(J) M6*30 Screw (x4)(K) M6*15 Screw (x4)

(F) M4*30 Screw (x4)

TV

(G) M4*15 Screw (x4)

AEON-50201Installation Instructions

Important Notes Installation will require a minimum of two people. Under no circumstances should this be attempted by one person.We highly recommend this product be installed by a qualified professional.Please do not begin installation until you have thoroughly read and understood these instructions. The AEON-50201 Articulating Wall Mount supports flat panel displays from 32” to 60” and supports a maximum load of 50.0 kgs (80 lbs).Ensure the wall you plan to use will safely support four times the combined weight of the Articulating Wall Mount and your chosen display.Under no circumstances should this product be mounted to metal studs.The manufacturer does not accept responsibility for incorrect installation.

•

•

•

•

•

•

•

Adaptor Brackets(x2)

Component Checklist

LEVEL ADJUSTIf your TV is perfectly level when arm is extended, you can skip this step. To make horizontal level adjust-ments, loosen two bolts with oval slots at the back of arm assembly shown in Fig 10. Make the necessary level adjustments to your tv. Now tighten two bolts to insure to maintain a perfectly level TV.

A. Tilt Adjustment B. Horizontal Adjustment

Adjust Horizontal Level & Tilt

Cable Management

(T)25*25 Shim(x4)

A

TV Plate (x1)B CD

(I) M5*15 Screw (x4) (M) M8*15 Screw(x4)(H) M5*30 Screw (x4) (L) M8*30 Screw (x4)

(S) Plastic Sleeve(x4)

(E) Lag Bolt ST6.3x50mm (x4)

(O) Spanner S=13(x1) (P) M8*16 Screw(x4)

Wall Mount (x1)

NOTE: 4 TV Mounting Screws are Needed for Installation.Keep Additional Screws for Future Use.

(R) M8 Locknut (x8)(Q) Ø8 Washer (x4)(N) Inner Hexagon Spanner S=5(x1)

Tighten 2 Screws

The AEON - 50201 includes a cable management system where cable can be routed along the length of the arm assembly. Fig.8

With all cables in place, push the display in and out to be certain that the arm assembly moves freely, without stretching or damaging the cables.

Step 10

Step 11

fig. 9 fig. 10

fig. 9

TOOLSREQUIRED

PhillipsScrewdriver

Ratcheting Wrench Drill

(Cross Reference)

High Voltage110V Low AV

Voltage

p.4

fig. 8

Features :▪ Ideal for 32”-60“ flat panel displays▪ VESA Compliant: 100x100mm to 400x400mm▪ 80lbs (50kg) max weight capacity▪ Provides optimum viewing angles▪ Offers 180 of swivel on wall( 90 degrees each way)▪ Low profile design: folds against the wall▪ Level adjust ±6° and +15°/-15° of tilt▪ Extends 19.4”(495mm) from the wall;▪ Retracts flush to the wall▪ Integrated cable management▪ Includes hardware for installation to wood studs or concrete wall.

G1

G2

14.5”

13”

Determine where you want your TV mounted on your wood stud wall. Note that the center of the metal in wall box (A) of this TV mount will represent the center of your TV. Choose the appropriate height for your viewing pleasure. The location you choose must be between two 16 inch on center wood studs.

Step 1 Now that you have chosen an area. Mark out an area 14.5 inches wide and 13 inches tall. Note again the center of this area will be the center of your TV . Make sure that the vertical edge lines are located on the inside edge of your wood studs. Fig.1

Step 2 Cut out the drywall in the marked area with the appropriate tools . Fig.1

Step 3 Insert the metal in wall box (A) into opening. While pushing the box against the right stud, mark the location of all holes G1,G2, G3 and G4. Remove in wall metal box.

Step 4 Pre drill the four marked locations G1 through G4 with a 3/16 inch drill bit.

Step 5 Insert Metal in wall box (A) into opening. Arm should be attached to metal box on the left side. Take four lag screws (E) from Bits Bag. Using a ratcheting wrench tighten screws G1 through G4. Shown in Fig 2.

Refer to the TV mounting screws cross reference guide on page 1 to determine the diameter and length of the screws needed to match the size and depth of the holes on your TV.

Step 6 Determine your Vesa size (in mm) fig. 4. If Vesa size is100x100, 100x200, 200x100 or 200x 200 go to step 8. If your Vesa pattern is 300x200, 300x300, 400x200, 400x300 or 400x 400, go to step 7. NOTE: You Will Not Need Two Adaptor Brackets (D).

Step 7 Attach the two extension wings (Dx2) to the TV wall plate (B) location. Using four bolts (P), washers (Q), locknuts (R) and spanner tool (O) attach the two extension wings on the TV plate tightly. See Fig 5.

Step 8 Align TV plate to your TV (Make sure “TOP” is up on TV plate). Screw 4 selected bolts into the thread holes on the TV back, through a washer (T) and the corresponding holes on the TV plate(Fig 4). Some TV’s may require the use of spacers (S).Spacers are placed between the TV and the TV plate. See Fig. 6. Step 9 Attach two nuts (R) to the top 2 permanent bolts on back of TV plate (B). Use Spanner (O). Do not tighten all the way yet. Leave about 1/4” space between nut and TV plate. Slide 2 bolts onto U shaped slots on top of the arm extension (C). Secure 2 more locknuts (R) to the bottom bolts and tighten all 4 locknuts (R) down securely. See Fig 7

Mounting Your TV Installation Wall Mount to In-Wall Box

Right Adaptor Bracket

Left Adaptor Bracket

F/G/H/I/J/K/L/M

S

TV

TINSTALLATION

G3

G4

CAUTION: DO NOT TIGHTEN SCREWS WITH IMPACT DRILL OR HAMMER.HAND TIGHTEN TO NOT CAUSE DAMAGE TO WOOD STUD AND OR LAG SCREW.

fig. 5

fig. 6

Socket Pan Head ScrewM8*15mm (P)

Metal Washer8mm (Q)Ø

fig. 3

fig. 7

Wood Stud Wall

Wood Stud Wall

p.2p.3

For TV’s with Recessed Holes

400mm = 153/4 in300mm = 1113/16 in200mm = 77/8 in100mm = 315/16 in

1 2 3 4 5 6 7 8 9 10

400mm

300mm

200mm

100mm

NOTE: To ensure successful installation match correct TV VESA pattern with whole pattern on adapter plate.

TOP

TOP

TOP

fig. 4

NOTE: Use the punchouts to run Low voltage wires like HDMI and other audio/video cables as well as high voltage into a 1-Gang Old Work Electrical Box.

A

D

B

Q

P

R

Punch out appropriate box or boxes for your application.