F l e x i b l e T 1 / e 1 A d d / d r o p M U l T i p l e x e r

Bayly Communications Inc. W www.bayly.com

OmniPlexer

OMNIPlexer is an extremely rugged add/drop T1/E1 multiplexer designed for very high efficiency over thin-route networks with many customers declaring it the best primary multiplexer they have ever used.

OMNIPlexer is deployed in every type of telecom network including the criti-cal infrastructure of airports, highways, railways, army, air force, navy, coastguard and police as well as wireless network operators, television stations and carriers to private telecom applications including oil/gas pipelines, power utilities and govern-ment.

Remote management of each OMNIPlexer in a network is available using the RACS (Remote Access and Control System) Communications Manager. RACS provides local and remote control over all operating parameters, including voice and data ports, T1 and E1 ports, as well as comprehensive T1/E1 alarms and per-formance monitoring information.

The OMNIPlexer excels in its simplicity and broad range of channel inter-faces and is noted for the number of competitive products it has replaced.

Improve bandwidth utilization and efficiency in critical infrastructure

A versatile and cost-effective multiplexer tailored for thin-route and polling applications

APPLICATIONS

n Transportation nAirports n Highways nRailways nPort Authoritiesn Security n Army n Air Force n Navy n Coast Guard n Police

Bayly enables the networks of the world’s best companies

BENEFITS

n Reliabilityn Flexibilityn SimplicitynRuggedness

n Government and Utilities nState and Local government n Electric Utilities nOil and Gas companies nWater pipelinesn Carrier n Wireless Mobile n Public Carrier

SPECIFICATIONS

Network Ports T1 E1 Line Rate: 1.544 Mbps, +/- 30 ppm 2.048 Mbps, +/- 50 ppm Line Code: AMI or B8ZS HDB3 Equalization: None required for up to 6dB cabale loss Line Impedance: 110 ohm balanced 75 ohm unbalanced or 120 ohm balanced Synchronization: Internal, Slave, Loop Timed, or Exturnal LED Alarm Indicators: T1 Major and Minor E1 Prompt and Service Alarm Contacts: Dry Form C, Major and Minor Dry Form C, Prompt and Service Connectors: 50 Pin Amphenol BNC (75 ohm), 50 Pin Amphenol (120 ohm) Capatibility: Bellcore Pub. CCITT G.732 43801 & 62411 CCITT G.703

VOICE CHANNEL INTERFACES:4-wire & 2-wire E&M Trunk-Signalling Types, I, V, and PLR2-wire Subscriber & Exchange Signalling (FXO/FXS)Omnibus 4W E&M, 2W FXS with DTMF decoding

DATA CHANNEL INTERFACES:Synchronous: 600 bps-64 Kbps, RS232/V.24, sub-rate V.110 64 Kbps-V.35, RS422/V.11, Co/contra-directional N x 56/64 Kbps-V.35, RS422Asynchronous: 300 bps-38.4 Kbps,RS232/V.24, sub-rate V.110 Point-to-Multipoint 0-19.2 Kbps, RS232/V.24

REMOTE MANAGEMENT:VT100-based using one DS-0 (T1) or 2 bits in time slot 0 (E1).Multipoint communications channel enables all OMNIPlexers to be managed using minimal bandwidth.One RACS Communications Manager required with each OMNIPlexerOne SNMP RACS Communications Manager system required with each OMNIPlexer for OMNIView NMS.

FIBER OPTIC INTERFACE:850/1300 nm multimode and 1300/1550 nm single mode fibre, 20 dB loss budget, ST connector

POWER SUPPLY:Input voltage: -48 VDC, (optional power card redundancy)Connector: Screw terminalsIntegral Ring GeneratorExternal Converters available for 24 VDC and 110/220 VAC operation

ALARMS:Major (Prompt) and Minor (Service) Alarms, 2 Amp Form “C” dry contacts

MECHANICAL:19 or 23 inch relay rack, flush or centre mountHeight: 10.5 inches (266 mm)Depth: 14.5 inches (368 mm)

ENVIRONMENTAL:Operating Temperature: 0° to +50° CStorage Temperature: -25° to +70° CHumidity: to 95% non condensing

FEATURES

n Extremely rugged, highly reliablen Easy to usenRedundant powernHot swappable modulesnPoint-to-multipointnSubrate multiplexing and channel re-usenSNMP managednFull Remote Access and Controln Wide variety of channel interfaces

OmniPlexer