infiniti; telematics service information
TRANSCRIPT
1/25
Classification: Reference: Date:
EL12-013n ITB12-011n June 24, 2019
TELEMATICS SERVICE INFORMATION
APPLIED VEHICLES: APPLIED SYSTEMS:
2013 JX35 (L50) 2013 M37/M56 and M35 Hybrid (Y51) 2013 QX56 (Z62) 2014-2019 Q50 (V37) 2014-2018 Q50 Hybrid (V37) 2017-2019 Q60 (V37) 2014-2019 Q70 (Y51) 2014-2018 Q70 Hybrid (Y51) 2017-2019 QX30 (H15) 2019 QX50 (J55) 2014-2019 QX60 (L50) 2014-2018 QX60 Hybrid (L50) 2014-2019 QX80 (Z62) Vehicles equipped with factory Navigation system
SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. A table has been provided on the next page that lists the model- and year-specific steps required to
successfully configure a TCU after it has been replaced. A check OFF sheet has been provided on page 21 to print and check off steps as they are performed.
Please staple the completed Check OFF Sheet to the repair order. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle.
This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
2/25 ITB12-011n
REQUIRED ACTIONS BY MODEL AND YEAR
IMPORTANT: After TCU replacement (steps 1-14):
If all of the steps below are not completed, telematics services will not operate properly.
Follow all of the model/year specific steps in this bulletin and use the Check OFF Sheet provided at the end of this bulletin (page 21).
If the TCU is replaced and the steps were not followed, the warranty claim will be denied.
ORDER OF COMPLETION 1st 2nd 3rd 4th 5th
Model Year Write VIN Configure
TCU Register I-Keys
Turn ON TCU
Register TCU with SXM
JX35 2013
M37/M56 and M35 Hybrid 2013
QX56 2013
Q50 and Q50 Hybrid 2014-2015
2016-2018
Q50 2019
Q60 2017-2018
2019
Q70 and Q70 Hybrid 2014-2017
2018
Q70 2019
QX30 2017-2019
QX50 2019
QX60 and QX60 Hybrid 2014-2016
2017-2018
QX60 2019
QX80 2014-2017
2018-2019
3/25 ITB12-011n
TABLE OF CONTENTS:
Required Actions by Model and Year ..……………………………………… page 2
TCU Replacement ………………………………………………………………. page 4
Check OFF Sheet …………………………………………………….…………. page 21
Manually Enter VIN Data ………………………………………………………. page 22
SOS Light Diagnosis Information ….………………………………………… page 23
NOTE: If the green SOS light is OFF, or has turned OFF, the vehicle may no longer be in Dealer Demo Mode and SXM has disabled all services. The vehicle will need to be enrolled for customer use. Do NOT replace the TCU.
Turning ON the TCU During PDI (2013-2017 Applied Vehicles ONLY)..… page 24
NOTE: If the “Turning ON the TCU During PDI” procedure is not followed correctly, the vehicle cannot be used in Dealer Demo mode or enrolled in Infiniti Connection® or Infiniti InTouch Services™. Should this occur, the “Turning ON the TCU During PDI” procedure will need to be performed again.
4/25 ITB12-011n
TCU REPLACEMENT NOTE:
Each TCU is registered to a specific Vehicle Identification Number (VIN). TCUs cannot be “swapped” between vehicles. Once a TCU is registered to a vehicle, the TCU cannot be used in another vehicle.
During this procedure, Intelligent Key Registration must be performed for the vehicles listed in this
table. You MUST have ALL customer keys collected.
2016-2019 Q50 2017-2019 QX60
2016-2018 Q50 Hybrid 2017-2018 QX60 Hybrid
2017-2019 Q60 2018-2019 QX80
2019 QX50
The new/replacement TCU must come from Nissan North America parts supply.
Some vehicles require TCU Configuration after replacement. Refer to step 20 on page 9.
The VIN MUST be written to the replacement TCU after installation.
The replacement TCU must be registered with SXM. Save VIN Data 1. Set the parking brake. 2. Connect the C-III plus VI to the vehicle. 3. Turn the ignition ON. 4. Launch C-III plus on the CONSULT PC.
