installation honda musiclink™ 2007 odyssey …

© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33176 (0607) 1 of 12

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

JULY 2006

08B28-SHJ-1000-91

2007 ODYSSEYHONDA MUSICLINK™(FOR I-POD®)

PARTS LIST

Attachment Kit (sold separately)P/N 08A28-1H1-800

4 Cushion tapes

Holder cushion

Grommet

8 Wire ties

2 Long wire ties

Honda MusicLink Adapter Kit (sold separately)P/N 08A28-1H1-100

Honda MusicLink adapter unit

Bus cable

MusicLink harness

CD-ROM

Quick reference guide

Bus Cable 2 Port (sold separately)P/N 08A31-0F1-000

Bus cable 2 port

AII 33176

2 of 12 AII 33176 (0607) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.

5727010B

5513151B

5513231B

BUS CABLE

MUSICLINKHARNESS

MUSICLINKADAPTERUNIT

AUDIOUNIT

VEHICLECONNECTORCENTER

PANEL

VEHICLECONNECTOR

CLIPS (10)

BUS CABLE

MUSICLINKHARNESS


NAVIGATIONUNIT

With Navigation System

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

If the your vehicle is equipped with a navigationsystem, go to step 22 ; if not, continue with step 3.

3. Place the shift lever in the N (Neutral) position.

TOOL AND SUPPLIES REQUIRED#2 Phillips screwdriverFlat-tip screwdriverDiagonal cuttersScissorsRatchet10 mm Socket10 mm Combination wrenchesDrill motorDrill bit (3 mm)19 mm Hole saw (3/4")Electrical tapeFelt-tip penPushpinEye protectionIsopropyl alcohol

Illustration of the MusicLink System Installed onthe vehicle

Without Navigation System

4. Remove the center panel (ten clips and disconnectthe connectors).


4219041B

5513030B

4324041B

CLIPS (2)VEHICLECONNECTORS (6)

SELF-TAPPINGSCREW AUDIO UNIT

4324021B

GLOVE BOX

DAMPERARM

COVER

GLOVE BOX

RETAINING TAB

STOPPERS (2)

SCREWS (2)

GLOVE BOX

AUDIO UNITOPENING BUS

CABLE

GLOVE BOXOPENING

DIN CONNECTOR

VEHICLEHARNESS

5. Remove the audio unit (three self-tapping screws,two clips, and disconnect the vehicle connector).

6. Remove the damper arm cover and disconnect thearm.

7. Open the glove box and remove the two stoppersby releasing the two retaining tabs. Remove thetwo screws that fasten the glove box, then removethe glove box.

8. Route the DIN connector end of the bus cable fromthe audio unit opening to the glove box opening.

9. Secure the BUS cable.


5702091B

5513051B

5512040B

14-PINCONNECTORS (2)

Align

CUSHIONTAPES (2)

BUSCABLE

VEHICLE 14-PINCONNECTOR(for XM radio) orPLAYER BUS CABLE14-PIN CONNECTOR

BUS CABLE2 PORT

5513040B

VEHICLEHARNESS

AUDIO UNITOPENING

WIRETIE

VEHICLE 20-PINCONNECTOR

(Align.)BUS CABLE14-PINCONNECTOR

(Align.)

BUS CABLE2 PORT 14-PINCONNECTOR

AUDIO PANELOPENING

VEHICLEHARNESS

BUSCABLE

BUS CABLE2 PORT

WIRETIE

WIRETIE

VEHICLE 20-PINCONNECTOR

Without the XM Radio or the Option Player:• Align the bus cable 14-pin connector with vehicle

20-pin connector and secure bus cable to thevehicle harness with the two wire ties.

With the XM Radio or the Option Player:

• Connect the bus cable 14-pin connector and vehicle14-pin connector (for XM radio) or player bus cable14-pin connector to the bus cable 2 port 14-pinconnectors.

• Attach one cushon tape around each bus cable 2port 14-pin connector.

• Bundle up the vehicle harness or player bus cable.

• Secure the bus cable and bus cable 2 port with thetwo wire ties as illustrated.

• Align the bus cable 2 port 14-pin connector with thevehicle 20-pin connector, and secure the bus cableto the vehicle harness with two wire ties.

BUS CABLE 14-PINCONNECTOR

VEHICLE HARNESS orPLAYER BUS CABLE(Bundle up.)

MUSICLINKHARNESS

FELT-TIPPEN

MARK

30 mm750 mm

CUSHIONTAPE(Cut in quarter.)

30 mm

10. Put a mark with a felt-tip pen on the illustratedlocation of the MusicLink harness.

11. Route the MusicLink harness through thegrommet.

12. Cut one cushion tape in quarters, and wrap the cuttwo cushion tapes to the illustrated location of theMusicLink harness.

