innovators in protection technlogy tembreak plus · during a fault condition, a circuit breaker...

TemBreak Plus For High Demand Applications

Ics=Icu=50kA & 85kA, Selectivity with 3:1 MCCB ratio

owerful interrupting Capacities

imitation of System Damage

nique Contact Structure

P

LU

electivity Enhanced Switchgear S

Innovators in Protection Technlogy

2

TemBreak PlusHigh Demand Applications

TemBreak Plus

TemBreak Plus meets this need, with frame sizes and accessories whichare completely compatible with the well established TemBreak range.Together TemBreak and TemBreak Plus offer a massive choice of ratings -one for every application!

Contact your local office for sales, service and application support.(Addresses on rear cover).

Marine systems with high demand loads and short cable runs, high faultservice rated switchboards, fully selective secure supplies.....

.....highly rated electrical installations need highly rated MCCB protection.

Innovators in Protection Technology

Innovators in Protection Technology

3

Section Contents Page

Product Features 5-10

Ratings and Specifications 11-16

Outline Dimensions 33-42

Optional Accessories 25-32

Thermal Magnetic Characteristics 17-20

Microprocessor Based Characteristics 21-24

N S

IEC

7 8 94 5 6

1 2 30 . X

=

–

+

ON

OFF

Selectivity Table 43-44

5

Product Features

Section

ON

OFF

6

Type XH125PJ XH160PJ XH250PJ XH400PJ XH400PE XH630PJ XH630PE XH800PJ XH800PE

No. of poles 3,4 3,4 3,4 3,4 3,4 3,4 3,4 3,4 3,4

Ampere Frame 125 160 250 400 400 630 630 800 800

Rated Current In (Amp) 20,32,50,63 160 160,250 250,400 250,400 400,630 630 800 800

100,125

Rated AC breaking

capacity 690V 8/4 15/7.5 18/9 18/9 20/10 45/23 20/10 45/23 20/10IEC 60947-2 500V 25/13 25/13 42/21 42/21 42/21 65/33 42/21 65/33 42/21Icu/Ics kA 440V 42/35 42/35 65/50 65/50 65/50 85/43 65/50 85/43 65/50 415V 50/50 50/50 65/50 65/50 65/50 85/50 65/50 85/50 65/50 400V 50/50 50/50 65/50 65/50 65/50 100/50 65/50 100/50 65/50

Type TL-100NJ TL-250NJ TL-400NE TL-630NE TL-800NE TL-1250NE

No. of poles 3,4 3,4 3,4 3,4 3,4 3,4

Ampere Frame 100 250 400 630 800 1250

Rated Current In (Amp) 20,32,50, 160,250 400 630 800 1000

63,100 1250

Rated AC breaking

capacity 690V - - 25/25 25/25 45/34 45/34 45/34

IEC 60947-2 500V - - 70/70 70/70 75/57 75/57 75/57

Icu/Ics kA 440V 85/85 85/85 85/85 125/70 125/70 125/65

415V 85/85 85/85 85/85 125/70 125/70 125/65

400V 85/85 100/100 100/100 125/70 125/70 125/65

Type XS400SE XH400SE XS630SE XH630SE XS800SE XH800SE XS1250SE XH1250SE

No. of poles 3,4 3,4 3,4 3,4 3,4 3,4 3,4 3,4

Ampere Frame 400 400 630 630 800 800 1250 1600

Rated Current In (Amp) 250,400 250,400 630 630 800 800 1000 1600

1250

Rated AC breaking

capacity 690V 18/9 20/10 20/10 20/10 20/10 20/10 25/19 45/34

IEC 60947-2 500V 30/15 42/21 35/18 42/21 35/18 42/21 45/34 65/49

Icu/Ics kA 440V 42/21 65/33 50/25 65/33 50/25 65/33 65/49 85/64

415V 50/25 65/33 50/25 65/33 50/25 65/33 65/49 65/49

400V 50/25 65/33 50/25 65/33 50/25 65/33 85/64 100/75

PowerBreaker Series Ics = 50kA

LimitorBreaker Series Ics = 65~85kA

Selectivity Series 3:1 Selectivity

Product Features

TemBreak Plus

High Demand Applications

Thermal magnetic • • • • • •

Microprocessor • • •

Dimensions 4P 120x155x86 140x165x103 185x260x103 185x260x103 185x260x103 280x273x103 280x273x103 280x273x103 280x273x103

Dimensions 3P 90x155x86 105x165x103 140x260x103 140x260x103 140x260x103 210x273x103 210x273x103 210x273x103 210x273x103

Reference MCCB

for accessories XH125NJ XH250NJ XS400NJ XS400NJ XH400NE XS630NJ XH630NE XS800NJ XH800NE

Thermal magnetic • •

Microprocessor • • • •

Dimensions 4P 120x235x86 185x360X103 185x360x103 280X370X140 280X370X140 280x370x140

Dimensions 3P 90x235x86 140x360x103 140x360x103 210x370x140 210x370x140 210x370x140

Reference MCCB

for accessories XH125NJ XH400NJ XS400NE XS1600NE XS1600NE XS1600NE

Microprocessor • • • • • • • •

Dimensions 4P 185x260x103 185x260x103 280x273x103 280x273x103 280x273x103 280x370x120 280x370x120 280x370x140

Dimensions 3P 140x260x103 140x260x103 210x273x103 210x273x103 210x273x103 210x273x103 210x370x120 210x370x140

Reference MCCB

for accessories XS400NE XH400NE XS630NE XH630NE XS800NE XH800NE XS1250NE XS1600NE

7

Icu=o-co 2 Full Short CircuitsIcs=o-co-co 3 Full Short Circuits

During a fault condition, a circuit breaker withexcellent current limiting ability such as TemBreakPlus, can substantially reduce damage to the electricalsystem and thus minimise downtime.This current limiting feature reduces the peak letthrough current (Ipeak) and energy let through (I2t)during fault conditions.

Terasaki's TemBreak Plus MCCBs achieve thisexceptional current limiting performance by utilising aunique contact structure which we call the Fast BreakMechanism (FBM).The U-Shaped contact of this mechanism assists in theelectromagnetic repulsion of the contact tips for fastarc extinction.The 50kA PowerBreaker Series uses oneFBM per pole whilst the LimitorBreaker Series usestwo FBM per pole to achieve its rating of 85kA.

The need for a continuous and reliable power supplyplaces increased emphasis on selectivity requirementsin today's electrical distribution system.The Selectivity Series utilises microprocessor basedprotection, giving enhanced selectivity. This ensures3:1 ratio between the upstream and downstreamMCCBs. For further details please refer to theselectivity table on page 31 of this catalogue.

Powerful Interrupting Capacities Limitation of System Damage

Unique Contact Structure Selectivity Enhanced Switchgear

Icu = 50kAIcs = 25kA

XH125NJ

Icu = 50kAIcs = 50kA

XH125PJ Ics = 85kAIcu = 85kATL100NJ

Plus

Plus

kA

Conventional MCCB

TemBreak Plus

50

9

I peak

t

I t2

I t2

2

4

6

8

10

I2I1

0.1

0.2 0.3

0.4

IG

5

10

15

20

30

T1

0.1

0.150.2

0.25

0.3

SECT2

0.1

0.2

0.3

0.4

0.8

SECTG

LONG TIME SHORT TIME INSTANTANEOUS GROUND FAULT

TIMESETTING

PICK UP

SHORT TIME I2t

OFF ONTEST IN

SECat 6 x I1

RATED CUR. (A)

T

I

IG

I1

T1

I2 T2

I3TG

BASE CUR.

AIC

x In

0.63 0.8 1.0

0.8

0.85

0.9

0.95

1.0

CURR.SETTING

xI0 x I0X In

T2 SECat 10 x I0

12501250

3

6 9

12

x I0I3

CT RATED CURRENT

In A

The majority of distribution systems are designed to anultimate short circuit rating (Icu). An Icu rated MCCBprovides the optimum protection in terms of safe andeconomical selection.Certain applications may require protection which isdesigned to the more onerous service short circuitrating (Ics).Terasaki's TemBreak Plus range can provide a widechoice of MCCBs with superior Ics ratings up to 85kAat 440V AC.

Product Features

TemBreak Plus


8

Product Features

TemBreak Plus


Very often, MCCBs must grade with other protective devices that may not have adjustable characteristics.This could be either a downstream fuse or an upstream electricty authority relay. Each microprocessorbased TemBreak Plus can achieve as standard over 200,000 independant time current characteristics. Thisunique curve flexibility enables TemBreak Plus to achieve full selectivity even in the tightest of gradingsystems.

