installation ............................................ 15
VESA Wall Mounting ........................................ 15Antenna or Cable Connection .......................... 16
Turning On TV ................................................ 21
Channel Selection ........................................... 21
Volume Adjustment ......................................... 21
Channel Search ............................................... 22
On-Screen Menus Selection ............................. 23
Troubleshooting .............................................. 26Maintenance ................................................... 28
Product Specifications ..................................... 29
Open Source Software Notice .......................... 30
HD Receiver Setup ......................................... 17
DVD Setup ...................................................... 18
HOW TO USE THE OWNER'S MANUAL ON THE CD-ROM
To view the Owner's Manual on the CD-ROM, Adobe Acrobat Reader must be installed on your PC.
The "ACRORD" folder on the CD-ROM contains the installation programs for them.
If you want to install those programs, Open the "My Computer"--_Open the "LG"--_Open the
"ACRORD"--_ double-click your language.
TO VIEW THE OWNER'S MANUAL ON THE CD-ROM
The Owner's Manual files are included in the supplied CD-ROM.
Load the supplied CD-ROM into the CD-ROM drive of your PC.
After a while, the web page of the CD-ROM will o )en automatically.
w
When you select your product,
display the PDF file.
'for Window only)
.... 'i_/__
+:
You can find the desired contents
easily using the bookmark.
MFL34797033-en-simple 1/20/04 12:34 AM Page 6'<::3
PREPARATION
I-r1
0z
Ensure that the following accessories are included with your product. If an accessory is missing, please con-
tact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standardcompliance for the product.
The accessories can be different from the figures shown here.
For further information, see the the Owner's Manual files supplied CD-ROM.
Owner's Manual CD Manual Remote Control,(Refer to p.5) Batteries
Power Cord
75ohm Round Cable
(This feature is not available for
all models)Polishing Cloth
* Slightly wipe stained spot on the exterior only with the polishing
cloth for the product exterior if there is stain or fingerprint on
surface of the exterion
* Do not wipe roughly when removing stain. Please be cautions of
that excessive pressure may cause scratch or discoloration.
® _ o - ° o ® - -
This feature is not available for all models
2-Eye-bolts 2-Wall brackets(Refer to p.14) (Refer to p.14)
@w ® °
D-sub 15 pin Cable
Cable
Management
6
MFL34797033-en-simple 1/20/04 12:34 AM Page 7'<::3
FRONT PANEL[NFORMATMON
+ Here shown may be somewhat different from your TV.
m NOTE: If your product has a protection tape attached, remove the tape.And then wipe the product with a cloth (Ira polishing cloth is included with your product, use it).
Front Panel Controls
Plasma TV Model
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates green when the set is switched on.
-D
©z
Remote Control Sensor
'OWER INPUT MENU ENTERButton Button Button Button
VOLUME CHANNEL
(_1,1_) Buttons (V,A)Buttons
LCDTV Model
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates green when the set is switched on.
(&,V) Buttons
(_,')Buttons
Button
Button
Button
MFL34797033-en-simple 1/20/04 12:34 AM Page 8'<::3
BACK PANELINFORMATIONHere shown may be somewhat different from your TV.
m
©z
PlasmaTV Model
ii!iiiii__iii_iiiiiiiii_;:!!_illD--. 0
LCDTV Model
iiiiiiii_!:!!i!!i!!i!!i!!:!i!!i:!i_:_!:_!:_!:_!:_i
-- iiiiiiii_l i_-.......0
8
MFL34797033-en-simple 1/20/04 12:34 AM Page 9'<::3
-o;om
;o
©z
HDMI/DVI IN 1, HDMI IN 2
Connect a HDMI (DVI) connection to either input.
O COMPONENT IN
Connect a component video/audio device to thesejacks.
RGB (PC)
Connect the output from a PC.
AUDIO (RGB/DVI)Connect the audio from a PC or DTV.
O SERVICE
Remote Control Port
Connect a wired remote control.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio from various types of equipment.
