installation manual (split type) english …...air conditioner (split type) installation manual...

AIR CONDITIONER (SPLIT TYPE)INSTALLATION MANUAL

Indoor unitRAS-B10, 13, 16PKVSG-E

Outdoor unitRAS-10, 13, 16PAVSG-E

1122950102-1

R32

ENGLISH

00_1122950102-1-Cover.indd 100_1122950102-1-Cover.indd 1 5/21/2562 BE 10:54 AM5/21/2562 BE 10:54 AM

PRECAUTIONS FOR SAFETY ....................................................1ACCESSORY PARTS ..................................................................5INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS .......................................................................6

Optional Installation Parts .......................................................6INDOOR UNIT ..............................................................................7

Installation Place .....................................................................7 Cutting a Hole and Mounting Installation Plate .......................7 How to Connect Remote Controller for Wire Operation ..........7 Piping and Drain Hose Installation ..........................................8 Indoor Unit Fixing ....................................................................9 Drainage ..................................................................................9

OUTDOOR UNIT ........................................................................10 Installation Place ...................................................................10 Precautions about Installation in Regions with Snowfall

and Cold Temperatures .........................................................10 Refrigerant Piping Connection ..............................................10 Evacuating ............................................................................ 11

ELECTRICAL WORKS ..............................................................12 In Case of Indoor Unit Connect With 1:1 Outdoor Unit .........13 In Case of Indoor Unit Connect With Inverter Multi System

(IMS) ......................................................................................15OTHERS .....................................................................................16

Gas Leak Test........................................................................16 Remote Control A-B Selection ...............................................16 Test Operation ......................................................................16 Auto Restart Setting .............................................................16

APPENDIX .................................................................................17

PRECAUCIONES SOBRE SEGURIDAD ....................................1ACCESSORIOS ...........................................................................5DIAGRAMA DE INSTALACIÓN DE LA UNIDAD INTERIOR Y EXTERIOR ...................................................................................6

Piezas de Instalación Opcional ..............................................6UNIDAD INTERIOR .....................................................................7

Lugar de Instalación ................................................................7 Corte de un Orifi cio y Montaje de la Placa de Instalación ......7 Cómo conectar el mando a distancia para la función de

cableado ..................................................................................7 Instalación la Tubería y el Tubo de Desagüe .........................8 Instalación de la Unidad Interior ..............................................9 Drenaje ...................................................................................9

UNIDAD EXTERIOR ..................................................................10 Lugar de Instalación ..............................................................10 Precauciones sobre Instalación en Regiones con Nieve y

Temperaturas Frías ...............................................................10 Conexión de la Tubería Refrigerante ....................................10 Evacuación ............................................................................ 11

TRABAJOS ELÉCTRICOS ........................................................12 En caso de la unidad interior conectar con la unidad

exterior 1:1 ............................................................................13 En caso de conexión de la unidad interior con el sistema

múltiple del inversor (IMS) .....................................................15OTROS .......................................................................................16

Comprobación de Fugas .......................................................16 Mando a distancia A-B Selección ..........................................16 Prueba de Operación ...........................................................16 Ajuste de Reinicio Automático ..............................................16

APÉNDICE .................................................................................17

CONTENTSEN CONTENIDOS ES SOMMAIREFR

INDICEIT INHALTDE ÍNDICEPT

SPIS TREŚCIPL OBSAHCZ ΠΕΡΙΕXOΜΕΝΑGR

SICHERHEITSVORKEHRUNGEN ..............................................1ZUBEHÖRTEILE ..........................................................................5EINBAUZEICHNUNGEN FÜR INNEN- UND AUSSENGERÄT ..6

Zusätzlich erhältliche Installationsteile ...................................6INNENGERÄT ..............................................................................7

Aufstellungsort .........................................................................7 Mauerdurchbruch und Befestigung der Montageplatte ..........7 Verbindung der Fernbedienung zur Funktion per

Kabelanschluss .......................................................................7 Installation von Leitungen und Kondensatschlauch ................8 Einbau des Innengeräts ..........................................................9 Entwässerung .........................................................................9

AUSSENGERÄT ........................................................................10 Aufstellungsort .......................................................................10 Vorsichtsmaßnahmen beim Einbau in Regionen mit

Schneefall und kalten Temperaturen .....................................10 Anschluß der Kühlmittelleitungen ..........................................10 Entleeren .............................................................................. 11

ELEKTRISCHE ANSCHLÜSSE ................................................12 Bei der 1:1-Verbindung eines Innengeräts mit einem

Aussengerät ..........................................................................13 Bei der Verbindung eines Innengeräts mit einem

Multi-Inverter-System (IMS) ..................................................15SONSTIGES...............................................................................16

Überprüfung auf Gas-Undichtigkeit .......................................16 Fernbedienung A-B Wahl ......................................................16 Probelauf ...............................................................................16 Automatische Wiedereinschaltung ........................................16

ANHANG ....................................................................................17

MESURES DE SÉCURITÉ ...........................................................1PIÈCES ACCESSOIRES .............................................................5PLAN D’INSTALLATION DES UNITÉS INTÉRIEURE ET EXTÉRIEURE...............................................................................6

Pièces d’Installation en Option ...............................................6UNITÉ INTÉRIEURE ....................................................................7

Endroit d’Installation ................................................................7 Ouverture du Trou et Montage de la Plaque d’Installation .....7 Comment se connecter avec la télécommande pour un

fonctionnement par câble ........................................................7 Installation de la Conduite et du Tuyau de Purge ...................8 Installation de l’Unité Intérieure ...............................................9 Drainage .................................................................................9

UNITÉ EXTÉRIEURE .................................................................10 Endroit d’Installation ..............................................................10 Précautions à prendre pour l’installation dans les régions

sujettes aux chutes de neige et aux températures froides ....10 Connexion du Tuyau Réfrigérant ...........................................10 Evacuation ............................................................................ 11

TRAVAUX ÉLECTRIQUES .......................................................12 En cas de raccordement d’une unité intérieure avec une

unité extérieure 1:1 ................................................................13 En cas de raccordement d’une unité intérieure avec un

système multiple à inverseur (IMS) .......................................15AUTRES .....................................................................................16

Test de Fuite Gaz ..................................................................16 Sélection de télécommande A-B ...........................................16 Opération du Test .................................................................16 Réglage de la Remise en Marche Automatique ...................16

ANNEXE.....................................................................................17

PRECAUZIONI PER LA SICUREZZA .........................................1ACCESSORI ................................................................................5SCHEMA DI INSTALLAZIONE DELL’ UNITÀ INTERNA E DELL’ UNITÀ ESTERNA .............................................................6

Componenti di Installazione Opzionali ...................................6UNITÀ INTERNA .........................................................................7

Luogo per l’Installazione ..........................................................7 Apertura di un Foro e Installazione della Lastra di Installazione ...7 Come collegare il controller remoto per le operazioni di

cablaggio .................................................................................7 Installazione dei Tubi e del Tubo di Scarico ............................8 Installazione dell’Unità Interna ................................................9 Scarico ....................................................................................9

UNITÀ ESTERNA ......................................................................10 Luogo per l’Installazione ........................................................10 Precauzioni sull’installazione nelle regioni soggette a

nevicate e basse temperature ...............................................10 Collegamento dei Tubi del Refrigerante ................................10 Evacuazione ......................................................................... 11

LAVORI ELETTRICI ...................................................................12 In caso di collegamento dell’unità interna con l’unità

esterna 1:1 ............................................................................13 In caso di collegamento dell’unità interna con multisistema

inverter (IMS) .........................................................................15ALTRI .........................................................................................16

