installation instructions - accessorybase.mazda.ph-wt.com · installation instructions vehicle:...
TRANSCRIPT
Common-1
iPod INTEGRATION MODULE
INSTALLATION INSTRUCTIONS
Vehicle: Mazda2, Mazda3, Mazda5, Mazda6, Mazda RX-8 Mazda MX-5, Mazda CX-7, Mazda BT-50, New Mazda2, New Mazda6
Parts number:C9F2 V6 572 EU Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the iPod integration module. Your safety depends on it. Keep these instructions with your vehicle records for future reference. Note:
There are several WARNING and CAUTION sections in this booklet concerning safety when installing or removing the iPod integration module. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle. WARNING: Indicates a situation in which serious injury or death could result if the
warning is ignored. CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could
result if the caution is ignored.
Do not modify the iPod integration module. Do not install the iPod integration module in any way other than described in the following
instructions. If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent
errors in installation. If you have any questions about the use of the accessory, ask your Mazda dealer for proper
advice before using it. Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons
and property that arise from the failure of the dealer or installer to follow these instructions. To ensure safety and reliability of the work, installation, removal and disposal work by an
Authorized Mazda Dealership is recommended. Be careful not to lose removed parts, and be sure that they are kept free from scratches,
grease or other dirt.
* iPod is a trademark of Apple Computer, Inc., registered in the United States and other countries.
To the dealer Please turn over these instructions to the customer after installation.
To the customer Keep these instructions after installation. The instructions may be necessary for installing other
optional parts or removal of this accessory. Should the vehicle or this accessory be resold, always leave these instructions with it for the next
owner.
GE
1ED6P11A13300
Common-2
PARTS LIST
iPod integration module (Part No. C9F2 V6 572 EU)
Parts Part Name Qty Parts Part Name Qty Parts Part Name Qty
iPod Integration module
1
Harness (c) 1
iPod connection cable
1
Tie wrap Large 300 mm Small 100 mm
L 7 S 10
Double-sided adhesive tape (44×118mm)
2
Pad protector (50×100 mm)
10
※ A separately purchased "Selector box" (TD13 79 CFZ) is necessary when installing the iPod integration module to vehicles equipped with an AUX terminal.
☆Flathead screwdriver ☆Socket wrench ☆Pliers ☆Soft cloth ☆Phillips screwdriver ☆Cutter knife ☆Scissors ☆Vinyl tape ☆Fastener remover ☆Mat
2. REQUIRED TOOLS
• Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage.
NOTE:
1. PARTS
3. BEFORE INSTALLATION
• To prevent short related accidents while performing procedures, disconnect the negative battery cable before beginning any work.
• When disconnecting the connector, hold the connector itself to remove while pressing the connector lock. • Do not apply excessive force to the wiring harness as it could cause an open circuit. • When locking connectors, listen for a click that will indicate they are securely locked. • Be careful not to pinch the wiring harness. Otherwise, the wiring harness could be damaged. • When removing and installing vehicle parts, make sure they are clean with no scratches. Also, be sure to
cover the vehicle body with protectors or mats when removing/installing parts to prevent scratches and dirt.
CAUTION
• Refer to the applicable Workshop Manual for removal and installation of vehicle parts. Not following the procedures for removal/installation in the Workshop Manual could result in an accident or vehicle malfunction.
• When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory.
NOTE:
Common-3
Installation of iPod integration module only <For vehicles without AUX terminal>
iPod (On-market product )Audio unit
iPod integration module
Harness (c)
iPod connection cable
16-pin connector
4. CONNECTION DIAGRAM
Common-4
iPod integration module and selector box installation <For vehicles equipped with an AUX terminal>
5. CAUTIONS ON CONNECTION
iPod (On-market product)
iPod integration module
iPod connection cable
Audio unit
Selector Box Harness (a)
Harness (b)
Harness (c)
AUX
16-pin connector
When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle.
CAUTION
■ Installation instructions (For Mazda2 only)
Mazda2-1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Column cover removal (upper and lower) 1. Remove the ignition key knob.
(Vehicles with advanced keyless system only) 2. Pull the upper column cover upward and remove it. 3. Remove the bolts (2) and screw (1), then remove the
lower column cover. Lower panel removal 1. Pull the lower panel down and outward and disengage hooks
A (2 locations). 2. Pull the lower panel downward at an angle of 20 degrees from
the horizontal and disengage clips B (2 locations). Console removal 1. Insert a flathead screwdriver wrapped with protective tape into
notch A in the cover and disengage hooks B. 2. Disengage hooks C while lifting up the cover in the direction of
the arrow. 3. Remove the shift knob. (MTX vehicles only) 4. Remove the screws and fasteners, then remove the console.
Column cover (upper)
Bolt Screw
Column cover (lower)
Vehicle front
IG key knob
Column cover (lower)
Lower panel
Clip B
Hook A Vehicle front
Console
A
Vehicle front
Cover Hook
Fastener Screw
Hook C
Hook B
ABB
B BC
C
Shift knob
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a right-hand drive vehicle, however, the procedure is the same for the left-hand drive vehicle.
NOTE
■ Installation instructions (For Mazda2 only)
Mazda2-2
Center panel module removal 1. Remove the knobs (3). (Vehicles with manual A/C only) 2. Remove the screws (2). (Vehicles with manual A/C only) 3. Remove the bolt (1) shown in the figure. 4. Remove the ashtray. 5. Pull the center panel outward from part A and
disengage clips B (8 locations). 6. Disconnect the connector and the antenna plug, then
remove the center panel module.
Glove box No. 1 removal 1. Remove the fasteners (3). 2. Pull glove box No. 1 outward, disengage the clips (3
locations) from the instrument panel, then remove it. Glove box No. 2 removal 1. Move the stopper inward and remove. 2. Pull down glove box No. 2, disengage the clips (2 locations)
from the instrument panel, then remove it.
