installing sme version 5 –1)set the computer to boot from the cdrom by changing the bios setting....
TRANSCRIPT
Installing SME Version 5
– 1)Set the computer to boot from the CDRom by changing the BIOS setting.
– 2)Startup the computer with the CD in the CD drive
– 3)Type "accept" (without quotes) at the [boot:] prompt.
– 4)Press Enter
– 5)Wait…. For the "Welcome to the e-smith server and gateway" message and the "Service LINK License Agreement"
Install – Cont.
– 6)Tab to the "ACCEPT" choice and press Enter– 7)Select (up/down arrow) "Install using Single
Hard Drive (tab to choice)– 8)Tab to "OK" and press Enter– 9)Type "proceed" at the prompt – 10)Tab to the "OK" choice and press Enter– 11)Wait…. (for formatting, file transfer, etc.)
Install –Cont.– 12)When prompted to create a Boot Diskette,
insert a diskette in the drive and type press Enter to select "Yes"
– 13)Press Enter to select "OK"– 14)Press Enter and be ready to eject the CD. – 15)Remove the CD while the system is shutting
down.– 16)Remove the boot floppy.– 17)Wait… for the reboot process to complete.
Configuring the SME5 Server
– 1)When prompted for the admin password, type in a password, press Enter
– 2)Retype the password, press Enter– 3)Tab to "Yes" press Enter– 4)Enter a valid IP Address from your local
network for the domain name. – 5)Tab to "next" and press Enter
Configure –Cont.
– 6)Type in a server name (i.e. SME5, e-smith, etc.) tab to "Next", press Enter
– 7)Confirm that your Ethernet card has been detected. Press Enter to select.
– 8)Enter the IP Address you used for the domain name.
– 9)Tab to "Next" and press Enter
Configure –Cont.– 10)Enter the subnet mask for your network
(255.255.255.___)– 11)Tab to "Next" and press Enter– 12)Operation Mode: arrow down to option 3
(Server Only) , tab to "Next", Press Enter– 13)Gateway: Enter your gateway IP address
(router, Ethernet port, firewall, etc.) – 14)Tab to "Next" press Enter
Configure –Cont.
– 15)DHCP: OFF - Arrow down to OFF, tab to "Next" press Enter
– 16)DNS: Leave blank, tab to "Next" press Enter– 17)Proxy: NO - tab to "Next" press Enter– 18)Status to e-smith: NO press Enter– 19)Console: Login arrow down to login, tab to
"Next" press Enter
Configure – Cont.
– 20)Notify by email, press Enter– 21)Activate Configuration: YES press Enter– 22)Wait….. for reboot.– 23)Login: "admin" Enter– 24)Your password Enter– 25)Arrow down to "Test Internet Access" press
Enter
Configure –Cont.
– 26)Wait for "Success" or "Unsuccessful" message.
– 27)IF unsuccessful, check ethernet connection, card acceptability, IP gateway, IP of server.
– 28)Arrow down to Shutdown and select shutdown.
– 29)Power off.
UpDating the SME5 Server
(Currently, skip the next 2 slides for SME v5.1.2)
• Through a web browser enter your “IP address/server-manager” in the URL address space and press enter.– 111.222.33.44/server-manager
• Login as “admin”
• Enter your server password
Updating –Cont.
• Scroll down to “Administration” and click on the selection “Blades”
• Click “install” on the supported Blades– (You should install each supported Blade)
• Click “yes” to the license agreements• Wait for completion message.
– It will take a few minutes, be patient and only click once.