installa on instruc onsvag 2.0 tsi und tfsi longitudinally mounted datum: 13.12.2012 seite:6
TRANSCRIPT
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:1
The product described in the guidance was developed, manufactured and controlled consi‐dering the necessary safety reguirements.
The product must be installed properly to ensure a proper func on and avoid danger for persons and things.
Please read this installa onguide inclusive safety instruc ons carefully.
Scope of supply:
Quan ty ar cle
1x Tuningbox
1x loom
1x Bridge plug
1x Fastening kit
1. Open the hood.
2.Turn the igni on off!
3.Remove the igni onkey!
4.Close and lock all doors!
5.Do not open any doors while installing the tuning‐kit!
6.Wait 5 minutes before beginning the installa on
In order to avoid damages at electronic vehicle com‐ponents, you have to be sure that you have done all necessary methods for electosta c discharge .
Install the electronic in an waterproof and vibra -onless place. Do not make any changes at the tuning‐kit!
Do not expand or shorten the loom.
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:2
overview
boost pressure sensor
camsha posi on sensor
thro le valve switch
Overview:
The tuningkit has to be a ached to the following points:
boost pressure sensor
thro le valve switch
camsha posi on sensor
Required tools:
cu ers
Vorbereitung:
Move the individual strands of the loom to the associated plug connectors
Put the required tools by your side ( if needed )
Take the fastening material at your side
To get the maximum power gain , you have to use „super plus“ (98 ROZ)
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:3
cover
1a
1b
cover Before you could begin in‐stalling the tuningkit, you have to remove the engine cover.
The engine cover is fixed with clips
1. Prepera on
1b. cover
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:4
camsha posi on sensor 2a
2b
2. camsha posi on sensor
Disconnect the plug from the camsha posi on sen‐sor.
A ach the camsha posi ‐on sensor plug to the new loom
Connect the plug of the new loom to the camsha posi on sensor.
camsha posi on sensor
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:5
thro le valve switch
3a
3b
3. thro le valve switch
Disconnect the plug from the thro le body sensor.
A ach the manifold air pressure plug to the new loom
Connect the plug of the new loom the thro le body sensor
thro le valve switch
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:6
4a
4b
4. boost pressure sensor
Disconnect the plug from the boost pressure sensor.
A ach the boost pressure sensor plug to the new loom
Connect the plug of the new loom to the boost pressure sensor
boost pressure sensor
boost pressure sensor
-
Installa on instruc ons
VAG 2.0 TSI und TFSI longitudinally mounted
Datum: 13.12.2012 Seite:7
5
6
Finally install the cable to‐wards a suitable posi on
The plugs must be engage, so that a safe connec on is ensured
Fix the cable with cable es
Connect the tuningbox to the new loom
By using the jumper the vehicle is put in the original condi on.
As soon as you connect the cable loom with the jumper plug the car is in original condi on.
5. tuningbox
6. jumper plug