Clip x 3
Fastener x 3 Glove box No. 1
Vehicle front
Clip
Clip
Stopper
Center panel module Connector
Clip B
Bolt
B
Center panel module clip position Sectional
view B
B
B
B B
B
B
Screw
Ashtray
Knob A
Antenna plug
Vehicle front
■ Installation instructions (For Mazda2 only)
Mazda2-3
WIRING <Installation of iPod connection adapter only>
iPod connection cable
○B
○A
Vehicle front
Pad protector Vehicle front
Harness (c)(To audio unit)
(Route harness so that this part is approx. 170 mm)
○C
○A
Put iPod connection cable in glove box (Cable 30 cm from instrument panel)
Fit connector cover when iPod is not connected
○B
Vehicle front
Harness (c)(To audio unit)
iPod connection adapter
Loop redundant part of cable and tie it in two locations, then secure with pad protectors
iPod connection cable
iPod connection
adapter
Double-sided adhesive tape
(Cut and affix) Pad protector
Pad protector (Affix to member edges)
Pad protector
Vehicle front
Pad protector(Cut and affix)
Tie wrap(small)
○C
iPodconnection
adapter
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod connection adapter, be sure to route cablesavoiding sharp edges and burrs on the vehicle's sheet metal. To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is to be
adhered. After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with
other parts causing failure or noise.
CAUTION
Approx. 170 mm
Pad protector
■ Installation instructions (For Mazda2 only)
Mazda2-4
1. Reconnect the negative battery cable.
3. CONNECTION CHECK
Connect the negative battery cable carefully so that it does not interfere with other parts. If the battery is disconnected, the automatic full open/close feature of the power window is disabled.
This function can be reactivated using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is fully
closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
CAUTION
■ Installation instructions (For Mazda3 only)
Mazda3-1
Negative battery terminal disconnection 1. Disengage tabs A (2 locations) and lift up the front of the battery
cover. 2. Pull the battery cover towards the front, remove pins B (2
locations), then remove the battery cover. 3. Disconnect the negative battery cable and wrap its terminal with
tape to insulate it.
Decoration panel removal 1. Open the glove box, pull the decoration panel outward in the
order shown (1 to 5), disengage clip A (1 location) and tab B (1 location), then remove the decoration panel.
Battery (-) terminal
Tab A
Pin B
Vehicle front
Vehicle front
Battery cover
Vehicle front
Clip A
Decoration panel
Tab B
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a right-hand drive vehicle, however, the procedure is the same for left-hand drive vehicle.
NOTE
■ Installation instructions (For Mazda3 only)
Mazda3-2
Glove box removal 1. Remove the screws (2). 2. Pull the glove box outward, disengage clips A (8 locations)
and tab B (1 location), then detach the glove box. 3. Remove the glove box light socket, then remove the glove box. Center panel module removal 1. Remove the screws (2). 2. Pull the center panel module outward from the direction of
arrows ① and disengage clips A (2 locations). 3. Disconnect the connector and the antenna feeder, then
remove the center panel module.
Screw
Center panel module
Connector
Antenna feeder
① ①
①
A A
Clip A
Pull bracket
Vehicle front
Glove box light socket
Glove box Clip A
Screw Tab B
■ Installation instructions (For Mazda3 only)
Mazda3-3
Glove box drilling (Excluding vehicles with car navigation system) 1. Remove the screw (1) and remove the cover. 2. Put a mark on the glove box in the position shown in the figure. 3. Mark the drilling position and drill a hole using a φ10 hand drill. 4. Cut off the shaded part ( ) with a cutter knife and remove
burrs with a hand file. iPod integration module installation 1. Cut the double-sided adhesive tape (1 pc.) to 44 x 80 mm and
adhere it to the iPod integration module. 2. Cut the pad protector to 50 x 50 mm (half) and adhere it to the
iPod integration module. 3. Adhere the remaining half pad protector to the vehicle (below
glove box installation position) as shown in the figure. 4. Peel the backing of the double-sided adhesive tape (1 pc.) and
attach the iPod integration module to the vehicle. 5. Secure the iPod integration module with a tie wrap (large).
Pad protector 50×50 mm
iPod integration module
Double-sided adhesive tape 44×80 mm
Be careful when handling drills and other sharp objects. If not handled properly, it could result in serious injury.
WARNING
The glove box is made of soft material. Drill it slowly and carefully.
CAUTION
5 mm
φ10 mm
<Glove box top view>
Half
Half
Vehicle front
iPod integration module
Tie wrap (large)
iPod integration module
Pad protector
50 mm
2. INSTALLATION AND WIRING
• To ensure proper adhesion, be sure to degrease the area where the tape is to be adhered.
CAUTION
Make sure to remove burrs from both the surfaces so that they are flat and smooth.
CAUTION
■ Installation instructions (For Mazda3 only)
Mazda3-4
WIRING <Installation of iPod integration module only> (For vehicles without AUX terminal)
○C Vehicle front
Put iPod connection cable in glove box(Cable 30 cm from instrument panel)
Tie wrap (large)
○A
○B
Vehicle front
Tie redundant part
Tie wrap (small)
Tie wrap (large)
Vehicle front ○B
Harness (c) (To audio unit)
(Route harness so that this part is approx. 170 mm)
Approx. 170mm
○A
Pad protector
iPod connection cable
○C To inside of glove box
iPod connection cable
iPod integration module
Tie redundant part
Harness (c)
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing malfunction or noise.
CAUTION
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
Secure to vehicle wiring harness with tie wrap (large)
■ Installation instructions (For Mazda3 only)
Mazda3-5
<Installation of iPod integration module and selector box> (For vehicles with AUX terminal)
Selector box installation 1. Wrap a tie wrap (large) to the selector box as shown in figure. 2. Peel the backing off the pad protectors (2) and affix the
protectors on top of the tie wrap (large). 3. Affix the selector box to the vehicle harness under the heater
duct as shown in the figure.
• To ensure proper adhesion, be sure to degrease the area where the tape is to be adhered.
CAUTION
Pad protector Tie wrap (large)
100 mm
Pad protector
Selector box
30 mm
Tie wrap (large)
Vehicle harness
Selector box
Selector box
Vehicle front
Vehicle front
iPod integration module
■ Installation instructions (For Mazda3 only)
Mazda3-6
WIRING <Installation of iPod integration module and selector box> (For vehicles with AUX terminal)
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing malfunction or noise.
CAUTION
Selector box
iPod integration module
Harness (a)(To audio unit)
Harness (b)(To AUX terminal)
Vehicle harness
Harness (a) (Connect to audio unit)
Vehicle front
○A
AUX connector(16P)
Harness(b)
(Route harness so that this part is approx. 170 mm)
Approx. 170mm
Press the cable into theback and secure cable
iPod integration module
Selector box
○ATo AUXterminal
Vehicle front
○C
Vehicle front Put iPod connection cable in glove box(Cable 30 cm from instrument panel)
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
Pad protector(Attach to edge)
Tie redundant part
Tie wrap (small)
○A To audio unit
Selector box
Vehicle front
iPod integration module
Tie wrap (large)
○C
■ Installation instructions (For Mazda3 only)
Mazda3-7
1. Reconnect the negative battery cable.
3. CONNECTION CHECK
Connect the negative battery cable carefully so that it does not interfere with other parts. If the battery is disconnected, the automatic full open/close feature of the power window is disabled.