Microprocessor Time Current Characteristics

Microprocessor Adjustment Facia

4

3

2

15040

30

20

108

654

3

2

1504030

20

108

654

3

2

10.8

0.60.50.4

0.3

0.2

0.10.080.060.050.04

0.03

0.02

0.010.008

0.0060.005

8 9 10 15 20 25 30 40 50 60 70 80 90 100 60 70 80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

0.7

0.8

1.0

IP x I1

0.9

Pre-trip alarm(PTA) characteristics

Long time-delay (LTD) tripcharacteristic

Short time-delay (STD) tripcharacteristic

Instantaneous (INST)trip characteristic

Short time-delayI2t ramp selector switch

Ground fault trip(GFT) Characteristics

0.1

0.2 0.3

0.4

IG X In

0.1

0.2

0.3

0.4

0.8

SECTG

5

10

15

20

30

T1 SECat 6 x I1

I1

0.8

0.85

0.9

0.95

1.0

xI0

2

4

6

8

10

I2

0.1

0.150.2

0.25

0.3

SECT2x I0

OFF ON

T2 SECat 10 x I0

3

6 9

12

x I0I3

Tri

pp

ing

tim

e

Percent x[In] Percent x[Io]

ho

ur

min

ute

seco

nd

2

4

6

8

10

I2I1

0.1

0.2 0.3

0.4

IG

5

10

15

20

30

T1

0.1

0.150.2

0.25

0.3

SECT2

0.1

0.2

0.3

0.4

0.8

SECTG

LONG TIME SHORT TIME INSTANTANEOUS GROUND FAULT

TIMESETTING

PICK UP

SHORT TIME I2t

OFF ONTEST IN

Example XS1250SE

SECat 6 x I1

RATED CUR. (A)

T

I

IG

I1

T1

I2 T2

I3TG

PRE TRIP ALARM

0.7

0.8

1.0

IP x I1

0.9

BASE CUR.

AIC

x In

0.63 0.8 1.0

0.8

0.85

0.9

0.95

1.0

CURR.SETTING

xI0 x I0X In

T2 SECat 10 x I0

12501250

3

6 9

12

x I0I3

CT RATED CURRENT

In A

TRIP INDICATORSRESET

9

Product Features

TemBreak Plus


Flexibility

In addition to TemBreak microprocessor MCCBsbeing the most flexible on the market, a number ofimportant features are available as STANDARD!Most other MCCB manufacturers offer theserelevant features at a premium price.

Provision of adjustable LTD T1 settings and STDT2 setting are important to match the protec-tive characteristic to the load requirement. Itis also extremely useful to provide flexible grad-ing with other devices.

When co-ordinating between MCCB and fuses,it can often be difficult to obtain the requiredselectivity due to the different shape of the timecurrent curves. With a flick of a switch the I2tramp can be enabled to make grading easier.

Inductive loads such as motors often producea transient inrush on initial switching. In thisapplication it is important to have anadjustable instantaneous trip to set above thisinrush current.

T1

T2

5 sec

30 sec

300 msec

100 msec

L.V.fusedownstream

I3

motorstartingcurve

300% 1200%

Adjustable Time Settings

Adjustable Inst. TripAdjustable I T Ramp2

10

Electronic office equipment is being increasingly usedin today's buildings and factories.The power demand at peak time can reach overloadlevels of the breakers installed in the system. If such asituation continued a sudden trip may be generatedby the long time-delay trip function of the breaker.The pre-trip alarm prevents this 'sudden trip' by trippingout non-essential loads thus ensuring an uninterruptedsupply to essential loads.

TemBreak Plus MCCBs from 125AF to 1600AF aresuitable for isolation as defined by IEC 947-2. PositiveContact Indication (PCI) is achieved via the togglemechanism.Padlocks can only be installed if the contacts are fullyopen.

As well as microprocessor MCCBs from 125A to 1600A,Terasaki is one of the few manufacturers who can stilloffer a complete range of Thermal Magnetic MCCBsup to 800AF. The thermal adjustment of the TemBreakPlus range, 63% to 100% of the nominal rating, is oneof the biggest on the market.This proven form of electromechanical technology stillrepresents by far the largest type of MCCBs sold onthe European Market.Wouldn't you prefer the choice?

Output contact (1a)of the pre-trip alarm

SHTSHT

Essential Load Non-essential Load Non-essential Load

TemBreak

Computer

400A

ONI

400A 400A

OFFO

Pre-Trip Alarm Function (Optional)

Suitable for Isolation Choice of Protection

Thermal Adjustment63% - 100% x In

Magnetic Adjustment500% - 1000% x In

Ir 0.8

0.63 1

xIn

Im

6

5

7.18.5

10

xIn

I (ON) TRIP O (OFF)

High Frequency Harmonics Detected

TemBreak MCCBs employ a True R.M.S. detectionthrough a process of sampling and integrating.Even those MCCBs that claim True R.M.S. may only doso up until the 3rd or 5th Harmonic. Ignoring higherfrequency harmonics can lead to 'under protection'of the conductor. By utilizing a high sampling rate of500 µsec TemBreak microprocessor MCCBs detect upuntil and including the 19th Harmonic.

Frequency spectrum

Conventional r.m.s.

detection can ignore

higher frequency

harmonics

%

3

50

5 7 9 11 13 15 17 19

Total

Harmonic

Distortion

Product Features

TemBreak Plus


11

Ratings and

Section

IEC

7 8 94 5 6

1 2 30 . X

=

–

+

Specifications

12

3

5

5

44 4 4 4

Notes:

•

• 5

4

3

2

1NRC : Nominal Rated Current : The application on IT systems on this voltage is not available.ASR : Adjustable Setting Range : Available on request, contact Terasaki for details.

: Standard. This configuration is used unless otherwise specified. : For AC UVT, a UVT controller is mounted externally : Optional. Specify when ordering. : Line side interpole bariers supplied as standard. : Yes or available. : Draw out leads horizontally.

– : No or not available.

Ampere FrameType

2 2 2

Number of polesRATED CURRENT (A). [In]Calibrated at 45°C

RATED IMPULSE WITHSTAND VOLTAGE Uimp [kV]AC RATED INSULATION VOLTAGE [Ui]AC RATED BREAKING CAPACITY sym. r.m.s. [kA]IEC 947-2 [Icu] IEC 947-2 [Ics]BS EN 60947-2 [Icu] BS EN 60947-2 [Ics]CEI EN 60947-2 [Icu] CEI EN 60947-2 [Ics]

Without Inst.DC RATED BREAKINGCAPACITY [kA]RATED SHORT TIME CURRENT r.m.s. [kA] [Icw]UTILIZATION CATEGORYOUTLINE DIMENSIONS (mm) w

hd1d2

Weight (kg) marked standard typeCONNECTIONS AND MOUNTINGSFront Terminal screw (FCS)connected (FC) Attached flat bar (BAR)

Solderless terminal (PWC)Rear Bolt stud (REB)connected (RC) Flat bar stud (REF)Plug-in (PM) For switchboard (PRC/PMB)

For distribution boardDraw-out (DO)STANDARD FEATURESON-OFF colour indicationTrip buttonPROTECTIVE FUNCTIONSElectronic type

Adjustable LTD, STD & INST.Adjustable GFT or Adjustable PTA (option)Trip Indicators (option)

Thermal-magnetic typeThermal and fixed magnetic tripsThermal and adjustable magnetic tripsAdjustable thermal and fixed magnetic tripsAdjustable thermal and magnetic trips

ACCESSORIES (option)Internally Auxiliary switchmounted Alarm switch

Shunt trip Undervoltage trip

Externally Motor operatormounted Handle Panel mounted type

operating Breaker mounted type mechanism Variable depth type Handle extension Mechanical Front type interlock Rear type Handle holder Handle lock Terminal Front conn. type cover Rear conn./ plug-in type Interpole barrier Accessory lead terminal

Door flange IP20 Protection (Plug-in type)

125 160 250 400 400XH125PJ XH160PJ XH250PJ XH400PJ XH400PE

Ratings and Specifications

TemBreak Plus

PowerBreaker Series

3 4 3 4 3 4 3 4 3 4NRC ASR NRC ASR NRC ASR NRC ASR NRC ASR min. max. min. max. min. max. min. max. min. max. 20 13 20 160 100 160 160 100 160 250 160 250 400 200 400 32 20 32 250 160 250 400 250 400 50 32 50 63 40 63100 63 100125 80 1258 8 8 8 8690 690 690 690 690

