introduction to materials science, chapter 19, electrical properties university of virginia, dept....

24
Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation of conductivity (I) = n|e| e + p|e| h Strong exponential dependence of carrier concentration in intrinsic semiconductors Temperature dependence of mobilities is weaker. n = p A exp (- E g /2 kT) C exp (- E g /2 kT)

Upload: marian-nicholson

Post on 26-Dec-2015

227 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 1

Temperature variation of conductivity (I)

= n|e|e + p|e|h

Strong exponential dependence of carrier concentration in intrinsic semiconductors

Temperature dependence of mobilities is weaker.

n = p A exp (- Eg /2 kT) C exp (- Eg /2 kT)

Page 2: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 2

Temperature variation of conductivity (II)

n = p A exp (- Eg /2 kT) C exp (- Eg /2 kT)

Plotting log of , p, or n vs. 1/T produces a

straight line. Slope is Eg/2k; gives band gap energy.

k2

E

T1

pln g

ln(n) = ln(p) ln(A) - Eg /2 kT

Page 3: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 3

Temperature variation of conductivity (III)

Extrinsic semiconductors

• low T: all carriers due to extrinsic excitations

• mid T: most dopants ionized (saturation region)

• high T: intrinsic generation of carriers dominates

Page 4: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 4

Semiconductor Devices. Diode (I)

Diode allows current flow in one direction only

p-n junction diode: adjacent p- and n-doped semiconductor regions

Positive side of a battery is connected to p-side (forward bias): large amount of current flows. Holes and electrons pushed into junction region, where they recombine (annihilate).

Page 5: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 5

Semiconductor Devices. Diode (II)

If the polarity of the voltage is flipped, the diode operates under reverse bias. Holes and electrons are removed from the region of the junction, which therefore becomes depleted of carriers and behaves like an insulator.

Page 6: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 6

Semiconductor Devices. Diode (III)

Reverse bias: holes and electrons are drawn away from junction.

Junction region depleted of free carriers current is small.

Page 7: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 7

Semiconductor Devices. Diode (IV)

Asymmetric current-voltage characteristics of diode converts alternating current to direct current (rectification).

Page 8: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 8

Transistors.

Used to amplify electric signal and

Switching devices in computers.

Two major types

Junction (or bimodal) transistor

MOSFET transistor.

p-n-p (or n-p-n) junction transistor contains two diodes back-to-back. The

Central region (base) is thin (~ 1 micron or less) and is sandwiched in between emitter and collector

Page 9: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 9

Junction transistor

Emitter-base junction is forward biased: holes are pushed across junction. Some recombine with electrons in the base, but most cross the base as it is thin. They are then swept into the collector.

A small change in base-emitter voltage causes a relatively large change in emitter-base-collector current. Hence a large voltage change across output (“load”) resistor - voltage amplification

Page 10: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 10

Junction transistor

Emitter-base junction is forward biased, base-collector junction is reverse biased.

Thus, the base of the PNP transistor must be negative with respect to the emitter, and the collector must be more negative than the base.

Page 11: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 11

PNP Forward-biased junction

Forward biased emitter-base junction, positive terminal of battery repels emitter holes toward base, while negative terminal drives base electrons toward emitter

Page 12: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 12

PNP junction interaction

In reverse-biased junction: negative voltage on collector and positive voltage on base blocks majority current carriers from crossing junction.

Increasing forward-bias voltage of transistor reduces emitter-base junction barrier. This allows more carriers to reach the collector, causing an increase in current flow from emitter to collector and through external circuit.

Page 13: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 13

MOSFET (Metal-Oxide-Semiconductor Field Effect Transistor)

MOSFET transistor: two small islands of p-type semiconductor created within n-type silicon substrate. Islands connected by narrow p-type channel.

Metal contacts are made to islands (source and drain), one more contact (gate) is separated from channel by a thin (< 10 nm) insulating oxide layer.

Gate serves the function of the base in a junction transistor (electric field induced by gate controls current through the transistor)

Page 14: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 14

MOSFET (Metal-Oxide-Semiconductor Field Effect Transistor)

Voltage applied from source encourages carriers (holes in the case shown below) to flow from the source to the drain through the narrow channel.

Width (and hence resistance) of channel is controlled by intermediate gate voltage. For example, if positive voltage is applied to the gate, most of the holes are repelled from the channel and conductivity is decreasing.

Current flowing from the source to the drain is therefore modulated by the gate voltage (amplification and switching)

Page 15: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 15

Transistors and microelectronic devices

MOSFET dominates microelectronic industry (memories, microcomputers, amplifiers, etc.)

Large Si single crystals are grown and purified. Thin circular wafers (“chips”) are cut from crystals

Circuit elements are constructed by selective introduction of specific impurities (diffusion or ion implantation)

A single 8” diameter wafer of silicon can contain as many as 1010 - 1011 transistors in total

Cost to consumer ~ 0.00001c each.

