importance of understanding the atmospheric … of understanding the atmospheric composition ......

85Phone: 800-MALLORY Fax: 360-577-4244 WWW.MALLORYCO.COM

INSTR

UM

EN

TS – INTRODUCTION

Importance of Understanding the Atmospheric CompositionNo matter what type of instruments are used to check environmental gas concentrations, regular monitoring should be performed because a contaminant’s level of combustibility or toxicity might increase even if it initially appears to be low or non-existent. Oxygen deficiency can occur unex-pectedly.

Battery-powered and direct-reading monitoring instruments are classified as two groups – Single-gas and multiple-gas instru-ments, typically monitor-ing one or a combination of the following atmo-spheric conditions:

Oxygen deficiency or enrichmentPresence of combustible gas Presence of certain toxic gases

Some gases are heavier than air, and tend to collect at the bottom of a confined space. Others are lighter, and are usually in higher concen-trations near the top of the confined space. Still others are the same molecular weight as air, so they can be found in varying concentrations throughout the space. This is why test samples should be drawn at the top, middle, and bottom of the space to pinpoint varying concentrations of gases or vapors. These results will have a direct impact on the selection of protective equipment necessary for the tasks in the area.

Combustible GasesIn order for combustion to occur, three elements must be present: fuel, oxygen to support combustion and heat or source of ignition. This is known as the fire triangle.

How Combustible Gas Monitors WorkWhen certain proportions of combustible vapors are mixed with air and a source of ignition is present, an explosion can occur. The range of concentrations over which this reaction can occur is called the explosive range. This range includes all concentrations in which a flash will occur or a flame will travel if the mixture is ignited. The lowest percentage at which this can happen is the Lower Explosive Limit (LEL); the highest percentage is the Upper Explosive Limit (UEL).

Most combustible instruments display gas concentrations as a percentage of the LEL. Some models have gas readouts as a percentage by volume and others display both percent of LEL and percent combustible gas by volume. What’s the difference? For example, the LEL of methane (the major component in natural gas) is 5 percent by volume, and the UEL is 15 percent by volume. If we slowly fill a room with methane, when the concentration reaches 2.5 percent by volume, it is 50 percent of the LEL; at 5 percent by volume it is 100 percent of the LEL. Between 5 and 15 percent by volume, a spark could set off an explosion.

Single-Gas Monitors for Oxygen Deficiency- Oxygen indicators measure atmospheric concentrations of oxygen. Concentrations are generally mea-sured over a range of 0 to 25 percent oxygen in air, with readings being

•

••

INSTRUMENTS

Multi-Gas - Plus .................................. 86 - 90Multi-Gas ............................................. 91 - 95Single-Gas ........................................ 96 - 100Single-Gas Disposables ................ 100 - 102 PID Single-Gas ............................... 102 - 103Specialty Detection ..................................104 Radiation Detection .................................105Fixed Systems ................................ 106 - 107Sampling Pumps & Tubes ............. 108 - 111Testing Kits ..................................... 111 - 112Docking Stations ............................ 112 - 114Specialty Instruments .................... 115 - 118Sound Level Meters ....................... 119 - 120Fit Tester ...................................................120

displayed on either digital readout or an analog meter. Oxygen indica-tors are calibrated with uncontaminated fresh air containing a minimum of 20.8 percent oxygen. With some models, an alarm is activated when oxygen levels drop below 19.5 percent.

Single-Gas Monitors for Combustible Gases- These instruments are generally used to monitor hydrocarbon vapors. These instruments oper-ate by the catalytic action of a heated platinum filament in contact with combustible gases.

Single-Gas Monitors for Toxic Gases- Compact, battery-powered devices can be used to measure levels of such gases as carbon monoxide (CO) or hydrogen sulfide (H

2S), depending on the model selected. Toxic gas

monitors use electrochemical cells. If the gas of interest enters the cell, the reaction produces a current output proportional to the amount of gas in the sample. With these instruments, audible and visible alarms sound if the gas concentration exceeds a preset level. These devices are well suited for use in confined spaces containing motors or engines, which generate CO.

Multiple-Gas Monitors for Oxygen and Com-bustible GasIn some cases it is necessary to determine oxygen and combustible gas lev-els simultaneously. Toxic gas and vapors which can be inhaled or absorbed through the skin are frequently found in confined spaces. Pocketsize monitors and larger handheld devices are used in the work area. These should be designed to monitor continuously.

Photoionization Devices for Toxic Gases and Vapors- These instruments use ultraviolet light to ionize molecules of chemical substances in a gas-eous or vaporous state. Digital readouts allow the user to make immediate determination of gas and vapor concentrations.

Detector Tube Sampling Systems- Quick evaluations of potential haz-ards that cannot otherwise be measured can be drawn through manually operated detector tubes with use of a sampling pump. Most tubes are made of glass, have break-off tips, and are filled with treated chemical granules. They generally have a shelf life of 24 to 30 months.

Personal Sampling- Personal sampling is used to determine the concen-tration of airborne contaminants. Personal sampling pumps are devices used to measure individual workers’ exposures and are typically light-weight, belt-mounted, battery-powered devices.

86 Phone: 800-MALLORY Fax: 360-577-4244 WWW.MALLORYCO.COM

MUL

TI-G

AS -

PLUS

–

INSTR

UM

EN

TS

Orion G Multigas Detector The Orion G Multigas and Leak Detector is a four-gas, multi-function portable detector featuring one-button calibration, rugged construction with excellent resistance to dust and water penetration and advanced ergonomic design.The Orion G Multigas and Leak Detector detects combustible gas leaks and O2, H

2S and CO.

A flexible probe sensor makes it ideal for gas-leak detection at gas meters, bar holes, furnaces, pipes, storage tanks and survey sites. Other applications include confined space monitoring and carbon monoxide detection at flues and furnaces.Simple, intuitive two-button operation allows for easy use with gloved hands, and a large display with great contrast makes it easy to read, even in low-light conditions. With its highly durable construction, the Orion G Multigas and Leak Detector stands up to tough environ-ments.

Other key features of the Orion G Multigas Leak Detector include:Multi-functional flexibility: indoor, outdoor and underground—per-fect for appliances, flues and underground pipes Bar-hole probe filter designed to keep out water and dirt Intrinsically safe leak sensor Ergonomic design that fits snugly in hand Long-life NiMH or alkaline batteries (interchangeable)Fast response timeLeak sensor available on flexible, gooseneck probeInternal pump, for convenient remote samplingSensors that are easy to change

Call for pricing and availability

•

••••••••

Orion® Multigas DetectorA low-cost, reliable, and easy-to-use portable instrument for detecting the presence of O

2, H

2S, CO, and combustible gas. It will stand up to the

roughest handling in even the toughest environments. Economy units come standard with sensors, battery of choice, calibra-tion cap and protective boot. Industrial units include economy features as well as internal pump, 10’ sample line, 1’ probe and orange cordura case. Deluxe units come with the industrial features plus calibration kit and black economy case.Features: Assemble-to-Order Matrix for Orion® Multigas Dectector

One-button calibrationLong-life battery Carbon-filled nylon caseTough, durable constructionBuilt-in pump TIM® System compatibilityLarge, easy-to-read displayDurable sensors Link™ Software compatibility

Item Description Price10025930 Orion,Economy4-GasAlkaline $1,350.0010025932 Orion,Deluxe4-GasNiMH $2,358.0010030399 Orion,Deluxe4-GasDatalogNiMH $2,708.0010030420 Orion,Industrial4-GasNiMH $1,773.00

•••••••••

Mallory is your Instruments Headquarters

Whetheryouneedasingleormultiple-gasinstrument,letMallorybeyouronestopforatmosphericmonitoringequipment.

Therearehundredsofinstrumentsfromavarietyofmanufacturers,andwehavecatalogedasamplingofthetopsellersineachcategory.Whetheryouneedaphotoionizationdevicefortoxicgasesandvapors

oranoxygendeficiencymonitor,Mallorycanhelpmeetyourneedsandbudget.Callustoday-800-MALLORY

Ourcomprehensiverepairandservicedepartmentscancalibrateandmaintainyourinvestment,andrentalunitsarealsoavailable.

When sending an instrument in for repair, photocopy the last page of our catalog and submit with your repair.


INSTR

UM

EN

TS – M

ULTI-GAS - PLUS

FiveStar AlarmProviding the flexibility to meet your gas detection needs, yet incredibly simple to use. The

durable, high-impact case makes it long-lasting, while the advanced ergonomic design and software reduce worker load and simplify operation. This means less time spent training and less time out of service. Over its life, the FiveStar Alarm’s ease of use, safety features, and long-term money savings combine to provide the best in gas detection available today.

Simplicity is obvious from the start:Three well-marked, easy-to-use keysDisplay faces userHigh levels of RFI protectionFlexible smart sensorsWeatherproof—IP54-rated

Advanced features mean safer operation:Limits on sensor zeroingLimits on one-button calibrationUser acknowledges configuration changesData recording is standard

•••••

••••

The FiveStar Alarm saves money:Unbeatable warranty and serviceLong-life combustible sensorOne-button calibration saves training and gas5-gas capability; one detector works as twoBattery “gas gauge” reduces down time20-hour NiMH battery option means one battery can do the job of two

More gas detection capabilities are continually in-troduced. Call for availability of other gas detection capabilities. Some configuration limitations apply.

••••••

You have options! Either select from the most popular kit combinations or “Assemble-to-Order” call 1-800-MALLORY for MSA’s highly effective custom-ordering process.

O2 CO NiCd Battery

AC Charger

Calibration Cap

10ft Line

H2SLEL Leather Jacket

Carrying Case

1ft Probe

Fast Charger

FiveStar Alarm Kit OptionsItem Description Price10018002 Deluxe,4-gas $3,969.00

10018003 Deluxe,3-gas,CO $3,744.00

10018004 Deluxe,3-gas,H2S $3,744.00

10018005 Industrial,4-gas $3,263.00

10018006 Industrial,3-gas,CO $3,038.00

10018007 Industrial,3-gas,H2S $3,038.00

10018008 Economy,4-gas $2,483.00

10018009 Economy,3-gas $2,258.00

10018030 Economy,3-gasH2S $2,258.00

Pulsecheck Pump

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • • • • • • •

Calibration Kit

Gas sensors available - you can order the FiveStar Alarm with sensors to detect:

Combustible gas (0–100% LEL or 0–5% methane)Oxygen (0–25%)

and up to three of the following gases:Ammonia 0–100 ppmCarbon monoxide 0–2000 ppmChlorine 0–20 ppmChlorine Dioxide 0–5 ppmHydrogen sulfide 0–500 ppmNitric oxide 0–100 ppmNitrogen dioxide 0–100 ppmPhosphine 0–5 ppmSulfur dioxide 0–100 ppm

•

•

•••••••••

Sirius™ Multigas DetectorThe Sirius Multigas Detector provides users outstanding multifunctional capabilities by integrating a high-performance PID (Photoionization Detector) sensor into a 4-gas detector. Users are able to simultaneously monitor for volatile organic compounds (VOCs) with low vapor pressures while measuring for combustible, toxic, and oxygen-deficient atmospheres within one reliable, easy-to-use, durable unit. MSA’s own proprietary PID sensor design provides users with excellent PID performance including humidity resistance, stable zero readings, and fast response and clear times.

Approvals and Standards: UL, CSA (pending), ATEX (pending)

Hazards: Combustible atmosphereConfined spaceOxygen deficiencyToxic atmosphere IDLHToxic atmosphere Non-IDLH

Applications: Chemical, Domestic Preparedness, Fire Fighting, Gas Detection, General Industry, Hazardous Materials, Oil and Gas, Spray Painting, Telecommunications, Water/Wastewater

Priced from $2,995.00

•

•••••

•

MultiRAE Plus PGM-50The MultiRAE can be configured from a simple, inexpensive Oxy-gen/LEL monitor all the way to an affordable five-gas monitor for total protection in toxic environments. Easily reconfigured and upgraded, MultiRAE’s versatility allows it to replace a wide range of monitors, saving training and maintenance costs. The MultiRAE can be quickly and easily changed from a sophisticated technician instrument to a simple text or display-only monitor. The same monitor can be used as personal monitor, a hand-held sniffer, or area monitor for industrial hygiene work, emergency response or confined space entry.

Compact and lightweight for use in tight confined spacesEasy one-button calibration with auto-zero capabilityRuns on alkalines, NiCd batteries, or continuously when plugged into charger or optional 12V automotive adapterAvailable as diffusion unit or with internal sample draw pumpInternal pump provides quick response and remote sampling with 10-12 hours of run timeProgrammable alarms can be changed on the MultiRAE or from (Optional) easy to use Windows® softwareInternal memory holds response factors for 37 common LEL gases and 60 common VOCs (with ability to program custom factors)

Listed below are the most popular configurations, many other configura-tions are available.

Item Description Price009-3121-010 MultiRAEPlusO2/LEL/H2S/CO/PID $3,485.00009-3121-014 MultiRAEPlusO2/LEL/H2S/CO/PIDKit $4,185.00009-3891-010 MultiRAEPlusO2/LEL/NH3/PH3/PID $3,885.00

•••

••

•

•


MUL

TI-G

AS -

PLUS

–

INSTR

UM

EN

TS iTX Multigas Monitor

Monitors from one to six gasesSimplified “Quick-Cal” feature24-hour runtime with lithium-ion batteriesDatalogging capability standardLifetime warranty

The iTX is the industry’s most versatile portable gas detection instrument. Designed to grow with you as your monitoring needs change, the iTX can go from being a single-gas unit to a six-gas monitor, or any-thing in between. Featuring “smart” sensor technology, the iTX provides simplified, single-button operation and calibration functions. A Quick-Cal feature quickly calibrates up to four sensors at once, saving time and calibration gas costs.

The iTX features a backlit dot matrix LCD that simultaneously displays all gases monitored, ultra-bright visual alarms, and a powerful 90 dB audible alarm, all encased in a compact, rugged stainless steel housing to provide maximum durability and RFI protection.

Item Description Price18104307-11014 iTX,LEL,O2,H2S,CO,Li-ion $1,785.0018104307-11100 iTX,LEL,O2,CO,Li-ion $1,535.0018104307-11400 iTX,LEL,O2,H2S,Li-ion $1,535.0018104307-11126 iTX,LEL,O2,CO,NO,NO,Li-ion2 $2,210.0018104307-1147A iTX,LEL,O2,H2S,Cl2,ClO2,Li-ion$2,210.0018104307-1145A iTX,LEL,O2,H2S,SO2,ClO2,Li-ion$2,210.0018104307-11457 iTX,LEL,O2,H2S,SO2,Cl2,Li-ion $2,135.0018104307-11347 iTX,LEL,O2,NH3,H2S,SO2, Cl2,Li-ion $2,210.0018105551-AB+ DS2InstrumentDockingStation foriTX $1,795.0018104646 iSPMotorizedSamplingPump $398.0018105189 iTXConstant-FlowHandPump $149.0018104729 iButtonProgrammingKit,120VAC $295.0017096348 iButtonDataMemoryCell w/MountingCard $24.9517090333 iButtonDataMemoryCell $7.9518104737-120 iTXChargerw/DataloggingKit, 120VAC $445.0018104711-120 iTXCharger/Datalink,120VAC $375.0018104315 iTXSingle-UnitCompactCharger, 120VAC $79.0018105296 iTXSingle-UnitCompactCharger, 12VDC $79.0018105379 6-UnitChargerw/FlyingLeadsand CradleforiTX $350.0018104703 iTXLeatherCarryingCase $75.00

+ Ordering information – A = Wireless Compact Flash (0-none, 1-installed +$125.00)B = number of iGas Readers at $45.00 each

•••

••

SentryRAEThe SentryRAE is the first “lunchbox” – sized, portable, pumped monitor to combine a PID and standard four gas confined space monitor in one product that can run over 24 hour on either rechargeable Lithium-ion or alkaline batteries.

O2, LEL, PID and any two plug-in “smart”

toxic sensors: CO, H2S, SO

2, NO, NO

2, Cl

2,

HCN, NH3, PH

30-2,000 ppm measurement of VOCs (volatile organic com-pounds) with 0.1 ppm resolution

•

•

MX6 iBrid™ Multi-Gas MonitorThe World’s First Gas Monitor with a Color Display

1 to 6 gas monitorFull-color LCD displayUp to 40 hours with extended runtime batterySimple, menu-driven navigation25 available sensorsDiffusion or internal pump operationDS2/iNet™ compatible

The MX6 iBrid™ is the new full featured multi-gas monitor from Industrial Scientific. The user-friendly design of the MX6 features a full-color liquid crystal display and 5-way navigation button to scroll through the menu-based operating system. Designed to meet a variety of monitoring applications, the iBrid™ can be set up to detect from 1 to 6 gases, including options for PID and infrared sensors for combustible gases and Carbon Dioxide. Configured with an internal sampling pump or for diffusion operation, the MX6 is ideal for applica-tions from confined space entry to personal survey monitoring.Confined space kit includes: monitor, motorized sampling pump/tubing, universal charger, carrying case, belt clip, calibration gas/regulator/cup/tubing, wrist strap, maintenance tool, manual, quick start guide, Training CD.

Item Description PriceMX6-K1230101 LEL,CO,H2S,O2,Li-Ion,Diffusion $1,760.00MX6-K0230101 LEL,H2S,O2,Li-Ion,Diffusion $1,510.00MX6-K1030101 LEL,CO,O2,Li-Ion,Diffusion $1,510.00MX6-K0030101 LEL,O2,Li-Ion,Diffusion $1,260.00MX6-K1230301 LEL,CO,H2S,O2,Alk,Diffusion $1,690.00MX6-K0230301 LEL,H2S,O2,Alk,Diffusion $1,440.00MX6-K1030301 LEL,CO,O2,Alk,Diffusion $1,440.00MX6-K0030301 LEL,O2,Alk,Diffusion $1,190.00MX6-K1230211 LEL,CO,H2S,O2,Li-Ion/ER,w/Pump$2,035.00MX6-K123R211 LEL,CO,H2S,O2,PID, Li-Ion/ER,w/Pump $2,460.00MX6-K103Q211 LEL,CO,O2,CO2,Li-Ion/ER,w/Pump$2,180.00

Confined Space Kits MX6KIT-K1230211 4-gasw/Pump $2,760.00MX6KIT-K123R211 4-gas/PIDw/Pump $3,335.00

Accessories 18107094 BatteryCharger/Datalink $295.0018107011 BatteryCharger,12V $79.0018106765 SP6MotorizedSamplingPumpModule$250.0018106724-ABC* DS2InstrumentDockingStation $1,795.00

*Order with appropriate suffix. A. Wireless Compact Flash (-0 None, -1 Installed +125.00 $USD) B. iGas Reader (-0 None, -1 +45.00 $USD, -2 +90.00 $USD, -3 +135.00 $USD) C. Power Cord (-0 (N.American Plug), -1 (UK Plug), -2 (European Plug), -3 (Australian Plug))Supplied with monitor: universal charger, nylon carrying case, belt clip, calibration cup/tubing, wrist strap, maintenance tool, manual, quick start guide, Training CD, dust filter water stop (aspirated unit only).

•••••••

Over 60 Correction Factors built into the SentryRAE memory and the largest printed list of Correction Factors in the world (300+),RAE Sys-tems offers the ability to accurately measure more ionizable chemicals than any other PID! Drop-in battery Strong, built-in sampling pump Large key and easy-to-read display with backlight Store up to 80 hours of data Loud audible alarm and extra-bright light Rugged, weather-resistant housing

Item Description Price040-3121-002 SentryRAE $4,245.00

•

••••••


INSTR

UM

EN

TS – M

ULTI-GAS - PLUS

950 Series Multi-Gas DetectorsEasy to use, 3-button operation makes the 950 series practical and depend-able on the job. The ergonomically designed, high-impact case will take the wear of heavy use. The water resis-tant unit offers pump or diffusion air sampling methods. Sensor Options: oxygen, combustible, carbon monoxide, hydrogen sulfide, ammonia, chlorine, hydrogen cyanide, hydrogen, sulpher dioxide, nitrogen dioxide, nitric oxide, chlorine dioxide, phosphine, solid state-MOS for toxics.