Note: In standby mode, these ports do not work.
O RS-232C IN (CONTROL & SERVICE) PORTFor external control devices.
AUDIO OUT
Connect analog audio to various types of equipment.
@ AV (Audio/Video) IN
Connect audio/video output from an externaldevice to these jacks.S-VIDEO
Connect S-Video out from an S-VIDEO device.
O Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
9
MFL34797033-en-simple 1/20/04 12:34 AM Page i0'<::3
REMOTE CONTROL FUNCTMONSWhen using the remote control, aim it at the remote control sensor on the TV.
-O;Oi-m
;o
©z
MODE Select the remote's operating mode. TV, DVD, VCR,AUDIO, CABLE, or STB.
VCR/DVD Control video cassette recorders or DVD players.control buttons
MENU
BRIGHT -/+
THUMBST[CK(Up/Down/Left
Right/ENTER)
EXIT
VOLUME UP/DOWN
MUTE
FAV
CHANNELUP/DOWN
NUMBER button
-- (DASH)
Displays the main menu.
Adjust the brightness on screen.
Navigate the on-screen menus and adjust the system set-tings to your preference.
Clear all on-screen displays and return to TV viewingfrom any menu.
TIMER Select the amount of time before your TV turns off auto-
matically.
RATmO Change the aspect ratio.
S[MPL[NK See a list of AV devices connected to TV. When you tog-
gle this button, the SimpLink menu appears at the screen.
Increase/decrease the sound level.
Switch the sound on or off.
Scroll through the programmed Favorite channels.
Select available channels.
Used to enter a program number for multiple programchannels such as 2-1,2-2, etc.
BACK Tune to the last channel viewed.
10
MFL34797033-en-simple 1/20/04 12:34 AM Page ii'<::3
POWER
TV INPUT
INPUT
Turns your TV or any other programmed equipment on or off, depending on the mode.
In AV 1-2, Component 1-2, RGB-PC, HDMI1, and HDMI2 input sources, screen returns to thelast TV channel.
External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI 1 andHDMI2.
(AV 1 -2, Component 1-2, RGB-PC, HDMI1, and HDMI2 input sources are linked automatically,only if a device is connected.)
-D
m
©z
Inside the Sliding Cover
PICTURE Selects the factory preset picture depend onthe viewing environment.
SOUND Selects the factory preset sound for type of
program.
SAP oAnalog mode: Selects MTS sound (Mono,Stereo, or a SAP)
oDTV mode: Changes the audio language.
CC Select a closed caption.
-- ADJUST Adjust the screen resolution, position, size andphase.
11
MFL34797033-en-simple 1/20/04 12:34 AM Page 12'<::3
-o;om
;o
©7
BACK COVER FOR WMREARRANGEMENT
Here shown may be somewhat different from your TV.
Plasma TV Model
Hold the CABLE MANAGEMENT with both hands and pull it backward as shown.
O
CABLEMANAGEMENT
Connect the cables as necessary.
To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
O Install the CABLE MANAGEMENT as shown.
12
MFL34797033-en-simple 1/20/04 12:34 AM Page 13'<_13
LCDTV Model
Connect the cables as necessary.To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
-o
m
©z
Install the CABLE MANAGEMENT as shown.
CABLE MANAGEMENT
Bundle the cables the TWISTER HOLDER.using supplied
(This feature is not available for all models.)
TWISTER HOLDER
13
MFL34797033-en-simple 1/20/04 12:34 AM Page 14'<::3
-o;om
;o
©z
ATTACHING THE TV TO A WALLThis feature is not available for all models.
m Here shown may be somewhat different from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don't climb on or hang from the TV.
Plasma TV Model LCDTV Model
I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
I Use a sturdy rope (not provided as parts of the product, must pur-
chase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.
DESKTOP PEDESTALINSTALLATION
For proper ventilation, allow a clearance of 4inches on all four sides from the wall.
