iobp training manual - vibrating screen
TRANSCRIPT
PSSB - IOBP - Operation and Maintenance Manual REV. 0 MEI 2012
Beneficiation Plant
PSSB “Beneficiation Plant”
Vibrating Screen
Manual Instruction
TABLE OF CONTENTS 1. GENERAL 1
2. DESCRIPTION 3
3. HEALTH & SAFETY 10
4. FUNCTIONAL DESCRIPTION 14
5. CONTROL SYSTEM 24
6. INSTALLATION 25
7. COMMISSIONING 35
8. OPERATING INSTRUCTION 36
9. CARE & MAINTENANCE 42
10. SPARE PARTS 50
11. REFERENCES 53
12. APPENDICES 54
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 1 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
1. GENERAL
1.1 About this manual
1.2 Brochures
1.3 Contract data
1.4 Service & repair information
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 2 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
1. GENERAL
1.1 About this manual
Please read this introduction carefully before installation, using and
maintenance. This is the permanent technical documents of the screen, please keep it
well in case you use it at emergency.
For the purpose of mastering the use and maintenance, the manual provide
comprehensive and detailed information on the availability of such course. As we
seek continuous improvement of our Screen Machine, there may be a few
differences from the actual situation of machine, it is a normal phenomenon, sorry
for the inconvenience caused.
1.2 Brochures
1.3 Contract data
1.4 Service & repair information
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 3 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
2 DESCRIPTION
2.1 Equipment specification
2.2 Product design
2.3 Intended use
2.4 Design
2.5 Material and maximum working pressure
2.6 Paint specification
2.7 Dimensions
2.8 Performance
2.9 Certificates and test results
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 4 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
2. DESCRIPTION
The undersize screen refers to the screen with screen mesh less than 1 mm. in
the mineral and processing plant, it may be adopted as the equipment for such
operation as screening classification and dehydration. At the present, the undersize
screens utilized in the mineral processing plant are: fixed undersize screen, high
frequency vibration undersize screen, rectilinear vibration undersize screen, shaking
undersize screen, gyratory undersize screen and cyclone undersize screen. Therein
the high frequency undersize screen is applied the most extensively in the metallic
mineral processing plant and its vibrating modes are mainly divided into
electromagnetic vibration and shock excitation machine vibration. The screen
surfaces are mainly divided into metal woven meshes and nylon meshes. The
effective screening area of the metal woven mesh is large but it is easy to be worn
and its maintenance expense is large; the effective screening area of nylon mesh is
small but it is wear resistant and the maintenance expense is small. The shaking
undersize screen and gyratory undersize screen are mainly used for screening
classification of non-metal and coal.
There is a very large relation between the separation size and screen size selection so
that the suitability of the selected size will have a direct influence on the concentrate
grade and the productivity ratio. At the present, the relatively suitable example of its
application in domestic production is as follow:
Separation size/mm Screen size/mm
d1=0.044 s1=0.10
d2=0.063 s2=0.15
d3=0.074 s5=0.20
d4=0.10 s4=0.25
d5=0.15 s5=0.30
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 5 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
2.1 Equipment specification
Table 2.1: Technical parameters of each stage of high frequency undersize screen
equipment:
Working
name
Model and
specification
Quantity
(set)
Screen
box layer
number
Screen
surface
area (m2)
Installation
inclination
angle (°)
Total
power
(KW)
One –stage D5F1014 2 5 1.4 x 5 17.5 6.8
Two-stage D5F1014 2 5 1.4 x 5 17.5 6-8
2.1.1 Parameters of Multi-Stack Composite Vibrating Screen(D5MVSk1014d)
11.1. Electromagnetic vibration frequency: 50HZ;
11.2. Electromagnetic vibration Amplitude: 1~1.5mm;
11.3. Electromagnetic vibrating Power (Apparent Power): P1=2.8kW;
11.4. Electromagnetic vibration active power: P1'=0.52kW;
11.5. Screen Box linear vibrating frequency: 23HZ;
11.6. Screen Box linear vibrating amplitude: 1.5~2mm;
11.7. Vibrating Motor Power: P2=1.84×2=3.68kW;
11.8. Screen Box Inclination: 17.5°;
11.9. Feeding Particle size: ≤8mm;
11.10. Mineral Concentration Processing Capacity: 70~100t/h (Fine
Classification and dewatering)
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 6 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
2.2 Product design
Composite Vibrating Screen is a new type of solid material screening
equipment developed by LANDSKY TECH TANGSHAN CO.,LTD, it is a
composite vibration consists of the electromagnetic vibration(impact the sieve) and
the linear vibration of screen box. The machine has a high screening effici ency,
simplicity of operation, a stable performance, small power consumption, a small
dynamic load and a self-cleaning function.