5/25 ITB12-011n
Figure 1
Figure 2
5. Select Diagnosis (One System). 6. Select Telematics.
Step 6
Step 5
6/25 ITB12-011n
Figure 3
Figure 4
Figure 5
7. Select Work Support. 8. Select SAVE VIN DATA. 9. Select Start. 10. Select Start.
NOTE: If the VIN data cannot be saved, you will have to manually enter the VIN later in this procedure.
Step 7
Step 8
Step 9
Step 10
7/25 ITB12-011n
Figure 6
Remove the Original TCU 12. Remove the TCU from the vehicle. Refer to the ESM for removal information.
For PDF ESM: section AV–Audio, Visual & Navigation System
For Web ESM: DRIVER INFORMATION & MULTIMEDIA > AUDIO VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU
Step 13 must be performed AFTER the original TCU is removed from the vehicle and BEFORE the replacement TCU is installed.
13. Write down the following information:
Figure 7
11. Select End.
VIN.
International Mobile Equipment Identity Number (IMEI) of the original TCU. This number is located on the TCU.
IMEI Number of the replacement TCU. This number is located on the TCU.
Step 11
LABEL ON TCU
8/25 ITB12-011n
Install the New TCU 14. Install the new / replacement TCU into the vehicle. Refer to the ESM for installation information.
For PDF ESM: section AV–Audio, Visual & Navigation System
For Web ESM: DRIVER INFORMATION & MULTIMEDIA > AUDIO VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU
Write VIN to TCU 15. Connect C-III plus and navigate to Telematics Work support.
Refer to steps 1-7 on pages 4-6.
Figure 8
Figure 9
16. Select WRITE VIN (SAVED DATA).
NOTE: If VIN DATA could not be saved in step 10, proceed to Manually Enter VIN Data on page 22.
17. Select Start.
18. Select Start.
Step 16
Step 17
Step 18
9/25 ITB12-011n
Figure 10
20. Is the vehicle in the table below?
YES: Proceed to step 21.
NO: Proceed to step 31 on page 12.
2016-2018 Q50 * 2017-2018 Q60
2016-2018 Q50 Hybrid * 2017-2019 QX30
2018-2019 Q70 2019 QX50
2018 Q70 Hybrid 2018-2019 QX80
* For 2018 vehicles, TCU Configuration is needed only if the TCU ID number begins with “2047” (see Figure 17 on page 12).
Configure TCU
Figure 11
19. Select End.
Step 19
Step 21
21. Select Re/programming, Configuration.
NOTE: C-III plus screens for steps 22-24 are not shown.
22. Read the precautions on C-III plus screen
and then select Next. 23. Select the model and model year. 24. Select Select, and then select Confirm.
10/25 ITB12-011n
Figure 12
Figure 13
25. Select TELEMATICS. 26. Select After ECU Replacement.
Step 26
Step 25
11/25 ITB12-011n
Figure 14
Figure 15
Figure 16
Step 27
Step 28
Step 29
Step 30
27. Select Manual selection. 28. Select the applicable Type ID:
For 2016-2018 Q50 and Q50 Hybrid:
28277-1HK0A
For 2018 Q70 and Q70 Hybrid:
28277-5UV0A
For 2019 Q70:
28277-6FL2A
For 2017-2018 Q60:
28227-5CA2A
For 2017-2019 QX30:
28277-5DA2A
For 2019 QX50:
28277-6FL1B
For 2018-2019 QX80:
28277-6FL1C
NOTE: If C-III plus automatically selects the Type ID, there will be no options shown under Type ID and Figure 15 will not display. Skip to step 30.
29. Select Next. 30. Select OK.
12/25 ITB12-011n
Write New SIM ID Number on the Repair Order 31. Write the new SIM ID number on the repair order.
a. Navigate C-III plus to the screen shown in Figure 17.
Diagnosis (One System) > TELEMATICS > ECU Identification
b. Locate the SIM ID number and write it on the repair order as “New SIM ID”.
