internet of things _ open source home automation project using arduino uno + ethernet shield
DESCRIPTION
aTRANSCRIPT
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 1/21
IoT Pune Community Blog.
Internet of Things
S a t u r d a y , J u l y 1 3 , 2 0 1 3
Open Source Home Automation Project using ArduinoUNO + Ethernet Shield
The main brain for this project is Arduino UNO Board along with Arduino Ethernet Shield togive it a wireless connectivity.Arduino runs a code to control a Relay board according to theinput and also serves a web page through which respective output to the relay board can becontrolled.Through relay controller board we can control lamps, tubes or any AC powersockets.You will be able to control all of your AC Appliances wirelessly with the help of any WIFIEnabled device.
Quantity of the components depends upon how many channels you want e.g. if you want tocontrol more than one light then you will have to add that much number of relays on yourcontroller board.Here is the material list which will be needed to build the board: (Quantity of the componentsgiven for making 1 channel relay controller)
Sr.No Component Names Quantity
1 Relay (I have used GOODSKY RWHSH105D Relay) 1
2 Transistor 2N3904 1
3 1K Resistor 2
4 10K Resistor 1
5 1N4148 Diode 1
6 Red Led 3mm 1
7 3 Pin PCB Mount Connector 1
8 1 Pin PCB Mount Connector 1
Above components are for making of single controller board you can multiply number of thecomponents depending on how many relay controller you want.
This is Open Source Home Automation Project based on Arduino Uno and ArduinoWiznet based Ethernet shield.
How Does it Work
STEP 1:
Relay Controller Board Build Tutorial:
Follow by Email
Email address... Submit
Internet of Things groups is a local group atPune, India.
It was started by folks who also now run Doo a Maker Space.
1. To foster a DIY culture for electronics andhacking with sensors for fun and knowledge.2. Engage with educational institutes tointroduce arduino kits for fun and learning.
About IOT Group
14
Open Source HomeAutomation Project usingArduino UNO + EthernetShieldThis is Open Source HomeAutomation Project based
on Arduino Uno and Arduino Wiznet basedEthernet shield . How Does it Work T...
Home Automation withRaspberryPi Python DjangoHome Automation withRaspberryPi Python Django So after attending
the 2 meetups for IOTPune. I got aRaspberry Pi and decided ...
Using Raspberry Pi as a torrent client.Using Raspberry Pi as a torrent clientAdvantage of using raspberry pi as a torrentclient is that it uses very less power. For acom...
Arduino with real time webapplication using websocketsPurpose of this experimentis to demonstrate real timeaspect of the web to pull
data from an Arduino . Arduino can beclubbed toget...
Using Raspberry Pi as IRC ClientI wanted to be continually logged into IRCand also use it as a logging client formessage on the #doothings IRC channel.What better ...
Getting started with the BeagleBone BlackArduino is the most ubiquitous developmentplatform, period. Anyone who has enteredthe world of DIY electronics most probablystarted off ...
Twitter Sentimental Bulbs + Ruby!I presented at the RubyConfIndia 2013 onthe topic of Arduino + Ruby and hadplanned to show 2 Demo's to the attendees.A bubbli...
Connect BeagleBone Black to Android(xpost)19th January '14 Some of the methods thatI think can be used to setup duplexcommunication between an Androidapplication and a Beagl...
Raspberry Pi ScoreboardThis is a simple project that tries to use theRaspberry Pi as a Scoreboard.. on acharacter LCD What we will do in thisproject is write...
Popular Posts
2 More Next Blog» Create Blog Sign In
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 2/21
Here in the circuit diagram Pin no.2 will be connected to the arduino control output pin andother two will be connected to +5V and Gnd accordingly.After soldering all of your components according to the above circuit diagram the boardshould look like this.
Front View
Rear View
This is single relay controller board. You can extend this to as many as you want. I havemade 5 channel relay controller board as below.
Arduino based Tic Tac Toewith TV RemoteThis was my first timeattending the Internet ofThings Pune Group . It wassuch a fun learning
experience! At today's meetup, Dhira...
2014 (12)
2013 (9)
October (3)
August (1)
July (3)
Getting started with the BeagleBoneBlack
Open Source Home Automation Projectusing Arduino ...
Twitter Sentimental Bulbs + Ruby!
June (1)
May (1)
Blog Archive
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 3/21
All the usual warnings apply: Mains voltage (120VAC or 220VAC) can kill you. Thisproject, if done incorrectly, could certainly burn down your house. Do not work on orsolder to any part of a project while it is plugged into the wall socket just unplug itbefore modifying anything!