GROMMET

CUSHIONTAPE

MUSICLINKHARNESS


5702111B

5513091B

5513082B

DRILLMOTOR

PUSHPIN 3 mmDRILL BIT

RIBRIB

(Middleof ribs.)

80 mm

GLOVEBOX

DRILLBIT

ELECTRICALTAPE

30 mm

19 mm (3/4")HOLE SAW

GLOVEBOX

MUSICLINKHARNESS

19 mmHOLE

MUSICLINKHARNESSDIN CONNECTOR

CUSHIONTAPE

VEHICLEPIPE

13. To prevent damage, wrap electrical tape around thedrill bit at a point about 30 mm away from the tip.While wearing eye protection, drill a 19 mm (3/4")hole through the marked location. Remove all burrsfrom the drilled hole.

14. Route the MusicLink harness DIN connector intothe 19 mm hole in the direction shown, and installthe grommet to the 19 mm hole.

15. Using isopropyl alcohol, clean the vehicle pipewhere the cushion tape will attach. Attach acushion tape to the vehicle pipe.

GROMMET

5426010B

(Align ends.)

UNITCUSHION


16. Insert the MusicLink adapter unit into the unitcushion.


5702151B

5702131B

5702121B

GLOVE BOXOPENING

MUSICLINKHARNESSDIN CONNECTOR(WHITE)

MUSICLINKADAPTERASSEMBLY

MUSICLINKHARNESS


LONG WIRETIE

VEHICLEPIPE

FRONT

VEHICLEPIPE

SIDE VIEWMUSICLINKADAPTERASSEMBLY

BUS CABLEDIN CONNECTOR(BLACK)

(Align the markmade in the step10 with the wiretie.)

MUSICLINK HARNESSand BUS CABLE(Bundle up the excess.)

VEHICLEHARNESS

WIRETIE

17. Route the MusicLink harness and bus cablethrough the glove box opening and connect theMusicLink harness DIN connector (White) and buscable DIN connector (Black) to the MusicLinkadapter assembly. Note the location of theconnectors and the terminals.

18. Secure the MusicLink adapter assembly to thevehicle pipe with two long wire ties.

19. Bundle up the excess MusicLink harness and buscable, and secure them to the vehicle harnesswith the two wire ties (Align the mark made in step10 with the wire tie as shown).

BUS CABLE

VEHICLEHARNESS

GLOVEBOXOPENING

GLOVE BOXOPENING

FRONT


5727020B

5513111B

5513120B

GLOVE BOX

DAMPERARM

COVER

GLOVE BOX

RETAINING TAB

STOPPERS (2)

SCREWS (2)

GLOVE BOX

20. Reinstall the glove box.

5513140B

VEHICLECONNECTOR

CENTERPANEL

VEHICLECONNECTOR

CLIPS (10)

BUS CABLE 14-PINCONNECTOR orBUS CABLE 2 PORT14-PIN CONNECTORCLIPS (2)

VEHICLECONNECTORS (6)

SELF-TAPPINGSCREW AUDIO UNIT

21. Connect the vehicle connectors and bus cable 14-pin connector ( or bus cable 2 port 14-pinconnector ) to the audio unit, and reinstall theaudio unit. Go to step 44.

22. Place the shift lever in the N (Neutral) position.

23. Remove the center panel (ten clips and disconnectthe connectors).


4219041B

5513010B

RETAINING TAB

STOPPERS (2)

SCREWS (2)

GLOVE BOX

NAVIGATION UNITOPENING

BUSCABLE

GLOVE BOXOPENING

DIN CONNECTOR

VEHICLEHARNESS

26. Open the glove box and remove the two stoppersby releasing the two retaining tabs. Remove thetwo screws that fasten the glove box, and removethe glove box.

27. Route the DIN connector end of the bus cable fromthe audio unit opening to the glove box opening.

4722020B

4324021B

GLOVE BOX

DAMPERARM

COVER

GLOVE BOX

CLIPS (2)

BOLTHEAD UNIT

24. Remove the head unit (two bolts, two clips).

25. Remove the damper arm cover and disconnect thearm.


5513021B(Align)BUS CABLE2 PORT 14-PINCONNECTOR

VEHICLE HARNESS(Bundle up the excess.)

BUS CABLE2 PORT

WIRETIE

WIRETIE

VEHICLE20-PINCONNECTOR

VEHICLEHARNESS

BUSCABLE

29. Attach one cushon tape around each bus cable 2port 14-pin connector.

30. Bundle up the vehicle harness, and secure it tothe bus cable and bus cable 2 port with the twowire ties as illustrated, and align the bus cable 2port 14-pin connector with vehicle 20-pinconnector.