Page 16: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 16

Conduction in Polymers and Ionic Materials

Ionic Materials

The band gap is large and only very few electrons can be promoted to the valence band by thermal fluctuations

Cation and anion diffusion can be directed by the electric field and can contribute to total conductivity: total = electronic + ionic

High temperatures produce Frenkel and Schottky defects which result in higher ionic conductivity.

Polymers Polymers are typically good insulators but can

be made to conduct by doping. A few polymers have very high electrical

conductivity - about one quarter that of copper, or about twice that of copper per unit weight.

Page 17: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 17

Capacitance

Voltage V applied to parallel conducting plates

plates charged by +Q, –Q

electric field E develops between plates

C depends on geometry of plates and material between plates

C = r o A / L = A / L

+ + + + +

- - - - - -

A is area of plates, L is distance between plates, is permittivity of dielectric medium, o is permittivity of a vacuum (8.85x10-12 F/m2), and r is relative permittivity (dielectric constant) of material, r = / o = C / Cvac

Ability to store charge capacitance

C = Q / V [Farads]

Charge can remain even after voltage removed.

Page 18: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 18

Dielectric Materials

Dielectric constant of vacuum is 1 and is close to 1 for air and many other gases. When piece of dielectric material is placed between two plates capacitance can increase significantly.

C = r o A / L

+ _

Dielectric is insulator in which electric dipoles are induced by electric field

with r = 81 for water, 20 for acetone, 12 for silicon, 3 for ice, etc.

+ _+ _

+_

Magnitude of electric dipole moment is p = q d

d

Page 19: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 19

Dielectric Materials

Dipole orientation along electric field in the capacitor causes charge redistribution.

Surface nearest to the positive capacitor plate is negatively charged and vice versa.

Dipole formation/alignment in electric field is called polarization P = Q’/A

Dipole alignment extra charge Q’ on plates:

Qt = |Q+Q’| now C = Qt / V

Increased capacitance r = C / Cvac > 1

+ + + + + + + +

- - - - - - - - -

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

-+

Q0 + Q’

-Q0 - Q’

region of nonet charge

net negative chargeat the surface, -Q’

net negative charge atthe surface, Q’ = PA

P

Page 20: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 20

Dielectric MaterialsSurface charge density (also called dielectric displacement) is

D = Q/A = r oE = oE + P

Polarization is responsible for the increase in charge density above that for vacuumMechanisms:dipole formation/orientation

electronic (induced) polarization: Electric field displaces negative electron “clouds” with respect to positive nucleus.

Ionic materials (induced) polarization: Applied electric field displaces cations and anions in opposite directions

molecular (orientation) polarization: Some materials possess permanent electric dipoles (e.g. H2O). In absence of electric field, dipoles are randomly oriented. Applying electric field aligns these dipoles, causing net (large) dipole moment.

Ptotal = Pe + Pi + Po

Page 21: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 21

Mechanisms of Polarization

electronic polarization

ionic polarization

molecular (orientation) polarization

Page 22: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 22

Dielectric Strength

Breakdown: high electric fields (>108 V/m) excite electrons to conduction band + accelerate them to high energies they collide with and ionize other electronsAvalanche process (or electrical discharge). Field necessary is called dielectric strength or breakdown strength.

Piezoelectricity (some ceramic materials)

Application of a force electric field (polarization) and vice-versa

Piezoelectric materials convert mechanical strain into electricity (microphones, strain gauges, sonar detectors)

Piezoelectric materials include barium titanate BaTiO3, lead zirconate PbZrO3, quartz.

Page 23: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 23

Nanoscopic materials design

The Center for Nanoscopic Materials Design at UVa

http://www.mrsec.virginia.edu/

Page 24: Introduction to Materials Science, Chapter 19, Electrical properties University of Virginia, Dept. of Materials Science and Engineering 1 Temperature variation

Introduction to Materials Science, Chapter 19, Electrical properties

University of Virginia, Dept. of Materials Science and Engineering 24

Summary

Acceptor state Capacitance Conduction band Conductivity, electrical Dielectric constant Dielectric displacement Dielectric strength Diode Dipole, electric Donor state Doping Electrical resistance Electron energy band Energy band gap Extrinsic semiconductor Fermi energy Forward bias Free electron Hole

Make sure you understand language and concepts:

Insulator Intrinsic semiconductor Ionic conduction Junction transistor Matthiessen’s rule Metal Mobility MOSFET Ohm’s law Permittivity Piezoelectric Polarization Polarization, electronic Polarization, ionic Polarization, orientation Rectifying junction Resistivity, electrical Reverse bias Semiconductor Valence band