5 Interchangeable Plug & Play Sensors Exchange sensors without calibration 103 - dB Alarm Large LCD display for easy reading Rechargeable or Alkaline battery operation Data-logging optionEasy to change configuration Lifetime electronic warranty option 28+ hour run time Special Cal Gas Kit pricing when ordered with monitor

Standard equipment include: 16-ft tubing, Cal Hood, Software for Ex-panded Internal Settings, Manual.Item numbers listed are sold calibrated to Methane.

Item Description Price950-A100-MABCZ 950A100basewithAlkalinebatteryand

EX/OX/CO/HSsensors $1,895.00950-A101-MABCZ 950A100basewithAlkalinebatter,pump

andEX/OX/CO/HSsensors $2,159.00950-A111-MABCZ 950A111basewithAlkalinebattery,pump

dataloggingandEX/OX/CO/HS $2,240.00950-R111-MABCQ 950R111withNiMHbattery,pumpdata

loggingandEX/OX/CO/HS/PID,10.6eVsensors (EXcalibratedtoMethaneandPIDto Isobutylene) $3,999.00

••••••••••

Draeger X-AM 7000 Multigas Monitor The X-AM 7000 can be fitted with three electrochemical and two infra-red optical or catalytic sensors, and can simultaneously measure up to five gases. A choice of over 25 sensors allows detection of more than 100 gases and vapors. Not only dust and splash-proof, but also completely water-resistant with an ingress protection rate IP67. Water-repellent membranes protect the sensors if they are dropped into water. Rechargeable batteries offer a long battery life. The high-delivery pump can draw in sample gas through a hose up to 150 ft / 45 meters in length.

Provides flexible gas monitoring with a wide range of sensor selection. All sensors are intelligent and are recognized automatically by the instrument (plug & play). The smart sensor technology allows different types of data (gas identification, alarm functions, measurement data), to be stored in the EEPROM inside the sensor. The sensors are pre-calibrated and easily replaced by the customer. The Dräger X-am 7000 can accept catalytic sensors and infrared sensors as well as the Draeger XS sensor series.

When the instrument is in leak detection mode, a ppm bar graph appears on the display, showing the changes in concentration in steps of 50 ppm. The instrument generates ascending or descending tone frequencies – similar to a Geiger counter – which reflect the detected gas concentra-tion. In an alarm situation the Draeger X-AM 7000 automatically returns to its normal operating mode.UL approved as Class I, Div 1, Group A, B, C and D. It can be used in a temperature range from -20 to +60 °C.Ideal for monitoring waste/water, oil and gas, chemicals and offshore industries.

Please call for pricing and availability on the configuration you need.

5-in-1 Gas Monitor with Pump (GX-2003)

Monitors LEL, O2, H

2S, CO

Monitors 100% Vol. Methane with TC sensorAuto ranging display of % Vol. or %LELInternal sample drawing pump with 40-feet Calibration reminder and lock outNi-Cad or alkaline power sourceBattery pack recharges in 90 mins.Up to 600 hours of datalogging with alarm STEL and TWA readouts

Item Description Price72-0281RKC 5sensor,%Vol(HC),LEL,O2,CO,H2SwithNi-MH batterypackand115VACcharger $1,475.0072-0271RKC 4gas,LEL,O2,CO,H2SwithNi-MHbattery packand115VACcharger $1,325.0072-0251RKC 3gas,LEL,O2,COwithNi-MHbatterypackand 115VACcharger $1,225.0072-0270RK 4gas,LEL,O2,CO,H2Swithalkalinebatteries $1,195.0072-0250RK 3gas,LEL,O2,COwithalkalinebatteries $1,095.00

••

••••••


MUL

TI-G

AS -

PLUS

–

INSTR

UM

EN

TS

The Cannonball3 One button gas detection with a memory! The Cannonball3 is designed to stand up to the harshest environ-mental conditions while delivering quality. The Cannonball3 can be config-ured to monitor oxygen, combus-tible gases and vapors and many toxic gases. With Biosystems’ “Duo-Tox” sensor installed, the Cannonball3 can simultaneously detect up to 5 different gases. It is also available in the PPM hydrocarbon configuration. The Cannonball3 is housed in a durable impact-resistant case that is completely sealed from the outside elements. Three different LED alarm lights guarantee that visible alarms can be seen from any angle. The graphics display is the largest in its class, making it easy to read from a distance. All procedures necessary for day-to-day operation, including fully automatic calibration adjustment, are controlled through a single button. Instrument configuration options and other higher functions are accessed with the four navigation arrows on the top of the instrument. Available in either rechargeable (NiMH) or disposable alkaline battery versions. The NiMH version will provide at least 16 continuous hours of operation even with the display back light continuously on. The Alkaline version will provide at least 24 hours of continuous operation in similar conditions. Standard Accessories: Each Cannonball3 detector is shipped complete with probe assembly including 10 feet of tubing, reference manual, shoul-der strap and probe and instrument filter replacement kits. Rechargeable detectors include battery charger and internally-housed nickel metal hydride (NiMH) battery pack.

Item Description Price54-34-30100N RechargeableNiMHversion $2,725.0054-34-30100A DisposableAlkalineversion $2,525.0054-34-31400A LEL/O2/Duo-Tox(CO/H2S)Alkaline $2,635.0054-34-31400N LEL/O2/Duo-Tox(CO/H2S)NiMH $2,835.00

Biosystems PhD5 Introducing the ultimate in confined Space Gas DetectorsThe PhD5 monitors up to five atmospheric hazards simultaneously: oxygen, combustible gas and up to three channels of toxic gas detection. The in-novative new Duo-Tox two-channel CO/H

2S

sensor to measure both carbon monoxide and hydrogen sulfide when both hazards are present without cross interference. The PhD5 has a rugged, metal-plated case, while allowing for easy one-button keys and clear display making easier than ever to use. Can be or-dered with or without the Touch-ID automatic memory download system. The Touch-ID kit allows you to store user ID and location information for the environment being monitored. Good recordkeeping at the touch of a button is critical to your confined space program. The PhD5 can be ordered in a variety of configurations.

The unit listed below comes equipped as follows: Complete Confined Space Kit: Comes complete with foam-carrying case, calibration gas, regulator, fittings and reference manual, quick reference card and training video. Alkaline battery pack and set of 3 AA disposable batteries. Popular configurations listed below.

Item Description Each54-24-30100A PhD5,withLELO2/COsensors $1,307.0054-24-30200A PhD5,withLELO2/H2Ssensors $1,370.0054-24-30102A PhD5,withLELO2/CO/H2Ssensors $1,645.0054-24-31400APhD5,withLELO2/Duo-ToxCO H2Ssensors $1,480.0054-24-31403A PhD5,withLELO2/SO2, Duo-ToxCO/H2Ssensors $1,810.0054-27-0101 Motorizedcontinuoussamplepump $435.0054-27-0802 TouchIDprogrammingkit $210.00

Eagle™ One To Six Gas Portable Sample Drawing Monitor The EAGLE is a powerful instrument that does more than offer standard confined space protection. The EAGLE also provides detection combinations never before offered in a portable gas monitor featuring the industry’s widest selection of high quality, long life and field proven sensors.

The EAGLE’s ergonomic design offers easy access to controls such as autocalibration, alarm silence, de-mand zero, peak hold and a wide variety of other features. Each channel has 2 alarm levels plus TWA and STEL alarms for toxic channels. Alarm levels are adjustable and can be latching or self resetting.

Standard features on the EAGLE are not available on most other competitive units such as PPM/LEL hy-drocarbon detection (5 ppm resolution) and a methane elimination switch for environmental applications. For quick response and recovery, the EAGLE has a strong internal pump which can draw samples from over 125 feet. The EAGLE will continuously operate for over 30 hours on alkaline batteries or 18 hours on Ni-Cads. Many accessories such as long hoses, special probes, datalogging, continuous operation adapters, remote alarms and strobes, dilution fittings, internal hydrophobic filter, etc, are available to help satisfy almost any application. Rugged, weather resistant, easy to operate and maintain, the EAGLE is the industry’s answer to portable gas detection in many applications, including land survey. The EAGLE can be provided with up to 6 gas sensors (4 Toxics maximum). Please specify gas combination when ordering.

Please call 800-MALLORY for the complete list of configurations and calibration kits. Need replacement parts, we can supply those too!


INSTR

UM

EN

TS – M

ULTI-GAS

Solaris® Fire Multigas DetectorChoose a world-class instrument that is durable and provides the best value in its class. Detects the presence of O

2, H

2S, CO and Combustible

gas with state-of-the-art engineering and quality. Whether you need just the instrument or a complete deluxe kit you can have it any way you want. An Assemble-To-Order System is available to configure the instrument just how you need it. You can select from sensors, power supply, datalogging, calibration acces-sories and more. We are listing some basic standard choices below. All kits include: configured, non-data-logging, UL/cUL approved Solaris Fire instrument with charger, calibration cap assembly, instruction card and manual, durable stowable red carrying case and orange instrument case - at no additional cost.

Item Description Price10055775 DeluxeKit(includes4-gasinstrument samplingpumpandecon-calcalibrationkit) $1,544.0010055773 StandardKit(includes4-gasinstrument andsamplingpump) $1,244.0010055774 StandardKit(includes4-gasinstrument andecono-calcalibrationkit) $1,215.0010055772 BasicKit–instrumentonly $915.0010050976BeltClipRetractableLanyard $47.00

Solaris™ Multigas DetectorWithstands rough handlingThe Solaris Multigas Detector is an affordable, durable, reliable, easy-to-use portable instrument for detecting the presence of O2, H2S, CO and combustible gas.

One-button calibration Long-life batteryCarbon-filled nylon case Built-in pumpTough construction and durable sensorsTIM® System compatibilityLink™ Software compatibility

Item Description Price10048148 4-gasinstrument $825.0010048150 3-gas(LEL,O2,CO) $755.0010048211 3-gas(LEL,O2,H2S) $755.0010048213 2-gas(LEL,O2) $685.00

Standard Kits (includes datalogging option) 10048147 4-gasinstrument $825.0010048149 3-gas(LEL,O2,CO) $755.0010048212 3-gas(LEL,O2,H2S) $755.0010048214 2-gas(LEL,O2) $685.00

Industrial Kits (includes calibration kit)

10049293 4-gasinstrument $1,125.0010049294 3-gas(LEL,O2,CO) $1,055.0010049295 3-gas(LEL,O2,H2S) $1,055.00

Deluxe Kits (includes calibration kit, datalogging, and sampling pump)

10049297 4-gasinstrument $1,454.0010049298 3-gas(LEL,O2,CO) $1,384.0010049299 3-gas(LEL,O2,H2S) $1,384.0010049300 2-gas(LEL,O2) $1,314.00

•••••••

M40 Multi-gas Monitor

1 to 4 gas monitoring for O

2, LEL, CO, H

2S

Standard vibrating, 90 dB audible and ultrabright visual alarms18-hour runtime with integral Li-ion battery packLow, High, STEL, and TWA user- adjustable alarmsStandard 75-hour datalogging capabil-ityTwo-year all-inclusive warranty

Built with the durability and simplicity found in every Industrial Scientific instrument, the M40 is a reliable, low-cost gas monitoring solution for confined space or personal monitoring applications. The M40’s rugged composite case is immune to RFI, and houses four discrete sensors, a large LCD readout, and integral lithium-ion battery for up to 18 hours continuous runtime.

The M40 continuously monitors oxygen, combustible gases, carbon monoxide, and hydrogen sulfide in any combination, activating bright alarm light, 90-dB audible, and internal vibrating alarms when gas con-centrations exceed the preset limits. Additional standard features include Peak/Hold functions, STEL and TWA readings, a continuous loop datalogger and ‘Quick-Cal’ calibration.

The M40 comes standard with a charger, nylon carrying case, cell-phone belt clip and calibration cup with tubing. Available accessories include SP40 motorized remote sampling pump, 12 VDC automobile charger, M40 datalink and M-Cal Calibration Station.

Item Description Price18105437-01111 M40Monitor–LEL,O2,CO,H2S $595.0018105437-01101 M40Monitor–LEL,O2,CO $545.0018105437-01110 M40Monitor–LEL,O2,H2S $545.0018105437-11111 M40/SP40–LEL,O2,CO,H2S $745.0018105437-11100 M40/SP40–LEL,O2,CO $695.00M40-KIT-11111 M40ConfinedSpaceKitw/pump LEL,O2,CO,H2S $1,150.00M40-KIT-11101 M40ConfinedSpaceKitw/pump LEL,O2,CO $950.0018105460 SP40MotorizedSamplingPump $150.0018105510 6-unitCharger $375.0018105502 12VDCAutomobileCharger $49.0018105528 M40Datalink $150.0018105965-100 Single-UnitM-Cal,M40Bay $795.0018105965-010 Single-UnitM-Cal,M40/SP40Bay $795.00

•

•

•

•

•

•

Great Service is just a phone call away1 -800-MALLORY


MUL

TI-G

AS –

IN

STR

UM

EN

TS

QRAE IIThe QRAE II is a compact multi-gas detector for H

2S, CO, O

2, and combustibles.

Key features include externally accessed battery packs, a water-resistant case and state-of-the-art O

2

sensor technology with extended life.One to four plug-in sensors (combustibles, oxygen SPE O2™, hydrogen sulfide, carbon monoxide)Diffusion mode, with optional manual sample pumpIntuitive simple-to-operate two-button user interfaceDisplay can be flipped 180º with the push of a button for easy viewing from belt or handMulti-language supportOne-button calibration with auto-zero capabilityLoud 95dB audible alarmBright red flashing visible alarmVibration alarmInterchangeable drop-in Lithium-ion and alkaline battery packsCharging cradle doubles as an external battery chargerCompatible with AutoRAE calibration stationOptional Confined Space Entry Kit

Item Description Price020-0401-000 QRAEII $645.00

•

•

••

•••••••••

EntryRAEThe typical confined space monitor measures oxygen, combustibles, carbon monoxide, and hydrogen sulfide. Will it keep you safe in today’s industrial environment? No.When doing confined space work today, you need the added broadband protection of a PID.

The EntryRAE is a 4-gas monitor, plus pho-toionization detector (PID). Reliable, easy to operate, and simple to calibrate, the EntryRAE delivers added protection without added com-plexity. Combine a PID and a 4-gas monitor and you have true protection from the unexpected.

Reliable, self-cleaning VOC detectorAlso includes CO, H

2S, LEL, and O

2 sensors

Simple to operate and easy to calibrateData logging included - and automaticBright red flashing LED alarms and loud audible alarmsUp to 16 hours of continuous operationCharging cradle doubles as an external battery chargerPowerful pump allows sample-draws up to 100 feet (30 meters)Low-flow pump alarm

Item Description PriceStandard sensor configurations pgm-3000

046-P000-100 Unitonly $1,195.00046-P000-101 UnitwithCSKII $1,390.00

Call for more information on ordering and accessories

•••••••••

QRAE PlusThe QRAE Plus is a full-fea-tured, compact, one-to-four sensor confined space gas detector. Its fea-tures include easy-to-change, externally accessed battery packs (available in both alkaline and rechargeable versions) and water-resistant case design. The rechargeable, Lithium-ion battery pack provides up to 20 hours of continuous operation. The QRAE Plus includes 16,000 datalogging points of storage capacity for download to PC compatible with Windows 98, NT, 2000, and XP.

One-to-four plug-in “smart” sensors: Combustible, Oxygen, Hydrogen Sulfide, Carbon MonoxideOptional substance-specific toxic sensors: Sulfur Dioxide (SO

2), Nitric

Oxide (NO), Nitrogen Dioxide (NO2), Chlorine (Cl2), Hydrogen

Cyanide (HCN), Ammonia (NH3), Phosphine (PH

3)

Rechargeable Lithium-ion battery pack provides up to 20 hours (more than 2 work shifts) of continuous operationRugged housing withstands use in harsh environments with a water- and dust-resistant case and strong protective rubber bootHighly resistant to radio frequency and other electromagnetic interfer-enceStrong, built-in sample draw pump with optional collapsible sample-probeAlso available in diffusion configurationOne-button calibration with auto-zero capabilityLoud audible alarmBright visual alarmInterchangeable Lithium-ion and alkaline battery packs

ApplicationsConfined space entryWaste water treatment plantsMarine and off-shore oil wellsLandfill operationsTrenches, silos, railcarsCoal minesSewers and manholes, tunnelsRefineries and petrochemical plants, including off-shore drilling and plant shut downsPower plantsPulp and paper industrySteel mills

These are the most commonly purchased QRAE PLUS monitors, with a universal charger and an international plug kit. For other configurations, please ask us for a configurator chart.

Item Description PriceStandard Sensor LEL/O2/H2S

028-1101-010 LEL/O2/H2SUnitonly $910.00028-1101-011 UnitwithAccessorieskit (nogasorregulator) $1,135.00028-1101-014 UnitwithAccessoriesand CalibrationKit $1,360.00

Standard Sensor LEL/O2/CO 028-1102-010 Unitonly $910.00028-1102-011 UnitwithAccessoriesKit (nogasorregulator) $1,135.00028-1102-013 UnitwithAccessoriesand CalibrationKit $1,240.00

Standard Sensor LEL/O2/H2S/CO 028-1112-010 Unitonly $1,105.00028-1112-011 UnitwithAccessoriesKit (nogasorregulator) $1,330.00028-1112-012 UnitwithAccessoriesand CalibrationKit $1,555.00

•

•

•

•

•

•

•••••

••••••••

•••


INSTR

UM

EN

TS – M

ULTI-GAS

QRAE- |Multi-Gas Monitors The QRAE is a dedicated confined space entry monitor with an internal pump. Its durable, rechargeable, standard Lithium-ion batteries provide a 12-hour day of detecting combustibles, oxygen, hydrogen sulfide, and carbon monoxide. The extended duration Lithium-ion battery option provides up to 18 hours of continuous operation.

Key FeaturesReliable plug-in “smart” sensors: Combustible, Oxygen, Hydrogen Sulfide, Carbon MonoxideRobust external casing for harsh environments, including a strong protective rubber boot, water and dust resistance, rugged ABS plastic/metal case, and protection from portable radio interference (RFI)Ease of use with one-hand operation; one-button calibration with auto zero capabilityStrong built-in sample draw pump, with a flow rate at 150cc/min and (optional) collapsible remote sampling probe, prevents liquid flow into monitor, and its patented security mechanism warns of sample tube crimping or blockageOption of Li-ion, alkaline, and automotive 12V adapter chargerField replaceable batteriesUnit will run and charge simultaneouslyLarge keys are operable even with three layers of glovesLoud audible alarmBright visual alarmStandard 20,000 point (or 100 hours) datalogging storage capacity for download to PC (compatible with Windows 98, NT, 2000, and XP)

ApplicationsConfined space entryWaste water treatment plantsMarine and off-shore oil wellsLandfill operationsTrenches, silos, railcarsCoal minesCruise shipsSewers and manholes

Item Description-Model PGM-50Q Price027-0000-010 QRAE4-gas,pump,datalogging, Li-ionbattery,120Vwalladapter $695.00027-0000-011 QRAE4-gas,pump,datalogging,Li-ionbattery, 120walladapter,ConfinedSpaceKit $875.00027-0000-110 QRAE4-gas,pump,datalogging, Li-ionbattery,230Vwalladapter $695.00027-0000-111 QRAE4-gas,pump,datalogging,Li-ionbattery, 230Vwalladapter,ConfinedSpaceKit $875.00

•

•

•

•

•••••••

••••••••

740 Series Portable Multi-Gas DetectorSpeed, reliability, flexibility and affordability are what you’ll get.

Precalibrated Sensor Pack switch and go in seconds, no more delaysSensor Tester, push-of-the button easeLi-Ion battery delivers up to hours of run time. (optional - 3 AAA Alkaline)Massive data logging capacity stores more than five months’ recordsBanshee Alarm is the loudest in the industryRated Class 1, Division 1

Standard features include: rechargeable Li-ion battery. charger adapter, internal vibrator, data logging, rugged alligator clip, infrared port, gas test hood, and instruction manual.

Available with a variety of options: sensors for oxygen, carbon monoxide, hydrogen sulfide and combustibles.Item numbers listed are sold calibrated to Methane.