Test per Perdite di Gas ..........................................................16 Selezione A-B del telecomando ............................................16 Funzionamento di Prova .......................................................16 Impostazione per la Rimessa in Funzione Automatica .........16

APPENDICE...............................................................................17

PRECAUÇÕES RELATIVAS A SEGURANÇA ............................1ACESSÓRIOS..............................................................................5ESQUEMA DE INSTALAÇÃO DAS UNIDADES INTERIOR E EXTERIOR ................................................................................6

Peças de Instalação Opcionais ...............................................6UNIDADE INTERIOR ...................................................................7

Local de Instalação .................................................................7 Cortar um Orifício e Montar a Placa de Instalação .................7 Como ligar o controlo remoto para funcionamento com cabo ..7 Instalação da Tubagem e do Tubo Flexível de Dreno .............8 Colocação da Unidade Interior ................................................9 Drenagem ................................................................................9

UNIDADE EXTERIOR ................................................................10 Local de Instalação ...............................................................10 Precauções na instalação em regiões com queda de neve

e temperaturas negativas ......................................................10 Ligação das Condutas de Refrigeração ................................10 Purga de Ar ........................................................................... 11

TRABALHOS DE ELECTRICIDADE .........................................12 Em Caso de Ligação da Unidade Interior Com 1:1

Unidade Exterior ....................................................................13 Em Caso de Ligação da Unidade Interior Com

Multi-Sistema Inversor (IMS) .................................................15OUTROS ....................................................................................16

Teste de Fugas de Gás .........................................................16 Selecção A-B do telecomando ..............................................16 Execução do Teste ................................................................16 Defi nindo de Reiniciação Automática ....................................16

APÊNDICE .................................................................................17

ZASADY BEZPIECZEŃSTWA .....................................................1CZĘŚCI DODATKOWE ................................................................5SCHEMAT INSTALACYJNY URZĄDZENIA WEWNĘTRZNEGO I ZEWNĘTRZNEGO ....................................6

Dodatkowe Części Instalacyjne ...............................................6URZĄDZENIE WEWNĘTRZNE ...................................................7

Miejsce Instalacji .....................................................................7 Wycinanie Otworu oraz Montaż Płyty Instalacyjnej .................7 W jaki sposób podłączyć pilot zdalnego sterowania do

pracy z wykorzystaniem kabla .................................................7 Montaż Instalacji Rurowej i Węża do Odprowadzania Cieczy ..8 Mocowanie Urządzenia Wewnętrznego ..................................9 Odprowadzanie Cieczy ...........................................................9

URZĄDZENIE ZEWNĘTRZNE ..................................................10 Miejsce Instalacji ...................................................................10 Zalecenia dotyczące instalacji urządzenia w rejonach z

występowaniem obfi tych opadów śniegu i niskich temperatur ..10 Łączenie Instalacji Rurowej Czynnika Chłodniczego ............10 Usuwanie Powietrza .............................................................. 11

PRACE ELEKTRYCZNE............................................................12 W przypadku podłączenia jednostki wewnętrznej do

jednostki zewnętrznej 1:1 ......................................................13 W przypadku podłączenia jednostki wewnętrznej z

wielosystemowym inwerterem (IMS) .....................................15INNE ...........................................................................................16

Próba Gazoszczelności .........................................................16 Ustawienia przełącznika A-B wyboru pilota ...........................16 Próba Działania .....................................................................16 Włączanie Funkcji Automatycznego Wznawiania Pracy

(Auto Restart) ........................................................................16ZAŁĄCZNIK ...............................................................................17

BEZPEČNOSTNÍ OPATŘENÍ ......................................................1DÍLY PŘÍSLUŠENSTVÍ ................................................................5SCHÉMA INSTALACE VNITŘNÍ A VENKOVNÍ JEDNOTKY ......6

Volitelné Doplňky pro Instalaci ................................................6VNITŘNÍ JEDNOTKA ..................................................................7

Místo Instalace ........................................................................7 Vyvrtání Otvoru a Montáž Instalační Desky ............................7 Jak Zapojit Dálkové Ovládání pro Spuštění Provozu ..............7 Montáž Trubek a Vypouštěcí Hadice .......................................8 Montáž Vnitřní Jednotky ..........................................................9 Odvod Vody .............................................................................9

VENKOVNÍ JEDNOTKA ............................................................10 Místo Instalace ......................................................................10 Pokyny pro Instalaci v Oblastech, kde Padá Sníh a jsou

Nízké Teploty .........................................................................10 Spojování Chladivového Potrubí ...........................................10 Vyčerpávání Vzduchu ............................................................ 11

ELEKTROINSTALAČNÍ PRÁCE ...............................................12 Jestliže je vnitřní jednotka spojena s venkovní

jednotkou 1:1 .........................................................................13 Jestliže je vnitřní jednotka spojena s invertorovým

multisystémem (IMS) .............................................................15OSTATNĺ ....................................................................................16

Zkouška Úniku Plynu .............................................................16 Volba A-B na Dálkovém Ovládání .........................................16 Zkušební Provoz ...................................................................16 Nastavení Automatického Znovuspuštění .............................16

DODATEK ..................................................................................17

ΠΡOΦΥΛΑ�ΕΙΣ ΑΣΦΑΛΕΙΑΣ .......................................................1ΕΞΑΡΤΗΜΑΤΑ .............................................................................5ΔΙΆΓΡΑΜΜΑ ΕΓΚΑΤΆΣΤΑΣΗΣ ΤΗΣ ΕΣΩΤΕΡΙΚΉΣ ΚΑΙ Ε�ΩΤΕΡΙΚΉΣ ΜOΝΆΔΑΣ ..........................................................6

Πρ�αιρετικά E�αρτήματα Eγκατάστασης ...........................6ΕΣΩΤΕΡΙΚΉ ΜOΝΆΔΑ ...............................................................7

Σημεί� Eγκατάστασης ..........................................................7 Κ�ψιμ� Τρύπας και Τ�π�θέτηση Πλάτης Εγκατάστασης ...7 Σύνδεση τoυ τηλε&ειριστηρίoυ για την Ενσύρματη

λειτ�υργία ..............................................................................7 Εγκατάσταση Σωλήνωσης και Eύκαμπτ�υ Σωλήνα Aπ�στράγγισης ..8 Στερέωση Εσωτερικής Μoνάδας .........................................9 Απoστράγγιση ........................................................................9

Ε�ΩΤΕΡΙΚΉ ΜOΝΆΔΑ .............................................................10 Σημείo Εγκατάστασης ........................................................10 Πρo)υλά�εις σ&ετικά με την εγκατάσταση σε περιo&ές

με &ιoν�πτωση και &αμηλές θερμoκρασίες......................10 Σύνδεση Ψυκτικών Σωληνώσεων ......................................10 Εκκένωση ............................................................................. 11

ΗΛΕΚΤΡΙΚEΣ ΕΡΓΑΣIΕΣ ...........................................................12 Σε Περίπτωση Σύνδεσης Εσωτερικής Μονάδας με Εξωτερική Μονάδα 1:1 ..........................................................13

Σε Περίπτωση Σύνδεσης Εσωτερικής Μονάδας με Πολυδιαιρούμενο Σύστημα Inverter (IMS) .............................15

ΛOΙΠΑ ........................................................................................16 Έλεγ&oς Διαρρoής Αερίoυ .................................................16 Επιλ�γή Α-Β τoυ τηλε&ειριστηρίoυ ...................................16 Δoκιμή Λειτoυργίας ............................................................16 Auto Restart Ρύθμιση .........................................................16ΠΑΡΆΡΤΗΜΑ .............................................................................17

00_1122950102-1-Cover.indd 200_1122950102-1-Cover.indd 2 5/21/2562 BE 10:54 AM5/21/2562 BE 10:54 AM

EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI1

PRECAUTIONS FOR SAFETYPRECAUTIONS FOR SAFETY

• Before installation, please read these precautions for safety carefully.• Be sure to follow the precautions provided here to avoid safety risks. The

symbols and their meanings are shown below.WARNING : It indicates that incorrect use of this unit may cause severe injury or

death. CAUTION : It indicates that incorrect use of this unit may cause personal injury

(*1), or property damage (*2). *1: Personal injury means a slight accident, burn, or electrical shock

which does not require admission or repeated hospital treatment. *2: Property damage means greater damage which affects assets or

resources.