This Multi-Stack Composite Vibrating Screen is mainly applicable for Wet
screening process and Dry screening process of fine materials, classification,
dewatering, desliming and Isolation of crude in different industries. Multi-Stack
Composite Vibrating Screen is newly developed from the normal MVS Series
Single-stack and Multi-Stack. It adopt the structure of Multi-Stack Screen, these 5
Stacks combine together to an integral unit and equipped with Vibrating Motors
which provide the power of screen box linear vibration to accomplish Composite
Vibration.
The model Numbers of Multi-Stacks Composite Vibrating Screens are showed as
follows:
D 5 F MVSk 10 14 d
Exciter type
Effective Sieving Length (dm)
Effective Sieving Width (dm)
Electromagnetic High Frequency Vibrating
Screen (Mineral Concentration)
Composite Vibration
Multi-Stack, Stacks of Screen Box
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 7 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
The appearance and installation size of all kinds of Multi-Stack Composite Vibrating
Screens, please find the weights in the General Assembly Drawing (Please find in
the Documents delivered with the machine)
2.3 Intended use
2.4 Design
Figure 1.1: Side View of Multi Stack Composite vibrating Screen D5FMVSk1014d
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 8 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 1.2: Typical Five Deck Derrick Stack Sizer
2.5 Material and maximum working pressure
2.6 Paint specification
2.7 Dimensions
2.8 Performance
Table 2.2: Technology indexes of undersize screen:
Working name Feed
concentration
Undersize
concentration
Oversize
concentration
Undersize
fineness -200
meshes %
One-stage 50 35 60 85
Two-stage 40 36 66 85
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 9 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
2.9 Certificates and test results
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 10 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
3 HEALTH AND SAFETY
3.1 General
3.2 Warning & caution sign
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 11 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
3. HEALTY AND SAFETY
3.1 General
3.2 Warning & caution sign
3.2.1 Personal Safety
Guards, covers and shields are installed around moving parts at the factory to
help protect from injury those working on or near the equipment. Do not modify or
eliminate safety devices installed at the factory. Make sure that everyone working on
or near the equipment is familiar with safety precautions. Owners and operators are
responsible for reading safety information and following safe practices. Think
safety! Act safely!
Wear a protective breathing mask whenever dust and fumes are
above acceptable limits.
Wear protective goggles or safety glasses with side shields to prevent
flying particles from entering eyes.
Hard hats can prevent injury and are required at most work sites. Be
sure to wear yours.
Do not remove any guards, covers or shields when equipment is running.
Replace any guards, covers or shields after adjustment or maintenance.
Never lubricate equipment when it is moving or running.
Report defective machinery and unsafe conditions to your supervisor.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 12 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Always look around equipment before start up to make sure no one is making
adjustments, pulling maintenance or standing close to moving parts. Always
know where your co-workers are.
3.2.2 Work Area Safety
Make certain all electrical equipment is properly grounded. Wet spots
near electric current are especially dangerous. Use ground- fault
interruptible circuits wherever potential shock hazard exists.
Be alert around any pressurized system, be it hydraulic or air. High-
pressure gases and oils can be very dangerous. Know your equipment
and operate it properly.
Know where fire extinguishers and other fire suppression equipment is
located. Learn how to use it.
