installation guide - tp-linkstatic.tp-link.com/7106507529_t1600g_ig.pdf · i about this...

T1600G-18TS (TL-SG2216)T1600G-28TS (TL-SG2424) / T1600G-52TS (TL-SG2452)

T1600G-28PS (TL-SG2424P) / T1600G-52PS (TL-SG2452P)

Business Networking Solution

Installation GuideJetStream Gigabit Smart Switch

I

About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the external components of the switch.

Chapter 2 Installation. This chapter illustrates how to install the switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning damage.

Chapter 4 Connection. This chapter illustrates how to do the physical connection of the switch.

Chapter 5 Configuration. This chapter instructs you to configure the switch via Web Interface and CLI commands.

Appendix A Troubleshooting.

Appendix B Specifications.

Audience This Installation Guide is for:Network Engineer Network Administrator

Conventions • Some models featured in this guide may be unavailable in your country or region. For local sales

information, visit http://www.tp-link.com.

• The figures in Chapter 2 to Chapter 5 are for demonstration purposes only. Your switch may differ in appearance from that depicted.

• This Guide uses the specific formats to highlight special messages. The following table lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may result in device damage.

Remind to take notice. The note contains the helpful information for a better use of the product.

Related Document The User Guide and CLI Reference Guide of the product are provided on the resource CD. To obtain the latest product information, please visit the official website: http://www.tp-link.com

About This Installation Guide

JetStream Gigabit Smart Switch

II

Contents

Contents

Chapter 1 Introduction ——————————— 011.1 Product Overview .................................................011.2 Appearance ....................................................................01

Chapter 2 Installation ——————————— 092.1 Package Contents ...............................................092.2 Safety Precautions ..............................................092.3 Installation Tools ...................................................112.4 Product Installation .............................................12

Chapter 3 Lightning Protection ——————— 143.1 Cabling Reasonably .............................................143.2 Connect to Ground ..............................................16

Chapter 4 Connection ——————————— 204.1 Ethernet Port ..........................................................204.2 SFP Port ...................................................................204.3 Verify Installation ..................................................204.4 Power On .................................................................214.5 Initialization .............................................................21

Chapter 5 Configuration —————————— 225.1 ConfiguretheSwitchviaGUI ...........................225.2 ConfiguretheSwitchUsingCLI ......................23

Appendix A Troubleshooting ———————— 24

Appendix B Hardware Specifications ———— 25


Introduction 01

Chapter 1 Introduction

1.1 Product Overview

TP-Link Gigabit Smart Switch, designed for workgroups and departments, provides wire-speed performance and abundant L2 and L2+ management features. It provides a variety of service features and multiple powerful functions with high security.

The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation increases aggregated bandwidth, optimizing the transport of business critical data. SNMP, RMON, WEB and CLI Log-in bring abundant management policies. TP-Link Gigabit Smart Switch integrates multiple functions with excellent performance, and is friendly to manage, which can fully meet the need of the users demanding higher networking performance.

T1600G-28PS/T1600G-52PS is also a Power Sourcing Equipment (PSE*). All the Ethernet RJ45 ports on the switch support Power over Ethernet (PoE*) function, which can automatically detect and supply power with those powered devices (PDs*) complying with IEEE 802.3af and IEEE 802.3at.

Note: ■ *PSE is a device (switch or hub for instance) that will provide power in a PoE

setup. ■ *PoE is a technology that describes a system to transmit electrical power, along

with data, to remote devices over standard twisted-pair cable in an Ethernet network.

■ *PD is a device powered by a PSE and thus consumes energy. Examples include powering IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers etc.

1.2 Appearance

■ Front PanelThe front panel of T1600G-18TS is shown as the following figure.Figure 1-1 Front Panel of T1600G-18TS

10/100/1000Mbps RJ45 Port

SFP Port

Reset

LEDs


Introduction02

LEDs

LED Status Indication

PWROn The switch is powered onOff The switch is powered off or power supply is abnormalFlashing Power supply is abnormal

SYSFlashing The switch is working normallyOn/Off The switch is working abnormally

Link/ActOn There is a device connected to the corresponding port but no

activityFlashing Data is being transmitted or receivedOff No device is connected to the corresponding port

1000MbpsOn A 1000Mbps device is connected to the corresponding port

Off A 10/100Mbps device or no device is connected to the corresponding port

ResetPress this button for 5 seconds or above to reset the software setting back to factory default settings.