For general public usePower supply cord and connecting cable of appliance use shall be at least polychloroprene sheathed fl exible cord (design H07RN-F) or cord designation 60245 IEC66. (Shall be installed in accordance with national wiring regulations.)

This appliance must be connected to the main power supply by means of a circuit breaker or a switch with a contact separation of at least 3 mm in all poles.

CAUTION To disconnect the appliance from the main power supply

Read the precautions in this manual carefully before operating the unit.

This appliance is fi lled with R32.

01_1122950102-1-EN.indd 101_1122950102-1-EN.indd 1 5/13/2562 BE 2:28 PM5/13/2562 BE 2:28 PM

2

WARNING• Never modify this unit by removing any of the safety guards or bypassing any of

the safety interlock switches.• Do not install in a place which cannot bear the weight of the unit. Personal injury and property damage can result if the unit falls.• Before doing the electrical work, attach an approved plug to the power supply

cord. Also, make sure the equipment is properly earthed.• Appliance shall be installed in accordance with national wiring regulations. If you detect any damage, do not install the unit. Contact your dealer

immediately.

DANGER• FOR USE BY QUALIFIED PERSONS ONLY.• TURN OFF MAIN POWER SUPPLY BEFORE ATTEMPTING ANY ELECTRICAL

WORK. MAKE SURE ALL POWER SWITCHES ARE OFF. FAILURE TO DO SO MAY CAUSE ELECTRIC SHOCK.• CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING

CABLE IS CONNECTED WRONGLY, ELECTRIC PARTS MAY BE DAMAGED.• CHECK THE EARTH WIRE THAT IT IS NOT BROKEN OR DISCONNECTED

BEFORE INSTALLATION.• DO NOT INSTALL NEAR CONCENTRATIONS OF COMBUSTIBLE GAS OR

GAS VAPORS. FAILURE TO FOLLOW THIS INSTRUCTION CAN RESULT IN FIRE OR

EXPLOSION.• TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE

HAZARD, PLACE THE UNIT WELL AWAY (MORE THAN 2 M) FROM HEAT SOURCES SUCH AS RADIATORS, HEATERS, FURNACE, STOVES, ETC.

• WHEN MOVING THE AIR CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY CAREFUL NOT TO GET THE SPECIFIED REFRIGERANT (R32) WITH ANY OTHER GASEOUS BODY INTO THE REFRIGERATION CYCLE. IF AIR OR ANY OTHER GAS IS MIXED IN THE REFRIGERANT, THE GAS PRESSURE IN THE REFRIGERATION CYCLE BECOMES ABNORMALLY HIGH AND IT RESULTINGLY CAUSES BURST OF THE PIPE AND INJURIES ON PERSONS.

• IN THE EVENT THAT THE REFRIGERANT GAS LEAKS OUT OF THE PIPE DURING THE INSTALLATION WORK, IMMEDIATELY LET FRESH AIR INTO THE ROOM. IF THE REFRIGERANT GAS IS HEATED BY FIRE OR SOMETHING ELSE, IT CAUSES GENERATION OF POISONOUS GAS.


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI3

• Do not use any refrigerant different from the one specifi ed for complement or replacement.

Otherwise, abnormally high pressure may be generated in the refrigeration cycle, which may result in a failure or explosion of the product or an injury to your body.

• Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources (for example: open fl ames, an operating gas appliance or an operating electric heater).

• Be aware that refrigerants may not contain an odour.• Do not pierce or burn as the appliance is pressurized. Do not expose the

appliance to heat, fl ame, sparks, or other sources or ignition. Else, it may explode and cause injury or death.

• For R32 model, use pipes, fl are nut and tools which is specifi ed for R32 refrigerant. Using of existing (R22) piping, fl are nut and tools may cause abnormally high pressure in the refrigerant cycle (piping), and possibly result in explosion and injury.

• Thickness of copper pipes used R32 must be more than 0.8 mm. Never use copper pipes thinner than 0.8 mm.

• After completion of installation or service, confi rm there is no leakage of refrigerant gas. It may generate toxic gas when the refrigerant contacts with fi re.

• Appliance and pipe-work shall be installed, operated and stored in a room with a fl oor area larger than Amin m

2. How to get Amin m

2 : Amin = (M / (2.5 x 0.22759 x h0))2

M is the refrigerant charge amount in appliance in kg. h0 is the installation height of the appliance in m: 0.6 m for fl oor standing/1.8 m for wall mounted/1.0 m for window mounted/2.2 m for ceiling mounted (For these units recommend installation height 2.5 m.).

• Comply with national gas regulations.


4

REQUIREMENT OF REPORT TO THE LOCAL POWER SUPPLIERPlease make absolutely sure that the installation of this appliance is reported to the local power supplier before installation. If you experience any problems or if the installation is not accepted by the supplier, the service agency will take adequate countermeasures.

■ Important information regarding the refrigerant used This product contains fl uorinated greenhouse gases. Do not vent gases into the atmosphere. Refrigerant type: R32 GWP(1) value: 675 * (ex. R32 ref. AR4) (1)GWP = global warming potential The refrigerant quantity is indicated on the unit name plate. * This value is based on F gas regulation 517/2014

CAUTION• Exposure of unit to water or other moisture before installation could result in

electric shock. Do not store it in a wet basement or expose to rain or water.• After unpacking the unit, examine it carefully for possible damage.• Do not install the unit at place where leakage of fl ammable gas may occur. In

case gas leaks and accumulates at surrounding of the unit, it may cause of fi re.• Do not install in a place that can increase the vibration of the unit. Do not

install in a place that can amplify the noise level of the unit or where noise and discharged air might disturb neighbors.

• To avoid personal injury, be careful when handling parts with sharp edges.• Please read this installation manual carefully before installing the unit. It contains

further important instructions for proper installation.• The manufacturer shall not assume any liability for the damage caused by not

observing the description of this manual.


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI5

ACCESSORY PARTSACCESSORY PARTS

Indoor Unit

No. Part name No. Part name

1

Installation Plate × 1

2

Wireless remote control × 1

3

Battery × 24

Remote control holder × 1

5

Toshiba new IAQ fi lter × 16

Mounting screw × 6

7

Flat head wood screw × 2

8

Owner’s Manual × 1

9

Installation Manual × 1

!

Flat head wood screw × 1

"

Battery cover

Outdoor Unit

No. Part name No. Part name

#

Drain nipple × 1

$

Cap water proof × 2

Air fi ltersClean every 2 weeks. 1. Open the air inlet grille. 2. Remove the air fi lters. 3. Vacuum or wash and then dry them. 4. Reinstall the air fi lters and close the air inlet grille.

FilterMaintenance & Shelf-lifeClean every 3-6 months when dust tuck or covers the fi lter. 1. Recommend to use vacuum to clean by sucking the dusts which stick or dip inside the fi lter or use the blower to blow the dust go out through the fi lter. 2. If necessary to use water to clean, simply use the plain water to wash the fi lter, dry with the sunlight for 3-4 hours or until it completely dry. Nevertheless, use hair drier to dry it. However, washing with water, it may reduce the performance of the fi lter. 3. Replace every 2 years or sooner. (contact your dealer to purchase new fi lter) (P/N : RB-A620DE)Note: Filter life depends on the level of impurities in your operating environment. Higher levels of impurities may require more frequent cleaning and

replacement. In all cases, we recommend an additional set of fi lters to improve the purifying and deodorizing performance of your air conditioner.