Mount your Arduino Ethernet shield on Arduino Uno as shown:
Note:
STEP 2:Getting IP Address Of Arduino Ethernet Shield:
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 4/21
Now connect your Uno Board to PC with USB cable and open Arduino IDE. After Opening upyou will find blank Arduino window. Now go to File> Example > Ethernet > dhcp addressprinter sketch. Your Ethernet shields MAC address is printed on back of it as follow you willneed this in DHCP ADDRESS PRINTER code to get the IP address of your Ethernet shield.
In DHCP address printer sketch put your MAC address as given on back of the Ethernet shieldand upload it to the Arduino board.
After finished uploading connect Arduino Ethernet shield to internet with Ethernet cable once
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 5/21
connected then open up you serial monitor of Arduino IDE the IP address allotted to yourEthernet shield will be displayed e.g. (xxx.xxx.x.xxx) note it down somewhere because you aregoing to need this in further codes.
BuildingMainCircuitConnection :
Now we are ready with our Relay controller board. So, it’s time to move on to the Main CircuitConnections. Here I have given the pin configuration for the whole Autohome Project.
Arduino Digital Pin No. Pin Usage
4 will be used for Infrared Receiver
5 used as Output Pins to control Relays
6 used as Output Pins to control Relays
7 used as Output Pins to control Relays
8 used as Output Pins to control Relays
9 used as Output Pins to control Relays
10 will be used by Arduino Ethernet Shield
11 will be used by Arduino Ethernet Shield
12 will be used by Arduino Ethernet Shield
13 will be used by Arduino Ethernet Shield
Note: For relays it is recommended to power it from separate source not from Arduino (I havepowered it from Arduino only but since here we are working with single board. As boardnumber increases Arduino won’t be able to supply sufficient power to the boards.)Here is the connection diagram:
In this way you can do necessary soldering work to make following connection.You can also make your own protoshield which can easily fit on top Arduino like this:
STEP 3:
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 6/21
Once you finish soldering stuff, now you are ready for your main code upload.
STEP 4:
Uploading Arduino AutoHome code to the Board:
Here is the Arduino AutoHome code just copy and paste it into your Arduino IDE sketch.
12345678910111213141516171819
//for use with IDE 1.0
//open serial monitor to see what the arduino receives
//use the \ slash to escape the " in the html
//for use with W5100 based ethernet shields
// this project is hosted at
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 7/21
2021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106
// http://code.google.com/p/arduinoautohome/
#include <SPI.h>
#include <Ethernet.h>
byte mac[] = 0x90, 0xA2, 0xDA, 0x0D, 0x78, 0xE0 ; // < PUT YOUR MAC Address Here
byte ip[] = 192, 168, 1, 102 ; // < PUT YOUR IP Address Here
byte gateway[] = 192, 168, 1, 254 ; // < PUT YOUR ROUTERS IP Address to which your shield is connected Here
byte subnet[] = 255, 255, 255, 0 ; // < It will be as it is in most of the cases
EthernetServer server(80); // < It's Defaulf Server Port for Ethernet Shield
String readString;
//////////////////////
void setup()
pinMode(6, OUTPUT); // Pin Assignment through which relay will be controlled
pinMode(7, OUTPUT);
pinMode(8, OUTPUT);
pinMode(9, OUTPUT);
//start Ethernet
Ethernet.begin(mac, ip, gateway, subnet);
server.begin();
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 8/21
107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193
//enable serial data print
Serial.begin(9600);
Serial.println("server LED test 1.0"); // so that we can know what is getting loaded
void loop()
// Create a client connection
EthernetClient client = server.available();
if (client)
while (client.connected())
if (client.available())
char c = client.read();
//read char by char HTTP request
if (readString.length() < 100)
//store characters to string
readString += c;
//Serial.print(c);
//if HTTP request has ended
if (c == '\n')
///////////////
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 9/21
194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280
Serial.println(readString); //print to serial monitor for debuging
/* Start OF HTML Section. Here Keep everything as it is unless you understands its working */
client.println("HTTP/1.1 200 OK"); //send new page
client.println("ContentType: text/html");
client.println();
//client.println("<meta httpequiv=\"refresh\" content=\"5\">");
client.println("<HTML>");
client.println("<HEAD>");
client.println("<meta name='applemobilewebappcapable' content='yes' />");
client.println("<meta name='applemobilewebappstatusbarstyle' content='blacktranslucent' />");
client.println("<link rel=\"stylesheet\" type=\"text/css\" href=\"http://arduinoautohome.googlecode.com/svn/trunk/autohome.css\" />");