PlasmaTV Model LGD TV Model
I 4 inches I 4 inches
4 inches 4 inches 4 inches 4 inches 4 inches 4 inches
14
MFL34797033-en-simple 1/1/04 6:57 AM Page 15 _ii_
STAND INSTALLATION (ooly3ZLCZD/zDC,37LCZD,3ZLCl0)
Carefully place the product screen side down on
a cushioned surface that will protect product and
screen from damage.
Assemble the product stand with the product asshown.
-D;Dm
7>
©z
Securely install the 4 bolts provided.
VESAWALL MOUNTING
This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.
PlasmaTV Model LGD TV Model
600 mm 600 mm,32LG10 only: 200 ram)
400 mm 400 mm
(32LC7D/7DC,32LG10 only:100 mm)
15
MFL34797033-en-simple 1/20/04 12:34 AM Page 16'<::3
ANTENNA OR CABLE CONNECTION
-D
m
©z
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
WallAntenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Outdoor
Antenna
(VHF, UHF)
RF Coaxial Wire (7S ohm)
Single-family Dwellings/Houses
(Connect to wall jack for outdoor antenna)Be careful not to bend the bronze wire
when connecting the antenna.
2. Cable
Cable TV
Wall Jack
RF Coaxial Wire (7S ohm)
UHF
Antenna _ -_
VHF
I To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
i If the antenna needs to be split for two TV's, install a 2-Way Signal Splitter.
i If the antenna is not installed properly, contact your dealer for assistance.
16
MFL34797033-en-simple 1/20/04 12:34 AM Page 17'<_13
EXTERNAL EQUIPMENT SETUPI To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
i This part of EXTERNAL EQUIPMENT SETUP mainly use picture for LCD TV model,
HD RECEIVERSETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
When connecting Component cable
1. How to connect
@ Connect the video outputs (Y, PB, PR) of the digital set
top box to the COMPONENT IN VIDEO 1 jacks on
the set. Match the jack colors (Y = green, PB = blue, and
PR = red).
Connect the audio output of the digital set-top box to
the COMPONENT IN AUDIO 1 jacks on the set.
2. How to use
I Turn on the digital set-top box.
(Refer to the owner's manual for the digital set-top box. operation)
i Select Component 1 input source by using the INPUTbutton on the remote control•
i If connected to COMPONENT IN2 input, select
Component 2 input source•
Y, CB/PB, CR/PR
m
x
m
;oz>
m
_9c-O_rm
z
m
c-O
Yes No
Yes Yes
Yes Yes
Yes Yes
Yes Yes
15•73 59.9415•73 60.00
31.47 59.9431.50 60.00
44.96 59.94
45.00 60.00
33 72 59 94• .33.75 60.0 0
26.97 23.976
2ZOO 24.00
33.71 29.97
33.75 30.00
6Z432 59.94
6Z50 60.00
17
MFL34797033-en-simple 1/20/04 12:34 AM Page 18'<::3
EXTERNALEQUIPMENT SETUP
m
x
m
;Dz>
m
£9c-D
m
z
m
c-D
DVD SETUP
When connecting Component cable
1. How to connect
Connect the video outputs (Y, PB, PR) of the DVD to the
COMPONENT IN VIDEO1 jacks on the set.
Match the jack colors
(Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the
COMPONENT IN AUDIO1 jacks on the set.
2. How to use
i Turn on the DVD player, insert a DVD.
i Select Component 1 input source by using the INPUTbution on the remote control.
i If connected to COMPONENT IN 2 input, select
Component 2 input source.
i Refer to the DVD player's manual for operating instructions.
When connecting HDM[ cable
1. How to connect
@
Connect the HDMI output of the DVD to the
HDMI/DVI IN 1 or HDMI IN 2 jack on the set.
No separated audio connection is necessary.
HDMI supports both audio and video.
2. How to use
iSelectHDMI1 orHDMI2inputsourcebyusingtheINPUT button on the remote control.
i Refer to the DVD player's manual for operating instructions.