Filter


6

INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITSINSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS

Partcode Parts name Q’ty

A

Refrigerant pipingLiquid side : Ø6.35 mmGas side : Ø9.52 mm (RAS-B10, 13PKVSG-E) : Ø12.70 mm (RAS-B16PKVSG-E)

Oneeach

BPipe insulating material(polyethylene foam, 6 mm thick) 1

C Putty, PVC tapes Oneeach

Optional Installation Parts• Secure the outdoor unit with fi xing bolts and nuts if the unit is likely to be

exposed to a strong wind.• Use Ø8 mm or Ø10 mm anchor bolts and nuts.• If it is necessary to drain the defrost water, attach drain nipple # and cap

water proof $ to the bottom plate of the outdoor unit before installing it.

Fixing bolt arrangement of outdoor unit

2

3

The auxiliary piping can be connected to the left, rear left, rear right, right, bottom right or bottom left.

Right

Rear right

Bottomright

Rearleft Bottom left

Left

Insulate the refrigerant pipes separately with insulation, not together.

6 mm thick heat resistingpolyethylene foam

1

Batteries

7Flat headwood screw

4Remote control holder

Vinyl tapeApply after carryingout a drainage test.

Wireless remote control Saddle

Extension drain hose(Not available, provided by installer)

Shield pipe

(Attach to the front panel.)

Air fi lter

Hook

Installationplate

Hook

65 m

m o

r mor

e

300 mm or more

300 mm or more

600

mm

or m

ore

100 mm or more

100 mm or more

600 mm or more

600 mm or more

Drain outlet

Air inlet

Air outlet

108 mm28 mm

600 mm

320

mm

125 mm

86 m

m

102

mm

90 mm

Ø25 m

m

Make sure to run the drain hose sloped downward.

Do not allow the drain hose to get slack.

Cut the piping hole sloped slightly.

Refrigerant piping must be protected from physical damage.Install a plastic cover or equivalent.

The provided Remote Controller is a wireless type, which also can be used as a wire.Please see “How to Connect The Remote Controller for Wired Operation”, in case of wired control is required.

5Filter

!Flat headwood screw

7

Flat headwood screw

"

Battery cover

w When using a multi-system outdoor unit, refer to the installation manual provided with the model concerned.

Cut out a piece of SPACER from indoorunit packaging box, roll it and insertbetween the indoor unit and wall to tiltthe indoor unit for better operation.

For the rear left, bottom left and left piping

Wall

340

mm


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI7

6

INDOOR UNITINDOOR UNIT

Installation Place

• Direct sunlight to the indoor unit’s wireless receiver should be avoided.• The microprocessor in the indoor unit should not be too close to RF

noise sources. (For details, see the owner’s manual.)

Remote control• A place where there are no obstacles such as a curtain that may block the

signal from the indoor unit• Do not install the remote control in a place exposed to direct sunlight or

close to a heating source such as a stove.• Keep the remote control at least 1 m apart from the nearest TV set or

stereo equipment. (This is necessary to prevent image disturbances or noise interference.)

• The location of the remote control should be determined as shown below.

Cutting a Hole and MountingInstallation Plate

NOTE• When drilling a wall that contains a metal lath, wire lath or metal plate, be sure

to use a pipe hole brim ring sold separately.

Cutting a holeWhen installing the refrigerant pipes from the rear

Mounting the installation plate

When the installation plate is directly mounted on the wall

1. Securely fi t the installation plate onto the wall by screwing it in the upper and lower parts to hook up the indoor unit.

2. To mount the installation plate on a concrete wall with anchor bolts, use the anchor bolt holes as illustrated in the below fi gure.

3. Install the installation plate horizontally in the wall.

When installing the installation plate with a mounting screw, do not use the anchor bolt holes. Otherwise, the unit may fall down and result in personal injury and property damage.

1. After determining the pipe hole position on the mounting plate ( ), drill the pipe hole (Ø65 mm) at a slight downward slant to the outdoor side.

• A place which provides the spaces around the indoor unit as shown in the diagram

• A place where there are no obstacles near the air inlet and outlet• A place which allows easy installation of the piping to the outdoor unit• A place which allows the front panel to be opened• The indoor unit shall be installed at least 2.5 m height. Also, it must be

avoided to put anything on the top of the indoor unit.

CAUTION

54 ° 45°

57°

(Side view) (Top view)

Indoor unit

Reception rangeRemote control

Remotecontrol

Receptionrange

Indo

or u

nit

CAUTION

Failure to fi rmly install the unit may result in personal injury and property damage if the unit falls.

• In case of block, brick, concrete or similar type walls, make 5 mm dia. holes in the wall.

• Insert clip anchors for appropriate mounting screws 6.

NOTE• Secure four corners and lower parts of the installation plate with 4 to 6

mounting screws to install it.

CAUTION

The center of the pipe hole is above the arrow.

Pipe hole

Ø65 mm

120 mm

Installation plate(Keep horizontal direction.)

5 mm dia. hole

Clip anchor(local parts)

Mounting screwØ4 mm x 25R

Anchor bolt

Projection15 mm or less

144

5050

300

65 103

300

6

1

Hook

Hook HookPipe holePipe hole

Installationplate

Mounting screwWeightIndoor unitThread

1 Open two screw caps and securely remove two screws at the front panel.2. Slightly open the lower part of the front panel then pull the upper part of

the front panel toward you to remove it as shown on fi gure 1.3. Arrange the control wire as detail and specifi cation as shown on fi gure

2.4. Securely connect the control wire to terminal of Display unit as shown on

fi gure 3 (tighten fi rmly but not over 0.12 N·m (0.01 kgf·m)).5. Set the control wire out from indoor unit same portion as power supply

and connecting cable as shown on fi gure 3. (Notch for wire out)6. Reassembly the indoor unit by reverse process of 1 to 2.

Indoor unit

Control wire

Remote controller

How to Connect Remote Controller for Wire Operation

For indoor unit


8

Piping and Drain Hose Installation

* Since dewing results in a machine trouble, make sure to insulate both connecting pipes. (Use polyethylene foam as insulating material.)

Piping and drain hose forming

1. Die-cutting back body slit Cut out the slit on the left or right side of the back body for the left or right

connection and the slit on the bottom left or right side of the back body for the bottom left or right connection with a pair of nippers.

Rear right

Rear left

Bottom left

Left

Bottom right

Right

Die

-cut

ting

back

bod

y sl

it Cha

ngin

gdr

ain

hose

Pip

ing

prep

arat

ion

2. Changing drain hose For leftward connection, bottom-leftward connection and rearleftward

connection’s piping, it is necessary to change the drain hose and drain cap.

1. Remove cover of remote controller by sliding down and take it out. 2. If batteries are exist, please take them out. The combination of using

wire controller and batteries may cause of batteries explosion. 3. Make hole for insert control wire by use screwdriver break the polyester

sheet as shown on fi gure 4. 4. Insert control wire from rear side of remote controller as shown on

fi gure 5. 5. Fix control wire which arrange as shown on fi gure 6 and 7 to terminal

by provided screws (tighten fi rmly but not over 0.25 N·m (0.03 kgf·m)). 6. Set control wire through gutter way at rear side of remote controller as

shown on fi gure 8. 7. Fix provided screw (Ø3.1×16L) on the wall to hang remote controller as

shown on fi gure 9. 8. Mark and arrange hole for fi x below screw (Ø3.1×25L) as shown on

fi gure 9. 9. Assembly battery cover which provided with accessory bag then use

provide screw (Ø3.1×25L) to fi x battery cover together with wall as shown on fi gure ! (tighten fi rmly but not over 0.15 N·m (0.02 kgf·m)).

