importante - steren.com.mx · user manual motion sensor with wireless bell installation of the bell...
TRANSCRIPT
MANUAL DE INSTRUCCIONES
Sensor de movimiento con campana inalámbrica
IMPORTANTE
PRECAUCIONES
INSTALACIÓN DEL SENSOR
INSTALACIÓN DE LA CAMPANA MODO DE USO
COLOCACIÓN DE LA BATERÍA
ESPECIFICACIONES
Antes de utilizar el producto, lea cuidadosamente este instructivo para evitar cualquier mal funcionamiento.La información presentada sirve únicamente como referencia sobre el producto. Debido a actualizaciones pueden existir diferencias. Consulte nuestra página web www.steren.com para obtener la versión más reciente de este manual.
• Siempre utilice un paño seco y suave para limpiar el dispositivo.
• No lo use ni lo almacene en lugares donde existan goteras y salpicaduras.
• No coloque objetos pesados sobre el dispositivo.
• Evite las caídas del equipo; podría sufrir daños severos.
• Este producto NO es un juguete; manténgalo fuera del alcance de los niños.
Con cuidado retire la base como se muestra en la imagen.
Retire la tapa del compartimento.
Retire la tapa del compartimento.
Sensor
Campana
Inserte 3 baterías “AAA”. Tenga cuidado con la polaridad.
Inserte 2 baterías “AAA”. Tenga cuidado con la polaridad.
Utilice la base para realizar marcas de perforación sobre la superficie donde va a instalar el sensor.
Haga una marca de perforación sobre la superficie donde va a instalar el dispositivo. Deslice el interruptor hacia la posición . Cada vez que el sensor detecte
movimiento una alarma se escuchará por aproximadamente 5 segundos.
Deslice el interruptor hacia la posición . Cada vez que el sensor detecte movimiento sonará la campana con el tono seleccionado.
Coloque nuevamente el sensor sobre la base.
Monte la campana sobre el tornillo.
En la campana elija la melodía y el volumen del tono de alarma.
Alarma local
Alarma remota
Realice las perforaciones. Inserte taquetes y atornille la base.
Si conecta un adaptador de corriente, considere el largo del cable.
11
1
2
1
1
2
2
2
2
3
3
3
Alimentación sensor: 4,5 V - - - (3 x AAA) 9 V - - - 250 mA (con convertidor)
Alimentación Campana: 3 V - - - (2 x AAA)Frecuencia de transmisión: 314,93 MHz
Consumo: 0,2 W/hConsumo en espera: 0,05 W/h
Las especificaciones pueden cambiar sin previo aviso
Realice la perforación. Inserte un taquete y luego coloque un tornillo cuidando que sobresalga algunos milímetros de la pared .
VolumenMelodía
USER MANUAL
Motion sensor with wireless bell
INSTALLATION OF THE BELL
Sensor
If you connect it with a AC adapter, consider the length of the cable.
Carefully remove the base as shown below.
Remove the cover. Insert 3 “AAA” batteries. Ensure that the polarity is correct.
1 2 3
IMPORTANT
CAUTIONS
INSTALLATION OF THE SENSORBATTERY PLACEMENT
HOW TO USE
Before to use the product, please read carefully this manual to avoid any malfunction. The info in this manual is shown as reference.Due to updates can exist differences. Consult our website www.steren.com to obtain the current version of this manual.
• Always use a soft and dry cloth to clean it.
• Don’t use or store the device in places where exist water or splashes.
• Don’t place heavy objects over the
• Avoid dropping the device, it could cause severe damage.
• This product is NOT a toy; keep it away from children.
Set the sensor into the base again.
Use the support to make drill marks into the surface where you want to install the device.
Drill. Then insert anchors and screw the base into the surface.
1 2
3
SPECIFICATIONS
Remove the cover.Bell
Insert 2 “AAA” batteries. Ensure that the polarity is correct.
Make drill mark into the surface where you want to install the device.Slide the switch toward position. Each that the sensor detects movement, the alarm will be hear approx 5 seconds.
Slide the switch toward position. Each that the sensor detects movement, the alarm will be hear with the selected tone.
Place the bell over the screw.
In the bell choose the melody and the volume level of the alarm tone.
Local alarm
Remote alarrm
1
Sensor input: 4.5 V - - - (3 x AAA) 9 V - - - 250 mA (with power converter)
Bell input: 3 V - - - (2 x AAA)Transmission frequency: 314.93 MHz
Consumption: 0.2 W/hStand-by power consumption: 0.05 W/h
Specifications may change without notice
1
1
2
2
2
3
Drill. Then insert an anchor and screw, ensure that the screws sticks out from the wall some milimetres.
VolumeMelody