This function can be reactivated using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds
after it is fully closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda
Dealer.
CAUTION
■ Installation instructions (For Mazda5 only)
Mazda5 -1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Side wall (driver's side and passenger's side) removal 1. Disengage clips A (3 locations). 2. Disengage the tab and remove the side wall. Front console removal 1. Remove the shift knob. 2. Lift the shift panel, disengage the clips, and then remove the
shift panel from the front console. 3. Remove the screws (4). 4. Pull the front console outward and disengage clips A and tabs
B. 5. Disconnect the cigarette lighter connector and remove the
front console.
Clip A
Shift panel
A
A
A
A
Shift knob
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
Side wall A
Clip A
A
A
Handle with care as it can break easily
Screw
Front console
Screw
Clip A Tab B
B A
A
B
A B B B B
A A
A
Screw
A
The procedure described here is for a right-hand drive vehicle, however, perform work in the same manner for a left-hand drive vehicle as well.
NOTE
1ED6P11A13400
GE
■ Installation instructions (For Mazda5 only)
Mazda5 -2
Center panel removal 1. Remove the screws (2). 2. Pull the center panel outward and disengage clips A (5
locations). 3. Disconnect the connector and the antenna feeder, then remove
the center panel. Glove box removal 1. Push the stay damper in the direction of the arrow and
disengage the glove box lid from the stay damper.
2. Push down the stopper to disengage. 3. Pull the glove box lid outward while keeping it lowered as
shown in the figure, disengage the clip, and then remove the glove box lid.
4. Remove the screws (5). 5. Pull the glove box outward and disengage clips A (5 locations).
Stopper
Stay damper
Clip
Glove box
Glove box lid
Screw Screw
Clip A
A
A
A
A
A
Vehicle front
Clip A A
Screw
AA
A
A
Connector Antenna feeder
■ Installation instructions (For Mazda5 only)
Mazda5 -3
WIRING <Installation of iPod integration module> For RIGHT hand drive vehicle
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs of the vehicle's sheet metal.
To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is affixed.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing failure or noise.
CAUTION
iPod integration module
Loop redundant part of cable and tie it in two locations, then secure with pad protectors
Harness (c)iPod connection cable
Vehicle front
Put iPod connection cable in glove box (Cable 30 cm from instrument panel)
○A
Vehicle front
Harness (c) (To audio unit)
(Route harness so that this part is approx. 170 mm)
Approx. 170 mm
Tie wrap (small)
Vehicle front
Pad protector
○A
○B ○C
○B
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
Double-sided adhesive tape (1 pc.)
Pad protector Tie redundant part
Vehicle front
iPod integration module (Align to pad protector)
(Affix cut part to iPod integration module and remaining part to body)Pad protector
Affix 5 mm lower from body edge
5 mm
Tie wrap (small)
Pad protector
Pad protector(Affix from member backside to protect harness)
○C
■ Installation instructions (For Mazda5 only)
Mazda5 -4
WIRING <Installation of iPod integration module> For LEFT hand drive vehicle
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs of the vehicle's sheet metal.
To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is affixed.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing failure or noise.
CAUTION
iPod integration module
Loop redundant part of cable and secure with pad protectors
Harness (c)iPod connection cable
○A
Vehicle front
Harness (c) (To audio unit)
(Route harness so that this part is approx. 170 mm)
Approx. 170 mm
Tie wrap (small)
Vehicle front
Pad protector
○A
○B ○C
Vehicle front
Put iPod connection cable in glove box(Cable 30 cm from instrument panel)
○B
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
Double-sided adhesive tape (1 pc.)
Pad protector
Loop redundant part
Vehicle front
iPod integration module Pad protector
○C
■ Installation instructions (For Mazda5 only)
Mazda5 -5
1. Reconnect the negative battery cable.
3. CONNECTION CHECK
Connect the negative battery cable carefully so that it does not interfere with other parts. If the battery is disconnected, the automatic full open/close feature of the power window is disabled.
This feature can be recovered by the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is fully
closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
CAUTION
■ Installation instructions (For Mazda6 only)
Mazda6-1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Parking brake panel removal 1. Remove the parking brake panel clips (9 locations) using a
tape-wrapped flathead screwdriver, and remove the parking brake panel.
Shift panel removal 1. Remove the shift panel clips (4 locations). 2. Disconnect the ashtray lamp and connector, and remove the
shift panel.
Glove compartment removal 1. Remove the damper. 2. Disengage the glove compartment stoppers from the dashboard
by pushing each one inward. 3. Pull the glove compartment down and outwards to disengage
the hooks, and then remove it.
Stopper
Hook
Glove compartment
Damper
Vehicle front
• For vehicles with a DVD navigation system, disconnect theconnector for the navigation system removal
NOTE:
Clip (4 Locations)
Connector Lamp
Shift panel
Connector (For navigation remote control )
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a right-hand drive vehicle, however, the procedure is the same for left-hand drive vehicle.
NOTE
Clip
Parking brake Panel
(9 Locations)
■ Installation instructions (For Mazda6 only)
Mazda6-2
DVD navigation unit removal (vehicles with navigation system only ) 1. Remove the bolts (2 locations). 2. Disengage the navigation unit tab, and disconnect the
connector. 3. Remove the DVD navigation unit.
Connector
DVD navigation unit Tab (1 Location)
Bolt (2 Location)
■ Installation instructions (For Mazda6 only)
Mazda6-3
Center lower panel removal 1. Remove the bolt indicated in the figure. 2. Remove the air conditioner knobs (3 locations), then remove the screws (2 locations). (Vehicles with a manual
air conditioner) 3. Remove the screws (2 locations) on the lower part of the center lower panel, and detach the center lower panel
clips (6 locations). 4. Disconnect the connectors (audio unit connector and antenna feeder), detach the vehicle wiring harness
connector clip from the bracket, then remove the center lower panel.