10. Reassembly cover of remote controller.

For remote controller

*Remark : 1. Recommend to use double insulation lead wire for connect remote control and air conditioner.

2. For wire operation, 1 remote control can control only 1 indoor unit.

3. In wire operation, remote controller will return to initial condition (PRESET, TIMER and CLOCK will return to initial condition) when user shutdown power supply of air conditioner.

2

3

* Wire size 28-22AWG or 0.08-0.32 mm2

Outer diameter not over 4.7 mm, control wire length 30 m. or less.

70 mm

5 mm

Terminal

Control wireNotch for wire out

Control wire

Display unit

1

Screw

Screw cap

Screw

Front panel

Control wire

Hole for hangremote controller

Remote controller

Control wire

Screw (Ø3.1×16L) for hang remote controller

Wall

Screw (Ø3.1×25L) for fi x battery cover

Remote controller

8 9

!

Battery coverScrew

Tighten fi rmly but not over 0.15 N·m (0.02 kgf·m)

4 5

Polyester sheet close hole for insert control wire

Control wire

6

7

Control wire

Terminal

* Wire size 28-22AWG or 0.08-0.32 mm2

Outer diameter not over 4.7 mm, control wire length 30 m. or less.

30 mm

10 mm

* Terminals for wiring can be either on right (type A) or left (type B), depending on the controller packed in carton.

Type A Type B


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI9

How to remove the drain capClip the drain cap by needle-nose pliers and pull out.

How to remove the drain hose• The drain hose can be removed by removing the

screw securing the drain hose and then pulling out the drain hose.

• When removing the drain hose, be careful of any sharp edges of steel plate. The edges can injuries.

• To install the drain hose, insert the drain hose fi rmly until the connection part contacts with heat insulator, and then secure it with original screw.

How to fi x the drain cap1) Insert hexagon wrench (4 mm) in a center head.

2) Firmly insert the drain cap.

Firmly insert the drain hose and drain cap; otherwise, water may leak.

CAUTION

Drain hose

Left-hand connection with piping• Bend the connecting pipe so that it is laid within 43 mm above the wall

surface. If the connecting pipe is laid exceeding 43 mm above the wall surface, the indoor unit may unstably be set on the wall.

When bending the connecting pipe, make sure to use a spring bender so as not to crush the pipe.

Bend the connecting pipe within a radius of 30 mm.To connect the pipe after installation of the unit (fi gure)

80

260 mm

210 mm

43 m

m

Liquid side

Gas side

(To the forefront of fl are)

Outward form of indoor unit

R 30 mm (Use polisin (polyethylene)core or the like for bending pipe.)

Use the handle of screwdriver, etc.

NOTEIf the pipe is bent incorrectly, the indoor unit may unstably be set on the wall.After passing the connecting pipe through the pipe hole, connect the connecting pipes to the auxiliary pipes and wrap the facing tape around them.

In case of right or left piping• After scribing slits of the back body

with a knife or a making-off pin, cut them with a pair of nippers or an equivalent tool.

In case of bottom right or bottom left piping• After scribing slits of the back body

with a knife or a making-off pin, cut them with a pair of nippers or an equivalent tool.

Slit

Slit

CAUTION• Bind the auxiliary pipes (two) and connecting cable with facing tape

tightly. In case of leftward piping and rear-leftward piping, bind the auxiliary pipes (two) only with facing tape.

Indoor unit

Connecting cableAuxiliary pipes

Installation plate

• Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit.

• Carefully connect the auxiliary pipes and connecting pipes to one another and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint; moreover, seal the joint with the vinyl tape, etc.

• Since dewing results in a machine trouble, make sure to insulate both connecting pipes. (Use polyethylene foam as insulating material.)

• When bending a pipe, carefully do it, not to crush it.

Do not form thedrain hose intoa wavy shape.

Do not rise thedrain hose.

50 mmor more

Do not put thedrain hose endinto water.

Do not put thedrain hose endin the drainage ditch.

1

Hook here.

Installation plate

Hook Press(unhook)

PushPush

Indoor Unit Fixing

• For detaching the indoor unit from the installation plate, pull the indoor unit toward you while pushing its bottom up at the specifi ed parts.

1. Pass the pipe through the hole in the wall and hook the indoor unit on the installation plate at the upper hook.

2. Swing the indoor unit to right and left to confi rm that it is fi rmly hooked up on the installation plate.

3. While pressing the indoor unit onto the wall, hook it at the lower part on the installation plate. Pull the indoor unit toward you to confi rm that it is fi rmly hooked up on the installation plate.

Drainage1. Run the drain hose sloped downwards.

NOTE• The hole should be made at a slight downward slant on the outdoor side.

Do not apply lubricating oil(refrigerant machine oil) when inserting the drain cap. Application causes deterioration and drainleakage of the plug.

Insert a hexagon wrench (4 mm).

No gap


10

Drainguide

Space for pipes

Wall

Shield pipe

Inside the roomDrain hose Extension drain hose

Arrange the drain pipe for proper drainage from the unit.Improper drainage can result in dew-dropping.

This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide.

CAUTION

OUTDOOR UNITOUTDOOR UNIT

Installation Place• A place which provides the spaces around the outdoor unit as shown in

the diagram• A place which can bear the weight of the outdoor unit and does not allow

an increase in noise level and vibration• A place where the operation noise and discharged air do not disturb your

neighbors• A place which is not exposed to a strong wind• A place free of a leakage of combustible gases• A place which does not block a passage• When the outdoor unit is to be installed in an elevated position, be sure to

secure its feet.• The allowable length of the connecting pipe.

Models RAS-10PAVSG-E RAS-13PAVSG-E RAS-16PAVSG-EChargeless Less than 15 m Less than 15 m Less than 15 m

Maximum length 20 m 20 m 20 m

Additional refrigerant charging

16 - 20 m (20 g / 1 m)

16 - 20 m (20 g / 1 m)

16 - 20 m (20 g / 1 m)

• The allowable height of outdoor unit installation site.

Models RAS-10PAVSG-E RAS-13PAVSG-E RAS-16PAVSG-EMaximum height 12 m 12 m 12 m

• A place where the drain water does not raise any problems

CAUTION1. Install the outdoor unit without anything blocking the air discharging.2. When the outdoor unit is installed in a place always exposed to strong

wind like a coast or on a high storey of a building, secure the normal fan operation using a duct or a windshield.

3. In particularly windy areas, install the unit such as to avoid admission of wind.

4. Installation in the following places may result in trouble. Do not install the unit in such places. • A place full of machine oil • A saline-place such as the coast • A place full of sulfi de gas • A place where high-frequency

waves are likely to be generated as from audio equipment, welders, and medical equipment

Strong wind

• Do not use the supplied drain nipple for draining water. Drain the water from all the drain holes directly.

• To protect the outdoor unit from snow accumulation, install a holding frame, and attach a snow protection hood and plate.

* Do not use a double-stacked design.

Precautions about Installation in Regionswith Snowfall and Cold Temperatures

Snow protection plate

Snow protection hood

Snow accumulation line

Holding frame

At least50 cm

Install at least 50 cmabove the snowaccumulation line.