690V 8/4 15/7.5 18/9 18/9 20/10 500V 25/13 25/13 42/21 42/21 42/21 440V 42/35 42/35 65/50 65/50 65/50 415V 50/50 50/50 65/50 65/50 65/50 400V 50/50 50/50 65/50 65/50 65/50 380V 50/50 50/50 65/50 65/50 65/50 240V 85/50 85/50 85/50 85/50 100/50 240-690V – – – – 5 250V 40 40 40 40 – 125V 40 40 40 40 –

– – – – 5 (0.3 sec)A A A A B90 120 105 140 140 185 140 185 140 185155 165 260 260 26086 103 103 103 103104 124 131 145 131 145 131 1451.3 1.6 2.1 2.6 4.7 6.1 4.7 6.1 4.8 6.2

– O (BAR) O (BAR) O (BAR) O (BAR)O O O O OO – – – –– O O O OO O O O –O – – – –– O O O O

• • • • •• • • • •

– – – – •– – – – • (PTA only)– – – – –

– – – – –– – – – – –

• • – – –– – • • –

CODE AX,AXE •(AXE) •(AXE) •(AX) •(AX) •(AX) AL,ALE •(ALE) •(ALE) •(AL) •(AL) •(AL)

SHT • • • • •UVT • • • • •MOT • • • • •OHE • • • • •OHJ • • • • •OHH • • • • •EHA – – – – –MIF • • • • •MIB • • • • •HH • • • • •HL • • • • •TCF • • • • •TCR • • • • •TBA • • • • •LTF • • • • •LTS – – – – –D.F • • • • •IP20 • • • • •

2

1

1

1

1

1

1

1

1

1

1

• • • • •

13

3

5

Notes:

•

• 5

4

3

2


: Standard. This configuration is used unless otherwise specified. : For AC UVT, a UVT controller is mounted externally : Optional. Specify when ordering. : Line side interpole bariers supplied as standard. : Yes or available. : Draw out leads horizontally.


Ampere FrameType

2 2

• • •




hd1d2











630 630 800 800XH630PJ XH630PE XH800PJ XH800PE3 4 3 4 3 4 3 4NRC ASR NRC ASR NRC ASR NRC ASR min. max. min. max. min. max. min. max.400 250 400 630 315 630 800 500 800 800 400 800630 400 630

8 8 8 8690 690 690 690

690V 45/23 20/10 45/23 20/10 500V 65/33 42/21 65/33 42/21 440V 85/43 65/50 85/50 65/50 415V 85/50 65/50 85/50 65/50 400V 100/50 65/50 100/50 65/50 380V 100/50 65/50 100/50 65/50 240V 125/63 100/50 125/63 100/50 240-690V – 10 – 10 250V 40 – 40 – 125V 40 – 40 –

– 10 (0.3 sec) – 10 (0.3 sec)A B A B210 280 210 280 210 280 210 280273 273 273 273103 103 103 103145 145 145 1459.0 11.5 9.0 11.5 9.0 11.5 9.0 11.5

– – – –

O O O O– – – –O O O OO O O O– – – –• • • •

• • • •• • • •

– • – •– • – •– • – •

– – – –– – – – –

– – – –• – • –

CODE AX,AXE •(AX) •(AX) •(AX) •(AX) AL,ALE •(AL) •(AL) •(AL) •(AL)

SHT • • • •UVT • • • •MOT • • • •OHE • • • •OHJ • • • •OHH • • • •EHA • • • •MIF • • • •MIB • • • •HH • • • •HL • • • •TCF • • • •TCR • • • •TBA • • • •LTF • • • •LTS – – – –D.F • • • •IP20 • • • •

2

1

1

1

1

1

1

1

1

•

2

22


TemBreak Plus

PowerBreaker Series

14

3

5

4 4

Notes:

•

• 5

4

3

2


: Standard. This configuration is used unless otherwise specified. : For AC UVT, a UVT controller is mounted externally : Optional. Specify when ordering. : Line and load side interpole bariers supplied as standard. : Yes or available. : Draw out leads horizontally.


Ampere FrameType

• • •

•




hd1d2











TL-100NJ TL-250NJ TL-400NE TL-630NE TL-800NE TL1250NE


TemBreak Plus

LimitorBreaker Series

1

1

1

1

1

1

1

1

1

1

• •

4

2 2

3 4 3 4 3 4 3 4 3 4 3 4NRC ASR NRC ASR NRC ASR NRC ASR NRC ASR NRC ASR min. max. min. max. min. max. min. max. min. max. min. max. 20 12.5 20 160 100 160 250 160 250 630 315 630 800 400 400 1000 500 1000 32 20 32 250 160 250 400 250 400 1250 630 1250 50 32 50 63 40 63100 63 100

8 8 8 8 8 8690 690 690 690 690 690

690V – – 25/25 25/25 45/34 45/34 45/34 500V – – 70/70 70/70 75/57 75/57 75/57 440V 85/85 85/85 85/85 125/70 125/70 125/65 415V 85/85 85/85 85/85 125/70 125/70 125/65 400V 85/85 100/100 100/100 125/70 125/70 125/65 380V 85/85 100/100 100/100 125/70 125/70 125/70 240V 100/100 130/130 130/130 150/113 150/113 150/113 240-690V – – 15 15 15 15 250V 40 40 – – – – 125V 40 40 – – –

– – 15 (0.3 sec) 15 (0.3 sec) 15 (0.3 sec) 15 (0.3 sec)A A B B B B90 120 140 185 140 185 210 280 210 280 210 280235 360 360 370 370 37086 103 103 140 140 140104 145 145 191 191 1912.2 2.7 7.1 9.1 7.1 9.1 25.8 33.5 25.8 33.5 26.0 33.7

– – ––

– –– – – –

–

– – – – – –– – – – – –

• • • • •• • • • •

– – • • • •– – • (PTA only) • • •– – – • • •

– – – – – –– – – – – – –

• – – – – –– • – – – –

CODE AX,AXE •(AXE) •(AX) •(AX) •(AX) •(AX) AL,ALE •(ALE) •(AL) •(AL) •(AL) •(AL)

SHT • • • • •UVT • • • • •MOT • • • • •OHE – – – • •OHJ • • • • •OHH • • • • •EHA – – – • •MIF • • • • •MIB • • • • •HH • • • • •HL • • • • •TCF • • • • •TCR • • • – –TBA • • • • •LTF • • • • •LTS – – – – –D.F • • • • •IP20 • • • • •

100 400 400 1600 1600 1600

15

NRC : Nominal Rated Current : Available on request, contact Terasaki for details.ASR : Adjustable Setting Range : For AC UVT, a UVT controller is mounted externally.

: Standard. This configuration is used unless otherwise specified. : Line side interpole barriers are supplied as standard. : Optional. Specify when ordering. : Draw-out leads, horizontally. : Yes or available.


2

5

•

Notes:

•

•

4

3

2

Ampere FrameType

44

5



Without Inst.DC RATED BREAKINGCAPACITY [kA]RATED SHORT TIME CURRENT r.m.s. [kA] [Icw]UTILIZATION CATEGORYOUTLINE DIMENSIONS (mm)

whd1d2











400 400 400 630 630XS400SE-C XS400SE XH400SE XS630SE-C XS630SE

•

4

2 2 2 2

3 4 3 4 3 4 3 4 3 4NRC ASR NRC ASR NRC ASR NRC ASR NRC ASR min. max. min. max. min. max. min. max. min. max.250 125 250 250 125 250 250 125 250 630 400 630 630 400 630400 250 400 400 250 400 400 200 4008 8 8 8 8690 690 690 690 690

690V 16/8 18/9 20/10 16/8 20/10 500V 22/11 30/15 42/21 25/13 35/18 440V 30/15 42/21 65/33 30/15 50/25 415V 35/18 50/25 65/33 35/18 50/25 400V 35/18 50/25 65/33 40/20 50/25 380V 35/18 50/25 65/33 40/20 50/25 240V 50/25 85/43 100/50 50/25 85/43 240-690V 5 5 5 10 10 250V – – – – – 125V – – – –

5 (0.3 sec) 5 (0.3 sec) 5 (0.3 sec) 10 (0.3 sec) 10 (0.3 sec)B B B B B

140 185 140 185 140 185 210 280 210 280260 260 260 273 273103 145 103 145 103 145 103 103131 131 131 145 1454.8 6.2 4.8 6.2 4.8 6.2 9.6 12 9.6 12