10/100/1000Mbps RJ45 PortDesigned to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Link/Act LED and a 1000Mbps LED.

SFP Port

Designed to install the SFP module. T1600G-18TS features 2 individual SFP ports and supports 1000M SFP module connection only.

The front panel of T1600G-28TS is shown as the following figure.Figure 1-2 Front Panel of T1600G-28TS


SFP Port

Reset

LEDs


Introduction 03

LEDs



SYSFlashing The switch is working normallyOn/Off The switch is working abnormally

Link/ActOn There is a device connected to the corresponding port but no

activityFlashing Data is being transmitted or receivedOff No device is connected to the corresponding port

1000MbpsOn A 1000Mbps device is connected to the corresponding port



10/100/1000Mbps RJ45 PortDesigned to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Link/Act LED and a 1000Mbps LED.

SFP Port

Designed to install the SFP module. T1600G-28TS features 4 individual SFP ports and supports 1000M SFP module connection only.

The front panel of T1600G-52TS is shown as the following figure.Figure 1-3 Front Panel of T1600G-52TS


SFP Port

LEDs

Reset



Introduction04

LEDs



SYSFlashing The switch works properlyOn/Off The switch works improperly

10/100/1000Mbps (port 1-48)

GreenOn A 1000Mbps device is connected to the corresponding

port, but no activityFlashing Data is being transmitted or received

YellowOn A 10/100Mbps device is connected to the

corresponding port, but no activityFlashing Data is being transmitted or received

Off No device is connected to the corresponding port

Link/Act(port 49-52)

On A 1000Mbps device is connected to the corresponding SFP port but no activity

Flashing Data is being transmitted or received

Off A 10/100Mbps device or no device is connected to the corresponding SFP port

10/100/1000Mbps RJ45 PortDesigned to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding 10/100/1000Mbps LED.

SFP PortDesigned to install the SFP module. T1600G-52TS features 4 individual SFP ports and supports 1000M SFP module connection only.

The front panel of T1600G-28PS is shown as the following figure.Figure 1-4 Front Panel of T1600G-28PS

Reset

LEDs


SFP Port

LED Mode Switch Button


Introduction 05

LEDs

T1600G-28PS has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission status. When the PoE LED is on, the port LED is indicating the power supply status. By default, the Speed LED is on. Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.

When the Speed LED is on, the port LED is indicating the data transmission status.


PWR

On The switch is powered on

Off The switch is powered off or power supply is abnormal

Flashing Power supply is abnormal


FANGreen All the fans work properlyYellow Not all the fans work properly

Speed or PoE

(port 1-24)

GreenOn A 1000Mbps device is connected to the





1000Base-X

(port 25-28)

On A 1000Mbps device is connected to the corresponding portFlashing Data is being transmitted or received


When the PoE LED is on, the port LED is indicating the power supply status.





PoE Max

On The remaining PoE power≤7W

Flashing The remaining PoE power keeps ≤7W after this LED is on for 2 minutes

Off The remaining PoE power＞7W


Introduction06


Speed or PoE(port 1-24)

GreenOn The port is supplying power normally

Flashing The supply power exceeds the corresponding port's maximum power

Yellow On Overload or short circuit is detectedOff No PoE power supply is provided on the port

LED Mode Switch ButtonPress this button to switch the LED status indication between Speed and PoE.

ResetPress this button for five seconds or above to reset the software setting back to factory default settings.

10/100/1000Mbps RJ45 PortDesigned to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Speed or PoE LED.

SFP Port

Designed to install the SFP module. T1600G-28PS switch features 4 features 4 individual SFP ports and supports 1000M SFP module connection only.