Item Description Price740-100-400 7404-gasmonitorwithH2S,OX,CO,EX;

alligatorclip,rechargeableLi-ionbattery,Universal powersupply(100-240VAC)Calgashoodand tubing,quickstartmanual,CDmanual $699.00

740-100-300 7403-gasmonitorwithOX,CO,EX; alligatorclip,rechargeableLi-ionbattery,Universal powersupply(100-240VAC)Calgashoodand tubing,quickstartmanual,CDmanual $679.00

740-100-350 7403-gasmonitorwithH2S,OX,EX; alligatorclip,rechargeableLi-ionbattery,Universal powersupply(100-240VAC)Calgashoodand tubing,quickstartmanual,CDmanual $679.00

740-100-200 7402-gasmonitorwithOX,EX;alligatorclip, rechargeableLi-ionbattery,Universalpowersupply (100-240VAC)Calgashoodandtubing, quickstartmanual,CDmanual $655.00

•••

•••

Call 1-800-MALLORY for more for more information

Mallory Rental & Repair Center Rental, Repair and Sales of Gas Detectors, SCBA’s, Air Lines and More

REPAIRFast TurnaroundLow RatesKnowledgeable Technicians

•••

RENTDay, Week or Monthly Rental Top Quality Equipment Convenient Pickup and Free Delivery for Rentals of 5 or More Units Great Rates

•••

BUYGenerous Trade-In Programs Easy Demo ProgramTop Quality Equipment Expert Advice to Help You Make the Right Choice

••••


MUL

TI-G

AS –

IN

STR

UM

EN

TS

RKI GX-2003 Multi Gas 5-in-1 MonitorBuilt around high-quality micro-sensor technol-ogy, the GX-2003 is RKIs smallest personal 5-in-1 gas monitor with a built in sample pump. Weighing only 11 ounces, it has many features, which set the GX-2003 apart from the competition. For example, it can monitor the standard confined space gases (LEL com-bustibles, Oxygen content, Carbon Monoxide, and Hydrogen Sulfide), and it can also measure 100% volume Methane and dynamically display either % LEL, or % volume with its auto-ranging ability.

The GX-2003s large LCD display shows all gas readings, battery level, current time, and will automatically backlight in alarm conditions. This unit also has a special bar hole mode to facilitate locating underground gas leaks. A high sensitivity leak check mode is also included, and provides ppm level detection of gas leaks. A special variable frequency alarm helps to pinpoint the leak without looking at the instrument display. Other standard mode alarm types include vibration, visual, and audible alarms that can be set to latching or non-latching. Controlled by a microproces-sor, the GX-2003 continuously checks itself for sensor connections, low battery, circuit trouble, low flow, and calibration errors. The GX-2003 can interchangeably operate on either a Ni-MH battery pack or 3 AA alkaline batteries. The batteries are simple to replace requiring no tools to access the battery compartment. The Ni-MH battery pack can receive a charge directly within the instrument or separately, allowing the unit to remain in service.

Calibration intervals and reminders are user adjustable and can be set to either go into alarm or to lock the user out of normal measurement mode once a calibration period has expired. Calibrations can be performed automatically or individually in single calibration mode. The GX-2003 is also compatible with the economical SM-2003 single channel calibration station.

FeaturesThree operating modes: Normal, Bar Hole, and Leak CheckMonitors LEL, and % volume methane, O2, and CO (optional H2S)Barhole mode tests for peak methane and oxygen levelsLeak detect mode offers high sensitivity tests for ppm level natural gas leaks0 to 100% volume MethaneAuto-ranging display of % volume and % LELInternal sample drawing pump with up to 40’ rangeVibration, visual, and audible alarmsAutomatic backlight during alarmsCalibration reminder with lock out optionNi-MH or alkaline power source (interchangeable)Quick charge (complete charge in 90 minutes)Glove friendly glow in the dark buttonsAlarm latching or non-latchingHigh impact protective rubber bootUp to 600 hours of datalogging with alarm trendsAutocalibration or single calibrationTWA and STEL readings with lunch-break modeIntrinsically safe, CSA, C/US classified2-year warranty

ApplicationsUtilities, Personal monitoring, Confined space entry, Refineries and petrochemical, Chemical plants, Hazardous material, Water and waste-water treatment, Fire services, Mining

Please call for pricing and information.

••••

••••••••••••••••

•

RKI GX-2001 Multi Gas 4-in-1 MonitorRKI is proud to introduce the smallest and most affordable 4-gas monitor in the world, the GX-2001. Weighing only 6 ounces and about the size of a pager (2.8” H x 2.2” W x 1.1” D), the GX-2001 simultaneously monitors combustibles, oxygen, carbon monoxide, and hydrogen sulfide. The GX-2001 is armed with standard features like autocalibration, datalogging, rechargeable Ni-MH batteries, a unique vibration alarm, STEL / TWA readings, peak hold and auto backlighting at alarm on a large LCD display, and it even tells the time. All of these controls and features are operated through 3 sim-ple glow in the dark buttons. Utilizing either of the GX-2001’s chargers, the standard charger or datalogging / charger station, it’s Ni-MH batteries will fully recharge in 90 minutes. Also available is the datalogging software program, which is Windows 95, 98, ME compatible.

The GX-2001 is also designed around the world’s smallest gas sensors. Utilizing catalytic combustion, electrochemical and galvanic sensor tech-nologies, each miniaturized sensor is manufactured with the same high quality control that has made Riken sensors and instruments the most reliable and long lasting monitoring devices in the industry.

FeaturesSimultaneous detection of 4 gases: LEL, O2, H2S, & COSmallest 4-gas monitor on the market: 2.8” H x 2.2” W x 1.1” D, 6 ozVibration alarmAlarm trend dataDatalogging standardAutocalibrationNi-MH batteries recharge in 90 minutesContinuously operates for up to 18 hoursLarge LCD display screenAutomatic backlighting at alarmHigh impact, RFI shielded bodySTEL and TWA readoutsPeak hold readoutsContinuously displays current timeIntrinsically safe, CSA, C / US approved2 year warranty

Item Description Price72-0233RKC 4gas,LEL/O2/H2S/CO withbeltclip,with115VACcharger $795.0072-0231RKC 3gas,LEL/O2/COwithbeltclip, with115VACcharger $745.0072-0232RKC 3gas,LEL/O2/H2Swithbeltclip, with115VACcharger $745.0072-0233RK 4gas,LEL/O2/H2S/CO withbeltclip,nocharger $745.00

••••••••••••••••


INSTR

UM

EN

TS – M

ULTI-GAS

PhD LiteTop-shelf performance!This durable confined space gas detec-tor will monitor up to four atmospheric hazards simultaneously; oxygen, combus-tible gas, carbon monoxide and hydrogen sulfide. Requires three AA Alkaline batteries to power unit for nine hours. The rugged, metal-plated case is designed to withstand demanding environments. Single button con-trols necessary procedures, including calibra-tion. Each unit is shipped with hand-aspirated sample draw kit with 10’ of tubing, reference manual, quick reference card, belt clip and three AA batteries.

Item Description Each54-23-300AV PhDLite,LEL/O2sensors $1,132.1154-23-301AV PhDLite,LEL/O2/COsensors $1,415.9454-23-302AV PhDLite,LEL/O2/H2Ssensors $1,587.1254-23-314AV PhDLite,LEL/O2dualchannel H2Ssensors $1,700.84

Draeger X-AM 3000Dräger XAM 3000 is an innova-tive 3- or 4-gas warning-device. This small and lightweight in-strument reliably monitors H

2S,

CO, O2 and combustible gases

and vapors in ambient air.A large display enables the easy identification of the measured values. The simple 3-button op-eration and an easy-to-use menu ensure intuitive operation.The pre-calibrated electrochemi-cal sensors and the catalytic sen-sor are automatically recognized and provide precise and reliable measuring results.In addition to a very loud audible alarm and a bright visual alarm, a vibrating alarm is integrated in the instrument.A life signal assures full functionality of the instrument without a visual check by the operator. Even if the peak value disappeared before it could get registered, the Dräger XAM 3000 can recall all maximum values. When using a defined gas mixture, the instrument can be calibrated by pressing a single button.An optional internal pump with 33 ft. (10 m) tubing is ideal for confined space applications. A convenient pump adaptor makes is easy to switch between pump and diffusion modes.The X-AM 3000s compact design combined with it’s state-of-the-art electronics, ensures that it is ideally suited for gas detection requirements in all applications and industries.Please call for the model and accessories you require. Many combinations are available.

MultiVision Confined Space Gas Detector The new standard in inexpensive and reliable gas detection The MultiVision offers up to four independent sensors for the detection of oxygen, combus-tible gas, carbon monoxide, and hydrogen sul-fide. The instrument case is made of chrome-plated ABS and is rated to IPX5 / IPX7 against water ingress (immersible) and is rate for RFI immunity to 40 V/m.

The MultiVision offers run times of up to 20 hours in diffusion mode and up to 16 hours when using the internal the pump and NiMH battery pack. Alkaline battery packs yield run times of up to 16 hours in diffusion mode and up to 12 hours with the internal pump on between battery changes.

A single button located on the left side of this compact and very weather-proof instrument controls all day-to-day instrument functions.

Item Description Price54-40-30100A Alkaline $807.1054-40-30100N NiMH $1,023.7554-40-30100A LEL/O2/COAlkaline $745.0054-40-30102A LEL/O2/CO/H2SAlkaline $895.0054-40-30102N LEL/O2/CO/H2SNiMH $1,095.00

MultiPro™ Multi-Gas DetectorsBiosystems introduces its smallest con-fined space detector — the MultiPro.™ The MultiPro offers real-time readings for up to 4 gases, true one-button operation (including calibration), and a built-in event logger capable of storing information for 20 events including sensor type, max and average readings, time and duration. It’s available with either a Li-Ion or an Alkaline battery pack and offers run times up to 22 hours. For remote sam-pling, both manual and motorized sample draw kits are available.

Standard Kit includes: Clothing clip, reference manual, and laminated quick reference cardRechargeable Li-Ion version includes charger, calibration adapterTraining CD-ROM

Confined Space Kit includes:All standard accessories, plus: standard sized (58 or 103 liter) cylinder of all-in-one calibration gas, fixed flow regulator with gauge, foam-lined waterproof carrying case

Value Kit includes:All standard accessories, plus: compact sized (34 liter) cylinder of all-in-one calibration gas, fixed flow regulator and foam-lined carrying case.NOTE: PRICES LISTED FOR ALKALINE BATTERY, if you need Li-Ion, please ask for quote. Many accessories and sensors, charging units and datalogging acces-sories are readily available.

Sensors Std Confined ValueItem Installed Kit Space Kit54-48-300 LEL/O2 $445.00 $595.00 $885.0054-48-301 LEL/O2/CO $545.00 $695.00 $1,045.0054-48-302 LEL/O2/H2S $545.00 $845.00 $1,165.0054-48-314 LEL/O2/Duo-Tox (CO/H2S) $575.00 $895.00 $1,195.0054-48-100 LEL $415.00 $565.00 n/a

•••


SING

LE-G

AS –

IN

STR

UM

EN

TS

ALTAIR Pro Detector Gas detectors that really stand out!Innovative ALTAIR Pro toxic gas and oxygen detectors are based on the design of the very popular ALTAIR Single-Gas Detector, but with added features and functionality. These detectors accurately measure the gas concentration or percent oxygen (depending on model) and display this information on a large, clear, backlit LCD. The ALTAIR Pro Single-Gas Detector features superior dust and water protection, excellent impact resistance, great RFI performance, and an extremely effective alarm system. Adjustable alarm set points are offered for LOW and HIGH levels on all units. In addition, the toxic gas versions also have TWA and STEL alarm points. A distinct alarm is indicated by two bright flashing LEDs, a piercing audible alarm, a flashing notification on the LCD, and an internal vibrating alarm, helping to ensure that no alarm condition will go by unnoticed.

With current sensor options for CO, H2S or O

2, the ALTAIR Pro Single-

Gas Detector will provide worry-free performance and stand up to the roughest handling in even the toughest industrial environments. The sensors and battery can easily be replaced to keep the unit performing perfectly for years. Its rubberized armor housing and one-button opera-tion provide the durability and simplicity you expect. The ALTAIR Pro Single-Gas Detector is designed and built with MSA’s superior quality and is part of the MSA STELLAR® Series, which features a varied selection of single-gas and multigas instruments.

Ease-of-use (1-button operation)Distinctive alarm systemAlarm check, bump check, fresh air zero, and calibration made easyEasily-replaceable, commercially-available batteryReplaceable sensorsBuilt-in IR communication (event & data-logging)Rugged design

Please call for pricing and additional information.

Priced from $325.00

•••••••

GasBadge® Pro Dockable Single-Gas Monitor

Interchangeable “smart” sensors moni-tor oxygen or any one of many toxic gasesOne year datalogging capacity (mini-mum)Standard STEL and TWADocking Station™ CompatibleMinimum 2,600 hours continuous op-eration from replaceable CR2 Lithium batteryPPM or % by volume readoutWater resistantLifetime warranty

Built to Industrial Scientific’s highest quality and reliability standards, GasBadge® Pro provides a lifetime of gas hazard protection with more features than any other single-gas monitor available. Interchangeable “smart” sensors enable the GasBadge® Pro to be quickly adapted to moni-tor unsafe levels of oxygen or any one of the following toxic gases: carbon monoxide, hydrogen sulfide, nitrogen dioxide, sulfur dioxide, chlorine, chlorine dioxide, phosphine, hydrogen cyandide and ammonia.

GasBadge® Pro communicates directly via an infrared interface to option-al accessories like the Docking Station™, Datalink, and infrared printer to further simplify and automate calibration, function (bump) testing and data downloading. Standard STEL and TWA readings, and datalogging up to one year of survey data are featured along with an event-logger that records the last 15 alarm events.

Housed in a rugged enclosure, the monitor is immune to RF, water resistant and extremely durable. A protective concussion-proof overmold protects the unit from extreme abuse in a wide variety of harsh industrial environments. Its simple and intuitive four-button navigation allows easy access to setup, operation and calibration functions. Lifetime warranty.

Item Description Price18100060-1 GasBadge®Pro–CarbonMonoxide(CO) $375.0018100060-2 GasBadge®Pro–HydrogenSulfide(H2S) $375.0018100060-3 GasBadge®Pro–Oxygen(O2) $375.0018100060-4 GasBadge®Pro–NitrogenDioxide(NO2) $525.0018100060-5 GasBadge®Pro–SulfurDioxide(SO2) $525.0018100060-6 GasBadge®Pro–Ammonia(NH3) $595.0018100060-7 GasBadge®Pro–Chlorine(Cl2) $525.0018100060-8 GasBadge®Pro–ChlorineDioxide(ClO2) $595.0018100060-9 GasBadge®Pro–Phosphine(PH3) $645.0018100060-B GasBadge®Pro–HydrogenCyanide(HCN) $595.0018106484 GasBadge®ProNylonCarryingCase $10.0018106492 GasBadge®Pro2-unitNylonCarryingCase$15.0018106302-AB+ GasBadge®ProDS2DockingStation™ $1795.0018106500 GasBadge®Constant-Flow HandAspiratedPump $149.0017121963 GasBadge®NeckLanyardw/SafetyRelease$5.0017124504 Replacementwater/dustsensorbarriers(5count) $10.0018106260 GasBadge®Datalink $150.0017117714 Serialdatathermalprinterwith infraredinterface $395.00

+ Ordering information – A = Wireless Compact Flash (0-none, 1-installed +$125.00)B = number of iGas Readers at $45.00 each

•

•

•••

•••


INSTR

UM

EN

TS – SINGLE-GAS

450 Series Single Gas Portable Pocket MonitorIt’s compact size; reliability, competi-tive price and flexibility with nine detector options make the 450 a smart choice.

Built Tough - Rubber boot absorbs everyday impact and pro-tects internal components from dust and water.Superior Warranty - Completely refined inside and out, the 450 Series carries a standard two-year warranty on electronics and sensors CO, H2S, OX, 1 year of toxic sensorsSimple, Informative Display - High contrast numerical level display and high intensity LED alarm warning indication and buzzer effec-tively alert impending gas dangers.Banshee Alarm System - The loudest in the industry at a screaming 85 dB for almost any work environment, plus a brilliant red warning light.

SpecificationsDisplay -High contrast numerical level display and high intensity LED alarm warning indication and alert buzzerSensor Life -Up to 60 months, dependent upon sensor typeRF Frequency Protection -Readings will not change by more than 5% of full scale when placed no less than 2’ from a 5-Watt radio transmit-ting on a frequency of 30, 150, or 450 MHzBattery -18-24 months, non-alarming, lithium camera battery, in-cludedSpecial Features - Power “On/Off” switch plus convenient dual zero and span adjustment for calibration at alarm point for toxic gases or 20.9% for oxygen, optional vibratorIntrinsic Safety - Class 1, Div 1, Groups A, B, C, D, CSA approvedSize -3.65” L x 1.7” W x 1.1” H, Weighs -5.5 ouncesEach monitor includes calibration adapter, tubing, manual and case.

Item Description Price450-450-100 450SeriesOxygenDetector $365.00450-450-101 450SeriesCarbonMonoxideDetector $452.00450-450-103 450SeriesChlorineDetector $635.00450-450-104-A 450SeriesAmmoniaDetector $650.00450-450-106 450SeriesHydrogenCyanideDetector $635.00450-455-100 455OxygenDetectorw/Vibrator $422.00450-455-101 455CarbonMonoxideDetectorw/Vibrator $509.00450-455-103 455ChlorineDetectorw/Vibrator $685.00450-455-104A 455AmmoniaDetectorw/Vibrator $699.00450-455-106 455HydrogenCyanideDetectorw/Vibrator$685.00

•

•

•

•

•

••

•

•

•••

ToxiRAE IIThe ToxiRAE II is a single-gas, personal protection monitor that continuously displays toxic gas concentrations. It costs just a little more than disposable detectors, unlike typical disposables that only display “remaining life”, the ToxiRAE II is a full-featured gas monitor providing continuous, digital display of the gas concentration, STEL, TWA, and Peak values as well as high, low, TWA, and STEL alarms.

A simple to use one-button product, the ToxiRAE II is easy to calibrate. Use the pre-set alarms, or modify the alarms to meet your specific requirements. In contrast to disposables that are turned on once and remain on until their batteries expire, you decide when and where to use your ToxiRAE II and you turn it on and off accordingly.

Large, easy-to-read continuous display of gas concentration in ppmDisplays STEL, TWA, and Peak valuesSensors available: H

2S, CO, O

2, NH

3, Cl

2, ClO

2, HCN, NO, NO

2,

PH3, SO

2Field replaceable battery and sensor2-Year warrantyUser adjustable high, low, STEL, and TWA alarmsVarying audio alarm signals for different alarm conditions

Ideal for use in: Refineries, Oil and Gas, Contractors, Chemical, Pulp and Paper plants, Fire Service and Industrial.

Item Description Price045-0512-000 CarbonMonoxide0-500ppm $249.00045-0518-000 Ammonia0-50ppm $349.00045-0516-000 Chlorine0-10pp $349.00045-0517-000 HydrogenCyanide0-100ppm $349.00045-0511-000 HydrogenSulfide0-100ppm $249.005-0512-200 CarbonMonoxide0-1999ppm $299.00045-0006-000 Oxygen0-30% $249.00045-0515-000 NitrogenDioxide0-20ppm $349.00

Please call for volume pricing and additional information.

•••

••••

Pac 5000 Single-Gas DetectorDrager Pac 5000 is the innovative single-gas instrument for personal gas detection. It provides reliable monitoring of ambient air and gives a fast warning of harmful concentrations of carbon monoxide, hydrogen sulfide, and oxygen. Using the concentration display and event logger, the Drager Pac 5000 can be used maintenance-free for over two years without replacing the sensor.