– –O (BAR) O (BAR) O (BAR)O O O O O– – – – –O O O O OO O O O O– – – – –

• • • • •• • • • •

• • • • •• (PTA only) • (PTA only) • (PTA only) • •• • • • •

– – – – –– – – – –– – – – –– – – – –

CODE AX,AXE •(AX) •(AX) •(AX) •(AX) •(AX) AL,ALE •(AL) •(AL) •(AL) •(AL) •(AL)

SHT • • • • •UVT • • • • •MOT • • • • •OHE • • • • •OHJ • • • • •OHH • • • • •EHA • • • • •MIF • • • • •MIB • • • • •HH • • • • •HL • • • • •TCF • • • • •TCR • • • • •TBA • • • • •LTF • • • • •LTS • • • • •D.F • • • • •IP20 • • • • •

2


TemBreak Plus

Selectivity Series

• • •

•

16

•

1

5

3

Notes:

Ampere FrameType



Without Inst.DC RATED BREAKINGCAPACITY [kA]RATED SHORT TIME CURRENT r.m.s. [kA] [Icw]UTILIZATION CATEGORYOUTLINE DIMENSIONS (mm)

whd1d2











•• • ••

2

2

22

222 2

630 800 800 1250 1600XH630SE XS800SE XH800SE XS1250SE XS1600SE


TemBreak Plus

Selectivity Series

3 4 3 4 3 4 3 4 3 4NRC ASR NRC ASR NRC ASR NRC ASR NRC ASR min. max. min. max. min.max. min.max. min.max.630 315 630 800 400 800 800 400 800 1000 500 1000 1600 800 1600

1250 630 12508 8 8 8 8690 690 690 690 690

690V 20/10 20/10 20/10 25/19 45/34 500V 42/21 35/18 42/21 45/34 65/49 440V 65/33 50/25 65/33 65/49 85/64 415V 65/33 50/25 65/33 65/49 85/64 400V 65/33 50/25 65/33 85/64 100/75 380V 65/33 50/25 65/33 85/64 100/75 240V 100/50 85/43 100/50 100/75 125/94 240-690V 10 10 10 15 20 250V – – – – – 125V – – – – –

10 (0.3 sec) 10 (0.3 sec) 10 (0.3 sec) 15 (0.3 sec) 20 (0.3 sec)B B B B B

210 280 210 280 210 280 210 280 210 280273 273 370 370 370103 103 103 120 140145 145 145 171 1919.6 12.0 9.7 12.5 9.7 12.5 22.0 28.0 27.0 35.0

– – – – –

O O O O –– – – – –O O O O OO O O O –– – – – –– – – – –

• • • • •• • • • •

• • • • •• • • • •• • • • •

– – – – –– – – – –– – – – –– – – – –

AX,AXE •(AX) •(AX) •(AX) •(AX) •(AX) AL,ALE •(AL) •(AL) •(AL) •(AL) •(AL)

SHT • • • • •UVT • • • • •MOT • • • • •OHE • • • • •OHJ • • • • •OHH • • • • •EHA • • • • •

MIF • • • • • •MIB • • • • •HH • • • • •HL • • • • •TCF • • • – –TCR • • • – –TBA • • • • •LTF • • • • •LTS – – – – –D.F • • • • •IP20 • • • • –

2NRC : Nominal Rated Current : Available on request, contact Terasaki for details.ASR : Adjustable Setting Range : For AC UVT, a UVT controller is mounted externally.

: Standard. This configuration is used unless otherwise specified. : Draw-out leads, horizontally. : Optional. Specify when ordering. : Yes or available.


3

5

•

•

2

17

Thermal Magnetic

Section

Characteristics

N S

18

Thermal Magnetic Characteristics

Time/Current Curves

XH125PJ, XH160PJ

Time/current characteristic curvesXH160PJ

Time/current characteristic curvesXH125PJ

Percent Rated Current

Trip

pin

g T

ime

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80

90

10

0

12

5

15

0

20

0

25

0

30

0

40

0

50

0

60

0

70

08

00

90

01

00

0

15

00

20

00

25

00

30

00

40

00

50

00

60

00

70

00

80

00

seco

nd

min

ute

ho

ur

125A

20, 32, 50, 63, 100A

Max.

Min.

Ambient compensating curvesAmbient compensating curves

130

120

110

100

900 10 20 30 40 50 60

Calibratedtemperature

5 15 25 35 45 55 6510 20 30 40 50 60 70

Calibrated at 40°C45°C50°C

Ambient temperature (°C)

Per

cent

cur

rent

rat

ing

160A(min.)

160A(max.)


Trip

pin

g T

ime

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80

90

10

0

12

5

15

0

20

0

25

0

30

0

40

0

50

0

60

0

70

08

00

90

01

00

0

15

00

20

00

25

00

30

00

40

00

50

00

60

00

70

00

80

00

seco

nd

min

ute

ho

ur

Max.

Min.

Magnetic trip current

Rated curr.(A) Mag. trip curr.NRC (A)20 260±5232 420±8450 650±13063 820±164

100 1300±260 125 1550±310


Rated curr.(A) Mag. trip curr.NRC (A)160 1760±176

150

140

130

120

110

100

90

800 10 20 30 40 50 60


50A, 20A(min.)

50, 20A(max.)

5 15 25 35 45 55 65Calibrated at 40°C

45°C 50°C


Per

cent

cur

rent

rat

ing

100, 32A(max.)

63A(min.)

100, 32A(min.)

125A(min.)

125A(max.)63A(max.)

10 20 30 40 50 60 70

19


Time/Current Curves

XH250PJ, XH400PJ, XH630PJ, XH800PJ

Time/current characteristic curvesXH630PJ, XH800PJ

Time/current characteristic curvesXH250PJ, XH400PJ


Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

ndm

inut

eho

ur

Min.

Max.

X5 X10


Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

ndm

inut

eho

ur

Min.

Max.

X5 X10


130

120

110

100

900 10 20 30 40 50 60


800A (min)630A (min)400A (min)



Per

cent

cur

rent

rat

ing

5 15 25 35 45 55 6510 20 30 40 50 60 70

800A (max)630A (max)400A (max)


Rated curr.(A) Mag. trip curr.NRC (A)160 1660±160250 2500±250400 4000±400


Rated curr.(A) Mag. trip curr.NRC (A)400 4000±160630 6300±250800 8000±400

130

120

110

100

90 0 10 20 30 40 50 60 5 15 25 35 45 55 6510 20 30 40 50 60 70


250A max.400A max.



Per

cent

cur

rent

rat

ing

250A min.400A min.

20


Time/Current Curves

TL-100NJ, TL-250NJ

Time/current characteristic curvesTL-250NJ

Time/current characteristic curvesTL-100NJ



Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

ndm

inut

eho

ur


Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

ndm

inut

eho

ur

x5 x10

80

90

100

110

120

130

140

150

160

10 20 30 40 505 15 25 35 45 55

Calibrated at 40 C45 C

Ambient temperature ( C)

Per

cent

cur

rent

rat

ing

0


o

o

32.50A min

100A min

63A min

20A min

100A max

32.50A max

20A max

63A max

90

100

110

120

130

140

150

10 20 30 40 505 15 25 35 45 5510 20 35 40 50 60

Calibrated at 40 C45 C50 C

Ambient temperature ( C)

Per

cent

cur

rent

rat

ing

0


250A min

160A max

250A max

160A min

o

o

o


Rated curr.(A) Mag. trip curr.NRC (A)20 260±5232 420±8450 650±13063 820±164

100 1300±260


Rated curr.(A) Mag. trip curr.NRC (A)160 1600±160250 2500±250

21

Section

Microprocessor BasedCharacteristics

Overcurrent tripping characteristics Overcurrent tripping characteristics

Time/current characteristic curvesXS630SE, XS630SE-C, XH630SE, XH630PE,XS800SE, XH800SE, XH800PE

Time/current characteristic curvesXS400SE, XS400SE-C, XH400SE, XH400PE,

CT rated current (A) (In) 250,400Base current setting (A): (Io) (In) x (0.63-0.8-1.0)Long time-delay pick-up current (A): (I1) (Io) x (0.8-0.85-0.9-0.95-1.0) Non-tripping at (I1)

setting x 105% and below. Tripping at 125% and above.Long time-delay time settings (S) (T1) (5–10–15–20–30) at (I1) x 600% current.

