ind.i/o datasheet - industruino · industruino ind.i/o is the arduino-compatible equivalent of a...
TRANSCRIPT
Mounting on 35 mm DIN rail, 4 spacing units wide
Standard input voltage 12V / 24Vpermissible range, lower limit (DC) 8 Vpermissible range, upper limit (DC) 28 VTime of day
Number of digital inputs 8 (shared with digital outputs)Type of digital input Galvanically isolated serializer with interruptInput voltage range 0-28VLogic HIGH voltage >11VLogic LOW voltage <3VMaximum trigger frequency 10 KHzProtection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients.
Number of digital outputs 8 (shared with digital outputs)Type of digital output Galvanically isolated high-side driver (Charge pump NFET)Output voltage range Tied to supply voltage (6.5-32V)Maximum current per output 2.6 AMaximum total current 6.5 AMaximum switching frequency 400 HzProtection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients.
Number of analog inputs 4Type of analog inputs Buffered ADCRange of voltage measurement 0-10VRange of current measurement 0-20mASwitching of voltage / current mode Automatic - in softwareResolution 18BitConversion rate 18bit: 3.75 Hz - 16bit: 15 Hz - 14bit: 60 Hz - 12bit: 240 HzProtection of analog inputs ESD, transients.
Number of analog outputs 2Type of analog outputs Buffered DACRange of output voltage 0-10VRange of output current 0-20mASwitching of voltage / current mode Automatic - in softwareResolution 12BitUpdate rate 20 KHzProtection of analog outputs Short-circuit, over-current, over-temperature, ESD, transients.
Isolation topology Isolated from MCU and analog field sectionDuplex type Half duplexNumber of receivers on bus 32Data rate 1 Mbps
Isolation topology Isolated from digital and analog field sectionNumber of pins 14Voltage level 5VProtocols supported SPI, I2C, UART, 9 GPIO'sProtection of expansion port ESD, transients.
LCD 128x64 pixel FSTN with dimmable backlightPush buttons 3 - push button membrane panel
Protection class IP20Ambient operating temperature 0 - 55 °C
Width 71.5 mmHeight 87 mmDepth 58 mmWeight 150 g
Document updated: 8.03.2015
Installation
Supply voltage
Digital inputs
Dimensions
Analog inputs
Analog Outputs
Digital outputs
Communication portsRS485
Expansion port (direct MCU control)
User Interface
Enviromental
Ind.I/O Datasheet
Industruino Ind.I/O is the Arduino-compatible equivalent of a PLC. The interface board offers 8 channels of 24V I/O, 4 channels of 0-10V/4-20mA 18bit ADC, 2 channels of 0-10V/4-20mA 12bit DAC, isolated RS485 transceiver, isolated power zones.
-dustruino and analog peripherals, the GND line of the analog section should be tied to the GND
*When operating in an electrically noisy environment it is possible to use a seperate power supply for your analog peripherals. This will improve the stability of your analog input/output
analog supply’s GND line.
*The majority of IND.I/O board functions are controlled via i2c, therefore it requires the “Indio” Arduino library which can be found on our website’s support page.
https://industruino.com/page/techcentre
2x CHOUTPUT
EXPANSION PORT14 pin IDC
6.5-32V 8x CHPOWER-IN Digital INPUT/OUTPUT
RS485
D0/R
XD2
/SDA
D7 D4/A
6D1
0/A1
0SC
LK/D
15M
ISO
/D14
D1/T
XD3
/SC
L
D6/A
7D5
/PW
M
ISO
2M
OSI
/D16
+5V
4-20 mA 0-10 V
Analog
4x CHINPUTAnalog
V+ CH1
CH1
CH1
CH2
ISO1
ISO1
CH2
CH3
CH4
CH2
CH3
CH4
CH5
CH6
CH7
CH8
40
1
6.5-32 V
Analogzone
MCUzone
Digitalzone
Ind.I/O Baseboard Pinout
Notes
Date: 02.06.2017
INDUSTRUINO IND.I/O - PRODUCT DATASHEET. JUNE 2017Industruino is an Arduino compatible industrial controller. www.industruino.com