Center lower panel
Bolt (1 Location)With manual air conditioner
Air conditioner knob(3 Locations)
Screw (2 Locations)
Audio unit connector
With automatic air conditioner
Screw (2 Locations)
Center lower panel
Center lower panel
Screw (2 Locations)
Vehicle wiringharness connector
Clip
Antenna feeder
Vehicle wiring harness connector
Clip (6 Locations)
Antenna feeder
Bracket
Bracket
Clip (6 Locations)
Audio unit connector
Vehicle wiringharness connector
Clip
Vehicle wiring harness connector
■ Installation instructions (For Mazda6 only)
Mazda6-4
WIRING <Installation of iPod connection adapter only>
Harness (c) (To audio unit)
iPod connection cable
iPod connection adapter
Tie redundant part(Tie using 2 straps (small) and secure with pad protectors in two locations)
To iPod connection adapter
Put iPod connection cablein glove box (Cable 30 cmfrom instrument panel)
Vehicle front
Pad protector
Tie wrap (large)
Pad protector (Secure iPod con. cable to iPod con. adapter)
iPod connection adapter
Align corners
iPod connection adapter
Double-sided adhesive tape
<Installation position enlarged view>
15mm
Vehicle front
Harness (c) (To audio unit)
Pad protector
Pad protector(Attach to edge)
Approx. 170 mm
(Route harness so that this part is approx. 170 mm)
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod connection adapter, be sure to route cablesavoiding sharp edges and burrs on the vehicle's sheet metal. To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to
be adhered. After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with
other parts causing malfunction or noise.
CAUTION
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
■ Installation instructions (For Mazda6 only)
Mazda6-5
1. Reconnect the negative battery cable.
3. CONNECTION CHECK
Connect the negative battery cable carefully so that it does not interfere with other parts. If the battery is disconnected, the automatic full open/close feature of the power windows is disabled.
This feature can be reactivated using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is fully
closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
CAUTION
■ Installation instructions (For MX-5 only)
MX-5 -1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Scuff plate (passenger’s side) removal 1. Pull the scuff plate upward while detaching tabs C, and then
detach clips A (4), pins B (4), and D (1) from the body, and remove the scuff plate.
Side trim (passenger's side) removal 1. Remove the seaming welt. 2. Remove the fastener (1). 3. Pull the side trim toward you, detach clip A (1 location)
and pin B (1 location), and then remove the side trim.
Clip A
Fastener
A B
Pin B
Vehicle front Seaming welt
Side trim
1. VEHICLE PARTS REMOVAL
Scuff plate
Pin D
Pin C
Tab C
Clip A
Vehicle front
AA
A
AB
B
B
B
C
C
D
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a right-hand drive vehicle, however, perform work in the same manner for a left-hand drive vehicle as well.
NOTE
1ED6P11A08400
■ Installation instructions (For MX-5 only)
MX-5 -2
Lower panel removal 1. Pull the top side of the lower panel outward, and then
remove clips A (2 locations) and tab B (1 location). 2. Remove tabs C (2 locations), then remove the lower panel. 3. Remove the screws (4), then remove the knee bolster.
(If equipped)
Side wall removal 1. Pull the side wall outward, detach clips A (2 locations), clips
B (4 locations), the pin C (1 location), and tab D (1 location), and then remove the side wall.
Center panel module removal 1. Shift a shift lever to the R position or a selector lever to the D
range. 2. Remove the bolt (1 location). 3. Remove the screws (2 locations). 4. Pull the center panel module outward, then remove clips
A (4 locations). 5. Remove the air conditioner side connector. 6. Pull the center panel module further outward and cut off
the tape binding the antenna and vehicle side wiring harness.
7. Remove the audio side connectors (2 locations), the antenna
feeder (1 location), and then remove the center panel module.
Pin C
A
C
B
Side wall
Clips B
Tab D
A
B
B
D B
Clips A
Tab B
A A
C
B
C
Lower panel
Clips A
Tabs C
Screws
Knee bolster
(2 Locations) Screws (2 Locations)
Antenna feeder
A
Screw
A
A A
Clips A
Center panel module
Screw
Bolt Audio side connectors
Air conditioner side connector
Do not apply excessive force when pulling out the centerpanel; otherwise it could cause an open circuit.
CAUTION
■ Installation instructions (For MX-5 only)
MX-5 -3
Glove compartment lid removal 1. Open the glove compartment lid and remove the damper pin. 2. Push the glove compartment lid inward and disengage the
stoppers (2 locations). 3. Pull the glove compartment lid outward, detach the clips (2
locations), and then remove the glove compartment lid. Foot support (passenger's side, front) removal 1. Partially peel back the passenger's-side front floor mat. 2. Disconnect the connector and remove the foot support
from the vehicle.
Vehicle front
Glove compartment. lid
Stopper
Clip
Damper pin
Vehicle front
Connector Foot support
Nut
■ Installation instructions (For MX-5 only)
MX-5 -4
WIRING <Installation of iPod connection adapter only>
Tie redundant part iPod connection cable
Put iPod connection cable in glove compartment (Cable 30 cm from instrument panel)
iPod connection adapter
Pad protector
Loop redundant part of cable andtie it in two locations, then securewith pad protectors. Secure the cable so that it doesn’t get pinched when installing the foot support.
iPod connection adapteriPod connection cable
Vehicle front
Vehicle frontTie wrap (small)
Double-sided adhesive tape (Cut and affix)
○A
○B
○A
Harness (c)To audio unit
Approx.170mm
(Route harness so that this part is approx. 170 mm)
Harness (c)To audio unit
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod connection adapter, be sure to route cablesavoiding sharp edges and burrs on the vehicle's sheet metal. To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to
be adhered. After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with
other parts causing failure or noise.
CAUTION
Vehicle front
Vehicle front
○B
■ Installation instructions (For MX-5 only)
MX-5 -5
• Connect the negative battery cable and verify that all the functions operate while referring to the applicable Owner’s Manual.
Disconnecting the battery causes the DSC indicator light to become inoperable. (At this point, the DSC OFF indicator light flashes and the TCS/DSC indicator light is illuminated.) To restore the DSC to an operable condition, perform the following procedures:
1. Turn the ignition switch to the ON position. 2. Turn the steering wheel completely to the right and then completely to the left. 3. Verify that the DSC OFF indicator light turns off. 4. Turn the ignition switch off and then turn it to the ON position again. 5. Verify that the TCS/DSC indicator light turns off.
If the TCS/DSC or DSC OFF indicator lights do not turn off after turning the ignition switch is turned to the ON position, consult your Mazda dealer.
If the battery is disconnected, the automatic full open/close feature of the power window is disabled. This feature can be reactivated using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds
after it is fully closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda
Dealer.