The front panel of T1600G-52PS is shown as the following figure.Figure 1-5 Front Panel of T1600G-52PS

Reset

LEDs

10/100/1000Mbps RJ45 PortSFP Port


LEDs

T1600G-52PS has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission status. When the PoE LED is on, the port LED is indicating the power supply status. By default, the Speed LED is on. Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.


Introduction 07

When the Speed LED is on, the port LED is indicating the data transmission status.


PWR






Speed or PoE (port 1-48)

GreenOn A 1000Mbps device is connected to the





1000Base-X

(port 49-52)

On A 1000Mbps device is connected to the corresponding port.Flashing Data is being transmitted or received

Off A 10/100Mbps device or no device is connected to the corresponding port.

When the PoE LED is on, the port LED is indicating the power supply status.


PWR






PoE Max

On The remaining PoE power≤7W

Flashing The remaining PoE power keeps ≤7W after this LED is on for 2 minutes

Off The remaining PoE power≥7W

Speed or PoE(port 1-48)

GreenOn The port is supplying power normally

Flashing The supply power exceeds the corresponding port's maximum power

Yellow On Overload or short circuit is detectedOff No PoE power supply is provided on the port


Introduction08


Press this button to switch the LED status indication between Speed and PoE.

ResetPress this button for five seconds or above to reset the software setting back to factory default settings.

10/100/1000Mbps RJ45 PortDesigned to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Speed or PoE LED.

SFP Port

Designed to install the SFP module. T1600G-52PS switch features 4 individual SFP ports and supports 1000M SFP module connection only.

■ Rear PanelThe rear panel of T1600G-18TS/ T1600G-28TS/ T1600G-52TS/ T1600G-28PS/ T1600G-52PS features a Kensington security slot, a grounding terminal and a power socket. Here we take T1600G-28TS for example.Figure 1-6 Rear Panel

Grounding Terminal

Power Socket

Kensington Security Slot

Kensington Security SlotSecure the lock (not provided) into the security slot to prevent the device from being stolen.

Grounding TerminalThe switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed information, please refer to Chapter 3 Lightning Protection.

Power Socket Connect the female connector of the power cord here, and the male connector to the AC (Alternating Current) power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage.

Caution: Please use the provided power cord.


Installation 09

Chapter 2 Installation

2.1 Package Contents

Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor.

One Resource CD

One Switch One Power Cord This Installation Guide

Two mounting brackets, eight screws and four rubber feet

Installation Guide

Business Networking Solution

2.2 Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe the following rules.

■ Safety Precautions ■ Keep the power off during the installation. ■ Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good skin

contact and is well grounded. ■ Use only the power cord provided with the switch. ■ Make sure that the supply voltage matches the specifications indicated on the rear

panel of the switch. ■ Ensure the vent hole is well ventilated and unblocked. ■ Do not open or remove the cover of the switch. ■ Before cleaning the device, cut off the power supply. Do not clean it by the waterish

cloth, and never use any other liquid cleaning method.


Installation10

■ Site Requirements

Temperature/Humidity

40℃

0℃

Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.

Environment Temperature Humidity

Operating 0℃ to 40℃ 10% to 90%RH Non-condensing

Storage -40℃ to 70℃ 5% to 90%RH Non-condensing

Clearness

The dust accumulated on the switch can be absorbed by static electricity and result in poor contact of metal contact points. Some measures have been taken for the device to prevent static electricity, but too strong static electricity can cause deadly damage to the electronic elements on the internal circuit board. To avoid the effect of static electricity on the operation of the switch, please attach much importance to the following items:

■ Dust the device regularly, and keep the indoor air clean. ■ Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference

Electronic elements including capacitance and inductance on the device can be affected by external interferences, such as conducted emission by capacitance coupling, inductance coupling, and impedance coupling. To decrease the interferences, please make sure to take the following measures:

■ Use the power supply that can effectively filter interference from the power grid. ■ Keep the device far from high-frequency, strong-current devices, such as radio

transmitting station. ■ Use electromagnetic shielding when necessary.


Installation 11

Lightning Protection

Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken.

