R

Phone: +1Fax: +1 (214) 565-0976Toll Free: +1 (800) 527-2100Website: www.apwwyott.comE-mail: info@apwwyott.com

(214) 421-7366

INSTALLATIONAND

OPERATING INSTRUCTIONS

INTENDED FOR OTHERTHAN HOUSEHOLD USE

RETAIN THIS MANUAL FOR FUTURE REFERENCEAPPLIANCE MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

P/N 70202001 3/06

1

CONTACT BUN TOASTER

APW WYOTT729 Third AvenueDallas, TX 75226

This equipment has been engineered to provide you with year-round dependable service when usedaccording to the instructions in thismanual and standard commercial kitchen practices.

Initial heating of appliance may generate smoke or fumes and must be done in a well ventilated area.Overexposure to smokeor fumesmay cause nausea or dizziness.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors andliquids in the vicinity of this or any other appliance. !!

WARNING: Improper installation, adjustment, alteration, service or maintenance cancause property damage, injury or death. Read the Installation, Operating andMaintenance Instructions thoroughly before installing or servicing this equipment.

!!

ANSI/NSF4

(800) 733-220324 Hour Service Hotline

Model: M2000-JIB

TABLE OF CONTENTS

Safety Precautions 2General Information 2Installation 3Location 4Operating Instructions 4Cleaning 5

Daily Parts Cleaning 5Daily Conveyor Cleaning 5One-Time Boil Out of Conveyor 6Daily Griddle Cleaning 6

Troubleshooting 8Specifications 9Replacement Parts List w/Exploded View 10Wiring Diagram 12Warranty 14

SAFETY PRECAUTIONS

GENERAL INFORMATION

APW Wyott toasters are designed, built, and sold for commercial use and should be operated by trainedpersonnel only. Clearly post all CAUTIONS, WARNINGS and operating instructions near each unit toinsureproper operationand to reduce the chanceof personal injury and/or equipment damage.

Always disconnect power before cleaning or servicing the toaster. Surfaceswill remain hot after power hasbeen turned off, allow unit to cool before cleaning or servicing. Never clean the toaster by immersing it inwater. The toaster is not protected against water jets; DO NOT CLEAN TOASTER WITH AWATER JET.Always cleanequipment before first use.

Operating toasterwithout legswill void thewarranty. Insureall accessoriesandexterior panels are properlyinstalled andadjustedbefore applyingpower andoperating.

Check the rating label for your model designation and electrical rating. Rating Label is located on thebottom front of the control panel.

Overall dimensionswith feeder: 23.5"(59.7cm)Wx25.9"(65.8cm)Hx17.5"(44.5cm)D

M2KA: 208VAC, 2880W, 13.8A60HzM2KH:240VAC, 3840W, 16A60Hz

208/250V:NEMA6-20PPlug, 4 foot, 3wire groundedcord.

If the supply cord is damaged, the manufacturer or an authorized service agent or a similarly qualifiedpersonmust replace it to avoid a hazardorwarranty.

94 lbs (42.7Kg)

ElectricalRatings:

CordsetConfiguration:

ShippingWeight:

2

INSTALLATION

1. Examine carton for damage

a. Apparent damage or loss must be noted on the freight bill at the time of delivery.must sign

b. Concealed damage or loss if not apparent until after the toaster is removed fromcarton,

Besure to saveall contents andpackagingmaterial.

2. VerifyParts

The freight carrier has assumed responsibility for its safe transit and delivery. If equipment isreceiveddamaged, either apparent or concealed, a claimmust bemadewith delivering carrier.

The carrier representative (Driver) the freight bill. If this is not done, thecarriermay refuse the claim.The carrier can supply the necessary forms.

a request for inspection must be made to the carrier within 15 days. The carriershould arrangean inspection.