Item Description Price4543846 CO0to500ppm35ppm50ppm $245.004543847 H2S0to100ppm10ppm20ppm $245.004543848 O20to25Vol.-%19.5Vol.-%23.5Vol.-% $245.00


SING

LE-G

AS –

IN

STR

UM

EN

TS ToxiPro Gas Detector

ToxiPro is a fully serviceable, reusable gas detector with real-time Peak, STEL, and TWA Readings, as well as a black box data recorder. A full-featured datalogger is available as an upgrade for the Toxi Pro.The ToxiPro features one-button calibration. To make routine mainte-nance even easier, the ToxiPro can be used with the IQ Express Docking Station – an automatic bump test and calibration station with built-in recordkeeping.

DesignIP65/IP67 rated protection against water and dust Compact and ruggedOver-molded bootOne button operationLarge backlit displayLoud alarmTop & front mounted LED alarm light.Translucent case option for enhanced alarm visibilityOptional built-in vibrating alarm.Exceeds IEC 6100-4-3 for level 3 RFI immu-nity specifications.

Data storage and downloadingStandard event logger stores latest 20 events, in-cluding sensor type, max reading, average reading, time and durationIrDA PC communicationStandard black-box data recorderDatalogger upgrade optional

Batteriy lifeReplaceable Lithium battery - 9000 hours of operation

Sensors and calibrationO

2, CO, H

2S, SO

2, CO+, CO-H, Cl

2, ClO

2, NH

3, NO

2, PH

3, HCN

One-button automatic calibration

AlarmsLow, high, STEL and TWA audible and visible alarmsOptional vibrating alarm

Standard accessories:Heavy-duty alligator clipCalibration adapterReference manual and quick reference card

Value kit - All standard accessories, plus:Compact-sized (34 liter) cylinder of calibration gas., fixed-flow regulator and foam-lined carrying case.

Item Description Price54-45-90 Oxygen–Standardkit $229.0054-45-01 CarbonmonoxideStandardkit $239.0054-45-01K CarbonmonoxideValuekit $389.0054-45-05 COPlusStandardkit $239.0054-45-05K COPlusValuekit $389.0054-45-19 COMinusH,reducedsensitivitytoH2 $299.0054-45-19K COMinusH,reducedsensitivitytoH2 $449.0054-45-02 HydrogensulfideStandardkit $239.0054-45-02K HydrogensulfideValuekit $484.0054-45-03 SulfurdioxideStandardkit $350.0054-45-03K SulfurdioxideValuekit $585.0054-45-21 AmmoniaNH3Standardkit $399.0054-45-21K AmmoniaNH3Valuekit $984.0054-45-18 ChlorineStandardkit $375.0054-45-18K ChlorineValuekit $750.0054-45-09 NitrogendioxideStandardkit $375.0054-45-09K NitrogendioxideValuekit $750.0054-45-10 HydrogencyanideStandardkit $375.0054-45-13 PhosphineStandardkit $375.0054-45-13K PhosphineValuekit $750.00

••••••••

••

•

•••

•

••

••

•••

Single Gas Monitors (01 Series)2 preset adjustable alarm levelsOperates 16 hours on 2 AAA alkaline batteriesLow battery alarmAlligator or belt clip availableChoose from: LEL, O

2, H

2S, CO

Vibration, visual and audible alarms

Item Description Price72-0008RK-01 OX-01,0-40%O2withalkalineand alligatorclip $350.0072-0033RK-01 GP-01,0-100%LELwithalkalineand alligatorclip $420.0073-0044RK-01 CO-01,0-500ppmwithalkalineand alligatorclip $350.0073-0046RK-01 HS-01,0-100ppmwithalkalineand alligatorclip $350.00

••••••

110 Series XLAll the simplicity, reliability and ease-of-use of our standard Shield but the Shield XL takes a step up with extra precision and lifespan.The Shield XL gives you more options to detect more gases with the power of “continuous gas reading.” You can measure at a lower parts-per-million resolution for situations that call for finer gas readings. The XL also delivers security in the choice of two methods of gas monitoring: Short Term Exposure Limit (STEL) and Time Weighted Average (TWA) exposure. Switch from one to the other to adapt to different work situations.The Shield XL features a replaceable battery and sensor to help reduce total cost of ownership. Ten year warranty on electronics and 2 year war-ranty on the battery, CO and H2S sensor.

Item Description Price110-495-101XL 110SeriesXLCarbonMonoxide $255.00110-495-102XL 110SeriesXLHydrogenSulfide $255.00

110 Series XLSTake all the advances packed into the Shield XL and add another big one: four different program-mable alarm settings. The Shield XLS gives you the flexibility to adjust the alarm to suit your spe-cific needs in a variety of working environments. Its combination of the STEL alarm, TWA alarm and adjustable alarm settings you can change in the field means the XLS helps you master your environment in way other detectors just can’t.

Item Description Price110-495-102XLS110SeriesXLSHydrogenSulfide $285.00


INSTR

UM

EN

TS – SINGLE-GAS

Toxi Vision EX Single- Sensor Combustible Gas DetectorThis fully serviceable gas detector features real-time gas reading, max readings for the current operating session, and customizable warning and danger alarms to let you know when combustible gas is presentThe Toxi Vision EX is available in your choice of Alkaline or NiMH recharge-able versions. The NiMH rechargeable version includes a black box data recorder and an event logger as standard equipment. The black box in the NiMH version can be upgraded to a full-featured datalogger at any time after purchase. At this time, the alkaline version is not available with any type of data recording system.

Design:One-button operationLarge backlit displayLoud alarm (92dBA @ 1 foot)Alkaline version is rated IPX5/IPX7 against water ingress and NiMH version is rated IPX5RFI immunity to 40 V/mTop- and front-mounted bright LEDSecurity beep (selectable via PC)

Batteries:Alkaline model runs up to 13 hours on 2 AA batteriesNiMH model runs up to 15 hours between chargesNiMH rechargeable version includes charger

Calibration:One-button automatic calibration

Readout and alarms:Programmable warning and danger alarms (via PC)Current and max gas readings

Data:NiMH version comes with standard black box data recorder and event loggerAlkaline version has no data recording options

Standard Accessory Kit includes:Belt clip, calibration adapter. reference manual, and quick reference card. Rechargeable NiMH version includes charger.

Confined Space Complete Kit Includes:All standard accessories, plusStandard sized (103 liter) cylinder of calibration gasFixed flow regulatorFoam-lined waterproof hardshell carrying case

Value Kit IncludesAll standard accessories, plus

Compact sized (34 liter) cylinder of calibration gasFixed flow regulatorFoam-lined hardshell carrying case

Add suffix (K) for Value kit or (C) for Confined space kit

Item Standard Value Kit Confined KitToxiVisonEx w/ Alkaline batteries

54-37-80A $345.00 $495.00 $675.00

ToxiVisionEX w/Recharge. NiMH54-37-80N $395.00 $545.00 $725.00

Options and replacement sensors available, please call for more information.

••••

•••

•••

•

••

•

•

•

•

••••

•••

Titan® Combustible Gas DetectorThis single-gas instrument, used for detection of flammable gases or vapors, is reliable, easy to use and durable.

One-button operationStrong, reliable constructionLarge, easy-to-read displayMaximum alarmsPower supply flexibilityDurable sensor

Prices starting at $550.00

••••••

Toxi Vision Single Sensor Gas Detector The Toxi Vision is a durable, 3.5” x 2.5“ single-sensor gas detector that offers consistent long-term protection and low cost of ownership. Features a rugged metal-plated case that is immune to both RFI and the elements. One-button operation keeps it simple. A few minutes of training is all it takes to ensure proper operation. The large liquid crystal display can be easily seen from several feet away. A manually-activated backlight ensures the visibility of the readings even in low light conditions. An audible alarm and bright LED alarm light warn users of dangerous conditions, while an optional vibrating alarm is available for use in high-noise environments.

Item Description Price54-37-90 Oxygen(O2) $345.0054-37-01 CarbonMonoxide(CO) $345.0054-37-02 H2SHydrogenSulfide $395.0054-37-21 NH3Ammonia $445.0054-37-18 Cl2Chlorine $445.0054-37-20 ClO2ChlorineDioxide $445.0054-37-13 PH3Phosphine $445.0054-37-0N VibratingAlarm $50.00

LKD100 Combustible Gas Leak Detector

Low-cost leak detection of natural gasPulsed-tone audible alarm and LED visual alarm

The LKD100 is an ideal, low-cost monitoring solution for fire and police workers that may encounter or check for natural gas leaks during the course of their day. The LKD100 offers continu-ous detection of natural gas leaks and sounds an alarm when the combus-tible gas concentration exceeds the preset level of 500 ppm.

The unit fits comfortably in a shirt pocket or tool belt and the recharge-able version (charger included) provides up to 10 hours of continuous monitoring. The alkaline version uses two AA batteries for up to 8 hours of run time. UL approved for use in Class I, Div. 2 hazardous locations.

Item Description Price18104620 LKD100Combustible GasLeakDetector(Alkaline) $145.0018105270 LKD100Combustible GasLeakDetector(Rechargeable) $195.00

••


SING

LE G

AS •

SING

LE-G

AS D

ISPO

SABL

ES –

IN

STR

UM

EN

TS

ALTAIR Single-Gas Detector More than two years of high performance!The ALTAIR Single-Gas Detector featuring sensor options for carbon monoxide, hydrogen sulfide and oxygen will operate for over two years. This long lifespan, coupled with the unit’s high performance, results in one of the most cost-effective monitors on the market. Advanced design offers superior dust and water protection and high resistance to RFI. A rubberized housing and one-button operation provide the durability and ease of use users expect from MSA instruments. The triple-alarm system featuring two bright LEDs, a piercing audible alarm, and a vibrating alarm ensures that no alarm condition goes unnoticed.

The ALTAIR Detector automatically records the last 25 alarm and test events. To read data or change alarm set points simply connect the unit to an MSA infrared adapter using the built-in IR communication port.

Approvals & StandardsUS & Canada: Class 1, Div 1, Groups A, B, C & DEurope: ATEX II 2G Eex ia IIC T4 -20ºC to +50ºCAustralia: Ex ia IIC T4 -20ºC to +50ºC

ApplicationsChemicalConstructionElectric UtilityGas DetectionGeneral IndustryHazardous MaterialsIndoor Air QualityManufacturingNuclearOil and GasWater/Wastewater

HazardsLeak DetectionOxygen DeficiencyToxic Atmosphere IDLHToxic Atmosphere Non-IDLH

Please call for pricing and additional information.

Prices starting at $199.00

•••

•••••••••••

••••

Pac IIIGood Value Single Gas MonitorThe Pac III Monitor delivers the most value of any single gas monitor avail-able. The most sensors available, plus the loudest audible alarm, the largest display the easiest to use electronics, and the smartest sensors. All of these features are found in this small and rugged gas monitor. Using Dräger-Sensor® technology, the Pac III is the most versatile gas detection instru-ment because it can utilize any one of Draeger’s 30+ intelligent sensors, and quickly switch between them in the field.The Dräger-Sensors® provide fast and accurate response to hazardous gas levels while the attention-getting alarms make sure you know the danger is present. The Pac III provides the most sensing and alarming capabilities of any single gas monitor in the industry today.

Rugged HousingMany gas-monitoring applications are also environmentally challenging. It is not uncommon to work in environments that are hot, cold, wet, dirty, or affected by corrosive gases. These extreme working environments, such as an offshore oil rig or an underground mine, put equipment to the test. The Pac III was designed to handle these tough conditions in stride, and it does! The metal plated ABS housing provides a lightweight package that is easy to wear, but can take a beating in the field.Regardless of accidental drops, unintentional bumps, or the occasional submersion in water, the Pac III is still ready to measure gas and sound its alarms. O-rings seal the housing from water or dust. The horn and sensor compartments are sealed against the elements too. The Pac III is ready for the most demanding applications.

Ideal for the protection of workers and contractors at chemical plants, oil platforms, steel mills, mines and almost any other industrial working environment.

UL, Classes I & II, Division 1 Group A-D, T6

Sensors Accepted: H2S, CO, O2, CL2, NO2, NH3, HCN, NO, CO2, HF/HCL, H2, H2O2, N2H4, H2SHC, CO-HC, PH3-HC, Organic Vapors, Hydrides, Amines and Odor.

Item Description Price4530010 PacIIIStandard $465.004530011 PacIIIHygiene(withdatalogger) $565.004530311 PacIIIHygieneKit(withdownloadkit) $1,025.00

Plus we offer all the accessories, like leather carry case and Computer hardware and software kits. Sensors ordered separately, please call for available sensors.

sells, rents and services, most brand name Gas Detection Devices. Please contact our Customer Service or Repair Departments for more information.


INSTR

UM

EN

TS – SINGLE-GAS DISPOSABLES

Pac 1000Ideal for short-term projects such as shut down activities This maintenance-free instrument guarantees the reliable monitoring of ambient air and pro-vides a fast warning against harmful concentra-tions of carbon monoxide, hydrogen sulphide, or oxygen.By using the status display and without replac-ing the battery or the sensor, the Dräger Pac 1000 can be used maintenance-free for over 100 days. This small, ergo-nomic instrument is equipped with an alligator clip in order to securely fasten the unit to the user.For individual configuration, calibration and adjustment of the bump test mode, the instrument can be connected using the connecting cradle to a PC with the installed software PAC Vision or CC-Vision. Several instru-ments can be configured and calibrated at the same time.

Item Description Alarm Threshold Price4543858 Pac1000forCO 30pppm-60ppm $115.004543859 Pac1000forH2S 10pppm-20ppm $115.004543860 Pac1000for02 19Vol-% $115.004543822 LeatherCarrycase $31.00

Pac 3000 Single-Gas DetectorPersonal monitoring single-gas instrumentEnsures reliable monitoring of ambient air and fast warnings against harmful concentrations of carbon monoxide, hydrogen sulphide, and oxygen. Thanks to its low-power status display, the Drager Pac 3000 can be used maintenance-free for over two years without replacing the sensor. This small and ergonomic instrument is covered with a rubber housing and meets the requirements of IP 65. An alligator clip provides secure attachment of the unit to the wearer. Ease of use is enhanced by the following features:

Two-button operationEasy to change lithium batteryLarge, strongly backlit language-free display

Item Description Price4543840 CO0to500ppm35ppm50ppm $195.004543841 H2S0to100ppm10ppm20ppm $195.004543842 O20to25Vol.-%19.5Vol.-%23.5Vol.-% $195.00

•••

Mighty-Tox The Mighty-Tox is an inexpensive, rugged, single-sensor, disposable gas detector that is available for the detection of either hydrogen sulfide (H2S) or carbon monoxide (CO). Once the Mighty-Tox is activated, it monitors continuously for a full 90-days. A built-in test button lets you verify the unit is operating properly. As the instrument reaches the end of its operational life, a low-battery alarm begins to sound and then continues to sound once per minute for the last seven days of operation. After the Mighty-Tox has reached its end of service life simply throw it away.

Item Description Price54-28-02 HydrogenSulfide(H2S) $100.0054-28-01 CarbonMonoxide(CO) $100.00

GasBadge® Plus Personal Single-Gas Monitor

2-year continuous monitoringLow-cost O

2, CO, H

2S, SO

2 or NO

2

monitoringPPM or % by volume readoutPowerful audible alarm complemented by vibrat-ing and visual alarms, standardUser adjustable alarm and calibration gas setpointsWater resistant2-year warranty

GasBadge® Plus is a two-year, maintenance-free, single gas monitor ideal for personal protection from unsafe levels of oxygen, carbon monoxide, hydrogen sulfide, sulfur dioxide or nitrogen dioxide. The unit’s compact size and light weight - 2.5 oz – (72 grams) allow it to be worn comfortably with a variety of clip attachments, and the top-mounted sensor provides continuous and unobstructed protection even when placed in a shirt pocket. The rugged enclosure is extremely durable, and resistant to water and radio frequency interference. A protective concussion-proof overmold protects the unit from extreme abuse in a variety of harsh industrial environments.

Item Description Price18100050-1 GasBadge®Plus–CarbonMonoxide(CO) $195.0018100050-2 GasBadge®Plus–HydrogenSulfide(H2S) $195.0018100050-3 GasBadge®Plus–Oxygen(O2) $195.0018100050-4 GasBadge®Plus–NitrogenDioxide(NO2) $325.0018100050-5 GasBadge®Plus–SulfurDioxide(SO2) $325.0018106401 GasBadge®PlusNylonCarryingCase $10.0018106419 GasBadge®Plus2-unitNylonCarryingCase $15.0018106500 GasBadge®Constant-FlowHandPump $149.0017121963 GasBadge®NeckLanyardw/SafetyRelease $5.0017124504 Replacementwater/dustsensorbarriers(5ct.)$10.0018106260 GasBadge®Datalink $150.0018106344-00 CalPlus™CalibrationStation $795.0018106344-10 CalPlus™CalibrationStation w/on-boardprinter $1,095.0017117714 Serialdatathermalprinter withinfraredinterface $395.0017117722 Serialdatadotmatrixprinter, 120VACpowered $395.00

••

••

•

••

110 Series Single-Gas MonitorsMaintenance-free, two-year guaranteeEquipped to display actual readings, peak exposure level, life remaining, and two alarm setpoints. Designed to be compact and light-weight, it can be easily slipped into a pocket, or clipped to belt or hard hat.

Rugged, compact sizeTwo-year, maintenance-free protectionInternal vibrator alarmTwo alarm levels (other alarm points avail-able from the factory)Peak reading Simple one button operation

Item Description Price110-495-100 OxygenShield $211.68110-495-101 COShield $230.79110-495-102 H2SShield $232.00

••••

••


SING

LE-G

AS D

ISPO

SABL

ES •

PID

SING

LE-G

AS –

IN

STR

UM

EN

TS

VX500 Photo Ionization Detector Ideal for arson investigation and HazMat Internal pump for remote sample90 dB audible & LED alarm

The VX500 PID uses a field-re-placeable, plug-in detector and 10.6eV lamp to detect and measure hazardous volatile organic compounds (VOCs) like toluene, xylene and vinyl chloride at levels as low as 100 parts per billion (ppb). The VX500 has 100 response factors factory-load-ed that enable the display reading to be tuned to a particular gas while still providing easy access to the most commonly encountered hazards.

Features include one-button calibration with user-definable security code, TWA and STEL readings with peak/hold memory, and a time-delay pow-er button that prevents unintentional shut-off. The large LCD display offers manual or automatic backlighting in darkness or alarm conditions. The VX500 is compatible with ISC’s Docking Station, allowing complete use of that system’s automatic calibration and record-keeping functions. Choose rechargeable lithium-ion batteries for up to 18 hours of run time, or three replaceable AA alkaline batteries for up to 7 hours of run time. The VX500 is housed in an impact-resistant ABS composite case that provides full EMI and RFI shielding.

Item Description Price18104034-0001 VX500PIDMonitor w/10.6eVLamp(Li-ion) $2995.0018104034-0001A VX500PIDMonitor w/10.6eVLamp(Alkaline) $2900.00

•••

MiniRAE 2000The smallest pumped handheld volatile organic com-pound (VOC) monitor on the market. Its Photoioniza-tion Detector’s (PID) extended range of 0-10,000 ppm makes it an ideal instrument for applications from envi-ronmental site surveying to HazMat/Homeland Security.

Measure more chemicals than with any other PIDWhen a gas is selected from MiniRAE 2000’s library its alarm points are automatically loaded into the meter.

Monitor Only includes:MiniRAE 2000 unit with 10.6 eV PID detectorNickel metal hydride batteries w/ chargerAlkaline battery holderProtective Rubber bootInlet probe and water trapOperation and maintenance manualSoft carry caseTool Kit

Item Description Price 011-0201-000 MniRae $3,545.00011-0201-100 MiniRaew/datalogging $4,045.00

••

••••••••

Toxi3Ltd and ToxiLtd Disposable Single-Gas MonitorsThe Toxi3Ltd and ToxiLtd are both low-cost, full-featured, disposable single-gas monitors with an operating life of two full years. The ToxiLtd is available for the detection of your choice of O2, CO, H2S or SO2. Despite its low price and ease of use, the Toxi3Ltd and ToxiLtd are sophisticated gas detectors rated to IPX5/IPX7 against water ingress and even includes an event logger as standard equipment. Choose from a two - or three-year battery life.

