MAKE: STYLE:

45

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITYFor more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY: MODERATE

EASY MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be worn at all times whileinstalling this product.

YEARS: 2017-CURRENT HYUNDAI MODEL: ELANTRA SEDAN

2,000200

TRAILER WEIGHT:TONGUE WEIGHT:

11424 INSTALLATION INSTRUCTIONS

LBS.LBS.

WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.

90 MIN.MIN. PRO INSTALL TIME:

NOVICE INSTALL TIME:

IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

SCAN FORMORE INFO

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.comThis product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 2/26/2016

SCREWDRIVER SOCKET

10mm15mm17mm9/16" SOCKET

EXTENSION

6"

RATCHETTORQUE

WRENCHMASKING

TAPE

TAPEMEASUREDIE GRINDER

NO DRILLING REQUIRED

LOWER EXHAUST

TRIM UNDERBODY PANEL

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

Parts List

DESCRIPTIONPART NUMBERQTYITEM

3/8-16 x 1.938 x .875" U-BOLTCM-3805-UBR11

HEX BOLTM10-1.25 x 3542

CONICAL TOOTHED WASHER7/16"43

HEX NUT3/8 - 1624

LOCK WASHER3/8"25

WASHER5/16"26

EXISTING VEHICLE TOW LOOP

DRIVER SIDEFRAME RAIL

DESIGNED FOR USE WITHBALL MOUNT # D-21 / 45521

EURO MOUNT OPTION AVAILABLE#45571 (1-7/8" BALL) #45572 (2" BALL)

PASSENGER SIDEFRAME RAIL

1

2 3

4

5

6

1. Lower exhaust by detaching (2) rubber isolators towards rear of vehicle. (See RUBBER ISOLATOR REMOVEL DIAGRAM)

2. Temporarily remove driver side underbody panel by removing (3) clips using a flat head screwdriver and (4) nuts using a 10mm socket.

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

3. Remove (2) bolts using a 15mm socket on driver and passenger sides of vehicle on front facing section that attaches to the bumper beam. Place 3/8" u-bolt over vehicle tow loop.

4. Raise hitch into position and slide u-bolt through holes in hitch. Secure hitch to vehicle with M10 bolts and 7/16" conical toothed washers into locations where bolts were removed in step 3. Install 5/16" flat washers, 3/8" lock washers and 3/8" hex nuts onto u-bolt.

5. Torque M10 hardware to 86 lb-ft and 3/8" hardware to 26 lb-ft.

6. Mark cut location of underbody panel. (See UNDERBODY PANEL TRIM DIAGRAM) Cut out marked location using cutoff wheel.

1 in1.75 in

3.5 in

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

7. Reinstall underbody panel in reverse order of step 2. Raise exhaust into position and reattach exhaust isolators.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.

WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **

WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

2,000 200

24

45

HYUNDAI ELANTRA2/25/201611424

90

Scanfor moreinformation

PAGE 1 of 2

Parts ListDESCRIPTIONPART NUMBERQTYITEM

3/8-16 x 1.938 x .875" U-BOLTCM-3805-UBR11HEX NUT3/8 - 1622LOCK WASHER3/8"23WASHER5/16"24HEX BOLTM10-1.25 x 3545CONICAL TOOTHED WASHER7/16"46 5 6

1

4

3

2

EXISTING VEHICLE TOW LOOP

PASSENGER SIDEFRAME RAIL

DRIVER SIDEFRAME RAIL

DESIGNED FOR USE WITHBALL MOUNT # D-21 / 45521

EURO MOUNT OPTION AVAILABLE#45571 (1-7/8" BALL) #45572 (2" BALL)

- NO DRILLING REQUIRED- LOWER EXHAUST- TRIM UNDERBODY PANEL

TOOLS REQUIREDFLAT HEAD SCREWDRIVER10mm,15mm,17mm SOCKET

9/16" SOCKET6" SOCKET EXTENSION

SOCKET WRENCHTORQUE WRENCH

TAPECUTOFF WHEELTAPE MEASURE

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

HYUNDAI ELANTRA2/25/2016

11424PAGE 2 of 2

1. Lower exhaust by detaching (2) rubber isolators towards rear of vehicle. (See RUBBER ISOLATOR REMOVEL DIAGRAM) 2. Temporarily remove driver side underbody panel by removing (3) clips using a flat head screwdriver and (4) nuts using a 10mm socket. 3. Remove (2) bolts using a 15mm socket on driver and passenger sides of vehicle on front facing section that attaches to the bumper beam. 4. Place 3/8" u-bolt over vehicle tow loop. 5. Raise hitch into position and slide u-bolt through holes in hitch. Secure hitch to vehicle using supplied M10 bolts and 7/16" conical toothed washers. Fasten to vehicle into locations where bolts were removed in step 3. (See CONICAL TOOTHED WASHER ORIENTATION DIAGRAM) 6. Install 5/16" flat washers, 3/8" lock washers and 3/8" hex nuts onto u-bolt. 7. Torque M10 hardware to 48 lb-ft and 3/8" hardware to 26 lb-ft. 8. Mark cut location of underbody panel. (See UNDERBODY PANEL TRIM DIAGRAM) 9. Cut out marked location using cutoff wheel. 10. Reinstall underbody panel in reverse order of step 2. 11. Raise exhaust into position and reattach exhaust isolators.

1 in1.75 in

3.5 in

UNDERBODY PANEL TRIM DIAGRAM