After removing unit from the shipping carton, unwrapping loose parts and remove any packing tape,plasticwrapandnylon tie-down.Verify the followingparts:

Item Packaging Qty

NOTE:

3. AssembleLegs

Legs In plastic bag 4Feeder/Bun Chute Wrapped, loose in top of carton 1Conveyor In individual carton 1Instruction Manual Loose in carton 1Teflon Sheet Kit (optional) Loose in carton Optional

PRIORTO INITIALSTART-UP,ALLREMOVABLEPARTSANDTHEGRILLSURFACESHOULDBECLEANEDWITHWARMSOAPYWATERTOREMOVEMANUFACTURINGOILS,THENRINSEDAND DRIED THOROUGHLY.Apply oil (vegetable oil) to the conveyor chain after washing. (Bun oil can beused if it contains noanimal fats, salts or dairy products).

Lay the toaster on its back and install the four adjustable legs into the threaded holes on the bottomof the toaster sides. Hand tighten the legs by gripping the black shank and turning until it is seatedfirmly against the bottom of the toaster. Set the toaster upright on a flat surface. Unscrewing thelower, chrome insert of each leg levels the unit. Flats are provided on two sides of the insert to allowuseof awrench. �Precise� leveling is not required for proper operation.

FIGURE 1. M2000 ASSEMBLY DRAWING4. Conveyor InstallationRemove the front panel by lifting itstraight up. (See Figure 1) Liftconveyor assembly by using �U�shaped handles on each conveyorside bracket. Lower the conveyorinto the two conveyor hangerbrackets above the grill plate oneach side, so the four spacers onthe sides of the conveyor rest onthe bottom flange and the bottomspacers are against the adjustmentscrews. The conveyor hangerbrackets are factory adjusted.However, before reinstalling thefront panels apply power to the unitand run the conveyor to insureproper gear engagement. If gearsare not properly engaged, adjustthe conveyor by loosening the jamnuts on the conveyor hangerbrackets and adjusting the screw(seeFigure 2) to set the conveyor to

3

BottomFrontPanel

Top Front Panel

Feeder

ConveyorHanger

Main PowerSwitch

ConveyorAssembly

the correct height.Retighten lock nuts after adjustment is complete.a. To adjust the conveyor up into the drive gear, turn the conveyor adjustment screw

clockwise.Usea7/16-endwrench to tighten the jamnut.b. To adjust the conveyor away from the drive gear, turn the conveyor adjustment screw

counterclockwise.Usea7/16-endwrench to tighten the lock nut.

5. Replace frontpanel.

6. FeederAssembly

7. Install TeflonSheet (Optional)

Install Feeder by fitting slots on back of feederonto back panel studs located at top rear ofunit.

Remove Feeder. Allow one end of the Teflonsheet to overlap the top of the rear panel tothe rear studs. Align the holes in the sheetwith the stud heads and push the sheet overthe stud heads. Balance of the sheet will fitover the grill surface. Reinstall Feedercap t u r i n g Te f l o n Shee t be tweenthe feeder and the top of the toaster.

FIGURE 2

Jam Nut

Screw

LOCATION

OPERATING INSTRUCTIONS

Place the toaster on a flat surface. This toaster is tested and approved for zero clearances againstsurfaces. Locate the toaster near a wall receptacle of the proper configuration.

Plug the power cord into an outlet (receptacle) of the specified voltage on the ratinglabel.Outletsmust be properly grounded.

ChooseDry orWet operation.

(no oil) InsureTeflon sheet, 86298 is properly installed.a. Turn Main Power Switch on. Set Temperature Control knob to desired temperature. Allow Pilot

Light to cycle at least two times (on/off). When the light is on, the grill is heating. Heat up time isabout 15-20minutes.

b. Turn onmotor switch.Conveyor should start to turn.c. Place bun halves on feeder cut side down (facing grill surface). Toast time is approximately 210

sec. depending on bun height and diameter. Increase or decrease temperature setting toachievedesiredbrownnessand temperature.