CAUTION
3. CONNECTION CHECK
■ Installation instructions (For Mazda CX-7 only):
CX-7- 1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Front scuff plate inner removal (driver and front passenger side) 1. Pull the front scuff plate inner upward while detaching tabs A
(2 locations), detach clips B (3 locations), pins C (3 locations) and tabs D (2 locations) from the body, and then remove the front scuff plate inner.
Front side trim removal (driver and front passenger side) 1. Remove the nut.
2. Pull the front side trim in the direction shown by the arrow, then detach clip A (1 location).
Console panel removal 1. Detach clips A (5 locations) from the console using a
tape-wrapped flathead screwdriver. 2. Remove pin B (1 location), tab C (1 location) and pin D
(1 location). 3. Remove the console panel.
Pins C Clips B
Front scuff plate inner
Tabs D
Clips B detail
Tabs A
Front side trim
Clip A detail
Nut
Console panel
Pin B Tab C
Clip A Pin D
Be careful not to damage the scuff plate during removal. CAUTION
Be careful not to tear the seaming welt when pulling it out. CAUTION
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a left-hand drive vehicle, however, the procedure is the same for right-hand drive vehicle.
NOTE
■ Installation instructions (For Mazda CX-7 only):
CX-7- 2
Console removal 1. Remove the shift knob. 2. Pull the panel upward and detach clips A (2 locations), clips B
(6 locations) and tabs C (2 locations). 3. Disconnect the accessory socket connector. 4. Disconnect the seat warmer switch connectors (vehicles with
seat warmer system) 5. Remove the panel.
6. Remove the covers (4 locations). 7. Remove the fasteners (2 locations) and screws (8 locations). 8. Remove the pins A (4 locations). 9. Remove the console.
Glove compartment removal 1. Press the stay damper in the direction shown by the arrow
and detach it from the glove compartment lid. 2. Bend the stoppers inward to remove. 3. Turn the glove compartment downward and pull the pins. 4. Remove the glove compartment.
Lower panel (front passenger side) removal 1. Pull the cover outward and detach the tabs. 2. Remove the cover.
Clips B
Panel
Tabs C
Clips A
Console
Pins A
Console
Cover
Screws
Screw
Screw Cover Cover
Fastener
Screws
Cover
Tab
Cover
Vehicle front
Stopper
Stay damper Glove compartment
Pin
Pin
■ Installation instructions (For Mazda CX-7 only):
CX-7- 3
3. Remove the screws (4 locations). 4. Pull the lower panel (front passenger side) outward and
detach clips A (5 locations). 5. Remove the lower panel (front passenger side).
Hood release lever removal note 1. Pull the lever. 2. While pushing the tab in the direction of the arrow using a
tape-wrapped, small flathead screwdriver, detach it from the lower panel (driver’s side).
3. Under the condition in Step 2, pull the hood release lever
outward, then remove it from the lower panel (driver’s side). Lower panel (driver side) removal 1. Remove the fastener. 2. Pull the cover outward and detach the tabs. 3. Remove the cover.
4. Remove the screw and hood release lever. 5. Pull the lower panel (driver side) outward and detach clips A
(9 locations). 6. Remove the lower panel (driver side).
Lower panel (driver’s side)
Clips A
Screw
Lower panel (front passenger side)
Clips A
Screws
Cover Fastener
Tab
Vehicle front
Tab
Cross-sectional view
Lower panel(driver’s side)
Tab
Be careful not to damage the hood release cable when removing the hood release lever with the flathead screwdriver.
CAUTION
■ Installation instructions (For Mazda CX-7 only):
CX-7- 4
Center panel removal 1. Remove the clips B (2 locations). 2. Pull the center panel outward and detach clips A (10 locations). 3. Remove the center panel. Center panel module removal 1. Remove the screws (4 locations). 2. Pull the center panel module outward slowly and detach pins A
(2 locations), and clips B (2 locations). 3. Disconnect the audio side connectors (2 locations), antenna
feeder, and hazard switch connector, and then remove the center panel module.
Do not apply excessive force when pulling out the center panel; otherwise it could cause an open circuit.
CAUTION
Center panel module
Vehicle front
Pins A
Screws
Clips B
Antenna feeder
Audio side connectors
Hazard switch connector
Center panel
Clips B Clips A Flathead screwdriver
Vehicle front
■ Installation instructions (For Mazda CX-7 only):
CX-7- 5
WIRING <Installation of iPod integration module>
Pad protector (Cut into 50x15 mm and affix)
Double-sided adhesive tape (Cut and affix)
Pad protector
iPod integration module Vehicle
front
Tie wrap (small)
○A
Pad protector (Cut into 50x50 mm and affix)
Tie redundant part
Tie wrap (large) Pad protector
Pad protector
Vehicle front
Harness (c) (To audio unit)(Route harness so that this part is approx. 250 mm)
250mm
Cut 20x30 mm
Glove compartment (backside)
[Glove compartment cutting]
Top
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing malfunction or noise.
CAUTION
Put iPod connection cable in glove compartment (Cable 30 cm from instrument panel)
Vehicle front
Vehicle front
iPod connection cable
Tie wrap (small)
○A
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
iPod connection cable
iPod integration module
Harness (c)(To audio unit)
Tie redundant part(Tie up using 2 straps (large) and secure to heater duct with pad protectors in two locations)
■ Installation instructions (For Mazda CX-7 only):
CX-7- 6
1. Reconnect the negative battery cable and perform an operation check.
3. CONNECTION CHECK
Disconnecting the battery causes the DSC indicator light to become inoperable. (At this point, the DSC OFF indicator light flashes and the TCS/DSC indicator light is illuminated.)
To restore the DSC to an operable condition, perform the following procedures: 1. Turn the ignition switch to the ON position. 2. Turn the steering wheel completely to the right and then completely to the left. 3. Verify that the DSC OFF indicator light turns out. 4. Turn the ignition switch off and then turn it to the ON position again. 5. Verify that the TCS/DSC indicator light turns off.
If the TCS/DSC or DSC OFF indicator lights do not turn off after turning the ignition switch to the ON position, consult your Mazda dealer.
When the battery is disconnected, the power windows will not fully open and close automatically. Perform the following procedure to reactivate the power window automatic operation: 1. Turn the ignition switch to the ON position. 2. Press the switch and fully open the window. 3. Pull up the switch and continue holding for about 2 seconds to fully close the window. 4. If the function does not operate even after the ignition switch is turned off, contact an Authorized Mazda
Dealer.
CAUTION
■ Installation instructions (For BT-50 only):
BT-50-1
Negative battery terminal disconnection 1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.