Grounding connection is a must for the equipment, the Grounding
resistance should be less than 4 Ω, please find below Grounding
Position Drawing for reference (The machine is properly labeled)
Keep equipment clean and free of dirt and grease so it can be checked
for loose, cracked or broken parts. Replace defective parts as soon as
they are discovered.
Frequently check whether the ladder and safety handrail are firm and
reliable; timely handle and report problem found.
During equipment adjustable and checking, the obstructions above the
head, under the foot and all around shall be noted in order to prevent
slipping.
Keep the tread clean; when stepping up and down the ladder, holds
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 12 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Always look around equipment before start up to make sure no one is making
adjustments, pulling maintenance or standing close to moving parts. Always
know where your co-workers are.
3.2.2 Work Area Safety
Make certain all electrical equipment is properly grounded. Wet spots
near electric current are especially dangerous. Use ground- fault
interruptible circuits wherever potential shock hazard exists.
Be alert around any pressurized system, be it hydraulic or air. High-
pressure gases and oils can be very dangerous. Know your equipment
and operate it properly.
Know where fire extinguishers and other fire suppression equipment is
located. Learn how to use it.
Grounding connection is a must for the equipment, the Grounding
resistance should be less than 4 Ω, please find below Grounding
Position Drawing for reference (The machine is properly labeled)
Keep equipment clean and free of dirt and grease so it can be checked
for loose, cracked or broken parts. Replace defective parts as soon as
they are discovered.
Frequently check whether the ladder and safety handrail are firm and
reliable; timely handle and report problem found.
During equipment adjustable and checking, the obstructions above the
head, under the foot and all around shall be noted in order to prevent
slipping.
Keep the tread clean; when stepping up and down the ladder, holds
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 12 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Always look around equipment before start up to make sure no one is making
adjustments, pulling maintenance or standing close to moving parts. Always
know where your co-workers are.
3.2.2 Work Area Safety
Make certain all electrical equipment is properly grounded. Wet spots
near electric current are especially dangerous. Use ground- fault
interruptible circuits wherever potential shock hazard exists.
Be alert around any pressurized system, be it hydraulic or air. High-
pressure gases and oils can be very dangerous. Know your equipment
and operate it properly.
Know where fire extinguishers and other fire suppression equipment is
located. Learn how to use it.
Grounding connection is a must for the equipment, the Grounding
resistance should be less than 4 Ω, please find below Grounding
Position Drawing for reference (The machine is properly labeled)
Keep equipment clean and free of dirt and grease so it can be checked
for loose, cracked or broken parts. Replace defective parts as soon as
they are discovered.
Frequently check whether the ladder and safety handrail are firm and
reliable; timely handle and report problem found.
During equipment adjustable and checking, the obstructions above the
head, under the foot and all around shall be noted in order to prevent
slipping.
Keep the tread clean; when stepping up and down the ladder, holds
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 13 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
hands firmly and stand firmly. Starting electric switch with wet hand is
strictly forbidden to avoid electric shock.
It is strictly forbidden to start the equipment which is hung with
overhaul board.
Always use hoisting equipment for heavy loads. Regularly check
hooks, cables, shackles and chains for stretch and wear. Never
overload the lifting capacity of hoists, cranes and lifting devices.
Keep work area neat and as clean as practical.
Keep all warning and caution signs clear and up to date.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 14 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4. FUNCTIONAL DESCRIPTION
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 15 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4. FUNCTIONAL DESCRIPTION
4.1 Operational Principle and Structure Characteristics
4.1.1 Operational Principle of Multi-Stack Composite Vibration Screen
The slurry consisting of water and process material is equally distributed to the
dedicated feeders that supply each screen frame. The vibratory action of the motors
provided the G-forces required facilitate the screening processes.
Water and undersize particles pass through each screen panel and flow into an
undersize collection pan. A duct at the lowest part of the pan empties into undersize
manifold that carries the material to the undersize discharge flange. The vibration
conveys larger particles along the top surfaces of the screen panels to the end where
they fall off into the oversize hopper. Oversize material is then discharge through the
flanged port on the undersize of the oversize hopper.