(using oil) Apply a light coating of oil to grill surface. (Fry oil can be used) Whentoasting using oil, any high-quality cooking oil may be used with this toaster (do not use oils thatcontain dairy products suchas butter).TheTeflon sheetmaybeused, but it is not required.a. Turn Main Power Switch on. Set Temperature Control knob to desired temperature. Allow Pilot

Light to cycle at least two times (on/off). When the light is on, the grill is heating. Heat up time isabout 15-20minutes.

b. Turn onmotor switch.Conveyor should start to turn.c. Hold bunhalf in the palmof the hand, placebutter on cut side..d. Place bun halves on feeder cut side down (facing grill surface). Try several buns to determine

the correct pressure and time to achieve the desired browning and temperature of bun. Usingtoo little oil will cause the bun surface to be cool and uneven in color. It will also cause the bun tostick to the grill. Using too much oil will give the bun a yellow un-toasted look. Toast time isapproximately 210 sec. depending on bun height and diameter. Increase or decrease the

non-heated DO NOT USEANEXTENSION CORD.

1. Dryoperation.

2. Wet operation.

4

temperaturesetting to achievedesiredbrownnessand temperature.

Should the temperature setting be changed, allow several cycles for the grill plate to adjust.Once thedesired settinghasbeenachieved, note the temperatureand keep it set there.

Turn offmain power switch and conveyor switch.Disconnect the power supply cord from thewall outlet. Thetoasterwill be hotwhen turnedoff.Allow the toaster to cool for at least 15 � 30minutesbefore handling.

duringdisassemblyand cleaning.Remove theTopandBottomFrontPanels.

The Feeder, and Top and Bottom Front Panel can be placed in a dishwasher or sink and washed withdetergent andwarmwater.

Remove the conveyorassembly by gripping the two handles at the top and lifting forward until it clears the gears. Lift it up and outgently placing it in a sink with the drain stopped, or in a suitable container to soak over night. Conveyor canbe placed in the sink or container while warm. The soaksolution is a mix of 10 parts hot water (120ºF or more) to 1 part (minimum) �INSIDEOUT� brand 3-IN-1. Fillthe sink or suitable containerwith the solution, to completely cover the conveyor by approximately one inch.Allow the conveyor to soak in the solution over night. Remove the conveyor from the solution. Use a stiffnon-metal brush or plastic pad to remove residual bun oil. Insure the chains are clean and free from debris.Use a brush to remove any soil or debris remaining on the chain. Rinse conveyor with plain hot water andallow to drain. Lubricate both chains thoroughly with vegetable oil. Bun oil may be used if it contains noanimal fats, salts or dairy products.Gently replace conveyor into toaster.

Replace all removed toaster parts. Plug power supply cord intowall outlet. Turnmain power switch on. Turnconveyor switchon.

Severely baked on oils as shown in Figure 3 require the conveyor to be cleaned using the one-time boil outinstructionsbelow to clean.

NOTE:

WARNING: Make sure the toaster is in the off position and has been off at least 15 � 30minutes. Donot attempt this cleaningprocedure if the toaster components are toohot to touch.

Never spray water on the toaster or controls. Damage to the toaster as well as injury could occur.Severe injuryandburnsmayoccur if youdonot follow this instructionsheet.

DISASSEMBLY

USECAUTION

NOTE:Donotuseanychlorideor chlorine -basedproducts to cleanor rinse toasteror toasterparts.

DailyPartsCleaning:

DailyConveyorCleaning:Conveyor may be hot and is heavy, use caution when lifting and removing.

Use caution when handling a hot conveyor.

Note: Chain Lubrication is critical to chain life. Oil the chain daily.Discard used soak solution. Clean and sanitize sink or container

after overnightuse!

CLEANING

5

FIGURE 3

ONE-TIME BOIL OUT OF CONVEYOR

NOTE:This is for experiencedoperatorsonly, and in stores that approve thisoperation.