DesignCompact and ruggedIPX5/IPX7 rated protection against waterOver-molded bootOne button operationLarge displayLoud alarmTop & front mounted bright LEDAvailable with built-in vibrating alarmExceeds IEC 6100-4-3 for level 3 RFI immunity specifications

Data storageAutomatic event logger (Latest 20 events, including sensor type, max readings, average readings, time and duration)

ReadoutDisplays service life remaining unless alarm condition is presentDuring alarm condition, actual gas reading is shown

Battery LifeToxiLtd: Internal Lithium - 2 years of operationToxi3Ltd: Internal Lithium - 3 years of operations

Sensors and calibrationO

2, CO, H

2S, or SO

2One-button automatic calibration

Standard accessories:Heavy-duty alligator clipCalibration adapter.Reference manual and quick reference card

Value kit - All standard accessories, plus:Compact-sized (34 liter) cylinder of calibration gasFixed-flow regulatorFoam-lined carrying case

Toxi3Ltd ConfigurationItem Description Price54-52-01 CarbonMonoxideStandardKit $229.0054-52-01K CarbonMonoxideValueKit $379.0054-52-02 HydrogenSulfideStandardKit $229.0054-52-02K HydrogenSulfideValueKit $474.00

ToxiLtd ConfigurationItem Description Price54-44-90 OxygenStandardKit $189.0054-44-01 CarbonMonoxideStandardKit $199.0054-44-01K CarbonMonoxideValueKit $349.0054-44-02 HydrogenSulfideStandardKit $199.0054-44-02K HydrogenSulfideValueKit $444.0054-44-03 SulfurDioxideStandardKit $299.00

•••••••••

•

••

••

••

•••

•••

Toxi3Ltd

ToxiLtd


INSTR

UM

EN

TS – PID SINGLE-GAS

ppbRAE PlusVolatile organic compound (VOC) monitorThe rugged ppbRAE Plus is the most sensitive handheld volatile organic compound (VOC) monitor in the world. Its Photoionization Detector (PID) provides true parts-per-billion (ppb) detection for applications from indoor air quality (IAQ) to HazMat/Homeland Security.

The ppbRAE Plus detector can be made wireless with the use of RAELink2. This allows real-time monitoring information from the detec-tor to be integrated into an existing AreaRAE system. A wireless RF (radio frequency) modem allows detectors equipped with Firmware version 1.20 or higher to communicate and transmit readings and other information on a real-time basis with an AreaRAE base controller located up to 2 miles away.

Key Features:New extended range from 1 ppb to 2,000 ppmProven PID technology: The patented dual-channel 3D sensor provides a 3-second response time and sets a new standard for resistance to moisture and dirt, while the superbright 10.6eV lamp provides extra sensitivity for low ppb measurements.Exclusive zeroing tube assures repeatability at low-level measurements with a disposable VOC zeroing tubePatented self-cleaning lamp and sensor minimize the need for mainte-nance and calibrationThe ppbRAE Plus lamp and sensor can be taken apart in seconds for easy maintenance without any toolsMeasure more chemicals than with any other PID: with over 100 Cor-rection Factors built into the ppbRAE Plus’s memory and the largest printed list of Correction Factors in the world (300+), RAE Systems offers the ability to accurately measure more ionizable chemicals than any other PID. When a gas is selected from the ppbRAE Plus’s library, its alarms points are automatically loaded into the meterDrop-in battery: when work schedules require putting in more hours than the 10 hours supplied by the standard NiMH battery, the drop-in alkaline pack supplied with every ppbRAE Plus lets you finish the jobStores up to 267 hours of data at one-minute intervals for downloading to PC (with the datalogging option)

Applications:HazMat/Homeland Security, Indoor Air Quality, Industrial Hygiene and Safety, Environmental

Item Description Price025-0201-000 ppbRAEPlusPGM-7240with Universalcharger $6,245.00025-0201-100 ppbRAEPLUSPGM-7240with AccessoryandCalibrationKit $6,745.00

••

•

•

•

•

•

•

UltraRAE Monitor The UltraRAE is a quick, spot-check monitor typically used by occupa-tional health, safety, and environmental personnel. The combination filter tube and Photoionization Detector (PID) removes the disadvantages as-sociated with colorimetric tubes and gas chromatographs. The UltraRAE has the advantage of providing a fast, continuous reading and datalog-ging of concentrations of Benzene, Methylene Chloride, or Butadiene. Applications include tank entry pre-screening during refinery and plant maintenance, hazardous material response, marine spill response, and refinery down-stream monitoring. Monitor only includes:

UltraRAE monitor, Model PGM-7200Rubber boot with belt clipRechargeable NiMH battery w/chargerAlkaline battery adapterTotal VOC tube10 - RAESEP bar-coded benzene pre-tubesProRAE Suite Software for datalogging, computer cableManual and soft leather case

Monitor kit includes:UltraRAE monitor, Model PGM7200Rubber boot with belt clipRechargeable NiMH battery w/chargerAlkaline battery adapter

Calibration kit includes:5-ppm benzene calibration gas (34L cylinder), Tedlar bag, 3-liter/minute regulatorHard transport case with precut foamLamp cleaning kit and toolsTotal VOC tube10 RAE-SEP bar-coded benzene pre-tubesProRAE Suite Software for datalogging, computer cableManual and soft leather case

Item Description Price012-7003-000 UltraRaeMonitor $4,600.00012-0002-000 Monitorw/AccessoriesKit $4,850.00012-0000-000 Monitorw/Accessories&CalibrationKit $5,100.00

••••••••

••••

•

••••••

ToxiRAE Personal PIDFits in a pocket for monitoring of worker exposure to Volatile Organic Compounds (VOCs).

Rechargeable Ni-Cd battery provides up to 10 hours of continuous operation Keys easily accessible even with gloves Large easy-to-read back-light display Easily changeable PID lamp and sensor Varying audio alarm signals for different alarm conditions Factory preset and user programmable alarms Protects from interference by portable radios (RFI)

Includes: Calibration adapter with tubing, protective rubber boot with integral belt clip, operation and maintenance manual, alkaline adapter for 2 AAA batteries and Ni-Cd battery and charger.

Item Description Price007-0001-001 ToxiRAEMonitor $1,450.00007-0002-001 ToxiRAEMonitorw/datalogging $1,700.00

•

•

•

••••


SPEC

IALT

Y DE

TECT

ION

–

INSTR

UM

EN

TS HAZMATCAD Plus Chemical Agent Detector

Detects both chemical warfare agents and selected toxic industrial chemi-cals (TICs). Both units are ruggedly constructed, compact and light-weight. They are also extremely easy to use, requiring no prior training. A single key press begins automatic sampling and analysis. Audible and visual alarm messages provide clear and simple alarm condition display. Offers self-diagnostic check during rapid warm-up, alphanumeric display with LED alarms and 8-12 hour operation with rechargeable lithium ion batteries. Vapor diffusion check source verifies system perfor-mance. The inlet design protects against dust and particulates. Kits include a battery charger, belt clip, two Sony long-life lithium ion rechargeable batteries, a waterproof carrying case, vapor check source and operating manual.Used to detect these hazards:

Combustible atmosphereConfined spaceOxygen deficiencyToxic atmosphere IDLHToxic atmosphere Non-IDLH

Call for Pricing and Availability

•••••

ChemRAEPortable, Wireless, Chemical Warfare Agent Detection SystemsSmall enough to use as a personal detector, a monitor for surveying contaminated areas or a fixed installation detector. ChemRAE is the latest in state-of-the art hand-held Chemical Warfare Agent detection and identification systems. The ChemRAE uses proven Open Loop Ion Mobility Spectrometry (IMS) technology for enhanced selectivity and sensitivity. It is designed to detect Chemical Warfare Agents and toxic industrial chemicals.

Can be used as a stand-alone portable monitor or integrated into an AreaRAE network by using a RAELink2 modem. Integration into an Area RAE network allows you to add CWA to existing complement of RAE Systems portable gas monitors. Weighs less than 2 lbs, can be powered by a rechargeable lithium-ion battery pack or AA batteries. Clear and simple user interface can be operated with one hand. ChemRAE stores agent alarm information for retrieval at a later time to provide historical log of events. ChemRAE has no consumables and does not require expendable desiccant cartridges. Designed for low life cycle and operating costs.

Ideal for First Responders, HazMat Management, and Fixed and Vehicle-Mounted CWA monitoring.

Please call for information on ordering and accessories.

Complete kits starting at $9,000.00

Draeger CMS AnalyzerAccurate gas measurements are made easier with the Draeger CMS. This new generation spot-check detection device is literally as easy as 1-2-3 to operate. Simply insert one of the 55 chemical-specific CMS Chips into the Analyzer and follow the instructions on the display as to when to move the slide switch. TWA levels are typically analyzed in 1-2 minutes. Upon completion of this process, the concentration is indicated on the LCD display.

Easy to useDigital display of resultsOn-board data-recorder UL, CSA, and MSHA approvedNo gas calibration required Accuracies up to +/- 4%

Item Description Price6405300 CMSAnalyzerSetwithDataRecorder: IncludesAnalyzer,4AAAlkalineBatteriesand 3mmAllenWrench $1,729.008317700 CMSAnalyzerwithRemoteSystem $2,295.004055711 CMSEmergencyResponseKitIncludesAnalyzerSet, RemoteSystem,BarProbe,10ChipsandCarryingCase (includesthefollowingchips:Ammonia10.0-150ppm, CarbonDioxide1,000-25,000ppm, CarbonMonoxide5.0-150ppm $3,585.004055976 CMSEmergencyResponseKitwithoutChipsIncludes AnalyzerSet,RemoteSystem,BarProbeand CarryingCase $2,940.004056455 CMSIndoorAirQualityKit:IncludesAnalyzerSet, 4ChipsandNylonTransportCase(includesthe followingchips:CarbonDioxide200-3000ppm, CarbonMonoxide5.0-150ppm, Formaldehyde0.20-5.0ppmandOzone25.0-1000ppb) $1,976.00

••••••

HazMat Kits for identify-ing unknown chemicalsDeluxe HazMat Kit contains the follow-ing: Gastec Model GV-100 Pump Kit (GV-100-S-TR), Gastec Detector Tube Handbook, hard shell carrying case, 5 meter extension hose with rubber shroud tube holder, 2 light sticks, Decision Chart I, Irritant Smoke Tube Kit (9500), M8 De-tection Paper (1-0 Tests), tweezers, Ammonia tubes (3L), Benzene tubes (121S),l Carbon monoxide tubes (1LA), Chlorine tubes (8LA), Ethyl acetate tubes (141L), Hydrogen cyanide tubes (12L), Hydrogen sulfide tubes (4LL), Hydrocarbons (low class) tubes (103), Hydrocarbons (high class) tubes (105), Petroleum naphtha tubes (106), Polytec I tubes (Quali-tative Test) (107), Stoddard Solvent tubes (128), Sulfur dioxide tubes (5LB). Note: Each kit contains 1 box of each type of Gastec tube listed in description. Most boxes contain 10 tubes unless otherwise noted.

Item Description PriceST101 DeluxeHazMatkit $1,375.00


INSTR

UM

EN

TS – RADIATION DETECTION

GammaRAE IIThe GammaRAE II is a rapid de-tector of y-ray (gamma) sources. It is the only personal radiation detector with a loud audible alarm; big, bright flashing LEDs; and a vibration alarm. The Gam-maRAE II contains a sensitive Cesium Iodide (CsI) scintillator for excellent search capability and fast response, and works well in applications from law enforce-ment to HazMat teams and fire departments.

Prominent visible, audible and vibration alarms

•

NeutronRAE IINeutronRAE II is the first personal radiation de-tector to provide rapid detection of both gamma (Y) ray and neutron sources even in potentially flammable environments. Certified intrinsically safe and water-immersible for chemical decon-tamination purposes, the NeutronRAE II can be safely used in more environments than any other personal gamma and neutron radiation detector.

The NeutronRAE II is designed for use in rough environments. It is immersible (IP67) in water for easy decontamination, and it”s concussion-proof case provides shock protection if the detec-tor is dropped. The two-button operation is designed for use even in Level A protection suits with two layers of gloves.

The NeutronRAE II features fast response time for both the neutron and gamma radiation. Alarm modes can be set to operate in “Search Mode” based on local background radiation levels or “Safety Mode” providing high and low alarm levels based on absolute dose rates.

Detects neutrons from weapons-grade Plutonium (239Pu)Sensitive CsI and LiI scintillators for excellent search capability and fast responseProminent visible, audible and vibration alarmsImmersible in water for easy decontaminationTop-mounted reversible displayContinuous digital readout in µR/h (µR/em/h), µSv/h (µSieverts/h), and cps (counts per second) for gamma; cps (counts per second) for neutron radiationDust and shock resistantTwo AA Alkaline batteries last up to 600 hoursAutomatic background level referencing on start-up and upon user demand Passes drop test from 59” (1.5m) to hard concreteLow EMI interference from cell phones and portable radiosProgrammable search and high/low safety alarms

Used by: First responders to radioactive threats, Fire Departments, HazMat teams, Military and government.

Kit Includes:NeurtonRAEIIBelt clip and wrist strap2 AA alkaline batteriesOperation and maintenance manualProRAE Studio Radiation software

Item Description Price047-0401-000 NeutronRAEIIPagerKit $1,995.00

••

••••

•••

•••

•••••

GammaRAE II ResponderThe GammaRAE II Responder is two instru-ments in one: it has the rapid response of a detector and the accurate dose measurement of a dosimeter. It is designed specifically to meet the needs of first responders. This instrument contains two separate sensors. The Cesium Iodide (CsI) scintillator provides a fast, two-second response to radiological threats, while the energy-compensated PIN diode provides high dose rate range coverage and accurate dose mea-surements. The GammaRAE II Responder accumulates accurate total dose. Stored dosage data can be cumulative or reset for each use period. It alerts the wearer with a loud audible alarm; big, bright flashing LEDs; and a built-in vibration alarm. For stealth operations, law enforcement personnel can disable each alarm individually.

Immersible (IP67) design makes for reliable operation in wet environ-ments and easy decontamination. IS certification permits operation in potentially flammable/explosive environments.Sensitive CsI scintillator for excellent search capability and fast response Energy-compensated PIN diode sensor for high dose rate range and accurate dosimeter capabilities Prominent visible, audible and vibration alarms Immersible in water for easy decontamination Top-mounted reversible display Continuous digital readout in µR/h (µR/em/h) or in µSv/h (µSieverts/h) and cps (counts per second) Two operation keys, simple intuitive programming Two AA Alkaline batteries last up to 500 hours Large, 30,000-point datalog capacity, downloaded via cable-free Blue-tooth® connection

Applications Alerts First Responders to radioactive threats Accurately measures accumulated dose to the wearer Customs and border patrols Ideal for: Law enforcement; Security officers in nuclear power facilities, banks, government laboratories and medical facilities; Military; Govern-ment agencies; HazMat teams; Fire Departments

Item Description Price047-0501-000 GammaRAEIIResponder $1,195.00

•

••

••••

•••

••••

Water-resistant for easy decontaminationTop-mounted reversible displayContinuous digital readout in µR/h (µRem/h) and cps (counts per second). Optional readout in µSv/h (µSieverts/h)Fast < 0.5-second responseTwo operation keys, simple programmingCalibrated for lifeTwo AA Alkaline batteries last up to 800 hoursAutomatic background level referencing on start-up and upon user demandLow EMI interference from cell phones and portable radio

Item Description Price0470303-000 GammaRAEII Kitincludes,beltclip&batteries $995.00

•••

•••••

•


FIXE

D SY

STEM

S –

IN

STR

UM

EN

TS iTrans™ Fixed-Point

Gas Monitor The iTrans Fixed-Point Gas Monitor offers maximum flexibility, superior performance and lower installation costs by providing one or two points of detection from a single head. The iTrans employs “smart” sensor technology to monitor a specific environment for a combination of any two gases. “Smart” sensors feature automatic sensor recogni-tion, zero and cal fault protection and access code security. Each unit is a microprocessor-controlled transmitter that can operate independently, or multiple units can be configured into a multipoint system capable of accommodating more than 200 transmitters in RS485 bus configuration. Each unit can transmit a 4-20mA signal or ModBus RTU digital output to any control device or PLC. Units equipped with optional onboard re-lays can operate as stand-alone monitors, activating alarms, horns or fans. They can also shut down a system without needing to be hardwired back to a central control. A relay deactivation feature prevents accidental alarm activation during calibration. Other features include a bright dual-chan-nel split-screen LED display, programmable alarms, and onboard sensor life indicators. Approvals: NRTL/c, Class I, Divisions 1, 2, Groups B, C, D; CSA, Class I, Divisions 1, 2, Groups B, C, D; CENELEC (ATEX), EEx d IIB H2 T5. See below for common configurations, call for others.

Item Description Price7814635-14100 iTransH2S(0-500ppm) $695.007814635-14110 iTransH2S(0-500ppm), w/On-BoardRelays $740.007814635-11000 iTransCO(0-999ppm) $695.007814635-11010 iTransCO(0-999ppm), w/On-BoardRelays $740.007814635-1A400 iTransO2(0-30%) $695.007814635-1A410 iTransO2(0-30%), w/On-BoardRelays $740.007814635-1C200 iTrans,LEL(0-100%)PentaneCal. $695.00I7814635-1C210 iTrans,LEL(0-100%)PentaneCal., w/On-BoardRelays $740.007814635-1C201A4 iTrans,LEL(0-100%)/O2(0-30%) $990.007814635-1C211A4 iTrans,LEL(0-100%)/O2(0-30%), w/On-BoardRelays $1035.007814635-1C20141 iTrans,LEL(0-100%)/H2S(0-500ppm) $990.007814635-1C21141 iTrans,LEL(0-100%)/H2S(0-500ppm), w/On-BoardRelays $1035.00AirAware™

Single-Gas Monitors Industry proven performance combined with a new, low-pro-file design makes the Industrial Scientific AirAware a logical choice for those critical areas that require continuous monitoring but not the environmental protection of an explosion-proof enclosure. Providing discrete monitoring and enhanced aesthetics for more commercial or institutional settings, the AirAware Series is the ideal solution for reliable, low-cost, fixed-point monitoring. The AirAware can be configured to operate as a monitor with local LED display, a controller with on-board relay switching capability, a transmitter with 4-20mA or Modbus RTU outputs, or as a transmitter with on-board relays. Each configuration is designed to meet your specific indoor monitoring needs. Every AirAware is equipped with electrochemical sensing technology, dual alarm LEDs, a digital display providing real-time readings, push-button operation and a NEMA 4 type enclosure. When alarm conditions are met, low/high alarm visual indicators alert users to gas hazards. Standard operating power is 12-24 VDC for the AirAware,

SafeTOX Gas Monitor The SafeTOX Gas Monitor is used in a variety of industrial applications. Easy to install and operate; just apply power to the SafeTOX Gas Monitor and it is ready for operation. SafeTOX Monitor can be applied in any indoor and out-door application where there is a threat of the build-up of combustible gases, the presence of toxic gases, or oxygen deficiency. Designed for maximum performance and reliability.

Housed in a rugged, metal enclosure designed for NEMA 4XDesigned with the sensor mounted external to the enclosure, it is easily replaced by simply unscrewing the sensor housing and removing the plug-in sensorFactory calibrated, making them ready for installation and immediate operationUniquely designed to eliminate all potentiometers, or any other type of internal adjustmentShipped with a unique Sensorgard which protects the sensor from dirt, water, while allowing gas to penetrate into the unit. The Sensorgard also acts as a baffle in windy environments.