Re-pulp machines are a replaceable rubber-lined re-pulp tray and spray bar between
each screen section. The spray bars continually disperse water into the re-pulp trays
to add free water to the screening operation (Figure 3). This free water facilitates
separation of the undersize material, allowing it to pass through the screen surface
unhindered, thereby increasing the screening efficiency. By utilizing the transitional
area between the two screen panels for the re-pulp process, screening efficiency is
increase without increasing length of the deck.
Figure 4.1: Re-pulp tray operation
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 16 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
As for MVS electromagnetic vibration HF vibrating screen, its parameter are
centralized and controlled by adopting the computer controlled cabinet and the
vibration frequency may be alternating. Under the program control, the control, the
vibration frequency may be automatically switched as 25HZ and 50Hz, and it may
also be fixed frequency as 25Hz and 50Hz. additionally, the vibration parameters of
the each vibration system may be prepared by software; the vibrating arm and
vibrating screen surface of each vibration system are driven separately and
respectively; the amplitude may be adjusted in segments at any time. Except for
vibration parameters of general operating conditions, the parameter of the
discontinuous instant strong vibration is also needed to clean the screen surface at
any time so as to keep the screen mesh unblocked and improve the working
efficiency.
It has the following characteristics over other undersize screens:
1. There is no rotary part and there is no need to apply lubricating oil.
2. Its structure is simple so that it is convenient for maintenance, its structural
durability is good and the failure rate is low.
3. The resonance principle is applied for the vibrator, it is worked in double
body critical resonance state and the required driving power is small, so there
is no large pickup current and the noise is low when it is started.
4. After starting the vibrator, the amplitude may reach the operation stable
value instantaneously. When it is shut down, its amplitude may disappear
instantaneously. It is allowed to be directly started or shut down under rate d
voltage, current and amplitude.
5. The shock excitation or amplitude of the screen frame is adjustable. The
particle size (namely,-200 mesh percentage content) of the undersize product
may be controlled by changing the exciting force of the screen frame
(adjusting the power supply of the shock excitation). It is very beneficial to
guarantee the concentrate grade of the ore in different crystal sizes.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 17 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6. At the same time of screen frame vibration, the relative vibration also
generates between screen bars of the screen sheet and the screen sheet gap is
difficult to be blocked.
7. On the condition that only start the electromagnetic exciter(The exciter is
mounted inside the box of sideboard of screen box), Alternating current
magnetic force is conveyed to main vibrating screen, force transmission
bolts, vibrating rod and vibrating shaft as the power of make the vibrating
arm under the sieve do a reciprocating swing, the vibration brought by the
vibrating cap in the top of vibrating arm support and impact the sieve whil e
the screen box almost not move, the vibrating system is working under near
resonant condition, only a smaller power is needed for reaching the specified
operation parameter. The screen mesh is vibrated at a high vibrating strength,
and the vibration intensity is 8-10 times that of the acceleration gravity. 2-3
times that of the common vibrating screens. The screen has a high screening
efficiency and a high throughput capacity. Each electromagnetic exciter has
small power consumption; the active power is only 130W. So model of
screen is high performance energy saving product, each screen box has
several vibrating systems in the longitudinal direction(length direction),
which driven by the exciter to impact the Screen Mesh, the screen mesh is
vibrated at a high frequency of 50HZ,the vibrating parameters are regulated
by the control cabinet.