Gently

NOTE: Drain the solution prior to removing the Conveyor Assembly.

Note:ChainLubrication is critical to chain life.Oil chaindaily.

LAST IMPORTANT NOTE:

KEEPCONVEYORLOOKINGNEW.

1. Turn off power anddrain the oil fromoneof theFryers, andallow it to cool.2. TurnToastermain power switchoff. Removepower supply plug from thewall outlet.3. Some surfaces will remain hot after toaster is turned off. Allow time for toaster to cool. (15-30

minutes)Use cautionduringdisassemblyand cleaning.4. Remove theTopandBottomFrontPanels.5. When the fryer has cooledandhasdrained, close the drain valve.6. Remove the Conveyor assembly by grasping the two handles at the top, and lifting forward until

it clears the gears.7. place theConveyorAssembly into theFryer.8. Addwater to the cooled Fryer leaving enough room to add two (2) gallons of �INSIDEOUT� 3 IN

1HEAVYDUTYCLEANERand theConveyorAssembly.9. Addadditionalwater to theFryer, if necessary, to completely cover theConveyorAssembly.10. Set the temperature of the Fryer to 200ºF, and allow the conveyor to soak in the solution for 60

minutes.11. Shut off theFryer andallow the conveyor to cool.12. After the conveyor

has cooled, remove the conveyor from the Fryer. If there are areas with bun oil, use a stiff non-metal brush or plastic pad to remove. Insure the chains are clean and free from impediment.Useabrush to removeany soil or impediment remainingon the chain.

13. Rinse conveyor with hot water and allow to drain. Lubricate both chains thoroughly withvegetable oil. Bunoilmaybeused if it contains noanimal fats,salts or dairy products.

14. Before assembly of the conveyor check the Following: ConveyorAssembly hardware to insurefasteners are tight and there are no signs of wear, Gears are tight on theConveyor shaft and theMotor Shaft and the Hanger Bracket screws are tight and the brackets have not shifted duringuse.

15. Gently replace conveyor into toaster. Replace all removed parts. Plug power supply cord intowall. Turnmain power switchon.Turn conveyor switchon.

Daily-cleaning instructions of conveyor should be followed after this boil out.The conveyormust stay clean to optimize speedandbuntemperature.

DailyGriddleCleaning:

Dry Operation:

WetOperation:

Toolsneeded for cleaning:

Alsoneeded:

Wipe off the Teflon sheet with a damp cloth to remove any debris or particles that havecollectedon the sheet. If the sheet isworn, replace it with a newsheet.

It is not necessary to completely remove residue, as long as the grill surface is smooth andfreeof burnedonbread thatmay causebuns to stick.

Scotch-BriteTMQuickCleanSmallApplianceCleanerNo. 702orEquivalent�Scotch-BriteTMMulti-PurposePadHolderNo. 405orEquivalent�Scotch-BriteTMSqueegeeNo. 410orEquivalent�Scotch-BriteTMGriddlePolishingPadNo. 46orScotch-Brite�GeneralPurposeScrubbingPadNo. 9650orEquivalent

�(Wet) terry towel �Catchpan for food soil �Commonkitchenscraper

6

FIGURE 4 FIGURE 5 FIGURE 6

FIGURE 7 FIGURE 8

Scour usingScotch-Brite Multi-PurposePadHolderNo. 405or equivalent, andScotch-BriteGriddlePolishingPadNo. 46 (or 9650). (SeeFigure4)

After scouring,Squeegee the surface cleanwith theScotch-Brite SqueegeeNo. 410 (SeeFigure5)

Turn off Bun Grill Toaster and wipe surface with clean wet towel. If the surface is still hot, use the Scotch-

Brite Multi PurposePadHolder tomove the towel over the surface. (SeeFigure6)

Dry the grill thoroughly. Coat the grill platewith a light filmof cookingoil. SeeFigure7)

Rinseall cleaning toolswith hotwater. (SeeFigure8)

Wipedownall external stainless steel surfaceswith a dampcloth.

