InnoSys Park Brake ToolMaster Control Panel Screens

Revision A, 12Dec2007

12/12/2007 1

MCP ScreensContents

• 3 MCP Screen Overview• 4 - 5 Main Control Screen• 6 Mode Select Screen• 7 – 9 Verification/Calibration Screens and

Procedures.• 10 - 11 Manual Calibration Procedure and Screen• 11 - 13 Parameter Screens and Settings• 14 - 15 Alarm Screen and Settings• 16 - 19 Alarm Status/History and Alarm Codes and Descriptions• 20 - 21 Log Screens• 22 - 23 Manual Screen• 24 Preventative Maintenance Screen

12/12/2007 2

Master Control Panel Screens

Main Screen

Log Screen 1

Log Screen 2

Alarm Code Screen

Manual Screen Verification/Cal Screen

Parameter Screen Alarm Status

Alarm History

Mode Select Screen

Alarm Setup Screen

12/12/2007

3

Manual verification/cal screen

PM Screen

Lamp Test Screen

Main Control Screen

12/12/2007 4Parameter Screen button accessible after login

Main Control Screen• The Main Screen will always be displayed on the MCP while the tool

is running a normal tension cycle in Auto Mode. This screen indicates when the tool is in cycle, the detailed job status and the outcome of the job such as pass or fail.

• This screen contains a reverse jog button that when held down, will enable the team leader to run the nut back off the job without having to switch to manual mode.

• It is the main screen from which other screens can be selected to run other modes.

• This screen contains a fault reset button that will turn off audible alarms and reset the system for the next job following a fault.

• With the appropriate login this screen is used to access the Parameter Set Up and Alarm Set Up screens.

12/12/2007 5

Mode Select Screen• This screen is accessed through

the Main Screen. • Auto Mode must be selected to

run a normal tension cycle.• Calibrate Mode must be selected

before accessing the Calibration Screen and running a calibration cycle.

• Verification Mode must be selected before accessing the Calibration Screen to run a verification cycle.

12/12/2007 6

Auto Verification/Calibration Screen

12/12/2007 7

Verification Procedure

1. From the Main Screen select Mode Select. In the Mode Select screen select “Verification Mode”.

2. In the Verification/Calibration Screen and with no load applied to either the tool or the cal stand, press the “Zero Offset Button”. Wait 5 seconds for the system to establish the zero offset before installing the tool onto the stand. When zero offset is complete both tool and cal stand load cell with zero offset should show vales near zero.

3. Install the tool onto the cal stand and load the nut into the tool using the extended handle on the stand to cock the tool.

4. To begin the verification cycle press the start button on the tool handle.5. When the cycle is complete the screen will indicate either verification

passed or failed.6. If cycle passes, return to Mode Select Screen, select Auto Mode and place

the tool back into service for normal operation.

12/12/2007 8

Auto Calibration Procedure

1. From the Main Screen select Mode Select. In the Mode Select screen select “Calibration Mode”.

2. In the Verification/Calibration Screen and with no load applied to either the tool or the cal stand, press the “Zero Offset Button”. Wait 5 seconds for the system to establish the zero offset before installing the tool onto the stand. When zero offset is complete both tool and cal stand load cell with zero offset should show vales near zero.

3. Install the tool onto the cal stand and load the nut into the tool using the extended handle on the stand to cock the tool.

4. To begin the calibration cycle press the start button on the tool handle.5. When the cycle is complete the screen will indicate either calibration

passed or failed.6. If cycle passes, return to Mode Select Screen, select Auto Mode and place

the tool back into service for normal operation.

12/12/2007 9

Manual Calibration Screen

12/12/2007 10

Manual Calibration Procedure• Manual Calibration Sequence• From main screen on panel view press “Mode Select” button• Select “Manual” for tool you are calibrating• Press “Close Window” Button• Press “Manual Screen” Button• From Manual screen select “Manual Calibration”• Before connecting tool to calibration stand, press “Set Zero Offset” button.• Install new nut onto threaded rod on calibration stand.• Connect tool to the calibration stand.• Cock tool.• While watching the force on the cal stand scale, press and hold “Start” button on the articulating arm until

the force on the scale is above 250 lbs.• Read the force on the scale.• Press the “Force” button on the panel view and enter the force measured on the scale.• Press the “Calibrate” button• Press the “Reverse Jog” button to remove the nut from the rod.• Pull release ring to remove tool from calibration stand.