2
18
MFL34797033-en-simple 1/20/04 12:34 AM Page 19'<::3
VCR SETUP
When connecting with a RCA cable
1. How to connect
Connect the AUDIO/VIDEO jacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
2. How to use
i Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner's manual.)
i Select AV1 input source by using the INPUT button onthe remote control.
i If connected to AV IN2, select AV2 input source.
m
x
m
z>
m
£9c
m
z
r'_
c
When connecting with an SoVkteo cable
1. How to connect
Connect the S-VIDEO output of the VCR to the
S-VIDEO input on the set.
Connect the audio outputs of the VCR to the AUDIOinput jacks on the set.
2. How to use
I Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner's manual.)
i Select AV1 input source by using the INPUT button on theremote control.
i If connected to AV IN2, select AV2 input source.
19
MFL34797033-en-simple 1/20/04 12:34 AM Page 20'<::3
EXTERNALEQUIPMENT SETUP
PC SETUP
m
x
m
z>
m
£9c
_rm
z
m
c
When connecting Dosub ]5pin cable
1. How to connect
Connect the RGB output of the PC to the RGB (PC)
jack on the set.
Connect the PC audio output to the AUDIO (RGB/DVI)
jack on the set.
2. How to use
I Turn on the PC and the TV.
i Select RGB-PC input source by using the INPUT buRonon the remote control.
When connecting HDM[ to DV[ cable
1. How to connect
Connect the DVI output of the PC to the HDMI/DVI
IN 1 jack on the set.
Connect the PC audio output to the AUDIO
(RGB/DVI) jack on the set.
2. How to use
I Turn on the PC and the TV.
i Select HDMI1 input source by using the INPUT buRon onthe remote control.
Supported Display Specifications
RGB-PC, HDMI1/DVI-PC mode
...............3].:469 ...........................70:98...._ .......... ] * RGB-PC mode only
...............s]:469 ...........................59.94................3Z879 60.31
48.363 60.00
4Z776 59.87
...............4.7.._2q.........................s9..79.9...............4Z 130 5 9.6 5 ®
* LCD TV only
2O
MFL34797033-en-simple 1/20/04 12:34 AM Page 21'<::3
WATCHING TV
TURNING ON TV
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the r_/I, INPUT, CH (A or V)
button on the TV or press the POWER_ INPUT, TV INPUT, CH(A or
11% Number (0~9) button on the remote control.
Select the viewing source by using the TV INPUT, INPUT button on theremote control.
This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
When finished using the TV, press the POWER button on the remote con-trol. The TV reverts to standby mode.
N"I"
Z
<
CHANNEL SELECTMON
Press the CH (A or 11') or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
@
Press the VOL (A or V) button to adjust the volume.
If you want to switch the sound off, press the MUTE button.
You can cancel the Mute function by pressing the MUTE or VOL (A or V)button.
21
MFL34797033-en-simple 1/20/04 12:34 AM Page 22'<::3
WATCHING TV
-1-
z
<
CHANNEL SEARCH
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna
or cable inputs, and stores them in memory on the channellist.
Run Auto Tuning again after any Antenna/Cable connection
changes.
A password is required to gain access to Auto Tuning menu
if the Lock System is turned on.
Press the MENU button and then use • or • button
to select the SETUP menu.
CZ_! CZ2
Press the • button and then use • or • button toselect Auto Tuning.
Press the ENTER button to begin the channel search.
Allow Auto Tuning to complete the channel search
cycle for ANTENNA and CABLE.
22
@
@
@
MFL34797033-en-simple 1/20/04 12:34 AM Page 23'<_13
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Press the MENU button and then use • or • button to select the each menu.
Press the • button and then use • • _1 • button to display the available menus•
SETUP
"""AllavailableTV channels are searched and stored
automatically.
"""User can do manual channel selectionand add or
deleteindividualchannels.