Before assembling the conveyor check the following: Fasteners on the Conveyor Assembly hardwareshould be tight with no signs of wear. Conveyor Shaft Gear andMotor Shaft Gear are tight. Hanger BracketScrewsare tight and thebrackets havenot shifted duringuse.

TM TM

TM

TM

RE-ASSEMBLY

.

7

If Teflon sheet is installed remove it when Bun Grill Toaster is cool. Set the toaster temperature to 350°F.Scrape loose foodparticleswith scraper into a panunder grill plate.

Squeeze 1 to 2 ounces of Scotch-BriteTMQuick Clean SmallApplianceCleaner No. 702 or equivalent intomeasuring reservoir of bottle. Pour cleaner onto pad.Donot pour directly onto grill surface.

TROUBLESHOOTING GUIDE

Alwaysask and check the following:Is the unit connected to a live power sourceof the proper voltage?Check the circuit breaker.Is power switch �ON� andpilot light glowing?Check the rating label. Is the unit connected to the correct power source?

If the above checks out, and you still have problems, call anAPWWyott authorized service agent.

1.2.3.4.

APWSERVICEHOTLINE1-800-733-2203

Buns wont toast Wrong temperature setting

Excessive cupping of bunsurface

Increase temperature settingand allow two cycles to warmup.

Buns are stale, use fresherbuns

Buns toast unevenly Excessive cupping of bunsurfaceConveyor pressure too light

Buns may be stale. Try fresherbunsAdjust conveyor tension

Buns stick to grill Teflon sheet worn.

Doughy buns or excessivesugar and moisture, plus grilltemperature too high.

Build up on Grill Surface

Replace Teflon sheet

Reduce grill temperatureAllow buns to age.

Clean Grill per instructions

No power No power at the wallreceptaclePower cord disconnectedMain switch

Check circuit breaker or fuse

Check plug at receptacleCheck that switch is ON andoperative

Conveyor will not turn (Motorturns)

Drive gears not engaged

Gear set screws not tight

Check gear alignment andengagementCheck screws and tighten ifrequired

PROBLEM CAUSE SOLUTIONPROBLEM CAUSE SOLUTION

8

SPECIFICATIONS

9

23.498

17.44717.44717.447

23.498

21.888

APPROX.

00

APPROX.

21

.

840

19.340

20.590

21.88821.888

19.340

20.59021.840

16.272

15.002

9.500

10.750

12.000

4.000

15.00215.002

16.27216.272

9.500

10.750

12.000

PARTS LIST w/EXPLODED VIEW

EXPLODED VIEW

35

36

32

54

67

68

11

25

20

19

58

64

55

46

3

17

6

4

5

18

2

13

56

9

15

12

8

63

66

14

1

7

24

26

47

62

34

27

61

39

59

50

57

22

43

37

52

69

21

48

42

60

41

53

23

45

44

33

31

16

10

65

29

30

28

39

40

38

51

49

70 71

37

43

4845

44

5

9 12

23 13

21

68

54 24

27

6

70

4662

71

414 17

1547

35

36

1864

282930

50

39

67

34

5620

11

7

16 63

1021

4931 32

33

52

61

22

59

8

51 40

69

26

19 25

65

5753 55

66

38 341

42

60

5839

PARTS LISTITEM PART NUMBER DESCRIPTION QUANTITY

11

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071

8626086219P86204

70202012862108620786261

7020200986233

942000958373386235

83065 SON8625986234

702000528620686211850338504389057889848914386265845598912087074

942000897020005194000172

894086301289491

709000093423634237890038907388889391008907189061889938916489163862023909989059889018894889054890298911160113856478649188961852848892389063887058628486253852858918286256