Figure 17
xxxxxxxxxxxxx xxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx
xxxxxxxxxxx
SIM ID number
13/25 ITB12-011n
Intelligent Key Registration (some vehicles) 32. If needed, perform Intelligent Key registration for all customer keys.
The vehicles listed in this table require Intelligent Key registration.
2016-2019 Q50 2017-2019 QX60
2016-2018 Q50 Hybrid 2017-2018 QX60 Hybrid
2017-2019 Q60 2018-2019 QX80
2019 QX50
Refer to the C-III plus operations manual for key registration instructions.
If the vehicle you are working on is not listed in the above table, key registration is not needed.
NOTE: The Remote Engine Start and Stolen Vehicle Locator features (if so equipped) will not function if Intelligent Key registration is not completed, and DTC B130C will be stored.
14/25 ITB12-011n
Turn ON TCU 33. Make sure the vehicle is not in shipping mode (shipping mode = extended storage switch pulled OUT).
If needed, use the following steps to confirm the vehicle is not in shipping mode:
a. Make sure the ignition is OFF.
b. Open the driver’s door and leave it open.
c. Locate the interior fuse panel and remove the cover.
d. Push the white extended storage switch IN.
e. Turn the ignition ON.
f. Turn the ignition OFF.
g. Wait at least 2 seconds, and then turn the ignition ON.
h. Make sure the extended storage warning message is not displayed in the combination meter/display.
34. Connect the C-III plus VI to the vehicle. 35. Set the parking brake and confirm the ignition is ON. 36. Launch C-III plus on the CONSULT PC.
Figure 18
37. Select Diagnosis (One System).
Step 37
15/25 ITB12-011n
Figure 19
Figure 20
Figure 21
38. Select Telematics. 39. Select Work Support. 40. Select TCU ACTIVATE SETTING. 41. Select Start.
Step 38
Step 39
Step 40
Step 41
16/25 ITB12-011n
Figure 22
Figure 23
42. Select Start. 43. Select On to turn ON the TCU. 44. Make sure Current status is On. 45. Select END.
Step 42
Step 45
Step 43
Step 44; make sure current status is ON
On
17/25 ITB12-011n
TCU Registration The following items must first be completed before calling Infiniti Customer Care (SXM), or services may not function properly:
New / replacement TCU is installed in the vehicle.
WRITE VIN (SAVED DATA) has been completed.
If needed, Manual TCU Configuration has been performed.
If needed, all customer Intelligent Keys have been registered.
The TCU is turned ON.
IMEI number for original and replacement TCU is written on the repair order.
SIM ID number for the replacement TCU is written on the repair order. 46. Call Infiniti Customer Care at 1-800-334-7858. Listen for additional applicable prompts. Hours of operation
are listed below.
During this call:
You will be asked for your name, dealership name, and all of the information collected.
The agent will unregister the original TCU and register the replacement TCU. If needed, the agent will call back to confirm TCU registration has completed.
The vehicle may need to be moved outside if the cellular connection is not strong enough. See Check
TCU Cellular Reception on page 18.
NOTE:
The TCU will not be able to communicate with the Infiniti Data Center if step 46 is not completed.
After registration, it may take up to 48 hours for services to be functional.
TCU registration does not enroll the customer in Infiniti Connection® or Infiniti InTouch Services™.
Infiniti Customer Care (1-800-334-7858) – Hours of Operation (Central Time Zone)
Monday – Friday: 7AM – 10PM Saturday: 8AM – 5PM
Special Holiday Hours: Closed Thanksgiving, Christmas, and New Year’s Day Christmas Eve: 7AM – 7PM New Year’s Eve: 7AM – 7PM
18/25 ITB12-011n
Check TCU Cellular Reception 47. Select Diagnosis (One System) and then TELEMATICS.
48. Select Data Monitor and then Cellular level.
49. Select START.
Figure 24
50. Check the Cellular level and confirm that it is “GOOD”. 51. If the Cellular level is MARGINAL or LOW, move the vehicle to an area with a good signal.