Setting tolerance ± 20%Short time-delay pick-up current (A): (I2) (Io) x (2-4-6-8-10) Setting tolerance ± 15%Short time-delay time settings (S) (T2) Opening time (0.1, 0.15, 0.2, 0.25, 0.3) in the definite

time-delay. Total clearing time is + 50 mS andresettable time -20mS for the time-delay setting

Instantaneous trip pick-up current (A) (I3) Continuously adjustable from (Io) x (3 to12)Setting tolerance ± 20%

* Pre-trip alarm pick-up current (A) (IP) (I1) x (0.7, 0.8, 0.9, 1.0) Setting tolerance ±10%* Pre-trip alarm time setting (S) (TP) 40 fixed definite time-delay.Setting tolerance ±10%Note: * OptionalNote: The underlined values will be applied as standard ratings unless otherwise specified when ordering.

Percent rated current of base current (I0)

Trippin

g T

ime

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80

90

10

0

12

5

15

0

20

0

25

0

30

0

40

0

50

0

60

0

70

08

00

90

01

00

0

15

00

20

00

25

00

30

00

seco

nd

min

ute

ho

ur

8 9

10

12

.5 15

20

40

50

Percent rated current ofCT rated current (In)

Microprocessor Based Characteristics

Time/Current Curves

PowerBreaker and Selectivity Series

T

I

IG

I1

T1

I2 T2

I3TG

IP

CT rated current (A) (In) 630,800Base current setting (A): (Io) (In) x (0.63-0.8-1.0)Long time-delay pick-up current (A): (I1) (Io) x (0.8-0.85-0.9-0.95-1.0) Non-tripping at (I1)

setting x 105% and below. Tripping at 125% & above.Long time-delay time settings (S) (T1) (5–10–15–20–30) at (I1) x 600% current.


time-delay. Total clearing time is + 50 mS andresettable time -20mS for the time-delay setting.


* Pre-trip alarm pick-up current (A) (IP) (I1) x (0.7, 0.8, 0.9, 1.0) Setting tolerance ±10%* Pre-trip alarm time setting (S) (TP) 40 fixed definite time-delay.Setting tolerance ±10%* Ground fault trip pick-up current (A): (IG) Continiuously adjustable from (In) x (0.1 to 0.4)

Setting tolerance ± 15%* Ground fault trip time setting (S): (TG) Opening time (0.1-0.2-0.3-0.4-0.8) in the definite

time-delay. Total clearing time is + 50mS andresettable time is - 20mS for the time-delay settings

Note: * OptionalNote: The underlined values will be applied as standard ratings unless otherwise specified

when ordering.


Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

ndm

inut

eho

ur

T

I

IPI1

T1

I2 T2

I3

Curves based on standard settingscurves based on standard settings


Trip

pin

g T

ime

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80

90

100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

seco

nd

min

ute

hour

8 9

10

12.5 15

20

40

50


T

I

IG

I1

T1

I2 T2

I3TG

IP


Time/Current Curves

LimitorBreaker Series

Time/current characteristic curvesTL-400NE


Trip

pin

g T

ime

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80

90

100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

4000

5000

6000

7000

8000

seco

nd

min

ute

hour

T

I

IPI1

T1

I2 T2

I3

Overcurrent tripping characteristics

Time/current characteristic curvesTL-630NE, TL-800NE, TL-1250NE

CT rated current (A) (In) 630, 800, 1000, 1250Base current setting (A): (Io) (In) x (0.63-0.8-1.0)Long time-delay pick-up current (A): (I1) (Io) x (0.8-0.85-0.9-0.95-1.0) Non-tripping at (I1)




Instantaneous trip pick-up current (A) (I3) Continuously adjustable from (Io) x (3 to 12)Setting tolerance ± 20%





when ordering.


CT rated current (A) (In) 400Base current setting (A): (Io) (In) x (0.63-0.8-1.0)Long time-delay pick-up current (A): (I1) (Io) x (0.8-0.85-0.9-0.95-1.0) Non-tripping at (I1)

setting x 105% and below. Tripping at 125% and above.Long time-delay time settings (S) (T1) (5–10–15–20–30) at (I1) x 600% current.


time-delay. Total clearing time is + 50 mS andresettable time -20mS for the time-delay setting


* Pre-trip alarm pick-up current (A) (IP) (I1) x (0.7, 0.8, 0.9, 1.0) Setting tolerance ±10%* Pre-trip alarm time setting (S) (TP) 40 fixed definite time-delay.Setting tolerance ±10%Note: * OptionalNote: The underlined values will be applied as standard ratings unless otherwise specified when ordering.

Curves based on standard settings


24


Time/Current Curves

Selectivity Series


Time/current characteristic curvesXS1250SE, XS1600SE

CT rated current (A) (In) 1000, 1250, 1600Base current setting (A): (Io) (In) x (0.63-0.8-1.0)Long time-delay pick-up current (A): (I1) (Io) x (0.8-0.85-0.9-0.95-1.0) Non-tripping at (I1)




Instantaneous trip pick-up current (A) (I3) Continuously adjustable from (Io) x (3 to 12)Setting tolerance ± 20%





when ordering.


Trip

ping

Tim

e

43

2

15040

30

20

108

654

3

2

15040

30

20

108

654

3

2

10.80.6

0.50.4

0.3

0.2

0.10.08

0.060.050.04

0.03

0.02

0.010.008

0.0060.005

80 90 100

125

150

200

250

300

400

500

600

700

800

900

1000

1500

2000

2500

3000

seco

ndm

inut

eho

ur

8 9 10

12.5 15 20 40 50



T

I

IG

I1

T1

I2 T2

I3TG

IP

25

Section

Optional Accessories

26

Auxiliary Trip (AX, AXE)

Electrically indicates On/Off statusof the breaker.

Alarm Switch (AL,ALE)

Electrically indicates when thebreaker is in the “Tripped” state.

Shunt Trip (SHT)

Remote tripping of the breaker

Undervoltage Trip (UVT)

Automatically trips the breakerwhen the circuit breaker fallsbelow pre-set value. Remotetripping of the breaker is alsopossible.Note: The UVT controller isinstalled externally, when providedwith AC UVT. (Refer to page 23)

Note: The SHT and UVT cannotbe mounted in the same breaker.

Operation of AX, AXE and AL, ALE

Auxiliary switches (AX,AXE) and alarm switches (AL,ALE) ratingsApplicable breakers 250AF or smaller 400AF or larger

(including:XH250PJ and TL250NJ)

Switch type *AV39052(AXE, ALE) *V-10(AX, AL)AC Voltage (V) 480 250 125 480 250 125

Current (A) Resistive load 0.4 3 3 3 5 5Lamp load 0.05 0.3 0.5 0.3 1.5 2Inductive load 0.25 2 2 2 5 5Motor load 0.1 0.5 0.7 0.4 2 3

DC Voltage (V) 250 125 30 250 125 30Current (A) Resistive load 0.2 0.4 3 0.3 0.6 5

Lamp load 0.03 0.05 1 0.05 0.1 3Inductive load 0.03 0.05 2 0.3 0.6 4Motor load 0.03 0.05 2 0.05 0.1 3

Note:* For use in the micro current (mA) range. Contact Terasaki for details.

Switch type Breaker 'ON' Breaker 'OFF' Breaker 'TRIP' Switch type Breaker 'ON' Breaker 'OFF' Breaker 'TRIP'

AX, AXE AL, ALE

AXc1

AXb1 AXa1 ALb1 ALa1

ALc1AXc1

AXb1 AXa1

AXc1

AXb1 AXa1 ALb1 ALa1

ALc1

ALb1 ALa1

ALc1

Ratings


Internally Mounted Accessories

Overview

27


Internally Mounted Accessories

Ratings

Undervoltage trip (UVT) ratings

UVT controllerIf the UVT is for AC use a UVT controller must be installed. Standard installation of the UVTcontroller is on the left side of the breaker. However, this may be installed in a separate location(please specify). Separate installation is standard for breakers fitted with Mechanical Interlocks.A time-delay UVT controller is available with the same outside configurations (please contactTerasaki for details). For the UVT controller mounting position and accessory lead terminal blockarrangement refer to pages 74-75 of catalogue ‘98-I20E.

XH125PJ 3.4 0.83 1.6 0.71 0.4 -XH160PJXH250PJ 1.1 0.93 2.52 1.55 0.67 0.35

Shunt trip (SHT) rating

PowerBreaker

Note: Special voltages available on request. Contact Terasaki for details.Note: Shunt trip is provided with anti-burnout switch.

Controller Designations

Frame size

Instantaneous type

Time delay type

50A-250A

XCU IS

XCU ID

400A-2500A

XCU 4JS

XCU 4JD

* Configuration is for simultaneous mounting with OCRcontroller, for details on OCR controller refer to page 38of catalogue ‘98-I20E.