12/12/2007 11

Parameter Screen

12/12/2007 12

Alarm Setup Screen Button

Setting Tension Parameters• The Parameters Screen is accessed from the Main screen after pressing the login button and correctly entering the correct

user ID and password.• All tension parameters are set from this screen.

– Target Tension. The stable high tension level achieved before running reverse revolutions .– Overshoot Delta. How many lbs above target tension to achieve during the final slow run up.– Restart Delta. How many lbs tension can drop below target before restarting the slow run up.– Accept Delta. The +/- allowable variation compared to the Target Tension at end of cycle to pass or fail the job.– Cycle Time Limit. Maximum time tool is allowed to run forward before running reverse revolutions.– Min. Run Time on Restart. Tool must run this minimum time at slow run on restart when attempting to achieve final

tension.– Pre Tension Force Target. The percentage of target tension the tool will run at fast speed before going to slow run

speed.– Stable Tension Time. How many seconds tension must be stable and not drop below the restart delta before tool

restarts slow run up.– Reverse Revolutions. How many reverse revolutions the tool must run to release the brakes after target tension is

achieved.– Slow and Fast Run Speeds. Selected applications from the Cooper Controller.

• The verification acceptance delta is set from this screen. This is the allowable variation between the tool load cell reading and the verification stand load cell reading after running the verification cycle.

• The Alarm Setup Screen is accessed from this screen.

12/12/2007 13

Alarm Setup Screen

12/12/2007 14

Setting AlarmsAlarm Set Ups:

– Misload Alarm Set-Up. These alarms are separate from the tool misload alarms triggered by the prox switch. These alarms are set to detect faults when a specific minimum level of tension is not achieved within a specified period of time after cycle start. They are set for Auto, Calibration and Verification modes.

– Cal zero offset limit. This alarm is set when the tool load cell and cal stand load cell differ by more than this specified amount after running the zero offset routine.

– Cal Cycle Start Tension Limit. The cal cycle will not start if the amount of tension on the cal stand exceeds this value. This would typically occur if the cal stand nut is already run up a certain amount before attempting to run the cal or verification cycle.

– Cal Jog Forward Timeout. The maximum amount of time the tool is allowed to run forward during the cal or verification cycle.

– Tool removed During Fast Run. This alarm is set to detect a significant drop in tension after a certain level of tension is achieved and is set above that level established in the Misload Alarm above.

12/12/2007 15

Alarm Status Screen

• The Alarm Status Screen is displayed on the HMI when a fault occurs in any mode. It shows a description of the fault along with the fault code.

12/12/2007 16

Alarm History Screen

• The Alarm History Screen displays the date and time of each fault that has occurred along with the fault code and description of each fault.

12/12/2007 17

Alarm Code Screen

12/12/2007 18

Alarm Code Descriptions

• The Alarm Code Screen is accessed through the Log Screens.

• This screen lists all of the Alarm codes and faults that can occur in auto, verification or calibration mode with the description of each alarm code.

12/12/2007 19

Log Screens

12/12/2007 20

Log Screens

• Accessed from the Main Screen• The Log Screens are used to review detailed

job history according to date and time, tool number and alarm codes if they occur.

• The Log Screen has a “Codes” button allowing the user to access the alarm code screen.

12/12/2007 21

Manual Screen

12/12/2007 22

Manual Screen

• The Manual Screen is accessed from the Main Screen. After placing the system into Manual Mode, this screen can be used to test the operation of the nut runner and end effecter by using the panel buttons to jog the tool forward or reverse.

12/12/2007 23

Preventative Maintenance Alert Screen

• The PM screen is displayed when PM is due on selected items. These items are primarily associated with replacement or repair of mechanical components in the end effecter and crows foot.

12/12/2007 24