■ Ensure the rack and device are well earthed. ■ Make sure the power socket has a good contact with the ground. ■ Keep a reasonable cabling system and avoid induced lightning. ■ Use the signal SPD (Surge Protective Device) when wiring outdoor.

Note: For detailed lightning protection measures, please refer to Chapter 3 Lightning Protection.

Installation Site

When installing the device on a rack or a flat workbench, please note the following items:

■ The rack or workbench is flat and stable, and sturdy enough to support the weight of 5.5kg at least.

■ The rack or workbench has a good ventilation system. The equipment room is well ventilated.

■ The rack is well grounded. Keep the power socket less than 1.5 meters away from the device.

2.3 Installation Tools

■ Phillips screwdriver ■ ESD-preventive wrist wrap ■ Cables

Note: These tools are not provided with our product. If needed, please self purchase them.


Installation12

2.4 Product Installation

■ Desktop Installation

To install the device on the desktop, please follow the steps:

1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings.

2. Remove the adhesive backing papers from the rubber feet.

3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.Figure 2-7 Desktop Installation

Feet

Bottom of the DeviceNotch

■ Rack Installation

To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below:

1. Check the grounding and stability of the rack.

2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws, as illustrated in the following figure.Figure 2-8 Bracket Installation

Rack-mounting Bracket

Screw

3. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure.


Installation 13

Figure 2-9 Rack Installation

Rack

Caution: ■ Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.


Lightning Protection14

Chapter 3 Lightning Protection

3.1 Cabling Reasonably

In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices.

Note: It 's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.

■ Requirements for Cabling Outdoors ■ Aerial cabling without safeguard is not allowed.

■ It’s not allowed cabling down the building to connect network devices in different floors.

■ Outdoor cables should be buried and paved to the indoor through basement. A piece of steel wire should be paved underground along the pipe and connected to the lightning protection terminal of the building for shielding. Before connecting the cable to the device, install a signal lightning arrester on the corresponding port.

■ When an aerial cable is set up, the cable should be through a metal pipe (15m long at least) before coming into the building. The two ends of this metal pipe should be grounded. Before connecting the cable to the device, install a signal lightning arrester on the corresponding port.

■ It’s not necessary to pave STP cables through pipes. The shielded layer of STP cable should be well grounded. Before connecting the cable to the device, install a signal lightning arrester on the corresponding port.


Lightning Protection 15

■ Requirements for Cabling IndoorsWhen cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor.

■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible.

■ Requirements for the distance between Ethernet cable and other pipelines are shown in the table.

Other PipelinesEthernet CableMin Parallel Net Length L (mm)

Min Parallel-overlapping Net Height H (mm)

Down-conductor 1000 300

PE 50 20

Service pipe 150 20

Compressed air pipe 150 20

Thermal pipe (not wrapped) 500 500

Thermal pipe (wrapped) 300 300

Gas pipe 300 20

The two diagrams below demonstrate parallel net length and parallel-overlapping net height.

Note: The above minimum net length/height is required when metal raceway is not used. If any requirements cannot be met, you can add a steel tube or metal raceway for shielding.

■ Requirements for the distance between Ethernet cable and high-power electric devices are in following tables.

Cable Pave Way Min Parallel Length (mm)

<2kVA powerline

Parallel cabling 130

One is in the grounded metal raceway or metal pipe 70The both are in the grounded metal raceway or metal pipe 10



Cable Pave Way Min Parallel Length (mm)

2~5kVA powerline



>5kVA powerline



Device Min Distance (m)

Switch case 1.00

Transformer room 2.00

Elevator tower 2.00Air-conditioner room 2.00

3.2 Connect to Ground

Connecting the device to ground is to quickly release the lightning over-voltage and over-current of the device, which is also a necessary measure to protect the body from electric shock.

In different environments, the device may be grounded differently. The following will instruct you to connect the device to the ground in two ways, connecting to the ground via the power supply or connecting to the ground via the grounding terminal. Please connect the device to ground in the optimum way according to your specific operation environment.

Note: For the device without grounding terminal, please refer to the f irst way Connecting to the Ground via the Power Supply only.