50A to 250A frame 400A to 2500A frame

XH400PJ, XH400PEXH630PJ, XH630PEXH800PJ, XH800PETL-100NJ 3.4 0.83 1.6 0.71 0.4 -TL-250NJ 1.1 0.93 2.52 1.55 0.67 0.35TL-400NETL-630NETL-800NETL-1250NEXS400SE, XS400SE-C, XH400SE 1.1 0.93 2.52 1.55 0.67 0.35XS630SE, XS630SE-C, XH630SEXS800SE, XH800SEXS1250SEXS1600SE

LimitorBreaker

Selectivity

Series Breaker Rated Exciting coil current [ peak value (A)] Values at the highest voltage (60Hz for AC use)voltage:110-115VAC 200-480VAC 24VDC 48VDC 100-115VDC 200-230VDC

Note: AC rated, permissible operating voltage range is 85 to 110%. DC 75 to 125%.Note: *Applicable to 200V and 400V class only.

XH125PJ 5VA 5VA 5VA 18.2 4.8 *-XH160PJ

Undervoltage trip (UVT) ratings

TL-100NJ 5VA 5VA 5VA 18.2 4.8 *-TL-250NJ 2VA 2VA 2VA 86.5 21.2 12.1TL-400NETL-630NETL-800NETL-1250NEXS400SE, XS400SE-C, XH400SE 2VA 2VA 2VA 86.5 21.2 12.1XS630SE, XS630SE-C, XH630SEXS800SE, XH800SEXS1250SEXS1600SE

LimitorBreaker

Selectivity

Series Breaker Rated Power supply, VA (with UVT controller) Exciting coil current (MA)voltage:100-120VAC 200-480VAC 300-450VAS 24DC 110-115VDC 200-230VDC

XH250PJ 2VA 2VA 2VA 86.5 21.2 12.1XH400PJ, XH400PEXH630PJ, XH630PEXH800PJ, XH800PE

PowerBreaker

Note: Tripping voltage is 35-70% of the rated voltage. Resettable voltage is 85% or less, of the rated voltage.Note: *200V DC application available on request as a special specification and equipped with resistor. Contact Terasaki for details.Note: Special voltages available on request. Contact Terasaki for details

UVT controller

688 10

0

61010

80

16

22 6

25

1518

1516

7.8

*1OCR21

9

support

59

45

57.5

Terminal screw 9

support

83

69

81.5

Terminal screw

ON

OFFUC2UC1

Small type of breakeror fuse

ON

OFF

P2P1

UVTcontroller

UVTcontroller

Small type of breakeror fuse

NOTE: Terminals UC1 andUC2 are already connected

UC2UC1

P2P1

28

Designation

FCSPWCBARREFREBPRCPFBLTPLTFLTSPMBTCFTCRTBAXCUELBEHAHLMOTOMMOHEOHJMIFMIBMIW

Description

Front connect screwSolderless terminalAttach barRear connection flat barRear connection bolt studPlug-in rear connectionPlug-in attach barPlug-in lead terminalAccessory lead terminalAccessory lead terminal (angled entry)Plug-in mounting baseTerminal cover (front connected)Terminal cover (rear connected)Interpole barrierUVT controllerEarth leakage block *Extension handleHandle lockMotor operatorOperating handle, variable depthOperating handle, panel mountedOperating handle, breaker mountedFront mechanical interlockRear mechanical interlockWire mechanical interlock

REB

MIW

REF

PFB

PMB

LTP

MIB

MIF

REB

REF

ON

OFF

ON

OFF

PRC

PRC


Externally Mounted Accessories

Overview

* Available for MCCB types XH125PJ and XH160PJ only

29



Overview

OHJ

PWC

BAR

HL

FCS

LTF/LTS

XCU

TCR

TCF

TBA

LTP

ON

OFF

ON

OFF

DF MOT

UNLOCK

LOCK

OHH

EHA

BAR

PWC

ELB

I

0

TRIP.

LOADTemBreak

T

MANUAL OPERATION

ONI

TemBreak

XH400NE

In 400A

CONTACT

INDICATION

ON

TRIPPED

OFF

MOTOR

OPERATOR

Type

XMD4

Serial

CAUTION

Connections

NOTE

OnOff

P1P2

E

OnOff

P1P2

E

PUSH TO

TRIP

source

OHE

CAUTIONARY NOTESIf the motor operator is turned ON with thebreaker OFF and the UVT de-energised,apply the power and complete one ON-OFFoperation. (The breaker cannot be turnedON). Then complete one ON operation again(The breaker can be turned ON)

When the breaker is ON and is then tripped,the ON/OFF indicator on the motor operatorwill be indicating ON until the breaker is reset.Note: The breaker’s condition may differ.Note: Allow several minutes to cool when athermal-magnetic breaker is tripped by athermal overload trip, then reset the breaker.

Reference NotesPermissible operating voltage range asfollows:AC rated, 85 to 110% of the rated voltageDC rated, 75 to 110% of the rated voltageNote: AC rated operating voltage 380V or 400-460V a power transformer is available(optional)

Requires breaker’s auxiliary switch (1b-contact). This will be wired at the factory (onrequest) when the breaker/motor operatorassemblies are ordered. However, when allthe auxiliary switch contacts are specified forother purposes, an external auxiliary relay (notsupplied) is required to be controlled by theauxiliary a-contact of the breaker and use therelay’s normally closed contact (b-contact) forautomatic reset.

Time values at the rated operating voltage.Allow a longer time for the motor operator tocomplete the operation, at lower operatingvoltage.

The motor operator is of a short time duty. Donot subject it to more than 10 continuous ON-OFF operations. If this occurs, allow the motoroperator to cool for at least 15 minutes.

Maximum values at 110V ACMaximum values at 220V ACSpecial specification, available on request.

Ratings and specifications

Padlocking Device

ON/OFF indicator

Motor driven type 1



Motor Operators (MOT)

Power Supply

OFFRESET

AUTO RESETSW

(OPTION)

LIMITSW

X2 X1

X

ON

ABCD

E

Control circuit AC and DC

Type of Motor OperatorsApplicable Breakers

Rated OperatingVoltage

Automatic Reset

Steady-state r.m.s.Amp/inrush Amp (A)

Type of operationOperating Time(s)

Control Switch RatingsPower Source Capacity (VA)Dielectric withstand voltageWeight (kg)

XH125PJXH160PJTL-100NJ••–••2.0/4.52.0/4.51.0/2.01.0/2.0––Motor driven type10.85250V, 5A100AC100V1.8

PowerBreaker Series

Limitor SeriesAC 100-110V 200-220VDC 100-110VYesNoAC100 50Hz-110V 60HzAC200 50Hz-220V 60HzDC 100V

110V

ON OFF, RESET

1

2

3

4

5

6

7

1

2

5

6

7

7

7

Note: • Yes or available,

– No or not available

Note : Resistor is fitted for AC200-220V motor•• • • : Relay : MotorXY

Colour coding indicates the true position ofthe contacts clearly: ON (red), OFF (green),TRIP (white).

Positive contact indication

Lever pumping is no longer required.

Manual ON/OFF operationwith one stroke

Closing in 60ms or less. The closing timeremains constant over repeated operations.


NOTE• : Yes or available : Maximum values at AC115V, 50Hz : Maximum values at AC230V, 50Hz : Maximum values at DC110V : Maximum values at the rated operating voltages

1

2

3

4

ø5.5 mm

padlock

Lock Plate

Breaker mounting, removal, and even settingchanges can be done without removing themotor operator.

Easy maintenance Fast closing operation

Manualoperatinghandle

Indicator

Control circuitterminals

Indicator

Lock plate

Control circuitterminalsTrip button

Manualoperatinghandle

Type XMD4 Type XMD6, XMD9Trip button

Lock plate

The breaker can be padlocked in the “OFF”position by pulling out the lock plate, and locking itwith a padlock.When the breaker is “ON”, the lock plate cannot bepulled out.Up to three locks can be used.Padlocks not supplied.