client.println("</HEAD>");
client.println("<body bgcolor=\"#D0D0D0\">");
client.println("<hr/>");
client.println("<hr/>");
client.println("<h4><center><img border=\"2\" src=\"https://lh3.googleusercontent.com/C6BoJrRUFko/UEUFeCwkvdI/AAAAAAAAAOc/E7gcYvPV6r4/s960/Logo.jpg\" /></center></h4>");
client.println("<hr/>");
client.println("<hr/>");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 10/21
281282283284285286287288289290291292293294295296297298299
// Relay Control Code
client.println("<a href=\"/?relay1on\"\">Turn On Light 1</a>");
client.println("<a href=\"/?relay1off\"\">Turn Off Light 1</a><br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<a href=\"/?relay2on\"\">Turn On Light 2</a>");
client.println("<a href=\"/?relay2off\"\">Turn Off Light 2</a><br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<a href=\"/?relay3on\"\">Turn On Light 3</a>");
client.println("<a href=\"/?relay3off\"\">Turn Off Light 3</a><br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<br />");
client.println("<a href=\"/?relay4on\"\">Turn On Light 4</a>");
client.println("<a href=\"/?relay4off\"\">Turn Off Light 4</a><br />");
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 11/21
client.println("<br />");
client.println("<br />");
// control arduino pin via ethernet Start //
if(readString.indexOf("?relay1on") >0)//checks for on
digitalWrite(6, HIGH); // set pin 4 high
Serial.println("Led On");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/on.png' />");
//client.println("Light 1 Is On");
client.println("<br />");
else
if(readString.indexOf("?relay1off") >0)//checks for off
digitalWrite(6, LOW); // set pin 4 low
Serial.println("Led Off");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/off.png' />");
//client.println("Light 1 Is Off");
client.println("<br />");
if(readString.indexOf("?relay2on") >0)//checks for on
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 12/21
digitalWrite(7, HIGH); // set pin 4 high
Serial.println("Led On");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/on.png' />");
//client.println("Light 2 Is On");
client.println("<br />");
else
if(readString.indexOf("?relay2off") >0)//checks for off
digitalWrite(7, LOW); // set pin 4 low
Serial.println("Led Off");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/off.png' />");
//client.println("Light 2 Is Off");
client.println("<br />");
if(readString.indexOf("?relay3on") >0)//checks for on
digitalWrite(8, HIGH); // set pin 4 high
Serial.println("Led On");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/on.png' />");
// client.println("Light 3 Is On");
client.println("<br />");
else
if(readString.indexOf("?relay3off") >0)//checks for off
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 13/21
digitalWrite(8, LOW); // set pin 4 low
Serial.println("Led Off");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/off.png' />");
//client.println("Light 3 Is Off");
client.println("<br />");
if(readString.indexOf("?relay4on") >0)//checks for on
digitalWrite(9, HIGH); // set pin 4 high
Serial.println("Led On");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/on.png' />");
//client.println("Light 4 Is On");
client.println("<br />");
else
if(readString.indexOf("?relay4off") >0)//checks for off
digitalWrite(9, LOW); // set pin 4 low
Serial.println("Led Off");
client.println("<link rel='appletouchicon' href='http://chriscosma.co.cc/off.png' />");
//client.println("Light 4 Is Off");
client.println("<br />");
// control arduino pin via ethernet End //
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 14/21
// Relay Status Display
client.println("<center>");
client.println("<table border=\"5\">");
client.println("<tr>");
if (digitalRead(6))
client.print("<td>Light 1 is ON</td>");
else
client.print("<td>Light 1 is OFF</td>");
client.println("<br />");
if (digitalRead(7))
client.print("<td>Light 2 is ON</td>");
else
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 15/21
client.print("<td>Light 2 is OFF</td>");
client.println("</tr>");
client.println("<tr>");
if (digitalRead(8))
client.print("<td>Light 3 is ON</td>");
else
client.print("<td>Light 3 is OFF</td>");
if (digitalRead(9))
client.print("<td>Light 4 is ON</td>");
else
client.print("<td>Light 4 is OFF</td>");
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 16/21
client.println("</tr>");
client.println("</table>");
client.println("</center>");
//clearing string for next read
readString="";
client.println("</body>");
client.println("</HTML>");
delay(1);
//stopping client
client.stop();
Upload this code to your UNO board. Now you are ready to your your Automation Project,just plug your Ethernet shield to router and and you will be able to find the control page onthe IP Address specified by in in the Arduino Code. So directly enter the IP address in theweb browser of the the device which is on the same network as that of your Arduino.