Anchorbolts

Front

2. Put water in the drain pan and make sure that the water is drained out of doors.

3. When connecting extension drain hose, insulate the connecting part of extension drain hose with shield pipe.

90 Obliquity Roughness Warp

Refrigerant Piping Connection

1. Cut the pipe with a pipe cutter.

2. Insert a fl are nut into the pipe and fl are the pipe. • Projection margin in fl aring : A (Unit : mm)RIDGID (clutch type)

IMPERIAL (wing nut type)

Outer dia. of copper pipe R32Ø6.35 1.5 to 2.0Ø9.52 1.5 to 2.0

Ø12.70 2.0 to 2.5Pipes thickness 0.8 mm or more

Outer dia.of copper pipe R32 tool used Conventional tool

usedØ6.35 0 to 0.5 1.0 to 1.5Ø9.52 0 to 0.5 1.0 to 1.5Ø12.70 0 to 0.5 1.0 to 1.5

Pipes thickness 0.8 mm or more

Flaring

A

Die Pipe

CAUTION• Do not scratch the inner surface of the fl ared part when removing

burrs. • Flare processing under the condition of scratches on the inner surface

of fl are processing part will cause refrigerant gas leak.


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI11

Flare nutHalf union

Externallythreaded side

Internallythreaded side

Use a wrench to secure. Use a torque wrench to tighten.

CAUTION

Align the centers of the connecting pipes and tighten the fl are nut as far as pos-sible with your fi ngers. Then tighten the nut with a spanner and torque wrench as shown in the fi gure.

Tightening connection

Do not apply excess torque. Otherwise, the nut may crack depending on the conditions.

(Unit : N·m)

Outer dia. of copper pipe Tightening torqueØ6.35 mm 16 to 18 (1.6 to 1.8 kgf·m)Ø9.52 mm 30 to 42 (3.0 to 4.2 kgf·m)Ø12.70 mm 50 to 62 (5.0 to 6.2 kgf·m)

Flare at indoor unit side

Flare atoutdoor unit side

• Tightening torque of fl are pipe connections The operating pressure of R32 is

higher than that of R22 (approx. 1.6 times). It is therefore necessary to fi rmly tighten the fl are pipe connecting sections (which connect the indoor and outdoor units) up to the specifi ed tightening torque. Incorrect connections may cause not only a gas leakage, but also damage to the refrigeration cycle.

EvacuatingAfter the piping has been connected to the indoor unit, you can perform the air purge together at once.

AIR PURGEEvacuate the air in the connecting pipes and in the indoor unit using a vacuum pump. Do not use the refrigerant in the outdoor unit. For details, see the manual of the vacuum pump.

Be sure to use a vacuum pump with counter-fl ow prevention function so that inside oil of the pump does not fl ow backward into pipes of the air conditioner when the pump stops.(If oil inside of the vacuum pump enters the air conditioner, which use R32, refrigeration cycle trouble may result.)1. Connect the charge hose from the manifold valve to the service port of the

packed valve at gas side.2. Connect the charge hose to the port of the vacuum pump.3. Open fully the low pressure side handle of the gauge manifold valve.4. Operate the vacuum pump to start evacuating. Perform evacuating for

about 15 minutes if the piping length is 20 meters. (15 minutes for 20 meters) (assuming a pump capacity of 27 liters per minute) Then confi rm that the compound pressure gauge reading is –101 kPa (–76 cmHg).

5. Close the low pressure side valve handle of the gauge manifold valve.6. Open fully the valve stem of the packed valves (both gas and liquid sides).7. Remove the charging hose from the service port.8. Securely tighten the caps on the packed valves.

Using a vacuum pump

Packed valve at liquid side

Service port (Valve core (Setting pin))Packed valve at gas side

Vacuumpump

Vacuum pump adapter forcounter-fl ow prevention

Charge hose

Handle Hi(Keep full closed)

Manifold valve

Pressure gaugeCompound pressure gauge

Handle Lo

Charge hose

Connecting pipe

–101 kPa(–76 cmHg)

CAUTION• KEEP IMPORTANT 6 POINTS FOR PIPING WORK. (1) Take away dust and moisture (inside of the connecting pipes). (2) Tighten the connections (between pipes and unit). (3) Evacuate the air in the connecting pipes using a VACUUM PUMP. (4) Check gas leak (connected points). (5) Be sure to fully open the packed valves before operation. (6) Reusable mechanical connectors and fl ared joints are not allowed

indoors. When mechanical connectors are reused indoors, sealing parts shall be renewed. When fl ared joints are reused indoors, the fl are part shall be refabricated.

Packed valve handling precautions• Open the valve stem all the way out, but do not try to open it beyond the

stopper.

• Securely tighten the valve cap with torque in the following table:

Pipe size of Packed Valve Size of Hexagon wrench

12.70 mm and smallers A = 4 mm

15.88 mm A = 5 mm

Cap Cap Size (H) Torque

Valve Rod CapH17 - H19 14~18 N·m

(1.4 to 1.8 kgf·m)

H22 - H30 33~42 N·m(3.3 to 4.2 kgf·m)

Service Port CapH14 8~12 N·m

(0.8 to 1.2 kgf·m)

H17 14~18 N·m(1.4 to 1.8 kgf·m)

A

H

Hexagon wrenchis required.

Service Port Cap

Valve Rod Cap


12

ELECTRICAL WORKSELECTRICAL WORKS

Indoor unit Outdoor unit

Valve cover

Terminals block

How to install the air inlet grille on the indoor unit

• When attaching the air inlet grille, the contrary of the removed operation is performed.

Wiring of the connecting cable can be carried out without removing the front panel.1. Remove the air inlet grille. Open the air inlet grille upward and pull it toward you.2. Remove the terminal cover and cord clamp.3. Insert the connecting cable (according to the local cords) into the pipe hole

on the wall.4. Take out the connecting cable through the cable slot on the rear panel so

that it protrudes about 20 cm from the front.5. Insert the connecting cable fully into the terminal block and secure it tightly

with screws.6. Tightening torque : 1.2 N·m (0.12 kgf·m)7. Secure the connecting cable with the cord clamp.8. Fix the terminal cover, rear plate bushing and air inlet grille on the indoor

unit.

Cord clamp

Terminal cover

Screw

Screws

Air inlet grille

Front panel

1. Remove the valve cover, the electric parts cover and the cord clamp from the outdoor unit.

2. Connect the connecting cable to the terminal as identifi ed by the matching numbers on the terminal block of indoor and outdoor unit.

3. Insert the power cord and the connecting cable carefully into the terminal block and secure it tightly with screws.

4. Use vinyl tape, etc. to insulate the cords which are not going to be used. Locate them so that they do not touch any electrical or metal parts.

5. Secure the power cord and the connecting cable with the cord clamp.6. Attach the electric parts cover and the valve cover on the outdoor unit.

Model RAS-B10PKVSG-E RAS-B13PKVSG-E RAS-B16PKVSG-EPower source 50Hz, 220 – 240 V Single phase

Maximum running current 6.75A 7.35A 8.95A

Circuit breaker rating 8.5A 9.5A 11.5A

Power supply cableH07RN-F or 60245 IEC66 (1.5 mm2 or more)

Connecting cable


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI13

Power Supply Input at Indoor Unit Terminal Block (Recommend)

Indoor Unit Outdoor Unit

Power supply cableconnect to L N

Terminal block (L N 1 2 3)

Earth line

Power supplycable

Power supply cable Stripping length of the power supply cable

N

L

Earth line50 mm

10 mm

70 mm10 mm

Connecting cable

Earth lineConnecting cable

Terminal block

Connecting cableconnect to 1 2 3


Earth line

Power supply cable

Connecting cable

Earth line

Connecting cable Stripping length of the connecting cable

3

50 mmEarth line

10 mm

70 mm10 mm

Power Supply Input at Outdoor Unit Terminal Block (Optional)


Connecting cableconnect to L 2 3


Earth line

Connecting cable

Connecting cable Stripping length of the connecting cable

32L

Earth line50 mm

10 mm

70 mm10 mm

Connecting cable

Earth line Earth line

Connecting cable Power cord

Terminal block

Power cord

In Case of Indoor Unit Connect With 1:1 Outdoor Unit


14

CAUTION1. The power supply must be same as the rated of air conditioner.2. Prepare the power source for exclusive use with air conditioner.3. Circuit breaker must be used for the power supply line of this air conditioner.4. Be sure to comply power supply and connecting cable for size and wiring method.5. Every wire must be connected fi rmly.6. Perform wiring works so as to allow a general wiring capacity.7. Wrong wiring connection may cause some electrical part burn out.8. Incorrect or incomplete wiring is carried out, it will cause an ignition or smoke.9. This product can be connected to main power supply. Connection to fi xed wiring : A switch which disconnects all poles and has a contact separation at least 3 mm must be incorporated in the fi xed wiring.