__+ +

Type of Motor OperatorsApplicable Breakers

Rated OperatingVoltage (V)

Lock in "OFF" position (standard) Manual Trip ButtonSteady-state r.m.s.Amp/inrush Amp (A)

Type of operationOperating Time(s)

Control Switch RatingsPower Source Capacity (VA)Dielectric withstand voltageThe value in brackets for 24V DCWeight (kg)

XMD4

XH400SE••••••–/3.11.2/5.7–/1.20.7/3.0–/0.81.0/4.0–/4.54.0/12.0Spring Charged0.063250V, 5A300VAAC1500V (AC500V)

4.7

XMD6XH630PJ, XH800PJXH630PE,XH800PE - TL-630NE, TL800NE

TL-1250NEXS630SE,XS630SE-C XS1250SEXH630SE,XH800SE

•••••* *–/3.11.8/6.0–/1.21.0/3.2–/0.81.1/4.2–/4.54.0/12.0Spring Charged0.063250V, 5A300VAAC1500V (AC500V)5.6

XMD9

XS1600SE–•••••

–/3.11.8/6.0–/1.21.0/3.2–/0.81.1/4.2–/4.54.0/12.0Spring Charged0.063250V, 5A300VAAC1500V (AC500V)6.4

PowerBreaker Series XH250PJ, XH400PJXH400PE

LimitorBreaker Series TL-250NJTL-400NE

Selectivity Series XS400SE,XS400SE-C

AC 100-115V 50/60Hz 200-230V 50/60HzDC 100-110V 24V

AC100 ON-115V OFF, RESETAC200 ON-230V OFF, RESETDC100 ON-110V OFF, RESETDC24V ON OFF, RESET

ON (Maximium values)OFF, RESET



Motor Operators (MOT)

Control circuit AC and DC

33

Section

Outline Dimensions

34

Plug-in

Front connected

Rear connected with motor operator

ASL: Arrangement Standard LineH : Handle Frame Centre LineL

Drilling plan

Drilling plan Panel cutout

Preparation of conductor

M8 Screw

Mounting holeInterpole barrier(removable)

Mounting block

Panel cutout dimen-sions shown give anallowance of 1.0 mmaround the handleescutcheon

for accessory wiring when necessary

M4 x 0.7 Tapped hole

Insulated stud block

Mounting plate

M8Screw

R1M6 Mounting screw

Conductor

M5 x 0.8Mounting screw

Preparation of conductor

Drilling plan

M4 x 0.7 Mountingscrew M4 x 0.7

Tappedhole

Details of connection

Outline dimensions (mm)

TemBreak Plus

XH125PJ

2518

.5

90

134

154530

90

3060

18.5

107

194

25

121

35 22 2 11989

4P3P

60

120

90

30

3P 4P

155

134

N

24

4 86

104

79

27 6 30 30

1530 30 30

18

90 1515

60

30

134

13231

.5

21.5

15 60

30

29

31.5

51.5

66.5

3P

4P

134

3P 4P

29

67

102

132

15

86.5

86

207.

8

9

17(max.)

8.5(

max

.)

57.5

54.5

ø6.5

10(m

ax.)

15(max.)

3P 4P

4P

3P

24

52

13

ø6

100

75

60

3P 4P

24

3

3028 15

86

27

86

HLHL

ASL ASL ASL

HL HL

ASL

operating handle

ASL ASLASL

ASL

HL

HL

HL

HL

HL

HL

HLHL

13

121

90

padlockfacility

35

Plug-in

Front connected


Drilling plan

M8 Screw

M4 x 0.7Mountingscrew

Drilling plan

Note: Breakers with terminal bars available on request

Conductoroverlap max.

Panel cutout dimensionsshown give an allowanceof 1.0 mm around thehandle escutcheon

R1

Panel cutout

Mounting block Drilling plan


Preparation ofconductor

With terminal bars (optional)Interpole barrier(removable)

M5 x 0.8 Mounting

Screw

M8 Screw

25 Max.conductor width

Accessory connection block

Mounting plate


M4 x 0.7 Tapped hole

Stud can be turned 90º

Mounting plate max. 5t


M4 x 0.7Tappedhole


TemBreak Plus

XH160PJ

Mounting plate


36


TemBreak Plus

TL-100NJ

80

30M4x0.7

80

28

157.

577

.5

30

90

147

67

120

90

67

7960

4 86

8.5

17

30

132

143.

551

52

4P

24

3P

177

97

89 119

6030

90

30

60

27

75

86

180

15

10

6

ø9

6730 45 15

214

24

R 1

13

2235 2

3

15

ø6

37.5

37.5

104

86

66

27

121

147

67

24

ASL ASLASL

4PLH LH

3P 4P

3P

LH

ASL

LH M8

(max

.)

(max.)

ASL

4P3P

LHLH

(max

.)

(max.)4P3P

LHLH

Interpole barrier(removable)

Mounting holescrew

Mounting screw

Preparation of Pan head screw

Conductor

Tapped hole

Drilling plan

Panel cutout

Panel cutout dimensions should give anallowance of 1.0mm around the handle escutcheon.

Note: Panel cutout shown for MCCBwithout motor operator.

ASL

Mounting screw

Mounting block

Preparation ofConductor

ø6.5 Drilling plan

M5X0.8

M4x0.7

Mounting plate

(XDM2LS)

ASL

LH

M6 mounting screwConductor

Detailsforconnection

25

274

18.5

133.

553

.525

18.5

86.5

66.5

30

51.5

30

31.5

30

ASL

LHMounting plate

Bolt stud:type XRD2

Insulated stud block

M8 screw

54.5

57.5

86

3P

4P

188

29

15

30 30

90 1515

60

29

21413

280

31.5

21.5

60 M4x0.7

ø18

66

15

66

4P3PLHLH

ø15 for accessory wiring when necessaryTapped hole

ASL

157.

577

.5

147

67


Front connected


Plug-in

37


TemBreak Plus

TL-250NJ, TL-400NE

33

8

45

214

100

30

29

45

115

45

110

103

4P

830

328

45

8

45

33

45

257015

90

107

3P

360

337

345

214.5

ø13ø13

15

25

33 45 33

45

Mounting plate

Flat bar stud : type XRP4

Stud can be turned 90

ASL ASL

LH LH

M6 tappedhole

ø15 for accessory wiring when necessary

ø36

Drilling planPanel cutout

Panel cutout dimensions showngive an allowance of 1.0mm

the line side and the load side are in a horizontal direction.

NOTE: In the standard shipment made, both terminals on

Conductoroverlap,max.

3P 4P

around the handle escutcheon.

4.5max.11

114

214

230

130

714

.5

ø11

23

M6 tapped hole

44.5

23.5

28

10

107

3P

3P

4P

4P

214

114

47

10

60

72 119

45

4P

234

4545

241

141

35

90

148

3P

60

2514

225

12118 47

20

35

20

90

140

185

70 115

45 45 45

214

114

230

130

360

110

103

145

5646

7.5

14.728

12.5

(max

.)

25(max.)

60 60 60

52.5

120

14.5

45

214

100

69

44.5

20

28

ø14

ø9

18

74

11.5

54

20

167

67

20

2727

11.5

382

Drilling plan

M10 screw

Preparation of

Hexagon socket head screw

Conductor

With Terminal Bars

(Optional) t=8


4P

ASLASLASLASL

HL

LH

LH

Values for conductors or optional terminal bars

ASL

Auxiliarycircuitterminal

ASL

LH LH

LH4P

ASL

Drilling planMounting block

Mounting angle

hole

3P

3P

M6 mounting screw

mounting hole

M8 Mountingscrew

(XDM4LS)

HL

Detailsforconnection

Conductor width, 35 max.

M10 screw

42

Note: Panel cutout shown for MCCBwithout motor operator.

4P

64

R6.5

3P

92

HL

ASL

Front connected


Plug-in


38

52.5

2010

3P 4P

N

On side 31Off side 30

3P

4P

90

140

45 4545

70 115

185

45

214

8

39

8

38

228

260

110

28 14.769

145

1037.5

28

120

44.5

14.5

56

ø14 28

23

60 6060

23.5 7 44

.5

14.5

25(max.)

12.5

(max

.)

11

46

74119

60

121

4P3P

3P 4P

15

103

ø13

334 max

228

203

214.

511

0

70

15 30

454545

25

2515

13

29

33 90 33

ø36

ø3645 45

33 3345 45 45

214

228

8

72

228

282

10

90

148

HL

122

4PMotor operatorPanel Cutout 3P

45 4545

54

134

2054

104

20

282

11.5

11.5

8

8

4P

3P

64

92

844P

9

18

20

35

47

60

134

2525

3P

HL

HL HL

HL

HLHL

HLHL

ASL

ASL

ASL ASL ASL ASL

ASL

ASL

ASL ASLASL ASL

30

28.5

28.5

HLHL HL

ASL

214.54.5max.11

345

R3

ASL

3P

4P

Front connected


Plug-in

With terminal bars (optional) Drilling plan

Preparation ofconductor

On side


M6 Mountingscrew

M10 Screw

M6Tappedhole

Off side


Mounting plate

Conductor overlapmax. for accessory wiring when necessary

R6.5

M6 Tapped hole

Panel cutoutdimensions showngive an allowance of1.0 mm around thehandle escutcheon

Note: In the normal shipment mode, both terminals on the lineside and the load side are in the horizontal direction.