You can add or delete in the channel list•
"1"
Z
<
PICTURE ,,,,Select the preset value in the Picture Mode menu
based on the program category: Dynamic, Standard,Mild, User1, User2.
,,,,Choose one of three automatic color adjustments
: Cool, Medium, Warm, User
,,,,It is LG Electronic's unique picture improving tech-
nology to display a real HD source through an
advanced digital signal processing algorithm•
,,,liSelect Auto or Manual (XD Contrast, XD Color, XD Noise)•
,,,,Cinema 3:2 Mode (On, Off]
Set up the TV for the best picture appearance for
viewing movies•
,,,,Black Level (Low, High)
Adjusting the contrast and the brightness of the
screen using the black level of the screen•
.......Seeci ihe des red p cture format ........................................
......!SetbYpr°gram'4:3'!6!9:Zc'°n_! ;_o°m;_'!ustScan:,,,,Use to quickly reset all the Picture menu options to
their original factory preset values.
,,,,iAdjust the screen Resolution, Position, Size, Phase,Reset.
23
MFL34797033-en-simple 1/20/04 12:34 AM Page 24'<::3
WATCHING TV
"I"
zc_
<
AUDIO
i Sound Mode lets you enjoy the best sound with-
out any special adjustment.
: Standard, Music, Movie, Sports and User
i Scans for changes in sound levels during commer-
cials, then adjusts the sound to match the specifiedaudio level.
,,,[,,,!Act)us! ! h e !eft(r!gh! s° u nct o f spe ake ["............................
[[[[[[[[[[[[[[[[[[[ _ i Turn the TV speaker On or off.
TIME
I Auto: The time is set automatically from a digital
channel signal.
Select your viewing area time zone.
Select Auto, Off, On depending on whether or
not your viewing area observes Daylight Savingtime.
i Manual: Set the clock manually.
ff ...._..Se.!e_:.t..On..?r.gf/".........................................................................
i Select the amount of time before your TV turns off
automatically: Off, 10, 20, 50, 60, 90, 120, 180,240.
24
MFL34797033-en-simple 1/20/04 12:34 AM Page 25'<::3
OPTION
Plasma TV model only
m Select your desired language for on screen menus
: English, Spanish, French.
i +..S?.!.a.._a!??._.!o.e.ach!.?put.s?ur.c?"..........................................m Control and play other AV devices connected to the
TV through HDMI cable without additional cables
and settings.
m This feature can be used to prevent unauthorized
viewing by locking out the front panel controls.
m Mode: When selecting Off, Submenus for Analog,
DTV, and Digital Option become disabled.
m Analog: CC1 - CC4, Text1 - Text4.
m Digital: Service1 _ Service6
,,,,Digital Option: Customize the DTV/CADTV captions
that appear on your screen.
m Use it to minimize any fixed image on the screen.
: Normal, Orbiter, Inversion, White Wash.
m Reduces the plasma display power consumption.
J_ mChoose the desired TV ID number.
"1"
ZC_
<
LOCKFor USA
For Canada
..........................................................................................................................................
m Blocks movies according to the movie ratings limits
specified.
m Prevents children from watching certain children's
TV programs, according to the ratings limit set.
m Based on the ratings, blocks certain TV programs
that you and your family do not want to view.
mSelecting canadian english language rating system.
V g-re ,,,,,,,,Selecting canadian french language rating system.
mThis function may become available in the future and
will be available only for digital channel signal.
m Enables you to select a source to block from the
external source devices you have hooked up.
2S
MFL34797033-en-simple 1/20/04 12:34 AM Page 26'<::3
APPENDIX
TROUBLESHOOTMNG
>*=_*=_
i=m
z
x
i Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
i Ensure that the batteries are installed with correct polarity (+ to % - to -).
i Ensure that the correct remote operating mode is set: TV, VCR etc.
i Install new batteries.
,,,,Check whether the product is turned on.
,,,,Try another channel. The problem may be with the broadcast.
,,,,Is the power cord inserted into wall power outlet?