704390986914789042

7020201670202015

PANEL, TOP FRONTELEMENT, GRILL 208/240VPLATE, MOTOR MOUNTINGPANEL, CONTROL M-2000 JIBPANEL, LEFT SIDE OUTERPANEL, BACKPANEL, BOTTOM FRONTLABEL, M2K JIB CONTROLANGLE, GRILL PLATEKIT, POWER SUPPLY, 5V/24V OUTPUTROD, FRONT AND TOPW/ASS'Y, LEFT SIDE PANELW/A Hanger Arm LHSHIELD, FRONT GRILLW/ASS'Y, RIGHT SIDE PANELCHAIN/WEIGHT CONV.ASS'Y (COMP) M-95-2PANEL, BOTTOMPANEL, RIGHT SIDE OUTERGEAR, 13 TOOTH 3/8 BOREGEAR, 19 TOOTHWASHER, LOCK #6 INTERNALSCREW 6-32 X 3/8 PAN HDPLUG, HYCO # DP-187W/ASS'Y, SUPER FEEDERPLUG, HOLE HEYCO #DP687CLIP, JIFFYPIN, HANGERMERKLE-KORFF MOTORSPEED CONTROL BRACKET10K OHM POTENTIOMETERSWITCH, LIGHTED ROCKERS/A, PILOT LIGHTSWITCH,ROCK,DPST,20A 250VAC,BLK (TEXT)LEG, 4" METAL ADJ. LEGTERMINAL BLOCK END MTGTERMINAL BLOCK .250 MALEBOLT,1/4-20 X 1/2" SS HEXSCREW, #8 X 1/2 HEX TAPIT SHT MTL TYPE ABSCREW #8 X 1/2 AB SMS PHL TRUSS LGM NI PLTPROBE, THERMOSTATWASHER, #10 FLATNUT, HEX 10-24SCREW 10-32X3/8 TRS HD PHILLIPS NYLK MSSCREW, 1/4-20 X 5/8 HEX SL NCK PLNUT, JAM HEX 1/4-20 N.P. SSCOVER, INSULATIONT'STAT, FASTRON G6WASHER #10 EXTERNAL LOCKSCREW 6/32 X 1/4 PAN HD M/S BLKZCSCREW 6-32 X 3/4 PAN HDNUT, KEPS 6-32SCREW, 10-24 X 3/8 PH PAN SSBUSHING, STRAIN RELIEF SR-7W-2INSULATION, 21X19X1CORDSET, 14/3 600V .440 HSJO 620PW/A Hanger Arm RHNUT, HEX 10-24, GREENFAN, COOLING 4.5" 105CFM 208/230VSCREW, 8-32x1-3/4 SLT PAN MS SSNUT, HEX 8-32KNOB 039-266 8A BLACKSCREW, 8-32x1/4 PHIL PAN TYPE 23 ZINKRACK, BOTTOM WIREASSY, FAN CORD(FAN CORD 85283)BUSHING, .5 HEYCO 2058BRACKET, CAPILARYRELAY,SLD ST 50A 280V OUT,90-280VAC INPAD, THERMAL FOR SSR 69146 (TEXT)SCREW 8-32 X 1/2 PH SL SSLABEL, CROWNLABEL, HEEL

111111112111111111114431122111111415107271971322111222411111114418111111211

WIRING DIAGRAM

L1 BROWN

L2 BLUE

CORDSET 85640

RELAY 70439098

LIGHTED ROCKER SWITCH 89406

PILOT LIGHT 63012

THERMOSTAT 39099

RTD PROBE 39100

LIGHTED ROCKER SWITCH 89408

11

L1

L2

L2

L1

RTD PROBE 39100

1

2

10

12

13

7

9

14

WIRE HARNESS 94200093MOTOR 94200089

GRILL PLATEN 86219-P

M2K TERMINAL BLOCK ASSY

34236 (1) 34237 (5)