M8 Mountingscrew

Accessory connection block

35 max. conductor width

M10 Screw


Mountingangle



Drilling plan

Panel cutout

Drilling plan

Mounting block

On side

Off side


TemBreak Plus

XH250PJ, XH400PJ, XH400PE, XS400SE, XS400SE-C, XH400SE

Lock plate


39

90

280

105

13

1540

121

4P3P

3P 4P

N

3P

4P

3P

4P

3P 4P

15

7.5

13

273

141

132

13

13

140

210 280

175105

70 7070

80

258

32

70

A 32

6

BA

28 14

103

80.5 145

126

117

7

70

14043 43

48

55

126

117

136

127

5570

43 70 70 70 43

1042

117

126

141

132

70 70 70

122

214.

5

820

62 45

156

147

126

117 90

70 7070

175

6218

1862

6776

303

57

253285

456

210

140

173.

575

.524

4P

3P

64

92

67

4P

11

18

60

47

90

76

2525

3P

HL HL

HL

ASLASL

ASL

Lock plate

ASL ASLASL

ASL

ASL

ASL ASL

HL

HLHL

HL

HL HL

HL

ASL

21

8

80

13

4010

231

.5

Max. 310

214.5max 11 4.5

HL

168

4PMotor operatorPanel Cutout 3P

86.5

17.5

R3

ASL

ASL: Arrangement Standard LineH : Handle Frame Centre Line


TemBreak Plus

XH630PJ, XH630PE, XS630SE, XS630SE-C, XH630SE, XH800PJ, XH800PE, XS800SE, XH800SE

Front connected

L

Note:In the normal shipment mode, both terminals on the lineside and the load side are in the horizontal direction.

Panel cutout dimensionsshown give an allowanceof 1.0 mm around thehandle escutcheon


Extension handle(removable)

M8 Mountingscrew

Drilling plan

M8 Tappedhole

(Neutral: N)

Mounting plate



M8 Tapped hole

Mounting block

Conductor overlap max.

R6.5

M10 Mountingscrew

Accessory connectionblock

Mountingangle

Drilling plan

40 max. conductor width

M16 Screw

Panel cutout

Drilling plan

Conductoroverlapmax.



Plug-in

Breaker type A B N

XH630PJ 8 34 36

XH630PE, XS/XH630SE, XS630SE-C 8 36 36

XH800PJ 10 35 36

XH800PE, XS800SE, XH800SE 10 36 36

40

Front connected



Plug-in


TemBreak Plus

XS1250SE

Panel Cutout

41


TemBreak Plus

TL-630NE, TL-800NE, TL-1250NE, XS1600SE

Front connected



Draw-out

Motor operatorpanel cutout (*)

* Panel cutout dimensions shown givean allowance of 1mm around thehandle escutcheon or 1.5mm aroundthe motor operator frame

43

Section

Selectivity Table

XE100NS

XS125CJ

XS125NJ

XH125NJ

XH125PJ

XS160NJ

XH160NJ

XH160PJ

XE225NS

XS250NJ

XS250PJ

XH250NJ

XH250PJ

XH250PE

XE400NS

XS400CJ

XS400NJ

XH400PJ

XS400SE-C

XS400SE

XH400SE

XH400PE

XE600NS

XS630CJ

XS630NJ

XH630PJ

XS630SE-C

XS630SE

XH630SE

XH630PE

T

T

T

35

35

15

35

25

15

15

15

25

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

25

25

T

25

25

25

25

25

25

25

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

50

50

T

T

T

50

T

T

50

50

20

30

30

30

30

30

30

30

T

T

T

T

T

T

T

T

T

T

T

T

50

50

T

T

T

50

T

T

50

50

20

30

30

30

30

30

30

30

UpstreamIcu @

415 400 50 50 65 65 50 50 65 65 50 50 65 65 65 85 85 100

XS400SE XH400SE XS630SE XH630SE XS800SE XH800SE XS1250SE XS1600SE

Notes: 1. The letter 'T' denotes Total Selectivity up to the breaking capacity of lower rated Icu MCCB. 2. The symbol '**' denotes that selectivity is only obtained up to the level of the upstream instantaneous trip 3. All pick-up current and time delay settings are to be set at maximum for upstream MCCBs

10 15

14 18

25 30

50 50

50 50

25

35

50

50

50 50

15 18

25 35

35 35

50 50

65 65

65 65

25 25

35 35

50 50

65 65

35 35

50 50

65 65

65 65

25 25

35 45

50 65

85 100

35 40

50 50

65 65

65 65

T

T

T

T

T

T

T

T

T

T

T

T

10

10

10

10

10

10

10

10

10

10

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

10

10

10

10

10

10

10

10

10

10

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

25

25

T

25

25

25

25

25

25

25

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

50

50

T

T

T

50

T

T

50

50

20

30

30

30

30

30

30

30

T

T

T

T

T

T

T

T

T

T

T

T

50

50

T

T

T

50

T

T

50

50

20

30

30

30

30

30

30

30

T

T

T

T

T

T

T

T

T

T

T

T

25

25

T

25

25

25

25

25

25

25

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

25

25

T

25

25

25

25

25

25

25

**

**

**

**

**

**

**

**

T

T

T

35

35

15

35

25

T

15

15

25

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

T

T

T

35

35

15

35

25

15

15

15

25

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

T

T

T

35

35

15

35

25

T

15

15

25

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

10

10

10

10

10

10

10

10

10

10

**

**

**

**

**

**

**

**

T

T

T

T

T

T

T

T

T

T

T

T

10

10

10

10

10

10

10

10

10

10

**

**

**

**

**

**

**

**

Downstream

Notes: 4. The above table is in accordance with IEC-947-2 Appendix A 5. Figures are shown with 415v information in white and 400v information in black 6. Selectivity figures for the XH-PE series are the same as the

XS-SE. Please contact Terasaki for further details.

Application

TemBreak Plus

Selectivity Table for 415V and 400V

PlusOVERSEAS NETWORK

TERASAKI (EUROPE) LTD.80 Beardmore Way, Clydebank Industrial Estate, Clydebank, G81 4HT. SCOTLAND (U.K.)Telephone: 44-141-941-1940 / Fax: 44-141-952-9246web: www.terasaki.com

TERASAKI ITALIA s.r.l.Via Campania 4/6, 20090 Segrate, Milano, ITALYTelephone: + 39-02-2137574 / Fax: + 39-02-26922931web: www.terasaki.it

TERASAKI ESPAÑA, S.A.Roma Street, s/n 08400 Granollers, Barcelona, SPAINTelephone: +34-93-8796050 / Fax: +34-93-870-3905web: www.terasaki.es

TERASAKI CIRCUIT BREAKERS (S) PTE. LTD.51 Tannery Lane #10-02, Sharely Warehouse, Singapore 1334, SINGAPORETelephone: +65-7449752 / Fax: +65-7487592

TERASAKI ELECTRIC (M) SDN. BHD.Lot 3 Jalan 16/13-D, 40000 Shah Alam,Selangor, MALAYSIATelephone: +60-3-5510-3820 / Fax: +60-3-55103763

TERASAKI DO BRASIL S.A.Rua Campo Grande No. 3700, Campo Grande, Rio de Janeiro, BRAZILTelephone: 021-413 4222 / Telex: 2123178 TBRJ BR / Fax: 21-3941875

ELECTRIC CO., LTD.Head Office: 7-2-10 Hannancho, Abenoku, Osaka, JAPANTelephone: 81-6-692-1131 / Telex: 526-7749 TTSAKI / Cable: TERASAKI OSAKACircuit Breaker Division: 7-2-10 Kamihigashi, Hiranoku, Osaka, JAPANTelephone: 81-6-692-1134 / Telex: 526-7769 TSKNFB / Fax: 81-6-695-2296web: www.terasaki.jp

JUNE 2000 CATALOGUE No. '00 - I26ERatings and specifications covered in this catalogue may be subject to change without notice.

innovators in protection technlogy tembreak plus · during a fault condition, a circuit breaker...

Documents