Center panel unit removal [TYPE A] 1. Remove the climate control dial. 2. Remove the screws.
3. Place your hand in the position indicated in the figure and pull it to secure a space.
4. Insert a flathead screwdriver into the position indicated in the figure from the space where the glove compartment was removed, and push out the center panel unit.
5. Pull the center panel unit outward, detach clip A from the
dashboard, and then remove the center panel unit. 6. Disconnect the audio side connectors, antenna feeder, and
hazard switch connector, and then remove the center panel unit.
Connector
Center panel unit
Antenna feeder plug
Screw
• When installing the center panel unit, make sure that the wiring harness and antenna feeder are not caught between the unit and dashboard. If the wiring harness or the antenna feeder is caught between the unit and dashboard, it may cause malfunctions.
CAUTION
Center panel unit
Clip A
• Perform the procedure while taking care not to damage the connector and wiring harness with the flathead screwdriver.
CAUTION
1. VEHICLE PARTS REMOVAL
A short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to disconnect the negative battery cable and do not allow the terminal to contact any other parts.
WARNING
The procedure described here is for a left-hand drive vehicle, however, the procedure is the same for right-hand drive vehicle.
NOTE
■ Installation instructions (For BT-50 only):
BT-50-2
Glove compartment removal 1. Bend the stoppers inward, then remove. 2. Turn the glove compartment downward and pull the pins. 3. Remove the glove compartment.
Pin
Stopper
Pin
Glove compartment
Stopper
Pin
■ Installation instructions (For BT-50 only):
BT-50-3
WIRING <Installation of iPod connection adapter only>
ハーネスc(オーディオ本体へ)
Vehicle front
Tie wrap (large) Pad protector
Tie redundant part of harness Cand put it in this space
Harness (c)
○A
iPod connection adapter
Tie redundant part (Harness (c))
iPod connection cable
Harness (c) (To audio unit)
Tie redundant part(iPod connection cable)
Vehicle front
Tie wrap (large)
Tie redundant part of iPod connection cable
Approx. 170mm
(Route harness so that this part is approx. 170 mm)
Harness (c) (To audio unit)
○A ○B
iPod connection adapter
Double-sided adhesive tape (Cut and affix)
Dashboard faces backside
Vehicle front
iPod connection adapter
<Installation position enlarged view>
Dashboard facesbackside
Vehicle front
2. INSTALLATION AND WIRING
To prevent an open or short circuit in the wiring of the iPod connection adapter, be sure to route cablesavoiding sharp edges and burrs on the vehicle's sheet metal. To ensure proper adhesion, be sure to degrease the area where the double-sided adhesive tape is to
be adhered. After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with
other parts causing malfunction or noise.
CAUTION
Put iPod connection cable in glove compartment (Cable 30 cm from instrument panel)
Vehicle front
Tie wrap (large)
Dashboard member
○B
To glove compartment
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
■ Installation instructions (For BT-50 only):
BT-50-4
1. Reconnect the negative battery cable.
3. CONNECTION CHECK
Connect the negative battery cable carefully so that it does not interfere with other parts. If the battery is disconnected, the automatic full open/close feature of the power windows is disabled.
This feature can be reactivated using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is fully
closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
CAUTION
■ Installation instructions (For New Mazda2 only)
New Mazda2-1
Negative battery cable disconnection 1. Shift a shift lever to the N position or a selector lever to the N range. 2. Disconnect the negative battery cable and wrap tape around it to insulate.
Instrument panel under cover removal 1. Insert fingers into the service hole and detach hooks (2
locations), guide pin (1 location) by pulling it in the direction of the arrow and remove the Instrument panel under cover.
Glove compartment removal 1. Open the glove compartment and move the damper hook in the
direction of the arrow to unhook it. 2. Press both sides of the glove compartment interior inward in the
direction shown by the arrows (1), remove the pins (2 locations) from the instrument panel, and then remove the glove compartment in the direction shown by the arrow (2).
1. VEHICLE PARTS REMOVAL
The procedure described here is for a left-hand drive vehicle, however, the procedure is the same for the right-hand drive vehicle.
NOTE
When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.
Park the vehicle on a flat, level surface, set the selector lever to P (AT vehicles) or the shift lever to 1st or R (MT vehicles), apply the parking brake and block the wheels so that the vehicle does not move during installation.
WARNING
Vehicle front
Guide pin
Hook
Guide pin Hook Hook
Service hole
Instrument panel under cover
Damper hook
(1)
Pin
Glove compartment
Vehicle front
Pin
Vehicle front
Glove compartment
(1)
(2)
GE
1ED6P11A13600
■ Installation instructions (For New Mazda2 only)
New Mazda2-2
Glove box cover removal 1. Remove the fasteners (3 location). 2. Pull in the direction of the arrow shown in the figure and remove
the glove box cover. Side wall removal (driver and passenger side) 1. Remove the fastener A (1 location). 2. Pull in the directions shown in the figure in the order of (1), (2),
and remove clips B (2 locations) and hook C (1 location). Boot panel removal 1. Remove the shift lever knob (MT vehicles only). 2. Insert a protective tape-wrapped fastener remover into the
position shown in the figure and dislodge the tabs (3 locations). 3. Pull in the direction of the arrow shown in the figure and remove
clips B (2 locations) and clips C (2 locations), and then remove the boot panel.
Vehicle front
Boot panel
Tabs A
Tabs A Tab A
Vehicle front
Boot panel
Clips C
Clips B Clips B
Clip C Clip C
Fastener
Glove box cover Vehicle front
Fastener
Side wall Vehicle front
Fastener A
Clips B
Clips B
Hook C
(1)
(2)
■ Installation instructions (For New Mazda2 only)
New Mazda2-3
Front console removal 1. Remove the screws (2 locations). 2. Pull in the directions shown in the figure in the order of (1), (2)
and remove the clips (6 locations) while removing the front console in the direction of arrow 3.
Center panel module removal 1. Remove the bolt (1) from the underside of the instrument panel
on the front passenger side.
Bolt tightening torque: 1,0 – 6,0 N・m {10,2 – 61,1 kgf・cm・8,9 – 53,1 in・lbf }
Bolt
<View from below>
Vehicle front
Front console
Screw Screw
Vehicle front
Front console
Clips Clips
Clips
(1)
Vehicle front
(3)
(2)
■ Installation instructions (For New Mazda2 only)
New Mazda2-4
2. Remove the screws (2 locations). 3. Pull the center panel module outward slowly and detach tabs A
(2 locations), and clips B (6 locations). 4. Disconnect the audio side connectors (2 locations), antenna
feeder, and hazard switch connector, and then remove the center panel module.
iPod integration module installation 1. Adhere pad protectors halves (3) to the iPod integration module
as shown in the figure. (Two protectors go under the tie wrap, 1 goes in the area behind the bracket contact area.)