POWER SUPPLY 94100140

3 PIN HARNESS 94100061

6 PIN HARNESS 94100134

SPEED POT. 94000172

FAN 85284

FAN CORD 85283

GRND

REDBLACK

BLUE

BLUE

WHITE

RED

BLACK

RED

RED

RED RED

BLACK

WHITEWHITE

WIRE NUT

89149

ORANGE

GREEN

ORANGE

GREEN

BLACK

WIRES NOT IN WIRE SET

RED

BLACK

RED

BLACK

1

2

3

4

4

3

56

6

5

788

99

7

10 10

10

11

11

1111

12

1313

14

14

14

5

6

L2 L2

L2 L2

L1 L1

L1 L1

IN LINE RESISTOR

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. ForWarrantyServiceand/orParts, this information is required.

ModelNumber SerialNumber DatePurchased

Notes:

13

Notes:

14

15

APWWYOTT EQUIPMENT LIMITEDWARRANTY

APWWyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to thefollowing conditions:

This warranty applies to the original owner only and is not assignable.

Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option ofAPW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only beresponsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW WyottAuthorized ServiceAgencies will void this warranty andAPWWyott will not be responsible for such work or any charges associatedwith same. The closestAPWWyottAuthorized ServiceAgent must be used.

This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas ofAlaska and Canada. Therewill be no labor coverage for equipment located on any island not connected by roadway to themainland.

One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agencymay, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of theoriginal product warranty only.

Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on allcomponent parts, except switches and thermostats. (2 additional years on parts only.No labor on second or third year.)

In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.

Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipmentweighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject tothe following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day ofconnection, or use, atAPWWyott's option or itsAuthorized ServiceAgency, it will be serviced on site or replaced.

From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW WyottAuthorized ServiceAgency for in-warranty repairs. Nomileage or travel charges are allowed on portable units after the first day of use.If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)countertop warmers and cookers, which are covered under the EnhancedWarranty Program, and (2) toasters or rollergrills which havein store service.

The following conditions are not covered bywarranty:*Equipment failure relating to improper installation, improper utility connection or supply and problems due toventilation.*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaningandwater damage to controls.*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.*Equipment that has themodel number or serial number removed or altered.

If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after thewarranty period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from theuse of the equipment thereafter.

This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times whichnormally involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and suchpremium rates.APWWyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.

In all cases, the use of other thanAPWWyottAuthorized OEMReplacement Parts will void this warranty.

This equipment is intended for commercial use only.Warranty is void if equipment is installed in other than commercial application.

Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened beforebeing used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.

9/05

Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canadamay vary. Contact the internationalAPWWyott distributor, dealer, or service agency for details.

Models FD, FDL, FDD, FDDL. Two (2)YearWarranty on element only. No labor second year.

TimePeriod

Exceptions*Gas/Electric Cookline:

*GlassWindows, Doors, Seals, Rubber Seals, Light Bulbs:

Portable Carry InProducts

Exclusions

WaterQuality Requirements

Note: Product failure caused by liming or sediment buildup is not covered under warranty.

�THE FOREGOINGWARRANTY IS IN LIEU OFANYANDALLOTHER WARRANTIES EXPRESSED OR IMPLIEDINCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSESAND CONSTITUTES THE ENTIRE LIABILITY OFAPWWYOTT. IN NO EVENT DOES THE LIMITEDWARRANTYEXTENDBEYONDTHETERMS STATEDHEREIN.�

*BroilerBriquettes,*Heat Strips:

RockGrates,CookingGrates, BurnerShields, Fireboxes: 90DayMaterialOnly.NoLabor.

90DayMaterial Only. NoLabor.

Phone: +1Fax: +1 (214) 565-0976Toll Free: +1 (800) 527-2100Website: www.apwwyott.comE-mail: info@apwwyott.com

(214) 421-7366

APW WYOTT729 Third AvenueDallas, TX 75226

(800) 733-220324 Hour Service Hotline

R

16