Standard features include:Large, 1.75, four-digit LED displayThree levels of alarmLarge LED alarm indicatorsInternal relay contacts for FAULT, CAUTION, WARNING and ALARMA normally-energized fault relay provides a contact output for any condition that would not be considered NORMALFailsafe fault relay outputDiagnostics that appear on the displayAudible alarm4-20 mA output

Item Description Price10062825 CarbonMonoxide0-500PPM $1,970.0010062829 Oxygen0-25% $1,970.0010062842 HydrogenSulfide0-100PPM $1,970.0010062846 Chlorine0-5PPM $1,970.0010062885 Combustiblegas0-100%LEL-Solvents $2,265.00

•

•

•

•

•

••••

•

••••

while a 120 VAC power supply option is available for convenient plug-in monitoring applications. Configure your AirAware to match your needs, adding options. The AirAware is covered by a one-year warranty

Item Description Price68100056-11010 COmonitorw/powersupply,audioalarm $459.0068100056-11100 COcontrolw/audioalarm $509.0068100056-11300 COcontrol/transmitw/audioalarm $539.0068100056-31010 NH3monitorw/powersupply,audioalarm$689.0068100056-31100NH3controlw/audioalarm $739.0068100056-31300NH3control/transmitw/audioalarm $769.0068100056-71010CI2monitorw/powersupply,audioalarm$489.0068100056-71100CI2controlw/audioalarm $539.0068100056-71300CI2control/transmitw/audioalarm $569.0068100056-A1010O2monitorw/powersupply,audioalarm$459.0068100056-A1100O2controlw/audioalarm $509.0068100056-A1300O2control/transmitw/audioalarm $539.00


Beacon 110 Single Channel Wall Mount Controller The Beacon 110 is a powerful, low cost fixed system controller for one point of gas detection. It is microprocessor controlled, versatile, simple to install and operate, and priced to be the industry’s best value single gas detection controller. It is capable of accepting RKI sensors directly for LEL level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide. The Beacon 110 can also accept any 4-20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly at the Beacon 110 housing, or can be wired remote from the controller. The 10 amp rated relays are strong enough to directly power external alarms and horns. The digital display has backlighting and simultaneous readout of the gas type and concentration. The Beacon 110 is also housed in a NEMA 4X rated case for a weather tight seal. This case design complies with lock out / tag out standards and can be fully secured. An external reset switch allows the alarm to be silenced from outside of the controller housing. Ships complete with a wall mounting kit for easy installation.

ApplicationsPetrochemical plants, refineries, water & wastewater treatment, pulp & paper mills

Please call for pricing and configuration. Prices starting at $850.00 Many assembly and direct connect sensors are available with or without a junction box (J-Box).

Beacon 800 Eight Channel Wall Mount ControllerThe Beacon™ 800 is a simplified, versa-tile, low cost fixed system controller for one to eight points of gas detection. It is microprocessor controlled and is capable of accepting up to 8 separate 4-20 mA sensor transmitters, which can be either 2 or 3 wire. The Beacon™ 800 can be powered by either 24 VDC or 115 VAC. It is simple to operate and comes complete with a wall mount installation kit. The 2 large digital displays have backlighting and easily identify both the gas type and the gas concentration for all 8 channels simultaneously. The Beacon™ 800 is also housed in a NEMA 4X rated case for a weather tight seal. This case design complies with the new lock out / tag out standard and can be fully secured. An external reset switch allows alarms to be silenced from outside the controller housing. The bottom mounted wiring hubs allow for easy wiring. With 10 amp rated relays, the Beacon™ 800 can be wired directly to a variety of devices like alarm horns, buzzers, or lights. This eliminates the need for costly external relays from the controller to devices.

Prices starting at $1,995.00Please call for ordering assistance. Please specify the fol-lowing components, Controller, detector assemblies (up to 8) and any options desired such as heavy-duty relay board or individual recorder output board. As always, we offer all the replacement parts and accessories. Need factory start-up or training, please call for quote.

S Series Diffusion Sensor/TransmitterThe RKI “S” series gas sensor/transmitters are highly reliable and very cost effective basic 4-20 mA transmitters for detection of com-mon gas hazards. The “S” series transmit-ters are available for LEL, Oxygen, H2S, CO, or for 0 - 500 ppm Hydrocarbon detection (for various fuels or solvents). The electronics are encased inside a potted package to avoid damage from mechanical abuse or corrosion, and the amplifier is installed inside an explosion-proof enclosure. Sensors for LEL, H2S, CO, and ppm HC are explosion-proof with flame arrestors. The Oxygen sensor utilizes an internal I.S. barrier; so all-5 versions are designed for use in hazardous atmospheres.

The only tools required to calibrate the “S” series are a voltmeter, screw-driver, and cal gas. The zero and calibration functions are performed by adjusting potentiometers on the amplifiers. The amplifier has test jacks for connection of a voltmeter for calibration purposes, and the sensor response is viewed on the voltmeter as a 100mV to 500mV signal. One person can perform Field calibration easily and quickly.

Please call for pricing and configuration.

M2 SeriesStand Alone Explosion Proof Transmitter -This state-of-the-art transmitter that can operate as an independent, stand-alone system or as part of a system connected with an analog or digital signal to virtually any controller, PLC, or DCS. The M2 series detects LEL combustibles, oxygen, hydrogen sulfide, or carbon monox-ide. It utilizes a magnetic wand technique for performing non-intrusive calibration. The M2 provides an automatic zero drift correction features, which results in more stable readings and reduces the need for adjust-ments due to sensor aging. The M2 housing does not need to be opened for zeroing or calibration, making it unnecessary to declassify the area for routine maintenance. Internal push buttons can also be used if the housing is opened. It is designed so that one person can perform a complete field calibration. The stainless steel flame arrestor that covers the sensor (LEL, H2S, CO, or XP Oxygen) is water repellent with a special patented water resistant coating. The M2 provides a 4-20 mA output in addition to a Modbus digital output. It also has two levels of alarm with relays, plus a fail alarm with a relay. A digital display of the gas concentration, as well as alarm and status lights can be viewed through the front window.

Industry ApplicationsPetrochemical plantsRefineriesOffshore drilling platformsWater & wastewater treatment plantsPulp & paper millsGas, telephone, & electric utilitiesParking garagesManufacturing facilitiesAutomotive

Please call for pricing and configuration. Prices starting at $950.00Pricing includes the sensor and explosion proof housing.

•••••••••

INSTR

UM

EN

TS – FIXED SYSTEM

S


SAM

PLIN

G PU

MPS

–

INSTR

UM

EN

TS Escort™ ELF

Sampling PumpThe patented Escort ELF Sampling Pump can be used for personal and area sampling. An internal secondary standard calibrates the pump continuously and needs to be checked against a primary standard only once a month (or every 200 hours for coal mine dust sampling). The state-of-the-art electronic laminar flow sensor, consisting of a laminar flow element and pressure sensor, provides constant flow (volume) control, with +/- 2.5% regulation of flow rate (from 1 to 3 lpm) and automatic compensation for changes in battery voltage, temperature, altitude and sample load.

Approvals and Standards: Escort ELF Sampling Pumps are UL approved as intrinsically safe for use in hazardous locations—Class I, Groups A, B, C, D; Class II, Groups E, F, and G; and Class III, Division I locations. NIOSH certified for coal mine dust sampling (TC-74-030). MSHA certified as intrinsically safe for underground use (Approval No. 2G-3924-1)

Hazards: Nuisance Odor, Particulate and Dust, Toxic Atmosphere Non-IDLH,

Applications: Welding, Chemical, Construction, Mining, Oil and Gas, Sand Blasting, Sanding & Grinding, Spray Painting

Item Description Price805559 EscortELFPumpwithflowfaulindicator, 110Vsingle-unitcharger,GeminiTwin PortSampler,andstandardpackaging $1,079.00805560 EscortELFPumpwithflowfaulindicator,110Vcharger, samplinglineandstandardpackaging $881.00711400 EscortLCPumpwith110Vsingle-unitcharger, samplinglineandstandardpackaging $626.00

ELF Personal Sampling Pump Accessories MSA sampling pump accessories and air sampling equipment allow moni-toring of many different contaminants in various applications. Sampling pump accessories can be used in personal and area sampling for a wide va-riety of airborne contaminants such as asbestos fibers, toxic gases, vapors, particulates, mists and fumes.

Accessories for MSA sampling pumps include filter cassettes, filter media, a cyclone assembly, preweighed filter cassettes, filter holder assemblies, im-pingers, the Gemini@ Twin-Port Sampler, sorbent tubes and calibrators.

Please ask a Mallory Customer Service staff for pricing information.

Dräger TubesAn established method for measuring and detecting contaminants in the soil, water and air. The Dräger-Tube method of measurement is used for investigating soil pollution, for investigating liquid samples, and for air analysis. More than 500 substances can be detected and measured using the Dräger-Tube system. Typical applications include the monitoring of work-place air, emission measurements, quality control, process control, and monitoring of compressed air for breathing apparatus, as well as environ-mental and hazardous substance detection applications. Sold 10 per box.

Item Description Price6406010 Chlorine0.20-10.0ppm $57.506406020 Ammonia10.0-150ppm $57.506406030 Benzene0.20-10.0ppm $162.506406070 CarbonDioxide1,000-25,000ppm $55.506406080 CarbonMonoxide5.0-150ppm $55.506406090 HydrochloricAcid1.0-25.0ppm $74.006406100 HydrogenCyanide2.0-50.0ppm $69.006406110 SulfurDioxide0.40-10.0ppm $57.506406140 HydrochloricAcid20.0-500ppm $74.006406250 Toluene10.0-300ppm $73.006406260 Xylene10.0-300ppm $69.006406310 Propane100-2,000ppm $82.506406320 Trichloroethylene5.0-100ppm $69.006406400 Phosphine0.10-2.5ppm $73.006406450 WaterVapor0.40-10.0Mg/l $84.506728071 Benzene5/b5-50ppm $61.008101831 HydrogenSulfide1/d1-200ppm $55.50Ch23501 CarbonDioxide0.1%/a0.1-6Vol.% $55.50Ch25601 CarbonMonoxide5/c5-700ppm $57.50

Accuro Gas Detector PumpThe accuro gas detector pump is a manually operated bellows pump that draws a calibrated 100 milliliter sample through the short-term Dräger-Tubes.

One-Hand OperationVery Low MaintenanceEnd-of-Stroke IndicatorBuilt-in automatic Stroke Counter

Item Description Price4056443 Hardsidekit $581.794053473 Softsidekit $527.14

Accuro 2000 Battery Powered Gas Detector PumpDrager’s battery powered gas detector pump that is used in combination with the Accuro pump allowing “hands-free” operation of the Dräger-Tube System.

Programmable Stroke CountOne-Button OperationVery Low MaintenanceUp to 2000 stroke operationLightweight (> 5 lbs / 2.4 kg)

Item Description Price4500200 Hardsidekit $1,183.93

••••

•••••


INSTR

UM

EN

TS – SAM

PLING PUMPS &

TUBES

RAE Piston Hand Pump RAE Systems’ Hand Pump is for use with the Rae line of Gas Detection Tubes. The Hand Pump, along with the Tubes, offers quick, on-the-spot measurements of many gases and vapors at low cost without the need for calibration.

Solid metal construction with RAE Systems’ exclusive lifetime war-rantySpringless piston design for accurate 50 and 100 cc volumesTube tip breaker and glass tip holderClear end-of-flow indicatorTapered inlet design avoids leaks with different diameter tubesSimple stroke counterAdditional accessories include remote sampling hoses with 15’ (5 m) or 35’ (11 m) lengths

Tubes sold separately.

Item Description PriceLP1200 PistonHandpump $165.00

•

••••••

Colorimetric Gas Detection Tubes RAE Systems’ large selection of Colorimetric Gas Detection Tubes offer quick, on-the-spot measurements of many gases and vapors at low cost. The tubes are easy to read with a sharp, clear color change and provide accuracy with no need for calibration. An asterisk (*) in the list below indicates boxes containing 5 colorimetric tubes and 5 pre-tubes, for a total of 5 measurements. Standard boxes without the asterisk have 10 tubes.Many other Specialty Tubes available.

Description Item Standard RangeAcetone(C3H6O) 10-111-40 0.1-2%Amines(RNH2) 10-132-10 0.5-10ppmvAmmonia(NH3) 10-100-05 1-30ppmv 10-100-10 5-100ppmv 10-100-12 0-260ppmv 10-100-15 25-500ppmv 10-100-40 1-15%Benzene(C6H6) 10-101-01* 0.5-10ppmvselective 10-101-10* 5-40ppmvselective 10-101-20 5-100ppmvButane(C4H10) 10-137-30 25-1400ppmvCarbonDioxide(CO2) 10-104-30 300-5000ppmv 10-104-40 0.05-1% 10-104-45 0.25-3% 10-104-50 1-20% 10-104-60 5-40%CarbonMonoxide(CO) 10-102-18 5-100ppmvselective 10-102-20 5-100ppmv 10-102-30 20-500ppmv 10-102-45 0.2-4%Chlorine(Cl2) 10-106-10 0.5-8ppmv 10-106-20 5-100ppmvChlorineDioxide(ClO2) 10-130-10 0.25-15ppmvDieselFuel&JetFuel 10-143-10 0.5-25ppmvEthanol(C2H6O) 10-141-30 100-2000ppmvFormaldehyde(CH2O) 10-121-05 0.1-5ppmvGasoline(CnHm) 10-138-30 30-1000ppmvHydrocarbons(HC) 10-110-30 50-1000ppmvHydrogenChloride(HCl) 10-108-09 1-20ppmv 10-108-10* 1-20ppmvw/desiccant 10-108-22 20-500ppmvw/desiccantHydrogenCyanide(HCN) 10-126-10 2.5-60ppmvHydrogenFluoride(HF) 10-105-10 0.5-20ppmvHydrogenSulfide(H2S) 10-103-04 0.2-3ppmv 10-103-05* 0.2-3ppmvw/desiccant 10-103-06 1-7ppmv 10-103-10 2.5-60ppmv 10-103-10 10-120ppmv 10-103-18 25-250ppmv 10-103-20 50-800ppmv 10-103-30 100-2000ppmv 10-103-40 0.1-2% 10-103-50 2-40%

Description Item Standard RangeMEK-MethylEthylKetone(C4H8O) 10-113-20 0.02-0.6%Mercaptans(RSH) 10-129-20 5-120ppmvMethylBromide(CH3Br) 10-131-10 1-18ppmvNitrogenDioxide(NO2) 10-117-10 0.5-30ppmvNitrogenOxides(NOx) 10-109-20* 1-50ppmvOzone(O3) 10-133-03 0.05-0.6ppmvPhenol(C6H6O) 10-139-05 1-25ppmvPhosphine(PH3) 10-116-10 5-50ppmv 10-116-20 25-500ppmv 10-116-25 50-1000ppmvSulfurDioxide(SO2) 10-107-15 2-30ppmv 10-107-20 5-100ppmv 10-107-25 100-1800ppmv 10-107-30 200-4000ppmv 10-107-40 0.2-5%Toluene(C7H8) 10-114-20 10-300ppmvTrichloroethylene(C2HCl3) 10-119-20* 5-100ppmvVinylChloride(C2H3Cl) 10-128-10* 1-20ppmvWaterVapor(H2O) 10-120-10 2-10lbs/MMCF 10-120-20 6-40lbs/MMCF 10-120-30 0.05-1.0mg/L 10-120-40 1-18mg/LXylene(C8H10) 10-112-20 10-200ppmv 10/tubes/box$30.00 10bxs.$270.00


SAM

PLIN

G PU

MPS

& T

UBES

–

INSTR

UM

EN

TS

Gastec Gas Sampling Pump Kit with Thermal RingPacked with features, the Gastec Gas Sampling Pump is the only pump you need for measuring gas and vapor concentrations quickly and accurately. Small, lightweight, and rugged, this pump is perfectly calibrated, displays ambient temperature, and includes a lifetime warranty. It is simple, always ready, and intrinsically safe. The Gastec Detector Tube and Pump System has been designed specifically with the end user in mind to allow for ease of use without compromising safety. Weighing only 8 ounces, the intrinsically safe pump can easily be transported to any test site. The pump body is contoured and covered with a soft elastomer for a comfortable, secure grip. The exterior of the pump is composed of a durable and non-corrosive plastic and synthetic rubber compound, effectively eliminating any risk of sparks should the pump system be accidentally be dropped into an explosive environment. The pump incorporates a built-in detector tube tip breaker with a durable diamond cutting edge. Discarded tips are deposited in a storage bin for easy disposal. The fail-safe handle can be locked into two positions: the full stroke position for a sample volume of 100 ml or the half stroke position for a sample volume of 50 ml. Both positions are marked by means of an unambiguous red line thereby eliminating the chance of taking an incom-plete pump stroke. The flow finish indicator in the handle ensures precise sampling volumes. The small diameter of the pump piston allows it to be pulled out with less effort than many competitors’ pumps.

Item Description PriceGV-100-S-TR GasSamplingPumpComplete (GastecGasSamplingPumpwithThermal RingandCarryingCase;includessparepartskit (1lubricantand3rubbertubeholderswithfilter), GastecDetectorTubeHandbook,andAccessories brochure)REPLACESGV-100-S $270.00GV-100-SOHA-TR GV-100-S-TRwithOne-HandAdapter $338.00GV-100-X GastecGasSamplingEconomyPump (DoesnotincludeGastecDetectorTube HandbookorFlowFinishIndicator; Full100mlpumpstrokesonly) $129.00

Detector TubesWhether for a routine inspec-tion or a HazMat emergency, you can count on Nextteq’s complete line of Gastec Detector Tubes to precisely identify and measure gases and vapors—over 600 ap-plications. The list below shows the tubes most generally used in the Pulp and paper industry. Many more are available, so please ask if you don’t see what you need. Available in boxes of 10 tubes, items marked with (*) are sold with 5 detector tubes and 5 pre-tubes.

Item Description Range Price92 Acetaldehyde 5-750ppm $56.5092L 1-20ppm $59.5092M 2.5-100ppm $56.50191 Acrylonitrile 2-360ppm* $56.50191L 5-100ppm $56.503L Ammonia .5-78ppm $55.003LA 2.5-200ppm $55.003M 10-1000ppm $55.003H .2-32% $57.002H CarbonDioxide .5-20% $55.002HH 2.5-40% $55.002L 0.13-6% $55.002LC 100-4000ppm $56.502LL 300-5000ppm $55.001L CarbonMonoxide 2.5-2000ppm $55.001LC 1-30ppm $55.501LL 5-50ppm $55.501LK 5-600ppm $55.501M .05-5% $57.001H 0.1-10% $56.501HH 1-50% $56.508HH Chlorine 0.25-10% $59.508H 25-1000ppm $56.508LA 0.16-16ppm $55.008LL 0.025-2ppm $56.5023L ChlorineDioxide 0.025-1.2ppm $56.5023M 0.1-10pm $57.0091 Formaldehyde 2-100ppm* $55.5091L 0.1-40ppm $55.0091LL 0.05-1ppm $57.0091M 8-6400ppm $57.00185 Hydrazine 0.05-2ppm $57.0012H HydrogenCyanide 0.05-1-6% $57.0012L 0.36-120ppm $57.0012LL 0.2-7ppm $56.5012M 17-2400ppm $59.5032 HydrogenPeroxide 0.5-10ppm $59.504LL HydrogenSulfide 0.25-120ppm $54.004L 1-240ppm $54.004LT 0.1-4ppm $54.004LB 0.5-12ppm $55.004LK 1-40ppm $55.004M 12.5-500ppm $55.0071 MethylMercaptan 0.25-140ppm $56.5071H 20-2700ppm $57.00124 Styrene 10-1500ppm $55.5010 NitricOxides 2.5-200ppm $55.005H SulfurDioxide 0.5-8% $57.005L 1.25-200ppm $56.5035 SulfuricAcid 0.5-5mg/m3 $56.50


INSTR

UM

EN

TS – SAM

PLING PUMPS &

TUBES • SPECIALTY KITS

Gastec Dosimeter Tubes and Tube HoldersDirect-reading tubes use diffusion to obtain fast, accurate measurement of air contaminants. No need for motorized or hand pumps, charts, or laboratory analysis to determine results. Each hermetically sealed glass tube contains a reagent sensitive to a specific gas or vapor. The reagent is contained in a fine-grain absorbing media.

To use, snap off the marked “easy break” end of a tube and insert in tube holder. The gas or vapor to be measured immediately enters the tube and reacts with the absorbing media to produce a quantitative color stain. Gas concentration is shown by the length of stain, and the measurement is precisely indicated on a single calibration scale printed on each tube. Simply divide that number by the number of hours exposed to obtain a time-weighted average (TWA) concentration. The diffusion process offers a clean, clear line of demarcation.

May be used for sampling periods ranging from 30 minutes to 48 hours, allowing continued sampling with the same tube even if overtime is required (avoiding added costs or potential sampling error).