■ Connecting to the Ground via the Power SupplyIf the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure.



Figure 3-1 Connecting to the Ground via Power Supply

Switch (Rear Panel) AC Power Cord (with PE cable)

Note: ■ The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.

■ If you intend to connect the device to the ground via the PE (Protecting Earth) cable of AC power cord, please make sure the PE (Protecting Earth) cable in the electrical outlet is well grounded in advance.

■ Connecting to the Ground via the Grounding Terminal

Use the grounding bar

If the device is installed in the Equipment Room, where a grounding bar is available, you are recommended to connect the device to the grounding bar as shown in the following figure.Figure 3-2 Connecting to the Grounding Bar

Switch (Rear Panel)

Ground Cable

Grounding Terminal

Grounding Bar

Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them.



Equipotential Bonding

Equipotential Bonding is the practice of intentionally electrically connecting all earthed systems to the same grounding grid or connecting the grounding grids of all the earthed systems together through the ground or overground metal so as to create an earthed equipotential zone. When lightning occurs, the high voltage produced by lightning current in all systems will meanwhile exist in their ground cables, and thus all ground cables have the same electrical potential and basically eliminate the electric strikes between the systems.

The figure below illustrates how to practice equipotential bonding in a network.Figure 3-3 Equipotential Bonding

Grounding Terminal Equipotential Bonding Cable

Grounding Bar Ground Cable

When equipotential bonding, please note that the cable should be copper wrapped Kelly with its area being 6mm2 at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point.

Note: The equipotential bonding cable and ground cable are not provided with our product. If needed, please self purchase it.

Use Lightning Arrester

Power lightning arrester and signal lightning arrester are used for lighting protection.

Power lightning arrester is used for limiting the voltage surge due to a lightning. If an outdoor AC power cord should be directly connected to the device, please use a power lightning arrester.

Note: Power lightning arrester is not provided with our product. If needed, please self purchase it.



Signal lightning arrester is used to protect RJ45 ports of the device from lightning. When cabling outdoors, please install a signal lightning arrester before connecting the cable to the device.

When purchasing or using a signal lightning arrester, please observe the following rules:

■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester.

■ Install signal lightning arrester near the protected device and connect it to the ground via a shorter ground cable.

Figure 3-4 Use Lightning Arrester

Ethernet CableEquipotential Bonding CableGrounding Terminal

Signal Lightning Arrester Device

Note: Signal lightning arrester is not provided with our product. If needed, please self purchase it.


Connection20

Chapter 4 Connection

4.1 Ethernet Port

Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown.Figure 4-1 Connecting the RJ45 Port

RJ45 Port RJ45 Cable

4.2 SFP Port

Connect the SFP port to a SFP module as shown below.Figure 4-2 Inserting the SFP Module

SFP Port

SFP Module

4.3 Verify Installation

After completing the installation, please verify the following items: ■ There are 5~10cm of clearance around the sides of the device for ventilation and the

air flow is adequate. ■ The voltage of the power supply meets the requirement of the input voltage of the device. ■ The power socket, device and rack are well grounded. ■ The device is correctly connected to other network devices.


Connection 21

4.4 Power On

Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector into a power outlet as the following figure shown.Figure 4-3 Connecting to Power Supply

1

2

Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.

4.5 Initialization

After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly. During this time, its LED indicators will respond in the following order:

1. The PWR LED lights on all the time. The SYS LED and the LED indicators of all the ports keep off.

2. After about one minute, the LED indicators of all the ports will flash momentarily and then turn off.

3. A few seconds later, the SYS LED indicator will flash, which represents a successful initialization.


Configuration22

Chapter 5 Configuration

5.1 Configure the Switch via GUI1. To access the GUI of the switch, open a web browser and type the default

management address http://192.168.0.1 in the address field of the browser, then press the Enter key.Figure 5-1 Web Browser

Note: To log in to the GUI of the switch, the IP address of your PC should be set in the same subnet addresses of the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0.For the detailed instructions as to how to do this, please refer to Appendix B in the User Guide on the Resource CD.