2. Adhere double-adhesive tape to the top of the pad protector as shown in the figure.
3. Peel off the backing from the double-sided adhesive tape and adhere the iPod integration module to the vehicle bracket at the back of the glove compartment area.
4. Secure the iPod integration module to the bracket with a tie wrap (large).
2. INSTALLATION AND WIRING
Vehicle front
iPod integration module Bracket
Tie wrap (large)
iPod integration module
Pad protector (half) Double-sided adhesive tape
<Front side> <Back side>
Clips B
Screw
Hazard switch connector
Antenna feeder
Tabs A
Center panel module
Center panel module
Audio side connectors
B
A A
B
B B
B B
Vehicle front
■ Installation instructions (For New Mazda2 only)
New Mazda2-5
WIRING <Installation of iPod integration module only>
○A
Vehicle front
iPod integration module
Put iPod connection cable in glove box (Cable 30 cm from instrument panel)
Fit connector cover when iPod is not connected
Vehicle front
Harness (c) (To audio unit)
Vehicle front
Tie wrap (small)
Tie wrap (small) iPod integration module
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing failure or noise.
CAUTION
Harness (c) (To audio unit)
○A
iPod connection cable
Tie wrap (small)
Approx. 15 cm
iPod integration module Tie wrap (small)
Harness (c)
■ Installation instructions (For New Mazda2 only)
New Mazda2-6
<Installation of iPod integration module and selector box> (For vehicles with AUX terminal)
Selector box installation 1. Adhere two half-pieces of double-sided adhesive tape to the
selector box as shown in the figure. 2. Adhere a half a piece of pad protector, and double-sided
adhesive tape to the selector box as shown in the figure. 3. Adhere a whole pad protector (1). 4. Adhere two half-piece of pad protector to the surface of the
body floor as shown in the figure.
5. Peel of the backing of the double-sided adhesive tape and install the selector box to the top of the pad protector.
Clips
Double-sided adhesive tape (half)
Pad protector (half)
Double-sided adhesive tape (half)
Pad protector
Selector box
Pad protector (half) Vehicle front
Vehicle front
Selector box
Pad protector
(half)
View A
<View A>
Double-sided adhesive tape (half)
Vehicle harness Pad protector
Pad protector (half)
■ Installation instructions (For New Mazda2 only)
New Mazda2-7
WIRING <Installation of iPod integration module and selector box> (For vehicles with AUX terminal )
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing failure or noise.
CAUTION
iPod connection cableSelector box
Harness (c)
Harness (a) (To audio unit)
Harness (b) (To AUX connector)
iPod integration module
Harness (a) (To audio unit)
Harness (b) (To AUX connector)
Approx. 15 cm○A
Put iPod connection cable in glove box (Cable 30 cm from instrument panel)
Fit connector cover when iPod is not connected
Vehicle front
Tie wrap (small)
iPod integration moduleTie wrap (small)
○C
○B
○C
Tie wrap (small)
Harness (c) Vehicle front
Harness (c)
○A
○B
Harness (a) Harness (b)
Tie wrap (large)
Selector box
Vehicle front
■ Installation instructions (For New Mazda2 only)
New Mazda2-8
1. Temporarily install the center panel module in the reverse order of removal so that an operation check can be
performed. 2. Connect the negative battery cable and perform an operation check by referring to the installation and user’s
instructions applicable to the vehicle. 3. If there is any malfunction, disconnect the negative battery cable and verify that each connector is properly
connected and the wiring harnesses are not damaged or pinched, then perform the operation check again. If it does not operate normally, contact the dealer where the unit was purchased. If an error code appears during the operation check, refer to the applicable Workshop Manual for the vehicle and perform the repair.
3. CONNECTION CHECK
Do not insert CDs with labels or other objects attached. Otherwise they could become stuck in the unit. When the battery is disconnected, the windows will not fully open and close automatically.
Perform the following procedure to resume operation: 1. Turn the ignition switch to the ON position. 2. Press the switch and fully open the window. 3. Pull up the switch and continue holding for about 2 seconds to fully close the window. 4. If the function does not operate even after the ignition switch is turned off, contact an Authorized Mazda
Dealer.
CAUTION
■ Installation instructions (For New Mazda6 only)
New Mazda6-1
Negative battery cable disconnection 1. Shift a shift lever to the N position or a selector lever to the N range. 2. Disconnect the negative battery cable and wrap tape around it to insulate.
Glove compartment removal 1. Pull the stay damper in the direction of the arrow shown in the
figure, and detach the connecting part between the glove compartment and the stay damper.
2. Push both ends of the inner-side glove compartment in the direction of the arrow in the figure.
3. Lower the glove compartment. 4. Detach the hook from the dashboard and remove the glove
compartment.
1. VEHICLE PARTS REMOVAL
The procedure described here is for a right-hand drive vehicle, however, the procedure is the same for the left-hand drive vehicle.
NOTE
When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.
Park the vehicle on a flat, level surface, set the selector lever to P (AT vehicles) or the shift lever to 1st or R (MT vehicles), apply the parking brake and block the wheels so that the vehicle does not move during installation.
WARNING
GE
1ED6P11A15900
Stay damper
Glove compartment
Glove compartment
Hook
Glove compartment
■ Installation instructions (For New Mazda6 only)
New Mazda6-2
Upper panel removal 1. Pull the upper panel in the direction of the arrow in the order of
(1) and (2), then remove it while detecting the clip A, B and C. 2. Move the upper panel and remove it. Decoration panel removal (Driver-side) 1. Pull the decoration panel in the direction of the arrow in the
order of (1) and (2), then remove it while detaching the clips and hooks.
Decoration panel removal (Passenger-side) 1. Pull the decoration panel in the direction of the arrow in the
order of (1) and (2), then remove it while detaching the clips and hooks.
When removing clip A, press the connecting part of the center lower panel with a hand to prevent damage to clip A.