Lightweight tube holder clips easily to clothing for breathing zone mea-surements without the need for sampling pumps. Serves as an all-in-one tube tip breaker and holder, minimizing the amount of equipment neces-sary to perform a test. Pack of three holders.

Dosimeter TubesGastec Dosimeter Tubes provide simple, pre-calibrated, direct-read TWA (time-weighted average) monitoring of airborne chemicals. Whether for personnel or area monitoring, Gastec provides users with 3 times more applications than competitive dosimeter tube systems. Sold 10 per box.

Item Description Range Price112D Ethanol 100-25000ppm $62.60122DL Toluene 2-500ppm $62.6012D HydrogenCyanide 1-200ppm $62.60132D Trichlorethylene 3-300ppm $62.60133D Tetrachlorethylene 3-150ppm $62.6014D HydrogenChloride 1-100ppm $62.60151D Acetone 5-1500ppm $62.60152D MethylEthylKetone 2-600ppm $62.60174D 1,3Butadiene 1.3-200ppm $62.6017D HydrogenFluoride 1-100ppm $62.601D CarbonMonoxide 1.04-2000ppm $62.601DL CarbonMonoxide 0.4-400ppm $62.602D CarbonDioxide 0.02-12% $62.608D Chlorine 0.08-100ppm $62.60

Other tubes are available.

Tube BreakerThe Tube Breaker Deluxe offers a detector tube tip breaker with a durable diamond cutting edge. Discarded tips are deposited directly into a built-in storage bin, preventing glass fragments from scattering and improving safety. It holds up to 260 broken tips.Small and durable, the Tube Breaker Deluxe easily fits in the gas sampling pump carrying case or in your pocket.

Item Description Price721 TubeBreaker $39.95

Field Soil Test Equipment and Soil Detector TubesThe Gastec Field Soil Test Equipment makes analyzing ground contaminants fast and convenient. Plumes can be easily and quickly delineated from leaking underground tanks or chemical spills. The items ready to use anytime, anywhere— no extra equipment, lab analysis, or testing is necessary.

The rugged Boring Pole enables you to create sampling holes up to 33 1⁄2 inches (80 cm) deep. Plumes can be easily and quickly delineated from leaking underground tanks or chemical spills.

Item Description PriceGV-100-S-TR GastecGasSamplingPumpKitWiththermalring, carrycase,3rubberTubeholderswithfilters, lubricant,GasDetectortubehandbook $270.00360 SoilSamplingExtensionProbe $210.00361 BoringPole $350.00

Soil Replacement Detector TubesSold 10 per box.

Item Description Range Price121 Benzene 2.5-120ppm $59.00134 Carbontetrachloride 0.5-60ppm $59.00132Ll Trichloroethylene 0.375-6ppm $59.00101L Gasoline 30-2000ppm $59.00133M Tetrachloroethylene 0.5-75ppm $59.00122 Toluene 5-600ppm $59.00132M Trichloroethylene 2-250ppm $59.00123 Xylene 5-100ppm $59.00

Solution Detector TubesGastec Solution Detector Tubes provide fast, economical, on-the-spot detection of trace chemicals in liquids. Tubes are avail-able to detect a variety of chemicals with broad measuring ranges.

The tubes are easy to use and do not require mixing, pumps, calibration, equipment, or accessories. Simply place a tube in a con-tainer with the target solution. Results are available in moments. Sold 10 per box.

Item Description Range Price211 SulfideIon-solution 1-100ppm $54.60211H SulfideIon-solution 10-1000ppm $54.60211LL SulfideIon-solution 0.5-20ppm $54.60211M SulfideIon-solution 2-300ppm $54.60222 FreeResidualChlorine 0.1-10mg $54.60271 Mercury-solution 1-20mg/l $54.60273 Chromium(VI)Ion 0.5-50mg/l $54.60281 IronIon-solution 5-50mg/l $54.60284 CopperIon-solution 1-20mg/l $54.60285 Zinc-solution 3-20mg/l $54.60291 Nickel-solution 5-50mg/l $54.60


TEST

ING

KITS

• DO

CKIN

G ST

ATIO

NS –

IN

STR

UM

EN

TS

Galaxy Automated Test SystemFor use with Solaris®, Sirius® and Orion® InstrumentsThe Galaxy Automated Test System works without the touch of a single button. Simply place the instrument in the test stand and the system performs the test automatically; no user intervention is required. The Galaxy System is completely standalone; it does not require a computer or network interface for any mode of operation.

For the fully featured version of Galaxy Automated Test System, an op-tional network interface is available for either wired (Ethernet) or wireless (802.11b) networks. The Galaxy interface for data retrieval and reporting is extremely easy to use. Any web navigator can be used to access the data of a network-enabled Galaxy Automated Test System. Calibration and bump check records, due date for instrument calibration, and the ability to email MSA directly for support are just a few of the capabilities of this interface.

Very Low Total Cost of OwnershipThe Galaxy Automated Test System will help lower the overall total cost of ownership of your MSA gas detection instruments. With the automated record-keeping capabilities that are available with each Galaxy Test Stand, there’s no need to keep hand-written records of an instrument’s calibration history.

Ideal for: Domestic preparednessFire fightingGas detection Hazardous materials

Hazards:Combustible atmosphereConfined spaceLeak detection Oxygen deficiencyToxic atmosphere IDLHToxic atmosphere Non-IDLH

VersatileMultiple System Interconnectivity

Item Solaris Kit Sirius Kit Orion KitBasic Standalone Kit

BasicSystem 10061051 10061050 10061824

Standard Standalone Kit (includes Regulator) StandardSystem 10061051 10061050 10061824

Please call for pricing and list of all the other model numbers and options available.

••••

••••••

Clandestine Lab KitsA complete kit ready to go for Law Enforcement or Hazmat teams. Contains Gastec Model GV-100 Pump Kit (GV-100S-TR) with Thermal Ring, Gastec Detector Tube Handbook, Hard Shell Car-rying Case, Acid gases tubers (80), Ammonia tubes (3L), Hydrogen chloride tubes (14L), Phosgene tubes (16) and Phosphine tubes (7L). Note, kit contains one box of each type of Gastec tubes listed in description. Each box contains 10 tubes.

Item Description Price50140000 ClandestineLabKit $850.00

Replacement tubes (10 per box)

Item Description Range Price80 AcidGases 1-80ppm $59.003L Ammonia 0.5-78ppm $58.0014L HydrogenchlorideSEI 0.2-76 ppm $57.0016 Phosgene 0.05-20ppm $59.007L Phosphine 0.15-5 ppm $60.00

Water Analysis KitsGastec Water Analysis Kits provide precise, on-the-spot measurement of chlorinated hydrocarbons using headspace analysis. The kits are available to detect trichloroethylene, tetrachloroethylene and 1,1,1-Trichloroethane. Each kit includes a Gastec Gas Sampling Pump and a box of 10 Gastec tubes, plus a sampling bottle, plastic beaker, thermom-eter, instructions and carrying case. For replacement tubes, order Water Analysis Detector Tubes. Sold 10 per box.

Item Description PriceWPT132 TrichloroethyleneKit $335.00WPT133 TetrachloroethyleneKit $335.00WPT135 TrichloroethaneKit $335.00

Replacement Water Analysis Detector Tubes (10 per box)123M Trichloroethylene $56.50133M Tetrachloroethylene $56.50135L 1.1.1Trichloroethane $56.50


INSTR

UM

EN

TS – DOCKING STATIONS

DS2 Docking Station™

Automatic instrument calibration, record-keeping, diagnostics and rechargingAutonomous, stand-alone Instrument Docking Stations (IDS)Network up to 100 IDS units through Ethernet cable or wireless con-nectionGraphical user interface to monitor facility-wide networkMulti-lingual displayUtilizes a central database for storage of instrument data

The DS2 minimizes customer time required to manage post-purchase responsibilities and reduces liability. The next generation of automated calibration, record-keeping, diagnostics and recharging, the DS2 Dock-ing Station™ features two-way communication with a Docking Station Server that manages up to 100 IDSs through Ethernet or wireless connec-tions. Freestanding, self-contained IDSs, each with a multi-lingual LCD display, status LEDs, and an audible alarm, allow plant-wide distribution for autonomous operation, or up to 5 IDSs can be grouped together to share calibration gas cylinders. Stores instrument data in a central database.

Item Description Price18105551-AB+ DS2iTXInstrumentDockingStation $1,795.0018106302-AB+ DS2GasBadgeProDockingStation $1,795.0018105544-AB+ DS2T82InstrumentDockingStation $1,795.0018105569-AB+ DS2VX500InstrumentDockingStation$1,795.00

+ Ordering information: A = Wireless Compact Flash (0-none, 1-installed +$125.00) B = number of iGas Readers at $45.00 eachNOTE: Calibration gas and regulator not included.

•

•

•

•••

M-Cal Calibration Station Simple, push-button operationFunction (bump) testingCalibrationBattery rechargingStand-alone operation…no PC requiredAutomatic documentation via PC or printer interfaceCompatible with M40 software version 4.0 and higher

The M-Cal Calibration Station is capable of calibrating, function (bump) testing, and charging the M40 instrument as well as the M40/SP40 instrument pump combination. Available in single- and six-unit versions, the M-Cal can be ordered in any configuration of bays for M40 or M40/SP40 combinations. A serial connector provides simple connection to a serial data printer for hard-copy printout of each calibration and bump test. Battery-powered kits allow the M•Cal to be portable in remote areas.NOTE: Calibration gas and regulator not included.

Item Description Price18105965-100 Single-UnitM-Cal,M40Bay $795.0018105965-010 Single-UnitM-Cal,M40/SP40Bay $795.0018105973-AB0 Six-UnitM-Calw/powercord $1595.00

NOTE: The 0 is for NA plug which will be the case. Add below the line after the final part number. A = # of M40 Bays (0-6), B = # of M40/SP40 Bays (0-6)

•••••

•

•

Cal Plus™ Calibration System

Stand-alone operation – no PC requiredSimple, push button calibration or function (bump) testingImmediate report generationBuilt-in printer optionMultilingual LCD displayWall mountable (wall- mounted gas cylinder holder available)

With the new Cal Plus™ Calibration Station, calibrating and bump testing the GasBadge™ Plus monitor has never been easier or more cost effective. The Cal Plus™ features simple, two-button operation allow-ing the user to quickly and easily calibrate or function (bump) test the instrument. The large LCD display and the LED indicators then show whether or not the instrument passed or failed the desired function.

A PC is not required to operate this stand-alone system, making the unit extremely portable and flexible. When used with a PC, Cal Plus™ soft-ware generates calibration and bump test reports that are automatically downloaded via a standard USB connection. The unit also downloads alarm events and instrument details, allowing the user to quickly and eas-ily configure instrument preferences.

The Cal Plus™ is available with a built-in dot-matrix printer that auto-matically prints calibration and bump test reports. The reports provide permanent documentation of instrument serial numbers, pass/fail indica-tions, bump test readings, and full span readings for the GasBadge® Plus.NOTE: Calibration gas and regulator not included.

Item Description Price18106344-00 CalPlus™CalibrationStation $795.0018106344-10 CalPlus™CalibrationStation w/on-boardprinter $1,095.0017117714 Serialdatathermalprinterwith infraredinterface $395.0017117722 Serialdatadotmatrixprinter, 120VACpowered $395.0018102163 CalibrationGas–CarbonMonoxide, 100ppm,103L $135.0018100859 CalibrationGas–HydrogenSulfide, 25ppm,58L $158.0018102219 CalibrationGas–NitrogenDioxide, 5ppm,58L $380.0018102222 CalibrationGas–SulfurDioxide, 5ppm,58L $158.0017124348 Wallmountedgascylinderholder $45.0018102509 DemandFlowRegulator $340.00

•

•

•

•••


DOCK

ING

STAT

IONS

–

INSTR

UM

EN

TS Biosystems IQ Express Docking Station

The ToxiPro/Ltd IQ Express Dock-ing Station is an automatic calibration station and data download center for the ToxiPro and ToxiLtd single- sen-sor gas detectors. Just drop the detector(s) into the IQ Express and the IQ Express does the rest in as little as 20 seconds†. The IQ Express is a fully automated bump test station that performs up to eight critical tests every time an instrument is placed in the dock. If an instrument fails the bump test, the IQ Express will automatically initiate a full span calibration without further interven-tion from the user. Total processing time with a full span calibration is still under one minute†. O

2, CO and H

2S models; Other sensor types may

take longer.

Standard versions of the IQ Express dock are capable of processing ToxiPro and ToxiLtd instruments containing: O

2, CO, H

2S and SO

2. En-

hanced versions of the IQ Express Dock are capable of processing ToxiPro and ToxiLtd instruments with all of the sensors listed above plus ToxiPro instruments with Cl

2, NO

2, NH3, HCN and PH

3 sensors.

Automated Tests:Automatic Instrument IdentificationAutomatic Battery TestAutomatic Alarm TestsAutomatic Bump TestAutomatic Calibration (if necessary)Automatic Record KeepingAutomatic Ready/Fault Indication

Configuration Options:Docks can operate as independent calibration stations.Docks can be connected to a PC via USBDocks can be connected to a PC via Network

PC Control:Connect the dock to PC via USB Port or Network for enhanced con-trol over calibrations and data acquisition.

Efficient and economical:Bump test in less than 20 secondsCalibration in less than 1 minute

All IQ Express Docks include PC software, installation discs and instruc-tion manuals.

Item Description PriceIQ Express Docking Station

54-46-9000 Standardversion $495.0054-46-9100 Enhancedversion $595.0054-46-9000N Standardversion,Ethernetready $595.0054-46-9100N Enhancedversion,Ethernetready $695.0054-46-8000 IQExpressMountingBracket $150.0054-46-8001 IQExpressPoweredMountingBracket $200.00

•••••••

•••

•

••

AutoRAE An auto-calibration; bump test and charging system for RAE Systems gas monitors. AutoRAE cradles are available for the QRAE, QRAE Plus, MultiRAE Plus, EntryRAE and MiniRAE 2000.

Press the button once for a bump test, twice for calibration, and walk away. A few minutes later, easy-to-read LEDs inform you of the status of the gas monitor’s sensors. If the monitor fails the bump test, the system automatically performs a calibration.

Simple to operate, this PC-free version is highly portable. Consisting of one controller plus cradles, the system accommodates up to 10 cradles. It is easy to add cradles when the job demands it, and it is easy to add controllers, expanding one system into several systems.

Automatic calibrationAutomatic bump testAutomatic chargingPC-free, pushbutton easyMonitors always calibrated and chargedIncreases user confidence and safety

Available in a variety of configurations.

Please call 1-800-MALLORY for pricing and ordering assistance.

••••••

MultiPro IQ Express Docking StationThe MultiPro IQ Express Docking Station is an automatic calibration station and data download center for the MultiPro gas detector. Just drop the detector into the dock and the MultiPro IQ Express does the rest. The MultiPro IQ Express is a fully automated bump test station that performs up to eight critical tests every time an instrument is placed in the dock. If an instrument fails the bump test, the MultiPro IQ Express will automatically initiate a full span calibration without further intervention from the user.

Automated tests:Automatic instrument identificationAutomatic battery testAutomatic alarm testsAutomatic bump testAutomatic calibration (if necessary)Automatic record keepingAutomatic ready/fault indication

Configuration options:Docks can operate as independent calibration stationsConnect docks to a PC via USB

PC control:Connect the dock to PC via USB Port for enhanced control over calibrations and data acquisitionEthernet-ready system also available

All MultiPro IQ Express Docks include PC software, installation discs and instruction manuals.

Item Description Price54-49-9000 IQExpressDockingStation $795.0054-49-9000N IQExpressDockingStationwith Ethernetreadysystem $895.00

•••••••

•

•

•

•


INSTR

UM

EN

TS – SPECIALTY INSTRUM

ENTS

HazRAEHazRAE is a hazardous materials decision support application for chemical, biological, and WMD assessments that runs on handheld, wireless devices. It was developed to address the unique needs of first respond-ers determining unknown hazards.

The HazRAE database contains more than 91,000 chemical, biologi-cal warfare, and bioterror agents, trade names, and improvised explo-sive devices. Materials can be retrieved using tradi-tional search identifiers such as name or UN number, but when no standard identifiers are present or known (particularly a concern when responding to terrorism), HazRAE is able to identify unknown chemicals using observable physical characteristics and signs and symptoms observed in victims.

HazRAE includes integrated response information for more chemical agents (TICs, TIMs, CW agents), biological agents (bio-weapon and bio-terror agents), and improvised explosive devices than all the other legacy systems combined!

HazRAE provides Improvised Explosive Device (IED) standoff distances and an evacuation calculator. The application includes a database of two times more explosives than other systems.

Key Features:Identify a broad range of agents via observed physical properties such as medical signs and symptomsIdentify chemical reactions through HazRAE by virtually mixing agents and modeling their chemical reactionsFive times more biological agents than any other mobile systemIntegrated Correction Factors for RAE Systems 9.8 eV, 10.6 eV, and 11.7 eV PIDs found in MultiRAE Plus, MiniRAE 2000, and ppbRAE PlusSpecific emergency life support/first aid for chemical and biological agents

Item Description Price055-5000-000 HazRAEPDAKit $2,295.00055-3001-000 NeckLanyardKit $29.95055-3002-000 Beltclipforcase $19.95

Please call for information and pricing on software and Combo kits - many configurations are available for the Haz-RAE systems.

•

•

••

•

E-Cal: Professional Instrument Management Dräger E-Cal is the revolu-tionized cost-saving instru-ment system, which auto-matically operates customized calibrations for all portable Dräger gas detection instruments. The new instrument management standard: Automatically calibrates and checks up to 10 instruments simultaneously, controls up to twelve different gases, provides maximum efficiency and functionality, includes automatic data management (calibration history), incorporates modern and modular design, automatically reads instruments’ datalogger, auto-matically loads instruments’ charges, is compatible with Multiwarn II, MiniWarn and Pac III.

Dräger E-Cal: MasterStationThe MasterStation is the control center of the Dräger E-Cal system. It supports up to 10 instrument modules at once and is available in 2 dif-ferent versions. The MasterStation 6 controls a maximum of six different gases, the MasterStation 12 up to twelve.The MasterStations are computer controlled and ensure that any testing and calibration is carried out fast, efficient and with the utmost degree of accuracy.The control center can communicate bidirectional and simultaneously supports different instrument types. This means the number of configura-tion possibilities of Dräger E-Cal is almost infinite.

Dräger E-Cal ModuleThe instrument module establishes the communication between the gas detection de-vice and the MasterStation/PC. It automatically detects when an instrument is put in and reports this event to the control software CC-Vision Dräger E-Cal.The instrument module con-trols the gas supply so that an adequate gas flow to the instru-ment is always ensured.The test or calibration result is displayed as well. Moreover, the instrument module can also be used in combination with the regular instrument wall plug charger to recharge the unit. Following instrument modules are available:

MultiWarn IIMiniWarnPac IIIPac Ex 2

Every instrument module can be operated manually and independent of the MasterStation and utilized as an economic alternative for simple instrument bump tests.

Dräger E-Cal: Module AdapterThe optional module adapter enables the direct control of a single instrument module via the PC without using a MasterStation. This way it allows Dräger E-Cal to be used as an economic station for testing and calibration incl. automatic documentation of the test results for single instruments.

Please Call for pricing and additional Information.

••••


SPEC

IALT

Y IN

STRU

MEN

TS –

IN

STR

UM

EN

TS

RDK (Rapid Deployment Kit) System PackageThe Rapid Deployment Kit (RDK) is designed for quick assessment and management of gaseous threats. The kit includes four wireless 5-gas, AreaRAE monitors with in-case charging as well as the Host Controller for monitoring from a command center up to two miles away. The system can scale up to 32 AreaRAEs with the addition of Detector Kits, each con-taining 4 AreaRAEs. The RDK offers first responders and environmental managers all the detection tools they need in two rugged carrying cases.

The AreaRAE monitors can be rapidly deployed and re-deployed in situ-ations that require a quick and adaptable response. They can be arranged in a perimeter to detect chemical hazards and to monitor the environ-mental safety of a large public event. The units help response teams gain control over potentially perilous situations by assessing the environment and determining the geographic disbursement of hazardous gases and chemicals. Housed in a military-grade self-contained case, the RDK is easy to transport and easy to deploy.