NOTE: The Cellular level constantly updates. Safely relocate the vehicle until a “GOOD” Cellular level is received.
Figure 25
19/25 ITB12-011n
52. Press the NAVI or DEST button.
Figure 26 Figure 27
EXAMPLE
Figure 28 EXAMPLE
Figure 29
53. Select Infiniti Connection, Infiniti InTouch Services,
or Destination Menu.
NOTE: If none of the above options are displayed, proceed to step 54.
54. Select Connected Search.
20/25 ITB12-011n
55. Enter a POI (Point of Interest) location, and select “OK” or “Search”.
Example: “Starbucks” EXAMPLE
Figure 30
56. Confirm the POI location displays.
EXAMPLE
Figure 31
57. If the “Connected Search” does not complete successfully:
If TCU registration with SXM has just been performed, please allow up to 48 hours and try again.
For an unsold vehicle, call Infiniti Customer Care at 1-800-334-7858.
If the vehicle has been sold, the customer will need to be enrolled in Infiniti Connection® or Infiniti InTouch Services™ for the SOS light to be illuminated and for Infiniti Connection® or Infiniti InTouch Services™ to be enabled. Refer to SOS Light Diagnosis Information on page 23.
58. Turn the ignition OFF.
21/25 ITB12-011n
CHECK OFF SHEET IMPORTANT:
If all of the steps below are not completed, telematics services will not operate properly.
Follow all of the steps in this bulletin and use the Check OFF Sheet provided below.
If the TCU is replaced and the steps were not followed, the warranty claim will be charged back to the dealer.
Please staple the completed Check OFF Sheet to repair order.
Perform the following if TCU the has been replaced:
Complete the Applied Vehicle-specific Action in the order listed.
Check OFF the Action as performed.
CHECK
BOX APPLIED VEHICLES ACTION
1 All Vehicles Write VIN to TCU
(1)
2
2016-2018 Q50 * 2016-2018 Q50 Hybrid *
2018-2019 Q70 2018 Q70 Hybrid 2017-2018 Q60
2017-2019 QX30 2019 QX50
2018-2019 QX80
Configure TCU (2)
3
2016-2019 Q50 2016-2018 Q50 Hybrid
2017-2019 Q60 2019 QX50
2017-2019 QX60 2017-2018 QX60 Hybrid
2018-2019 QX80
Register Intelligent Key (3)
4 All Vehicles Turn ON TCU (4)
5 All Vehicles Register TCU with SXM
(5) (1) Refer to page 8, step 15, Section Write VIN to TCU (2) Refer to page 9, section Configure TCU (3) Refer to page 13, step 32, Section Intelligent Key Registration (4) Refer to page 14, section Turn ON TCU (5) Refer to page 17, section TCU Registration * Model year 2018 vehicles with TCU ID that begins with "2047"
22/25 ITB12-011n
Manually Enter VIN Data (if needed) This is needed ONLY if automatic “SAVE VIN DATA” or “WRITE VIN (SAVED DATA)” did not complete correctly.
Figure 1a
Figure 2a
Figure 3a
Step 1 Step
2
1. Select WRITE VIN (MANUAL INPUT). 2. Select Start.
3. Enter the VIN.
a) Touch the VIN (1ST TIME) input field and type in the VIN.
b) Touch the VIN (2ND TIME) input field and type in the VIN again.
4. Select Start.
5. Select End. Return to step 20 on page 9. Step
5
Step 4
Step 3
23/25 ITB12-011n
SOS Light Diagnosis Information (if needed) NOTE: Dealer Demo Mode will expire after 2 months from the vehicle build date. All services will be disabled, including the SOS light. Do NOT replace the TCU. Perform the steps below if the SOS light is not illuminated.
Figure 4a
2. Go to https://owners.infinitinusa.com/iowners/vinlookup/dealervinlookup.
3. Enter the VIN.
Vehicle is shown as not enrolled:
The customer is not enrolled in Infiniti Connection® or Infiniti InTouch Services™. Have the customer enroll and then confirm the SOS light illuminates.
NOTE: It may take up to 48 hours for the services to be activated and the SOS light to illuminate after enrollment is completed.