2. Enter admin for the default User Name and Password, both in lower case letters. Then click the Login button or press the Enter key.Figure 5-2 Login

3. After a successful login, the main page will appear as the following figure, and you can configure the function by clicking the setup menu on the left side of the screen.


Configuration 23

Figure 5-3 Main Page of the Switch

5.2 Configure the Switch Using CLI

You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the following steps:1. Make sure the switch and the PC are in the same LAN. Click Start and type in "cmd"

in the Search programs and files window and press the Enter button.Figure 5-4 Run Window

2. Type telnet 192.168.0.1 in the command prompt shown as Figure 5-5, and press the Enter button.Figure 5-5 Connecting to the Switch


24

Appendix A Troubleshooting

Q1. What could I do if I forgot the username and password of the switch?

Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin.

Q2. Why does the PWR LED work abnormally?

The PWR LED should be lit up when the power system works normally. If the PWR LED worked abnormally, please take the following steps:

1. Make sure that the power cable is connected properly, and the power contact is normal.2. Make sure the voltage of the power supply meets the requirement of the input voltage of

the switch.

Q3. What should I do if I cannot access the web management page?

Please try the following:

1. Check every port LED on the switch and make sure the Ethernet cable is connected properly.

2. Try another port on the switch and make sure the Ethernet cable is suitable and works normally.

3. Power off the switch and, after a while, power it on again.4. Make sure the IP address of your PC is set within the subnet of the switch.5. If you still cannot access the configuration page, please restore the switch to its factory

defaults. Then the IP address of your PC should be set as 192.168.0.x ("x" is any number from 2 to 254) and Subnet Mask as 255.255.255.0.

Appendix A Troubleshooting


25

Appendix B Specifications

Item Content

Standards

IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3z, IEEE 802.3x, IEEE 802.1p, IEEE 802.1q, IEEE 802.1x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w

IEEE 802.3af/at (T1600G-28PS/T1600G-52PS)

Transmission Medium

10Base-T: UTP/STP of Cat. 3 or above (maximum 100m)

100Base-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100m)

1000Base-T: 4-pair UTP/STP of Cat. 5e and Cat. 6 or above (maximum 100m)

1000Base-X: MMF or SMF SFP Module (Optional)

LEDs

T1600G-18TS: PWR, SYS, 1000Mbps, Link/Act

T1600G-28TS: PWR, SYS, 1000Mbps, Link/Act

T1600G-52TS: PWR, SYS, 10/100/1000Mbps (port 1-48), Link/Act (port 49-52)

T160 0 G -28 PS: PW R , SYS , FA N , PoE M A X , Speed or PoE ( por t 1-24) , 1000BASE-X (port 25-28), Speed, PoE

T1600G-52PS: PWR, SYS, FAN, PoE MA X, Speed and PoE (por t 1-48), 1000BASE-X (port 49-52), Speed, PoE

Operating Temperature 0℃ to 40℃

Storage Temperature -40℃ to 70℃

Operating Humidity 10% to 90%RH Non-condensing

Storage Humidity 5% to 90%RH Non-condensing

AppendixBSpecifications

FCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

ПродуктсертифікованозгідносправиламисистемиУкрСЕПРОнавідповідністьвимогамнормативнихдокументівтавимогам,щопередбаченічиннимизаконодавчимиактамиУкраїни.

Safety Information• When product has power button, the power button is one of the way to shut off the product; when

there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

• Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

• Avoid water and wet locations.

BSMI Notice安全諮詢及注意事項

1) 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

2) 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

3) 注意防潮，請勿將水或其他液體潑灑到本產品上。

4) 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

5) 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

6) 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

7) 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某

些適當的對策。

Industry Canada StatementCAN ICES-3 (A)/NMB-3(A)

Explanation of the symbols on the product label

Symbol Explanation

AC voltage

Indoor use only

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A

© 2017 TP-Link 7106507529 REV2.1.0

The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.

For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code.

installation guide - tp-linkstatic.tp-link.com/7106507529_t1600g_ig.pdf · i about this...

Documents