So you will have the control page as shown below:
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 17/21
Posted by dhiraj at 9:44 PM
Labels: Arduino, DIY, ethernet shield, home automation
As you understand the code you can modify to your need.So enjoy controlling things wirelessly..
+2 Recommend this on Google
Replies
Reply
37 comments:
Clint VanRoekel November 14, 2013 at 9:11 PM
GREAT PROJECT ! ! ! ! ! ! !
Is there an easy way to password protect the web server?
Reply
Rituparna Matkar November 24, 2013 at 2:45 PM
Hi Dhiaraj
I wanted to know what is the best way to know if current is passing through a switch. So letme explain better. If these two switched are in parallel there is a feedback on the state of theswitch if we turn it of from the aurduno but what can be done to get a feed back if the switchon the wall is turned on . Is there a mechanism that can send a signal aying what is the stateof the switch
Reply
mai punye blog December 6, 2013 at 1:08 AM
hey. i am very interested with your project and i am thinking of making this project as my finalyear project. may i get the full report of the project? please contact me at my email,[email protected]. thank you. have a nice day.
Reply
rahubawan bawan December 14, 2014 at 1:21 PM
did u do it
jalal December 19, 2013 at 7:00 PM
hi,, dhiaraji'm thinking about your project to make it self .can you email me the project [email protected]
Reply
Nishant Modak December 19, 2013 at 7:11 PM
Everything about the project that you would need to do it yourself is mentioned in theblogpost. What else do you want?
Reply
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 18/21
Replies
Reply
Replies
Reply
Replies
Reply
jalal December 19, 2013 at 8:39 PM
i'm worry about enternet shield,,thanks
nicholas cobb January 4, 2014 at 6:23 AM
how do you get the ethernet shield to work with the arduino mega? please help me
Reply
Owais Malik January 24, 2014 at 10:47 PM
Reply
This comment has been removed by the author.
Apcc DIY February 13, 2014 at 3:45 PM
nice work! I want to make something similar, but adding some pir sensors for home alarm system. I already ordered an arduino Leonardo and arduino Ethernet shield.Lucky for me, I hade from an old project an TC35 gsm module, and I want to use it for smsremote.
Reply
kasi March 4, 2014 at 8:51 AM
Can u help me with the using the gsm sheild for home automation
Aravind Kv March 1, 2014 at 8:16 PM
Very helpful..thank you so much..i am doing a similar project for my final year engineeringcourse and i would like to clarify a few things..please contact me [email protected] again
Reply
ben stiffler March 2, 2014 at 9:57 PM
Hello,let's say i'm running the web control for switches at home, and there is someone at home whowants to switch manually at the same time while the web control is running.So do you have a solution for that ? Thank you
Reply
nuke rox May 2, 2014 at 3:08 PM
the solution is simple. just use a two way switch as the manual control switch
BazOOka April 15, 2014 at 1:27 AM
helloo can u please help me i have an wifi shield and i can not access the page that appearsin the serial monitor can u do an sketch for the wifi shield
Reply
Henrik April 24, 2014 at 12:40 AM
Hi, You should probably check out the MySenors project to make your sensor wireless using thenRF24L0 radio.
Website:http://mysensors.org/
Github:https://github.com/mysensors/
CheersHenrik
Reply
Aditya Jain May 18, 2014 at 2:36 PM
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 19/21
Replies
Reply
is ethernet shield cable rj45 is connected to laptop or some other place??
Reply
Calin Dragos May 20, 2014 at 1:25 PM
You have here one of the best Arduino Uno projects for both beginners and advanced users. Iwrite an article especially for beginner users to help them starting building electronic projectsusing the Arduino Uno board. Here is the link to the article
http://www.intorobotics.com/arduinounosetupandprogrammingtutorials/
Reply
Thisara Pathirana June 14, 2014 at 7:30 PM
How can I get IP address for me.
Reply
T's June 17, 2014 at 10:39 PM
Reply
This comment has been removed by the author.