Power supply input Wiring Diagram for 1:1 Outdoor Unit

Power input at Indoor Terminal Block (Recommend)

Indoor Terminal Block

Power input

Outdoor Terminal Block

Chassis

Chassis

Power input at Outdoor Terminal Block (Optional)


Power input


Chassis

Chassis


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI15

Power Supply Input at Outdoor Unit Terminal Block


Connecting cableconnect to L 2 3


Earth line

Connecting cable

Connecting cable Stripping length of the Connecting cable

32L

Earth line50 mm

10 mm

70 mm10 mm

1(L)

Power cord

Earth lineEarth line

Connecting cable

Terminal block

Power cordConnecting cable

Power supply input Wiring Diagram for Inverter Multi System (IMS)

In Case of Indoor Unit Connect With Inverter Multi System (IMS)

CAUTION1. The power supply must be same as the rated of air conditioner.2. Prepare the power source for exclusive use with air conditioner.3. Circuit breaker must be used for the power supply line of this air conditioner.4. Be sure to comply power supply and connecting cable for size and wiring method.5. Every wire must be connected fi rmly.6. Perform wiring works so as to allow a general wiring capacity.7. Wrong wiring connection may cause some electrical part burn out.8. Incorrect or incomplete wiring is carried out, it will cause an ignition or smoke.9. This product can be connected to main power supply. Connection to fi xed wiring : A switch which disconnects all poles and has a contact separation at least 3 mm must be incorporated in the fi xed wiring.

Power input at Outdoor Terminal Block


Power input


Chassis

Chassis


16

OTHERSOTHERS

Gas Leak Test

Remote Control A-B Selection

To separate using of remote control for each indoor unit in case of 2 air conditioner are installed near.Remote Control B Setup.1. Press [RESET] button on the indoor unit to turn the air conditioner ON.2. Point the remote control at the indoor unit.3. Push and hold [CHECK] button on the Remote Control by the tip of the

pencil. “00” will be shown on the display (Picture 1).4. Press [MODE] during pushing [CHECK]. “B” will show on the display

and “00” will disappear and the air conditioner will turn OFF. The Remote Control B is memorized (Picture 2).

Note : 1. Repeat above step to reset Remote Control to be A. 2. Remote Control A have not “A” display. 3. Default setting of Remote Control from factory is A.

• Check the fl are nut connections for the gas leak with a gas leak detector or soap water.

Check places forthe indoor unit.

Check places forthe outdoor unit.

• When two indoor units are installed in the same room or adjacent two rooms, if operating a unit, two units may receive the remote control signal simultaneously and operate. In this case, the operation can be preserved by setting either one remote control to B setting. (Both are set to A setting in factory shipment.)

• The remote control signal is not received when the settings of indoor unit and remote control are different.

• There is no relation between A setting/B setting and A room/B room when connecting the piping and cables.

1 2

Test Operation

To switch the TEST RUN (COOL) mode, press [RESET] button for 10 seconds. (The beeper will make a short beep.)

Auto Restart Setting

The product was shipped with Auto Restart function in the off position. Turn it on as required.

This product is designed so that, after a power failure, it can restart automatically in the same operating mode as before the power failure.

Information

How to set the Auto Restart1. Press and hold the [RESET] button on the indoor unit for 3 seconds to

set the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)

2. Press and hold the [RESET] button on the indoor unit for 3 seconds to cancel the operation. (3 beep sound but OPERATION lamp does not blink)

• In case of ON timer or OFF timer are set, AUTO RESTART OPERATION does not activate.

OPERATION / RESET Button


EN

ES

FR

IT

DE

PT

PL

CZ

RU

CR

HU

TR

NL

GR

SV

FI

NO

DK

RO

BG

EE

LV

SK

SI17

AP

PE

ND

IXA

PP

EN

DIX

Wor

k in

stru

ctio

nsTh

e ex

istin

g R

22 a

nd R

410A

pip

ing

can

be re

used

for

inve

rter R

32 p

rodu

ct in

stal

latio

ns.

WA

RN

ING

Con

firm

ing

the

exis

tenc

e of

scr

atch

es o

r den

ts o

nth

e ex

istin

g pi

pes

and

confi

rmin

g th

e re

liabi

lity

ofth

e pi

pe s

tren

gth

are

conv

entio

nally

refe

rred

to th

elo

cal s

ite.

If th

e sp

ecifi

ed c

ondi

tions

can

be

clea

red,

it is

poss

ible

to u

pdat

e ex

istin

g R

22 a

nd R

410A

pip

esto

thos

e fo

r R32

mod

els.

Bas

ic c

ondi

tions

nee

ded

to re

use

exis

ting

pipe

sC

heck

and

obs

erve

the

pres

ence

of t

hree

con

ditio

ns in

the

refri

gera

nt p

ipin

g w

orks

.1.

Dry

(The

re is

no

moi

stur

e in

side

of t

he p

ipes

.)2.

Cle

an (T

here

is n

o du

st in

side

of t

he p

ipes

.)3.

Tig

ht (T

here

are

no

refri

gera

nt le

aks.

)

Res

tric

tions

for u

se o

f exi

stin

g pi

pes

In th

e fo

llow

ing

case

s, th

e ex

istin

g pi

pes

shou

ldno

t be

reus

ed a

s th

ey a

re. C

lean

the

exis

ting

pipe

sor

exc

hang

e th

em w

ith n

ew p

ipes

.1.

Whe

n a

scra

tch

or d

ent i

s he

avy,

be

sure

to u

se n

ew

pipe

s fo

r the

refri

gera

nt p

ipin

g w

orks

.2.

Whe

n th

e ex

istin

g pi

pe th

ickn

ess

is th

inne

r tha

n th

e sp

ecifi

ed “P

ipe

diam

eter

and

thic

knes

s,” b

e su

re to

us

e ne

w p

ipes

for t

he re

frige

rant

pip

ing

wor

ks.

The

ope

ratin

g pr

essu

re o

f R32

is h

igh

(1.6

tim

es

that

of R

22).

If th

ere

is a

scr

atch

or d

ent o

n th

e pi

pe

or a

thin

ner p

ipe

is u

sed,

the

pres

sure

stre

ngth

may

be

inad

equa

te, w

hich

may

cau

se th

e pi

pe to

bre

ak

in th

e w

orst

cas

e.*

Pipe

dia

met

er a

nd th

ickn

ess

(mm

)

Pip

e ou

ter d

iam

eter

Ø6.

4Ø

9.5

Ø12

.7

Thic

knes

sR

32, R

410A

0.8

0.8

0.8

R22

3. W

hen

the

outd

oor u

nit w

as le

ft w

ith th

e pi

pes

disc

onne

cted

, or t

he g

as le

aked

from

the

pipe

s an

d th

e pi

pes

wer

e no

t rep

aire

d an

d refil

led.

