installation instructions for klinger gaskets- einbau_e

8/4/2019 Installation Instructions for KLINGER Gaskets- Einbau_e

1/6

1. Gasket dimensions

2. Storage3. Handling4. Bolts/ Nuts/ Washers

5. Gasket installation

KLINGER The global leader in static sealing

Installation

instructions forKLINGERgaskets


2/6

Installationinstructions for

KLINGER gaskets

The gasket has to have the correctsize.

1. Gasket dimensions

Cut the bolt holes just a bit largerthan the bolts to simplify thecentralization of the gasket.

The inner diameter of the gasketshould not be smaller than the innerdiameter of the flange.

The gasket should be stored

horizontal to avoid tensions andpermanent warpage. Ideal storage conditions are: temperature < 25C air humidity 50 - 60% Darkened storage roomStore the gasket in a clean condition(ideally in a plastic bag).

All types of gaskets (metallic gas-kets, PTFE gaskets, fibre reinforcedgaskets etc.) should be handled withthe same care and attention. Avoid carrying small gaskets in apocket to protect the gasket fromdamage.

Do not bend the gasket and do notdamage the surface.

Carry ready cutted gasketscarefully, ideally in some form ofprotective cover.

Correct size

Bolt holes

Inner diameter Protect the gasket

Protect the surface

3. Handling

Ideal storage conditions

2. Storage


3/6


KLINGER gaskets

Pay attention that all bolts whichare designed for the flange areinstalled. Check if the used bolts are suitablefor the given operating temperatures. Tighten the bolts cross-wise withthe correct torque (calculation withKLINGERexpert 5.1). Ensure that there is no corrosionon the bolts because this can effectthe function of the bolt. Never Re-use bolts.

Bolt properties

Use a nut which has a specifiedproof load 20% greater than theultimate strength of the fastener. Use standard threads, rather thanfine. Use the correct lubricant.

Nut properties

Use the same material for thewashers and the nuts. Use washers to: bridge slotted or oversized holes even interface forces between jointcomponets reduce problems of fatigue byspreading the load placed by thefastener on the joint.

Washers

At first make sure that thefollowing tools are available and ingood condition: the correct gasket chosen for thespecific application a calibrated torque wrench a wire brush lubricants for the bolts.

The tools

Make sure that the flange surfacesare clean. Check the bolts and the flangesurface if they are technically ok andfree from any seriuos defects. Always brush in the direction ofthe grooves. To avoid damage on the flangesurface please use a brass drift.

Cleaning of all flange surfaces

Make sure that the flanges areparallel and report all irregularities.

Flange conditions

Insert the gasket carefully betweenthe flanges. The gasket has to be centralized inthe flange. Ensure that the gasket is installedin a dry state. It is important that the gasket isnot pinched or otherwise damagedwhen bringing the flanges together.

Important for the gasket4. Bolts/Nuts/Washers 5. Gasket installation


4/6


KLINGER gaskets

5. Gasket installation

Apply lubricant to the bolt and thenut threads as well as to the face ofthe nut to reduce friction whentightening Pay attention that the lubricantdoes not contaminate the gasket orthe flange surfaces. The recommended servicetemperature of the lubricant has to bewithin the process servicetemperature limits.

The required torque value can becalculated with KLINGERexpert 5.1. Make at least 4 stages to therequired torque as follows: finger tighten bolts use 30% of the required torque use 60% of the required torque use the full torque Close the torquing with one finalpass in a clockwise sequence.

For safety reasons never re-use agasket. The cost of a gasket is minimalcompared with the costs which willcome into being of a down time of theplant.

If retightening is considerednecesary, this should only be done atambient temperatures before orduring the first start-up. Never retighten compressed fibregaskets at higher operating tempera-tures and longer operating times.

Re-Tightening

Lubrication of bolts Bolt tightening Re-use of gaskets


5/6

KLINGERexpert 5.1Powerful Sealing

Calculation

Features: Easy, self-explaining flange

selection

Graphical analysis ofgasket stresses QuickHelp Function Product documentation of

the sealing materialsincluded on the CD

Step by Step selection tothe most suitable gasketmaterial

Solution proposal of theprogram at calculationproblems

available in many different

languages


6/6

We have deviseda tried and tested method,

to guide you step by step to the right gasketfor your needs.

1. Applications overview:

The gasket characteristics comparedwith the criteria to be met in typicalapplication.

2. Product documentation:A separate data sheet is supplied foreach gasket in our range.The pT diagrams are an invaluableaid to selecting the gasket mostsuitable for a particular application.

3. Data on chemical resistance:

This section indicates the resistanceof the individual Klinger gaskets toover 200 chemicals in common use.

4. Technical information by Fax:Let us have the details of yourparticular gasket requirements and

you will receive a prompt reply, insome cases within 24 hours.

5. Sealing calculationson your PC:For the experienced specialist wehave developed a powerful programwhich will answer all your questionson gasket construction, design andmaintenance. We supply the softwarewith on-line help.

6. Ideally you should run yourown tests:We will supply the materials youneed to carry out tests under yourown operating conditions.

7. On-sit advice:With particularly difficult problemswe shall be glad to advice youon-site. We can supply productsadapted from our existing range orcustom-formulated products.

Rich. Klinger DichtungstechnikGmbH & Co KG

Am Kanal 8-10A-2352 Gumpoldskirchen, AustriaTel ++43 (0) 2252/62599-137Fax ++43 (0) 2252/62599-296e-mail: [email protected]://www.klinger.co.at

Subject to technical alterations.Issue: March 2006

Certified according toDIN EN ISO 9001:2000

Powerful sealing calculation withonline help on CD-ROM

installation instructions for klinger gaskets- einbau_e

Documents