On the condition that only start the vibrating motor, 5 Stacks screen boxes is doing
an integral linear vibration to achieve composite vibration to the screen mesh.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 18 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.2 Overall Structure of Multi-Stack Composite Vibrating Screen (As shown in
Drawing)
1 Screen Box
1.1 Mesh
1.2 Hook Plate sealing type
3 Control Cabinet
4.3.4 Oversize Collection
4.3.5 Undersize Collection
5 Feeding Box
8 Frames
10 Slurry Distributors
Figure 4.2: Drawing of Multi Stack Composite Vibrating Screen
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 18 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.2 Overall Structure of Multi-Stack Composite Vibrating Screen (As shown in
Drawing)
1 Screen Box
1.1 Mesh
1.2 Hook Plate sealing type
3 Control Cabinet
4.3.4 Oversize Collection
4.3.5 Undersize Collection
5 Feeding Box
8 Frames
10 Slurry Distributors
Figure 4.2: Drawing of Multi Stack Composite Vibrating Screen
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 18 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.2 Overall Structure of Multi-Stack Composite Vibrating Screen (As shown in
Drawing)
1 Screen Box
1.1 Mesh
1.2 Hook Plate sealing type
3 Control Cabinet
4.3.4 Oversize Collection
4.3.5 Undersize Collection
5 Feeding Box
8 Frames
10 Slurry Distributors
Figure 4.2: Drawing of Multi Stack Composite Vibrating Screen
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 19 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Table 4.1
Figure 4.3: Major component of Derrick’s Stack Sizer
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 19 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Table 4.1
Figure 4.3: Major component of Derrick’s Stack Sizer
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 19 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Table 4.1
Figure 4.3: Major component of Derrick’s Stack Sizer
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 20 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.3 Structure and Characteristic
Multi-Stack Composite Vibrating Screen shows the advantage in occupying smaller
areas and a high screening efficiency, each electromagnetic vibration of screen box
could be controlled respectively, Multi-Stack screen boxes is doing a integral linear
vibration, each screen box could be fed separately and evenly spread. Oversize and
Undersize materials are collected separately with no interference.
4.3.1 Screen Box
Screen Box consists of Frame, Mesh, Exciter, Transmission System, Hook Plate and
Vibrating Motor.
The model numbers of Multi-Stack Composite Vibrating Screen is reflected in the
numbers of Screen Box and Structure. The numbers of Screen Box decide the
numbers of Stack, each electromagnetic vibration of screen box could be controlled
respectively, each screen box has two exciters, two coils inside each exciter are
parallel connection which could be adjusted by a knob, Intermittent strong vibrating
is also set for screen mesh, cleaning the mesh at periodical time so as to keep the
screen mesh unclogged. The arc shape surface of mesh is helpful to uniform
distribution and increase of utilization ratio.
The function of vibration motor is to bring linear vibration of screen box ass embly,
increase screening efficiency and processing capacity.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 21 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.3.1.1Mesh
The mesh consists of three layers. The bottom layer is a supporting mesh which
contact the vibrating cap, normally adopt Steel Wire Core Polyurethane Mesh or
Large Aperture Steel Wire Mesh, it play a role of protect the Working Mesh. The
top layer contact the materials is Working Mesh which consist of two layers of mesh
vulcanized together by rubber with different aperture sizes, it has a lightweight and a
high opening rate.
Figure 4.4
Figure 4.5
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 21 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.3.1.1Mesh
The mesh consists of three layers. The bottom layer is a supporting mesh which
contact the vibrating cap, normally adopt Steel Wire Core Polyurethane Mesh or
Large Aperture Steel Wire Mesh, it play a role of protect the Working Mesh. The
top layer contact the materials is Working Mesh which consist of two layers of mesh
vulcanized together by rubber with different aperture sizes, it has a lightweight and a
high opening rate.
Figure 4.4
Figure 4.5
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 21 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.3.1.1Mesh
The mesh consists of three layers. The bottom layer is a supporting mesh which
contact the vibrating cap, normally adopt Steel Wire Core Polyurethane Mesh or
Large Aperture Steel Wire Mesh, it play a role of protect the Working Mesh. The
top layer contact the materials is Working Mesh which consist of two layers of mesh
vulcanized together by rubber with different aperture sizes, it has a lightweight and a
high opening rate.
Figure 4.4
Figure 4.5
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 22 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
1 Shaped Bolt
2 Nut
3 Large Washer
4 Rubber Compression Spring
5 Cushion Block
6 Sideboard
7 Side Hook Plate
8 Working Mesh
9 Supporting Mesh
10 Retractor Plate
4.3.1.2 Hook Plate sealing type
The Working Mesh and Supporting Mesh of Multi-Stack Composite Vibrating
Screen are tightly stretched in transverse direction by hook plate; the meshes also
could be sealed while stretched. The structure as shown below:
Figure 7
4.3.2 Frame
The frame is frame structure overall welded with channel beam, it play a role of
support screen box assembly.