The

re is

the

poss

ibili

ty o

f rai

n w

ater

or a

ir, in

clud

ing

moi

stur

e, e

nter

ing

the

pipe

.4.

Whe

n re

frige

rant

can

not b

e re

cove

red

usin

g a

refri

gera

nt re

cove

ry u

nit.

The

re is

the

poss

ibili

ty th

at a

larg

e qu

antit

y of

dirt

y oi

l or m

oist

ure

rem

ains

insi

de th

e pi

pes.

5. W

hen

a co

mm

erci

ally

ava

ilabl

e dr

yer i

s at

tach

ed to

the

exis

ting

pipe

s. T

here

is th

e po

ssib

ility

that

cop

per g

reen

rust

has

be

en g

ener

ated

.6.

Whe

n th

e ex

istin

g ai

r con

ditio

ner i

s re

mov

ed a

fter

refri

gera

nt h

as b

een

reco

vere

d.

Che

ck if

the

oil i

s ju

dged

to b

e cl

early

diff

eren

t fro

m

norm

al o

il. T

he re

frige

rato

r oil

is c

oppe

r rus

t gre

en in

col

or:

Th

ere

is th

e po

ssib

ility

that

moi

stur

e ha

s m

ixed

with

th

e oi

l and

rust

has

bee

n ge

nera

ted

insi

de th

e pi

pe.

The

re is

dis

colo

red

oil,

a la

rge

quan

tity

of re

sidu

e,

or a

bad

sm

ell.

A la

rge

quan

tity

of s

hiny

met

al d

ust o

r oth

er w

ear

resi

due

can

be s

een

in th

e re

frige

rant

oil.

7. W

hen

the

air c

ondi

tione

r has

a h

isto

ry o

f the

co

mpr

esso

r fai

ling

and

bein

g re

plac

ed.

Whe

n di

scol

ored

oil,

a la

rge

quan

tity

of re

sidu

e,

shin

y m

etal

dus

t, or

oth

er w

ear r

esid

ue o

r mix

ture

of

fore

ign

mat

ter i

s ob

serv

ed, t

roub

le w

ill o

ccur

.8.

Whe

n te

mpo

rary

inst

alla

tion

and

rem

oval

of t

he a

ir co

nditi

oner

are

repe

ated

suc

h as

whe

n le

ased

etc

.9.

If t

he ty

pe o

f ref

riger

ator

oil

of th

e ex

istin

g ai

r co

nditi

oner

is o

ther

than

the

follo

win

g oi

l (M

iner

al o

il),

Sun

iso,

Fre

ol-S

, MS

(Syn

thet

ic o

il), a

lkyl

ben

zene

(H

AB

, Bar

rel-f

reez

e), e

ster

ser

ies,

PV

E o

nly

of e

ther

se

ries.

The

win

ding

-insu

latio

n of

the

com

pres

sor m

ay

dete

riora

te.

NO

TE

The

abov

e de

scrip

tions

are

resu

lts h

ave

been

con

firm

ed

by o

ur c

ompa

ny a

nd re

pres

ent o

ur v

iew

s on

our

air

cond

ition

ers,

but

do

not g

uara

ntee

the

use

of th

e ex

istin

g pi

pes

of a

ir co

nditi

oner

s th

at h

ave

adop

ted

R32

in o

ther

co

mpa

nies

.

Cur

ing

of p

ipes

Whe

n re

mov

ing

and

open

ing

the

indo

or o

r out

door

uni

t for

a

long

tim

e, c

ure

the

pipe

s as

follo

ws:

Oth

erw

ise

rust

may

be

gene

rate

d w

hen

moi

stur

e or

fo

reig

n m

atte

r due

to c

onde

nsat

ion

ente

rs th

e pi

pes.

The

rust

can

not b

e re

mov

ed b

y cl

eani

ng, a

nd n

ew

pipe

s ar

e ne

cess

ary.

Plac

emen

t lo

catio

nTe

rmC

urin

g m

anne

r

Out

door

s1

mon

th o

r mor

eP

inch

ing

Less

than

1 m

onth

Pin

chin

g or

tapi

ngIn

door

sE

very

tim

e

Are

ther

e sc

ratc

hes

or d

ents

on

the

exis

ting

pipe

s?

Is it

pos

sibl

e to

ope

rate

the

exis

ting

air c

ondi

tione

r?

Afte

r the

exi

stin

g ai

r con

ditio

ner i

s op

erat

ed in

coo

ling

mod

e fo

r app

rox.

30

min

utes

or l

onge

r,* re

cove

r the

re

frige

rant

. F

or c

lean

ing

the

pipe

s an

d re

cove

ring

oil

Ref

riger

ant r

ecov

ery:

Pum

p do

wn

met

hod

Rem

ove

the

exis

ting

air c

ondi

tione

r fro

m th

e pi

ping

an

d ca

rry

out fl

ushi

ng (n

itrog

en p

ress

ure

0.5

MP

a) to

re

mov

e an

y re

mai

ns in

side

of t

he p

ipe.

Not

e: I

n ca

se o

f tw

in p

ipes

, als

o be

sur

e to

flus

h th

e br

anch

ing

pipe

.

Con

nect

the

indo

or /

outd

oor u

nits

to th

e ex

istin

g pi

pe.

Use

a fl

are

nut a

ttach

ed to

the

mai

n un

it fo

r the

indo

or

/ out

door

uni

ts. (

Do

not u

se th

e fla

re n

ut o

f the

exi

stin

g pi

pe.)

Re-

mac

hine

the fla

re m

achi

ning

siz

e to

siz

e fo

r R32

.

(A

irtig

ht te

st),

Vacu

um d

ry, R

efrig

eran

t cha

rge,

Gas

le

ak c

heck

Test

run

Was

larg

ely

disc

olor

ed o

il or

a la

rge

quan

tity

of re

mai

ns d

isch

arge

d? (W

hen

the

oil d

eter

iora

tes,

th

e co

lor o

f the

oil

chan

ges

to a

mud

dy

or b

lack

col

or.)

Exi

stin

g pi

pes:

Can

not b

e us

ed.

Use

new

pip

es.

Cle

an th

e pi

pes

or u

se n

ew p

ipes

.

Pipi

ng n

eces

sary

to c

hang

e th

e fla

re n

ut /

mac

hini

ng

size

due

to p

ipe

com

pres

sion

1) F

lare

nut

wid

th: H

H

(mm

)C

oppe

r pip

e ou

ter d

iam

eter

Ø6.

4Ø

9.5

Ø12

.7

For R

32, R

410A

1722

26Fo

r R22

Sam

e as

abo

ve24

2) F

lare

mac

hini

ng s

ize:

A

A

(mm

)C

oppe

r pip

e ou

ter d

iam

eter

Ø6.

4Ø

9.5

Ø12

.7

For R

32, R

410A

9.1

13.2

16.6

For R

229.

013

.016

.2

Bec

omes

a li

ttle

larg

er fo

r R32

Do

not a

pply

refri

gera

tor o

il to

the fla

re s

urfa

ce.

(If th

ere

is d

isch

arge

of r

emai

ns, i

t is

judg

ed th

at a

la

rge

quan

tity

of re

mai

ns a

re p

rese

nt.)

YE

S

YE

S

NO

NO

NO

YE

S

Nitr

ogen

gas

pre

ssur

e 0.

5 M

Pa


1122950102-1

10_1122950102-1-Cover back.indd 510_1122950102-1-Cover back.indd 5 3/1/2562 BE 4:32 PM3/1/2562 BE 4:32 PM

installation manual (split type) english …...air conditioner (split type) installation manual...

Documents