5512040B

14-PINCONNECTORS (2)

•Align

CUSHIONTAPES (2)

BUSCABLE

VEHICLE 14-PINCONNECTOR(for XM radio)

BUS CABLE2 PORT

BUS CABLE 14-PINCONNECTOR

28. Connect the bus cable 14-pin connector andvehicle 14-pin connector (for XM radio) to the buscable 2 port 14-pin connectors.

31. At the glove box opening, secure the bus cable tothe vehicle harness with two wire ties.

5727030B

GLOVE BOXOPENING


5702091B

MUSICLINKHARNESS

FELT-TIPPEN

MARK

30 mm750 mm

CUSHIONTAPE(Cut in 4equal parts.)

30 mm

32. Put a mark with a felt-tip pen on the illustratedlocation of the MusicLink harness.

33. Route the MusicLink harness through thegrommet.

34. Cut one cushion tape in 4 equal parts, and wrapthe cut two cushion tapes to the illustratedlocation of the MusicLink harness.

35. To prevent damage, wrap electrical tape aroundthe drill bit at a point about 30 mm away from thetip. While wearing eye protection, drill a 19 mm(3/4") hole through the marked location. Removeall barrs from the drilled hole.

GROMMET

CUSHIONTAPE

MUSICLINKHARNESS

5513082B

DRILLMOTOR

PUSHPIN 3 mmDRILL BIT

RIBRIB

(Middleof ribs.)

80 mm

GLOVEBOX

DRILLBIT

ELECTRICALTAPE

30 mm

19 mm (3/4")HOLE SAW

5513091B

GLOVEBOX

MUSICLINKHARNESS

19 mmHOLE

MUSICLINKHARNESSDIN CONNECTOR

36. Route the MusicLink harness DIN connector intothe 19 mm hole in the direction shown, and installthe grommet to the 19 mm hole.

GROMMET

5702111B

CUSHIONTAPE

VEHICLEPIPE

37. Using isopropyl alcohol, clean the vehicle pipewhere the cushion tape will attach. Attach acushion tape to the vehicle pipe.


5426010B

(Align ends.)

UNITCUSHION

MUSICLINK ADAPTERUNIT

38. Insert the MusicLink adapter unit into the unitcushion.

5702121B

GLOVE BOXOPENING

MUSICLINKHARNESSDIN CONNECTOR(WHITE)


MUSICLINKHARNESS

BUS CABLEDIN CONNECTOR(BLACK)

39. Route the MusicLink harness and bus cablethrough the glove box opening and connect theMusicLink harness DIN connector (White) and buscable DIN connector (Black) to the MusicLinkadapter assembly. Note the location of theconnectors and the terminals.

BUS CABLE

5702151B

5702131BMUSICLINKADAPTERASSEMBLY

LONG WIRETIE

VEHICLEPIPE

FRONT

VEHICLEPIPE

SIDE VIEWMUSICLINKADAPTERASSEMBLY

(Align the markscribed in thestep 32 with thewire tie.)

MUSICLINK HARNESSand BUS CABLE(Bundle up the excess.)

VEHICLEHARNESS

WIRETIE

40. Secure the MusicLink adapter assembly to thevehicle pipe with two long wire ties.

41. Bundle up the excess MusicLink harness and buscable, and secure them to the vehicle harnesswith the two wire ties (Align the mark scribed inthe step 32 with the wire tie as shown).

VEHICLEHARNESS

GLOVEBOXOPENING

GLOVE BOXOPENING

FRONT


5513111B

5513130B

CLIPS (2)

BOLTHEAD UNIT

BUS CABLE 14-PINCONNECTOR orBUS CABLE 2 PORT14-PIN CONNECTOR

5513120B

GLOVE BOX

DAMPERARM

COVER

GLOVE BOX

RETAINING TAB

STOPPERS (2)

SCREWS (2)

GLOVE BOX

42. Reinstall the glove box. 43. Connect the vehicle connectors and bus cable 14-pin connector ( or bus cable 2 port 14-pinconnector ) to the navigation unit, and reinstall thenavigation unit.

44. Check that all wire harnesses are routed properlyand all connectors are plugged in.

45. Reconnect the negative cable to the battery.

46. Enter the customer’s radio anti-theft code, andreset the radio station presets, the clock.

47. Reinstall all removed parts.

48. Turn the power of the audio unit ON. Check that"No Disc" is shown on the display while in the CDchanger mode (recognized as CD changer 4).

NOTE: Whenever the battery is disconnected, thedriver’s AUTO function is disable.

49. Start the engine. Push down on the driver’swindow switch until the window is fully open.

50. Pull up on the driver’s window switch fully to closethe window completely, then hold the switch for2 seconds or more.

51. Test the window AUTO function.

installation honda musiclink™ 2007 odyssey …

Documents