The RDK also provides protection in the monitoring of environmental remediation, oil, gas platforms, petrochemical applications, and refiner-ies. The AreaRAE can detect gaseous VOCs, LEL, O

2, H

2S, and CO and

offers datalogging for event documentation.

The RDK is available with two additional options:Global Positioning Satellite (GPS) option: Includes the ability to track and display readings from up to 32 remotely located detectors on a GPS mapGamma Radiation option: A Gamma radiation sensor replaces one of the toxic gas sensors on the AreaRAE units (see the AreaRAE Gamma product description for more details)

An “RDK System Package” contains the following:RDK Detector Kit - contains 4 AreaRAEs, spare batteries, and calibra-tion kit, with in-case chargingRDK Host Controller Kit - contains laptop, host controller with pre-loaded ProRAE Remote Software, and host controller RF modem, all wired to operate in-case

Plese call for volume pricing and additional information.

•

•

•

•

AreaRAE GammaThe AreaRAE Gamma is a combination toxic gas and gamma radiation detector equipped with a wireless RF (radio frequency) modem that allows the unit to communicate with and transmit sensor and GPS readings on a real-time basis to a remotely located base controller located up to 2 miles away.

In stand-alone operation, the AreaRAE Gamma is a rugged, weatherproof, one-to-five sensor portable monitor that can run up to 24 hours on either rechargeable Lithium-ion or optional alkaline batteries. It is also the first “lunchbox” type multi-sensor instrument able to include a gamma radiation sensor for measurement of gamma radiation, a photo-ionization detector (PID) for parts-per-million measurement of volatile organic compounds (VOCs), and an LEL combustible gas sensor, oxygen sensor, and selectable electrochemical toxic sensor.

The RF modem allows real-time data transmissions with a base controller located up to two miles (3.2 km) away from the AreaRAE Gamma detec-tor. A personal computer can be used as the base station. The standard ProRAE Remote software used to control AreaRAE Gamma systems is capable of monitoring the input of up to 32 remotely-located monitors.

Key Features:Up to four gas sensors (PID, LEL, O2 and selectable toxic gas)One radiation sensor (Gamma)Loud buzzer and large, extra-bright warning lightReal-time wireless data transmission with built-in RF modemView real-time sensor data and alarm status at headquarters or com-mand centerLicense free, ISM band RF transmission with communication range up to 2 milesFully hardware and software compatible with standard AreaRAE 5-gas monitoring systemStandard AreaRAE is factory upgradeable to AreaRAE GammaRugged, weatherproof housing (IP55)Built-in sampling pumpInterchangeable Li-ion or alkaline battery pack

Call for more information on ordering and accessories

•••••

•

•

••••

LifeShirtThe LifeShirt was created to meet the needs of first responders, HazMat work-ers, firefighters, industrial cleanup crews, and homeland security. The LifeShirt is a durable, lightweight chest strap embedded with sensors that continuously collect life sign information. Breath rate, heart rate, activity, posture and skin temperature are all monitored by the sensors in the strap. The LifeShirt with the RAELink2 Modem*, easily integrates into an AreaRAE Wireless Network for real-time remote monitoring and data collection at a remote command center, where a commander can simultaneously monitor mul-tiple team members. All of the collected data is stored and can be used for post-event analysis.*All components sold separately.

Item Description Price039-L200-000 LifeShirt $4,000.00


INSTR

UM

EN

TS – SPECIALTY INSTRUM

ENTS

PlumeRAEReleases of toxic materials present first responders with an immediate challenge – determining what actions need to be taken to protect nearby populations. They must answer a number of questions:

Where is the toxic plume headed, and in what concentration?What areas need to be evacuated?Who should shelter in place?What roads should be closed?How do we prioritize actions with limited resources available?

Industry leaders RAE Systems, SAFER Systems and Coastal Environmental Systems have teamed to create PlumeRAE - a unique, turn-key solution that allows rapid monitor-ing and assessment of situations involving the release of hazardous substances. PlumeRAE gives first responders information to make crucial decisions.

Plume Measurement:GPS-equipped AreaRAE wireless monitors placed in strategic locations measure the levels of critical toxic chemicals and communicate their measurements to a ProRAE Remote Base StationProRAE Remote, running on a standard laptop computer, feeds this information to the Plume Measurement Software that is running on the same PCWeather data transmitted by a Coastal Environmental Systems WEATHERPAK® completes the information package needed for analysisThe Plume Measurement Software, developed by SAFER Systems, integrates the information and shows users a picture of the toxic plume, the speed at which it is spreading, and the concentration of the toxic compound

Decision Support:PlumeRAE gives first responders the information they need along with decision support so that they can answer critical questions and take im-mediate, effective action. First Responders can:

Track and validate plume impactEmploy intelligent placement tactics for safely locating respondersEvaluate the toxicological effect on responders and the communityCreate emergency response strategyUnderstand how long the event will persistSave the event for post-event analysis

Please call for information on ordering and accessories.

•

••••

•

•

•

•

••••••

iNet Instrument Network™

Industrial Scientific combines the ground-breaking, two-way communi-cation technology of its DS2 Docking Station™ with the capabilities of the Internet to offer iNet — a completely automated and comprehensive gas monitor management solution. In addition to providing all the Dock-ing Station functions of automated calibration, recharging, instrument diagnostics and record-keeping, iNet remotely monitors the condition of the instrument fleet and automatically handles any necessary service requirements based on the service plan selected.

iNet Exchange™ Program - If a malfunction is detected, a ready-to-use replacement exchange instrument will be delivered by 5 p.m. the next business day. Customer returns failed instrument in pre-paid shipping package.

iNet Parts™ Program - If a malfunction is detected, Replacement part(s) will be delivered by 5 p.m. the next business day. Customer installs part(s) to restore equipment to proper working condition.

iNet Exchange™ and iNet Parts™ Programs - includes: Continuous monitoring of your instrument fleet via the Internet - Industrial Scientific monitors and automatically initiates any service requirement — no action required by you to initiate service Providing weekly instrument status reports covering: Days since last calibrationOverdue calibrations Sensors with marginal span reserves Age of sensors Missing instruments Continuous monitoring of calibration gas cylinder pressure Automatic notification of an instrument malfunction If a malfunction is detected, replacement part(s) are delivered by 5 p.m. the next business day. Customer then installs part(s) to restore equipment to proper working condition. All repair parts and freight are included Asset tracking by serial number Secure off-site storage of your data Additionally, iNet Parts™ Program includes the following start-up and commissioning services: Installation and setup of the Docking Stations™, Server and Instru-ments as well as system testing and training Travel expensesFreight

iNet Monitoring Service™ Program - Offered as a stand-alone option to the complete gas monitor management capabilities of iNet. An annual subscription to this service, gives you a weekly e-mail status report on the condition of your instrument fleet. Utilizing the automated calibration, recharging, instrument diagnostics and record-keeping func-tions of the DS2 Docking Station™, Industrial Scientific will monitor for low, empty or expired calibration gas, marginal or failed sensors, and days since last calibration. If a problem is detected between weekly reports, you will receive an immediate report to notify you of the problem. Payments can be made on an annual or monthly basis. Call 800-MALLORY to order or for more information.

•

•••••••••

••••

•

••


SPEC

IALT

Y IN

STRU

MEN

TS –

IN

STR

UM

EN

TS Portable Air Filtration

System for Supplied-Air RespiratorsBiosystems TravelPanel 50MP is a portable air filtration system designed to provide Grade-D breathing air for 1 to 4 workers using supplied-air respirators. The TravelPanel 50MP can supply 50 cubic feet per minute of puri-fied air, and regulates the outlet pressure to comply with NIOSH requirements for your respirator.

Designed to purify compressed breathing air, the Biosystems TravelPanel 50MP removes water, oil, and particulates as small as 0.01 microns, organic substances and odors.

The built-in MultiPro™ gas detector automatically monitors outlet air for CO (carbon monoxide) contamination. If the TravelPanel 50MP is equipped with the optional O

2 sensor, it will also monitor the level of ox-

ygen in the supplied air. When the levels of CO or O2 surpass the pre-set

alarm levels, the alarm will be sounded to notify users that a potentially unsafe condition exists. The MultiPro in the TravelPanel 50MP offers a blackbox data recorder, calibration reminder, and one-button calibration as standard features.

The TravelPanel 50MP is portable and requires no AC power to operate. Output pressure is adjustable to the respirator manufacturer’s recommen-dations. As a precaution, the outlet pressure is automatically limited to 125psi, the NIOSH maximum.

HousingRugged, durable, lightweight and portable

Dimensions58 cm x 41 cm x 23 cm23” x 16” x 9”

Weight25 lbs.

TravelPanel 50MP sample configurations are shown below.Please call for pricing and more options. Full array of accessories avail-able.

Item Description Price54-50-100NS TravelPanel50MP,MultiProwithCOsensoronly, noadditionalalarmoptions,rechargeablebattery, Schraederoutletfittings,nosecondaryoptions, YellowCase $1,895.0054-50-300NH1 TravelPanel50MP,MultiProwithCOandO2 sensors,noadditionalalarmoptions,rechargeable battery,Hansenoutletfittings,MultiPro DataloggerUpgrade,YellowCase $2,060.0054-50-331NH3B TravelPanel50MP,MultiProwithCOandO2 sensors,withLEDStrobeLight,LockingStabilizer Bars,withLowPressureAlarmoption, rechargeablebattery,Hansenoutletfittings, MultiProDataloggerUpgradeandDustcovers, BlackCase $2,460.00

•

••

•

Biosystems CO Response Kit Biosystems CO Response Kit is the complete and accurate solution for both residential and workplace carbon monoxide calls. Use the ToxiVision or ToxiPro CO moni-tor to check the atmosphere, and then leave a ToxiTube dosimeter tube behind to continue monitor-ing for CO for the next 24 hours.

Residential and workplace carbon monoxide callsBuilt with the fire service in mindEverything you need to calibrate and operate the ToxiVision10 ToxiTube dosimeter tubes that can be left behind to continue moni-toring for an additional 24 hours.

Item Description Price54-37-01RK ToxiVisionCOResponderKit $725.0054-37-01 ToxiVisionCOGasDetector $395.0054-38-11 Replacement10-PackToxiTubes $69.0054-9036 Replacement34-litercylinderCOCalGas $75.00

••••

Confined Space Kits These Confined Space Kits con-tain all the tools necessary to test the atmosphere prior to entering a confined space, assuring safe entry. Confined Space Kits come in economy, deluxe and professional versions. All kits include a charger, training video and carrying case. Your choice of monitor determines the additional accessories that are included in each kit. Economy kits include constant flow hand pump. Deluxe and Professional kits include motorized sampling pumps. Professional kits include calibration equip-ment. The iTX Professional and VX500 kits include the charger/datalink with datalogging software. All kits come housed in a durable, easy-to- transport carrying case. See below for kit contents and ordering informa-tion. The E, P, D in the item number denotes Economy, Professional or Deluxe Kit.

Item Description PriceEconomy iTX

iTX-Kit-E11014 LEL,O2,H2S,CO,Li-ion,120V $2,105.00iTX-Kit-E11F00 LEL,O2,CO/H2S,Li-ion,120 $1,935.00iTX-Kit-E11100 LEL,O2,CO,Li-ion,120V $1,860.00iTX-Kit-E11400 LEL,O2,H2S,Li-ion,120V $1,860.00iTX-Kit-E11000 LEL,O2,Li-ion,120V $1,610.00

Professional iTXiTX-Kit-P11014 LEL,O2,H2S,CO,Li-ion,120V $3,265.00

Deluxe iTX – iTX-Kit-D11014LEL,O2,H2S,CO,Li-ion,120V $2,910.00iTX-Kit-D11100 LEL,O2,CO,Li-ion,120V $2,580.00iTX-Kit-D11400 LEL,O2,H2S,Li-ion,120V $2,665.00iTX-Kit-D11000 LEL,O2,Li-ion,120V $2,415.00

Deluxe VX500 – VX-Kit-D10610.6Lamp,Li-ion,120V $4,227.00


INSTR

UM

EN

TS – SOUND LEvEL M

ETERS

Humidity/Thermometer StopwatchMonitor Worker Heat StressDesigned to track heat stress on workers. This is an easy way to monitor the environment by check-ing exposure levels and how hot it feels when humidity is combined with the actual temperature.

Digital up/down timer displays temperature, humidity, and heat indexUser settable heat index alarmStopwatch/chronograph mode with 1/100-second resolutionFastest/slowest/average lap recall99-lap counter with 30-lap/split memory10-hour countdown timer with audible beeper warning for the last 5 secondsProgrammable alarmCalendar mode displays day, month, and date

Item Description PriceHW30 Humidity/Thermometerstopwatch $39.99

•

••

•••

••

Sound Level MetersExtech sound meters include all the features/functions needed for basic noise level surveys or to meet the requirements for OSHA compliance, community noise ordinances, or machine noise evaluation. All Extech instruments can be purchased factory-cali-brated with a Certificate of Calibration traceable to N.I.S.T. (National Institute of Standards Technology).

Digital Sound Level MeterAnalog bar graph with 50 dB range updates every 40 ms±2 dB accuracy with 0.1 dB resolutionA+C weightingAC analog outputRecord max/min values over timeUtilizes 0.5” (12.7 mm) electret condenser microphone40 to 130 dB measuring range

Item Description Price407730 DigitalSoundLevelMeter $79.99407730NIST DigitalSoundLevelMeterw/certificate $204.99

•

•••••

•

Sound Level Alert with AlarmBuilt-in LEDs alert user when sound level is too high or too low.Ideal for hospitals, auditoriums, schools and other areas where there is a need for being alerted when sound level reaches a set point.

Bright LEDs (red flashing or green) alert user when sound level is too high or too low - LEDs can be read from 100 ft (30 m)Continuous monitoring of sound level Wall, desk or tripod mount with optional 15ft (5 m) microphone extension cable for remote monitoringUser settable high or low limit (30 to 130 dB) with output to drive external relay moduleMeets ANSI Type 2 and EN 60651 accuracy specs - compliant to OSHAGreen housing w/110V adapt

Item Description PriceSL130G SoundLevelAlert $249.99

•

••

•

•

•

16,000-point Datalogging Sound Level MeterType 2 meter with datalogging memory for 16,000 records plus PC inter-face and software

High accuracy meets ANSI and IEC 651 Type 2 standardsLarge LCD with fast 50 segment bargraph displayStored data can be transferred to a PC via RS-232 interfaceReal time and date are logged with data; Max Hold functionTripod mount is ideal for field use

Item Description Price407764 Type2SoundLevelMeter w/datalogging/PCinterface $599.99407764NIST Type2SoundLevelMeterw/certificate w/datalogging/PCinterface $714.00

•

•

•

•

•

Sound Level Meter with Backlit DisplayTwo-range meter with backlit LCD display. Comes complete with microphone, wind screen and 9V battery.

High accuracy meets ANSI and IEC 651 Type 2 standardsHigh and low measuring rangesLow: 35 to 100 dBHigh: 65 to 130 dBData Hold and Max Hold functions

Item Description Price407732 Type2SoundLevelMeter $149.99407732NIST Type2SoundLevelMeterw/certificate $274.99

•••••

Sound Level Meter with PC InterfaceBig backlit display, PC interface and background sound absorber

High accuracy meets ANSI & IEC 651 Type 2 standardsBackground noise absorber for machine noise measure-ments, filters ambient noiseRS-232 interface for capturing data directly to a PCLarge display with backlighting and analog bargraphMin/maxAnalog AC/DC outputs for connection to a recorderTripod mount is ideal for field use

Item Description Price407750 SoundLevelMeter $249.99

••

•••••


SOUN

D LE

vEL

MET

ERS

• FIT

TES

TER

–

INSTR

UM

EN

TS

OHD Fit Tester 3000The OHD FitTester 3000 is the fastest and most accurate method of quantitative fit testing on the planet. With ease of use, speed of testing, and proven accuracy, why would you trust anything else?Compatible with the following respirator brands, adapter fittings are required in some cases.

3M AO Safety Avon Protection Bacou/Dalloz/Willson Bullard/Sabre Cairns Draeger Glendale/Bilsom Interspiro ISI Kemira Lab Safety Life Air MSA Moldex North ProTech RSI Scott Sundstrom Survivair US Safety US Military

How does a Fit Tester Work? The OHD FitTester 3000 operates on the principle of Controlled Negative Pressure (CNP). Negative pressure created inside air purifying respirators during inhalation is the driving force that causes air contaminants to leak into the respirators. Contaminant leakage paths result from such things as poor facepiece-to-face seals, dirty inhalation valves, or faulty cartridge gaskets. CNP fit test technology is designed to directly measure air leakage into respirators by creating and maintaining the same driving force that causes contaminant leakage.

The Department of Homeland Security’s Center for Domestic Preparedness has selected the OHD FitTester 3000 as the instru-ment to use for training respirator fit testing in the US. This group consists of law enforcement, fire fighters, EMS, public works, EMA and all first line defenders who respond to public dangers dealing with WMD, chemical, biological, radiological devices.

doseBadge Personal Noise DosimeterThe doseBadge is the unique way to measure occupational and indus-trial noise exposure. Different from traditional noise dosimeters, the doseBadge has no cables or buttons, and is controlled via an infrared link from the RC:110A Reader unit. The new 110A doseBadge adds new functions and features as compared to the former 100B Badge. These new features allow the doseBadge to be used to comply with a range of measurement guidelines and stan-dards including ISO, OSHA & OSHA HC, US DOE, ACGIH and US ACHPPM.

Small and lightweight No cables or controls-reduces the risk of damage, misuse or tampering Simple operation provides effective measurements doseBadge controlled via infrared from the (included) RC:110A Reader unit Rechargeable NiMH battery power for the doseBadge Time History Data Logging

Item Description PriceCR110A doseBadgedosimeter $1,108.50

••••

••

Cirrus Safety Manager’s KitEverything you need for noise measuring in one package. The kit includes doseBadges to measure individual noise exposure, a Cirrus 700 Series Type II sound level meter, calibrator, and software, all in one convenient carrying case. The doseBadge dosimeter is wireless, tamper-proof, and simple to operate. The unobtrusive dosimeter stores up to 16 hours of readings. Now available in an intrinsically safe version. This Safety Manager’s Kit was designed specifically with safety professional in mind. Many other kits are available, please ask.

Item Description PriceSMK2 SafetyManager’sNoiseMeasurementKit withCK:720B&CK:110A/2 $6,575.00

OHD/Cirrus Sound Level Meters These meters are ideal for Noise at Work Assessments, Noise Control, and Environ-mental Measurements The need for simple, accurate noise mea-surements for both industrial and environ-mental use produces a requirement for a robust measurement tool. Instruments that can be used quickly and easily while providing information accurately and precisely can be supplied to users to allow regular periodic or continuous recording of information.

Integrating Averaging Sound Level Meter, with Leq, LEPd (LEX8h), Sound Level, Lmax, Lmin, LCPeak, Ln’s and Frequency Analysis Data logging of measured parameters Large measurement memory Up to 1,300 measurements and 8 days of time history Large graphical display New tactile keypad Menu driven operation Advanced configuration options from the Deaf Defier3 software New Deaf Defier3 Windows software Outdoor measurement kits availableOptional 1:1 and 1:3 octave band filters IEC 61672-1:2003 Class 1 or Class 2 Group X IEC 60651 & IEC 60804The CR:250 series of instruments is available in two versions: The CR:251B conforms to the requirements of Type 1 of IEC 60651, while the CR:252B conforms to the requirements of Type 2. The main physical difference between the units is in the microphone and preamplifier assembly. The CR:251B is supplied with a remov-able preamplifier as standard; allows the instrument to be used with extension cables. The AC and DC outputs allow the CR:250 series to be used as a front end for additional measurements systems and data recording applications. The CR:252B and CR: 251B can be supplied as complete measurement kits

Contact Mallory today for a complete list of available units.

•

•••••••••••••

•

Please call for additionalinformation and pricing

importance of understanding the atmospheric … of understanding the atmospheric composition ......

Documents