I Check your antenna direction and/or location.
,,,,Test the wall power outlet, plug another product's power cord into the outlet
where the product's power cord was plugged in.
,,,,This is normal, the image is muted during the product startup process. Please
contact your service center_ if the picture has not appeared after five minutes.
,,,,Adjust Color in menu option.
,,,,Keep a sufficient distance between the product and the VCR.
,,,,Try another channel. The problem may be with the broadcast.
,,,,Are the video cables installed properly?
,,,,Activate any function to restore the brightness of the picture.
,,,,Check for local interference such as an electrical appliance or power tool.
,,,,Station or cable product experiencing problems, tune to another station.
,,,,Station signal is weak, reorient antenna to receive weaker station.
,,,,Check for sources of possible interference.
26
MFL34797033-en-simple 1/20/04 12:34 AM Page 27'<::3
IIIIIIIIPress the VOL or VOLUME button.
IIIIIIIISound muted? Press MUTE button.
illlllllTry another channel. The problem may be with the broadcast.
illlllllAre the audio cables installed properly?
illlllllAdjust Balance in menu option.
iiiiiiiiA change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product. >*=_*=_
i=m
z
x
i Adjust resolution, horizontal frequency, or vertical frequency.
,,,,Check the input source.
IIIIIIIIWork the Auto configure or adjust clock, phase, or H/V position. (Option)
IIIIIIIICheck the signal cable.
IIIIIIIiReinstall the PC video card.
27
MFL34797033-en-simple 1/20/04 12:34 AM Page 28'<::3
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
>*=_*=_
i=m
z
x
Cleaning the Screen
Here's a great way to keep the dust offyour screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it's almost dr),, and then
use it to wipe the screen.
Make sure the excess water is offthe screen, and then let it air-dry before you turn on ),our TV.
Cleaning the Cabinet
I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
m Please be sure not to use a wet cloth.
Extended Absence
28
MFL34797033-en-simple 1/20/04 12:34 AM Page 29'<::3
PRODUCT SPECIFICATIONS
41.5 x 50.2 x 12.2 inches
1048.0 x 766.0 x 510.0 mm
48.9 x 54.9 x 14.6 inches
1242.0 x 8876 x 570.0 mm
AC100-240V - 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-15, UHF 14-69, CATV 1-155, DTV 2-69, CADTV 1-155
75 ohm
52 - 104°F (0 - 40°C)
Less than 80%
>*=_*=_
m
Z
x
31.8 x 23.9x 9.8 inches 36.5 x 273 x 11.0 inches 40.7 x 29.5 x 11.3
30.2 pounds / 13.7 kg
24.7 pounds / 11.2 kg 35.3 pounds / 16.0 kg 45.0 pounds / 20.4 kg
AClOO-240V - 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 _ 104°F (0 _ 40°C)
Less than 80%
I The specifications shown above may be changed without prior notice for quality improvement.
29
MFL34797033-en-simple 1/20/04 12:34 AM Page 30'<::3
OPEN SOURCE SOFTWARE NOTICE
>*=_*=_
i=m
z
x
The following GPL executables and LGPL/MPL libraries used in this product are subject to the GPL/LGPL/MPL
License Agreements:
GPL EXECUTABLES:
i Linux kernel 2.6.12
i busybox
LGPLLIBRARIES:
i uclibc
MPL LIBRARIES:
Nanox
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing
such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at:
This offer is valid for a period of three(g) years from the date of the distribution of this product by LGElectronics.
You can obtain a copy of the GPL, LGPL and MPL licenses on the CD-ROM provided with this product.
i This software is based in part on the work of the Independent JPEG Group.
i This software includes the Zlib compression library, developed by Jean-loup Gailly and Mark Adler.
Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler
3O
MFL34797033-en-simple 1/20/04 12:34 AM Page 31'<_13
MFL34797033-en-simple 1/20/04 12:34 AM Page 32 '<_13
LG e siesln¢o