“VIN not found” displays:
The vehicle needs to be registered in the Infiniti Owner Portal and enrolled in Infiniti Connection® or Infiniti InTouch Services™. Have the customer register and enroll; and then confirm the SOS light illuminates.
NOTE: It may take up to 48 hours for the services to be activated and the SOS light to illuminate after enrollment is completed.
Vehicle is shown as enrolled:
Confirm the customer’s Infiniti Connection® or Infiniti InTouch Services™ subscription.
The customer can find this information three ways:
Log into to the Infiniti InTouch Services™ portal and locate "Manage Subscription" on the first page.
Log into the Infiniti InTouch Services™ mobile app and go to "Vehicle Information" > "Package Info".
Call Infiniti Customer Care at 1-800-334-7858.
If the customer is enrolled in the Premium or Premium Plus Package, call TECH LINE for diagnosis.
If the customer is enrolled in the Select Package, the SOS light is not intended to illuminate. No further action is needed.
1. With the vehicle in an area of known good cellular reception, use C-III plus to confirm the TCU is turned ON.
Light not illuminated
24/25 ITB12-011n
Turning ON the TCU During PDI NOTE:
This procedure is for 2013-2017 Applied Vehicles ONLY.
In most instances, the TCU is ON when delivered to the dealership. See the steps below to determine if the TCU is ON or OFF.
Figure 5a
2. After the TCU is turned ON, check whether or not the green light on the SOS button is illuminated.
If the green light is still not illuminated, verify the vehicle is unsold.
If the vehicle has been sold, the customer will need to be enrolled in Infiniti Connection® or Infiniti InTouch Services™ for the SOS light to be illuminated and for Infiniti Connection® or Infiniti InTouch Services™ to be enabled.
Refer to SOS Light Diagnosis Information on page 23.
3. Perform steps to Check TCU Cellular Reception - see page 18. 4 Turn the ignition OFF. 5. Pull OUT the extended storage switch to return the vehicle to shipping mode.
NOTE: If the “Turning ON the TCU During PDI” procedure is not followed correctly, the vehicle cannot be used in Dealer Demo mode or enrolled in Infiniti Connection® or Infiniti InTouch Services™. Should this occur, the “Turning ON the TCU During PDI” procedure will need to be performed again.
1. With the vehicle in an area of known good reception, turn the ignition ON and check whether or not the green light on the SOS button is illuminated (see Figure 5a).
NOTE: It may be difficult to tell if the green light is illuminated if the vehicle is outside in bright sunlight.
If the green light is illuminated, the process to turn ON the TCU is
complete and no further action is needed.
If the green light is not illuminated, go to Turn ON TCU on page 14.
Light not illuminated
25/25 ITB12-011n
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE DESCRIPTION
March 12, 2012 ITB12-011 Original bulletin published.
May 30, 2012 ITB12-011a Steps 7 and 8 revised.
September 4, 2012 ITB12-011b APPLIED VEHICLES section revised.
September 23, 2013 ITB12-011c APPLIED VEHICLES section revised.
January 5, 2015 ITB12-011d APPLIED VEHICLES section revised, and a statement added to page 1.
May 11, 2016 ITB12-011e Changes made throughout.
August 19, 2016 ITB12-011f Information for 2017 QX30 vehicles added.
October 20, 2016 ITB12-011g Information for 2017 Q50, Q60, Q70, QX60, and QX80 vehicles added.
September 28, 2017 ITB12-011h Information for several 2018 vehicles added.
November 14, 2017 ITB12-011i Changes made throughout.
January 4, 2018 ITB12-011j Changes made to page 15.
March 7, 2018 ITB12-011k Changes made throughout.
September 11, 2018 ITB12-011l Required Actions by Model and Year table added to page 2, Check OFF Sheet added to page 21, and information reorganized throughout.
January 24, 2019 ITB12-011m Information for several 2019 vehicles added.
June 24, 2019 ITB12-011n Added information to pages 2, 9, 11 and 21 for 2017-2018 Q60 TCU configuration.