T's June 17, 2014 at 10:42 PM
Hello, can anyone help me? i want to build bell door wireless for deaf people using two ethernet shield. The idea is, ifsomeone press the bell on the door, it will transmit the output to arduino 1 that connect toethernet shield 1 and display it with LED and also transmit the output using wireless router toarduino 2 mounted with ethernet shield 2 and display it with LED on the other room. I don'tplan using web server based. And all the example from the web is using internet connectionand accessing/controlling via web, so i'm troubled over here. Help me please, i reallyappreciate it! [email protected]
Reply
HVJ July 12, 2014 at 3:24 AM
Hello TNice I am really interested in your project for elderly if you have completed canyou please share Thanks
rahubawan bawan November 25, 2014 at 2:12 PM
hi,, dhiaraji'm thinking about your project to make it self .can you email me the project [email protected]
Reply
Abhijeet Ramgir December 12, 2014 at 2:37 AM
does this work with the latest ide?
Reply
Eric Brouwer February 22, 2015 at 10:34 PM
Thanks for sharing. I like the graphics displayed on the page.
Reply
Eric Brouwer February 22, 2015 at 10:34 PM
Thanks for sharing. I like the graphics displayed on the page.
Reply
BMasterBM1 March 2, 2015 at 3:29 AM
Great work, but I have a problem. I connected everything ( I bought relay module on ebay),but it wont work. When I click "turn light on" nothing changes. Serial monitor gives "GET", buteven in the table at the bottom of the page nothing changes. Any ideas?
Reply
DEEKSHA May 9, 2015 at 3:48 AM
Reply
This comment has been removed by the author.
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 20/21
DEEKSHA May 9, 2015 at 3:50 AM
Hey Dhiaraj,
I really like your project!! I would like to know if I can connect all the components on abreadboard instead???And would like to know more details about your project as I would like to make it a part of mycourse work. Kindly mail me the report of you project. [email protected]
Thank you
Reply
Samiksha Lokhande May 20, 2015 at 4:46 PM
Wow diraj, what a talent, I am speechless. You have done such a amazing work about homeautomation products that I cant even thing about that, thanks for sharing.
Reply
Punith B May 23, 2015 at 1:33 PM
Hi.. Great work! It worked for me. I would like to know how to control the devices using otherrouters/ gateway. For example I would like to control from my office..Please help me out with this..
Reply
John Diesel July 24, 2015 at 11:07 AM
Your description is really very nice and interesting in which there is the discussion aboutInternet things. Thanks for sharing this info and please keep sharing.
Security service in vancouver | Security Service in Vancouver
Reply
Sanket Dongre August 7, 2015 at 5:36 PM
Hello guys, I am Sanket Dongre. I am the founder of creatiwit.com, an educational startupwith a mission to help people learn real world skills interactively.As you all know IOT is the next big thing, I was planning to create a course on IOT forbeginners, also basics in Arduino, Raspberry Pi and other stuff which set the foundation forpursuing IOT. For this, I am loooking for Instructors who are experts/hobbyists and who are willing to sharetheir knowledge. Course can be selfpaced/live. If anyone interested, kindly call me at:7709197929 or email at: [email protected]: 85% commission per sale of course will be paid to the instructor.
Reply
Sanket Dongre August 7, 2015 at 5:38 PM
Also if anyone intersted in conducting workshops in colleges/companies can also register onour platform or contact me.Awaiting your response.
Reply
Delight Display August 11, 2015 at 4:55 PM
Thanks for making the effort to describe the terminlogy to the beginners!
electronic display boards india
Reply
pranao ramteke August 20, 2015 at 11:39 AM
hi pls forward me the complete project report on [email protected] let me tell u this that u made an awesome circuit i wana know more abt this pls forwardme as soon as possible
Reply
pranao ramteke August 20, 2015 at 11:40 AM
hi pls forward me the complete project report on [email protected] let me tell u this that u made an awesome circuit i wana know more abt this pls forwardme as soon as possible
Reply
9/4/2015 Internet of Things : Open Source Home Automation Project using Arduino UNO + Ethernet Shield
http://internetofthings-pune.blogspot.in/2013/07/this-is-open-source-home-automation.html 21/21
Newer Post Older PostHome
Subscribe to: Post Comments (Atom)
Sign out
Notify me
Enter your comment...
Comment as: MAHAMMAD SUHAIL (Google)
Publish Preview
Create a Link
Links to this post
Simple template. Powered by Blogger.