CAUTION
Upper panel
Clip A
Clip B
Clip C
(1)(2)
Clip B
Clip A
Clip C
Parking brake lever
(3)
Upper panel
Clip B
(1)
(2)
Hook A Hook A
Clip B
Clip B
Decoration panel (Passenger-side)
Clip B
(1)
(2) Clip B
Clip B
Hook A
Hook A
Decoration panel (Driver-side)
■ Installation instructions (For New Mazda6 only)
New Mazda6-3
Side panel removal (Passenger-side) 1. Pull the side panel in the direction of the arrow in the order of
(1) and (2), then remove it while detaching the clips.
Boot Panel removal (MTX) 1. Remove the shift lever knob. 2. Pull the boot panel in the direction of the arrow shown in the
figure and disengage hooks. Shift panel removal (AT) 1. Pull the shift panel in the direction of the arrow shown in the
figure and remove it while detaching clips, and the hooks. Center panel lower removal 1. Pull the center panel lower in the direction of the arrow (1)
shown in the figure while detaching clips. 2. Pull the center panel lower in the direction of the arrow (2)
shown in the figure and remove it while detaching clips and hooks.
3. Disconnect the sear warmer switch connector.(for Vehicles with seat warmer)
4. Disconnect the cigarette lighter socket connector. 5. Remove the ash tray illumination bulb.
Clip
Side panel
(1)
(2)
Clip
Clip
(1)
(2)
Hook
Clip Clip
Hook Hook Clip Clip
Center panel lower
Hook
Hook
Hook
Hook
Hook
Boot panel
Hook
Hook
Hook
Hook
Hook
Shift panel
■ Installation instructions (For New Mazda6 only)
New Mazda6-4
Center panel upper removal 1. Insert a tape-wrapped fastener remover into the position
indicated by the arrow in the figure, slide it to remove the hooks, and raise the front side of the center panel upper.
2. Pull the center panel upper in the direction of the arrow shown
in the figure and remove it while detaching clips. 3. Disconnect the hazard switch connector and passenger-side
seat belt warning connector.
Climate control unit removal 1. Remove the screws and climate control unit. 2. Disconnect the climate control unit connectors and remove the
climate control unit. Audio unit removal 1. Remove the screws (3) and bolt (1). 2. Disconnect the audio side connectors (2 locations) and antenna feeder.
Screw
Screw Bolt
Climate control unit
Climate control unit connector
Screw
Clip
Clip Clip
Clip Center panel upper
Hook Hook
Hook
Hook
Center panel upper
Bolt: 6.9―9.8 N・m 71―99 kgf・cm 62―86 in・lbf
■ Installation instructions (For New Mazda6 only)
New Mazda6-5
Rear console removal 1. Disconnect the connector and remove the wiring harness clip. 2. Remove the screws A, B and screw C. 3. Open the console lid and remove the screws D. 4. Pull the rear console in the direction of the arrow in the order of
(1), then detaching clip E. 5. Pull up the rear console in the direction of the arrow (2) shown
in the figure, move the rear console in the direction of the arrow (3, and remove it avoiding the parking brake lever.
Tab A
Clip B
Screw D
Rear console
Clip E Rear console
Clip E
(1)
(2)
Rear console
(3)
Rear console
Screw A
Screw B
Screw C
Pull the audio unit outward, detach tab, clip from the dashboard, and then remove the audio unit.
NOTE
■ Installation instructions (For New Mazda6 only)
New Mazda6-6
<Installation of iPod integration module and selector box>
Selector box installation 1. Adhere two half-pieces of pad protector to the selector box as
shown in the figure. 2. Adhere double-sided adhesive tape to the selector box as
shown in the figure. 3. Adhere two overlapped pad protector halves under the bracket
bolt of the body as shown in the figure.
4. Peel off the backing of the double-sided adhesive tape and install the selector box to the top of the pad protector.
Clips
2. INSTALLATION AND WIRING
Pad protector (half)
Double-sided adhesive tape
Selector box
View A
Double-sided adhesive tape
Bolt Pad protector
(half)
Pad protector (half)
<View A>
Pad protector (half)
Vehicle front
Selector box
Bolt
Vehicle front
Selector box
■ Installation instructions (For New Mazda6 only)
New Mazda6-7
WIRING <Installation of iPod integration module and selector box>
To prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables avoiding sharp edges and burrs on the vehicle's sheet metal.
To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is to be adhered.
After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with other parts causing failure or noise.
CAUTION
Pad protector (Attach to edge)
Tie wrap (large)
Selector box
Vehicle front
Tie wrap (large)Harness (b) (To AUX terminal)
Harness (a) (To audio unit)
Tie wrap (large)
Tie wrap (large)Harness (a) (To audio unit)
Harness (b) (To AUX terminal)
○A
○A
○B
Harness (b) (To AUX terminal)
Harness (a) (To audio unit)
Tie wrap (large)
Put iPod connection cable in glove box (Cable 30 cm from instrument panel)
○C
○C
iPod integration module
Remove connector cover when connecting iPod; fit connector cover when iPod is not used
Approx. 170mm(Route harness so that this part isapprox. 170 mm)
Selector box
○B
iPod integration module
Tie wrap (small)
Pad protector
Vehicle front
Double-sided adhesive tape(Back side)
■ Installation instructions (For New Mazda6 only)
New Mazda6-8
1. Temporarily install the center panel module in the reverse order of removal so that an operation check can be
performed. 2. Connect the negative battery cable and perform an operation check by referring to the installation and user’s
instructions applicable to the vehicle. 3. If there is any malfunction, disconnect the negative battery cable and verify that each connector is properly
connected and the wiring harnesses are not damaged or pinched, then perform the operation check again. If it does not operate normally, contact the dealer where the unit was purchased. If an error code appears during the operation check, refer to the applicable Workshop Manual for the vehicle and perform the repair.
3. CONNECTION CHECK
Disconnecting the battery causes the DSC indicator light to become inoperable. (At this point, the DSC OFF indicator light flashes and the TCS/DSC indicator light is illuminated.)
To restore the DSC to an operable condition, perform the following procedures: 1. Turn the ignition switch to the ON position. 2. Turn the steering wheel completely to the right and then completely to the left. 3. Verify that the DSC OFF indicator light turns off. 4. Turn the ignition switch off and then turn it to the ON position again. 5. Verify that the TCS/DSC indicator light turns off.
If the TCS/DSC or DSC OFF indicator lights do not turn off after turning the ignition switch is turned to the ON position, consult your Mazda dealer.
If the battery is disconnected, the automatic full open/close feature of the power window is disabled. This feature can be recovered using the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two seconds
after it is fully closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda
Dealer.
CAUTION