installation manual car-10 (teltonika fm22,fm42, fm41, fm11)

GPS Fleet Software (www.gpsfleetsoftware.com)

Copyright © Software-Management Gmbh - Seite 1 von 13

Installation Manual Car-10 (Teltonika FM22,FM42, FM41, FM11)

Important InformationGeneral Information

DatasheetNavigate LED operation (GPS Signal)Status LED operation (GSM)

Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and IgnitionPositioning of the device with GPS antenna insde the devicePositioning of the device (optional)Installation Tests:

FM41 (GFSx44) Tracking DeviceFM41 Plug & PinsLED's

FM22 (GFSx22) Connection PlanLED's

FM42 (GFSx44) Connection PlanLED's

AccessoriesDriver Identification via I-Button Installation for FM4100 onlyDriver Identification via I-Button and Buzzer - FM41Driver Identification via I-Button and Buzzer - FM4200Temperature Sensors for GFSx44 (FM4100)Temperatur-Sensors FM4200

Installation Tests:Troubleshooting

Important InformationTroubleshooting RMA

General Instructions

Troubleshooting RMA

General Information

Datasheet

FM4200 User Manual v1.6.pdf

FM4100_User_Manual_v3.0.pdf

https://knowhow.gps.at/display/GPSEN/Troubleshooting+RMA

https://knowhow.gps.at/display/GPSEN/General+Instructions


https://knowhow.gps.at/download/attachments/1050177/FM4200%20User%20Manual%20v1.6.pdf?version=1&modificationDate=1431517501936&api=v2

https://knowhow.gps.at/download/attachments/1050177/FM4100_User_Manual_v3.0.pdf?version=1&modificationDate=1431517501919&api=v2



FM4100_User_Manual_v3.0.pdf

FM1100_User_Manaul_v015.pdf

image2015-5-15 11:27:48.png

Navigate LED operation (GPS Signal)

If ignition is ON and connected, the Navigate LED must blink every second.

Behavior Meaning

Permanently switched on GPS signal is not received

Blinking every second Normal mode, GPS is working

Off GPS is turned off because of deep sleep mode

Or GPS antenna short circuited

Status LED operation (GSM)

If ignition is ON and connected, the LED must blink every second and faster if data is transferred.

Behavior Meaning

Blinking every second Normal mode

Blinking every 2 seconds Deep sleep mode

Blinking fast for a short time Modem activity

Blinking fast constantly Boot mode

Off Device is not working or device firmware being flashed

Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and Ignition

Refer to the sticker on the device to find the correct wire for ignition, main power and ground!

PIN Typ Color Required Description

1 VCC DC YES Permanent power (10-30 Volt)

2 OUT2 Output 2

https://knowhow.gps.at/download/attachments/1050177/FM4100_User_Manual_v3.0.pdf?version=1&modificationDate=1431517501919&api=v2

https://knowhow.gps.at/download/attachments/1050177/FM1100_User_Manaul_v015.pdf?version=1&modificationDate=1431517501880&api=v2

https://knowhow.gps.at/download/attachments/1050452/image2015-5-15%2011%3A27%3A48.png?version=1&modificationDate=1431682235182&api=v2



3 OUT1 Output 1

4 DIN 2 optional Input 2: e.g. privat switch

5 DIN 1 YES Input 1: connect with ignition signal

6 GND YES connect with ground

7 AIN 1 Analogue input (voltage values)

8 Data Dallas iButton driver data

9 DIN 3 Input 3

10 UCC Dallas iButton

Positioning of the device with GPS antenna insde the device

The device shall be placed UNDER the plastic dashbord with the sticker showing to the sky.

Positioning of the device (optional)

If acceleration plays a role, the device should be positioned horizontally and the main wire should show to the back or in driving direction

Installation Tests:

see Installation Tests and Reporting

FM41 (GFSx44) Tracking Device

https://knowhow.gps.at/display/GPSEN/Installation+Tests+and+Reporting



FM41 Plug & Pins

PIN Type Colour Description

1 VCC (10-30) V DC Black Power + 10 V - 30 V DC Direct Current

11 GND (12-30) V DC Black Ground

16 DIN 1 Black Digital input / Ignition

LED's



FM22 (GFSx22) Connection Plan

The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.





2 VCC (10-30) V DC Red Permanent power + 10 V - 30 V Direct Current

3 DIN 1 Yellow Digital input 1 / Ignition

LED's

FM42 (GFSx44) Connection Plan



The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.

The following diagram shows how to connect to .main power, ground and ignition





11 VCC (10-30) V DC Red Power + 10 V - 30 V Direct Current

15 DIN 1 Yellow Digital input 1 / Ignition

LED's

AccessoriesAccessories only work with the right tracking unit GFSx44 and are not included in the standard delivery.

You only have to read this chapter if you need to fix the accessories.

Take care that the FM4100 and FM4200 require DIFFERENT wiring connections.

It might be necessary to configure additional settings in the software in order to use the accessories.



Driver Identification via I-Button Installation for FM4100 only

The accessories must be provided by the same vendor as the tracking unit or it must be guaranteed that exactly the same type ibuttons and readers is used to make it work:

The I-Button Installation is only necessary for vehicles that shall be equipped with a driver identification. I-Button Installation only works with FM41 Box!

Connect and test the following:


11 GND Grey iButton cable

8 Data White iButton cable

To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK SMS Test NOT OK

GPS - - USR PWD readio 78 IO ID:78 Value:318767235 Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

To test the installation, make sure that the ibutton is on the reader.



Driver Identification via I-Button and Buzzer - FM41

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information.

In case if engine is started without connected Ibutton, in 5 seconds the external Buzzer connected to FM4100 is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. . The digital input 3 must be connected to ignition.

Connection Plan:


11 GND Grey iButton cable

8 Data White iButton cable

18 DIN3 Ignition must be connected to DIN3 (not DIN1)

1 VCC Power Green Must be connected to Buzzer and reader

4 OUT3 Yellow Must be connect to Buzzer and

To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box



TESTS

LED lights ok

LED lights NOT OK







Driver Identification via I-Button and Buzzer - FM4200

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information. In case if engine is started without connected Ibutton, the external Buzzer connected to device is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. The digital input 1 must be connected to ignition.

Connection Plan:


1 GND Black Grey iButton cable

13 1-Wire Data White iButton cable

15 DIN1 Yellow Ignition must be connected to DIN1

11 VCC Power Red Green iButton Cable

19 OUT1 Yellow iButton cable (based on ground) Must be connect to Buzzer and

11 VCC Power Red Red cable of alarm buzzer

19 OUT1 Black Black cable of alarm buzzer must be connected to ground

Temperature Sensors for GFSx44 (FM4100)



The temperature sensor is converting temperature into „iButton signal“.

Sensor type must be DS1820-PUR-7M. Connect and test the following


20 PWD Data Green cable of sensor

8 Data Brown cable of sensor

11 GND White cable of sensor

Test per SMS

Temperatur-Sensors FM4200

Sensor type must be DS1820-PUR-7M. Connect and test the following:




3 1 W PWD Data Green cable of sensor

13 1 W Data Brown cable of sensor

1 GND White cable of sensor

Tests per SMS:

TESTS

LED lights ok

LED lights NOT OK







Installation Tests:see Installation Tests and Reporting

Troubleshootingsee Troubleshooting RMA

https://knowhow.gps.at/display/GPSEN/Installation+Tests+and+Reporting


installation manual car-10 (teltonika fm22,fm42, fm41, fm11)

Documents