4.3.3 Feeding Box
Convey raw materials, provide a uniform distribution, and make the best of
screening.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 22 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
1 Shaped Bolt
2 Nut
3 Large Washer
4 Rubber Compression Spring
5 Cushion Block
6 Sideboard
7 Side Hook Plate
8 Working Mesh
9 Supporting Mesh
10 Retractor Plate
4.3.1.2 Hook Plate sealing type
The Working Mesh and Supporting Mesh of Multi-Stack Composite Vibrating
Screen are tightly stretched in transverse direction by hook plate; the meshes also
could be sealed while stretched. The structure as shown below:
Figure 7
4.3.2 Frame
The frame is frame structure overall welded with channel beam, it play a role of
support screen box assembly.
4.3.3 Feeding Box
Convey raw materials, provide a uniform distribution, and make the best of
screening.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 22 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
1 Shaped Bolt
2 Nut
3 Large Washer
4 Rubber Compression Spring
5 Cushion Block
6 Sideboard
7 Side Hook Plate
8 Working Mesh
9 Supporting Mesh
10 Retractor Plate
4.3.1.2 Hook Plate sealing type
The Working Mesh and Supporting Mesh of Multi-Stack Composite Vibrating
Screen are tightly stretched in transverse direction by hook plate; the meshes also
could be sealed while stretched. The structure as shown below:
Figure 7
4.3.2 Frame
The frame is frame structure overall welded with channel beam, it play a role of
support screen box assembly.
4.3.3 Feeding Box
Convey raw materials, provide a uniform distribution, and make the best of
screening.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 23 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
4.3.4 Oversize Collection
Trough is used to collect the oversized materials of each screen box.
4.3.5 Undersize Collection
Trough is used to collect the undersized materials of each screen box, it will be
bolted with the Oversize Collection Trough together as an integral unit.
4.3.6 Control Cabinet
The Multi-Stack Composite Vibrating Screen adopted Microcomputer Digital
Control System, it has Soft-Start type, a reliable performance, a simplicity operation
and easy maintenance. The vibrating parameters could be regulated by control
cabinet, please find the details in 《LK-MVS Digital Control Screening System
Cabinet Operation Manual》
4.3.7 Slurry Distributor
Slurry Distributor is used to supply materials to each feeding box of screen machine,
the Feeding Box and Slurry Distributor are connected by hose, make sure there is a
tilt angle with the hose, the position of Slurry Distributor Frame is determined
according to the site conditions.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 24 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
5. CONTROL SYSTEM
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 25 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6 INSTALLATION
6.1 Delivery, handling and storage
6.2 Foundation requirements
6.3 Installation tools and equipment
6.4 Installation procedure
6.5 Pipe connections and pump sump
6.6 Shaft gland
6.7 Motor and drive
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 26 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6. INSTALLATION
6.1 Delivery, handling and storage.
1. Basic principles of storage is to protect the paint layer, cladding material and
coating layer covered the surface of screen’s parts, prevent corrosion,
deformation and mechanical properties change of the parts, and keep the
effective continuity.
2. During the loading and unloading, the hanging should be accorded with hoisting
position indicated on wrap page. Fibre lifting belt should be used to prevent
damage to overcoat if paint surface or coating layer touched.
3. Storing and placing shall be complied with packaging requirements or refer to
relevant standards, wrapping object can only be touched each other to avoid
direct contact with the surface causing deformation or damage to component
part surface.
4. During storage, parts with rubber springs, should ensure that their state is not in
strained condition, to prevent early failure or performance changes of rubber
springs. And the rubber spring should avoid contacting with the materials with
erosion effect to rubber, such as oil and organic solvents.
5. The rubber spring of screen’s component parts should be sealed and dark
storage.
6. Storage location of component parts should avoid direct sunlight to prevent parts
aging or paint fading, able to effectively prevent invasion of rain, snow and
water, and maintain good ventilation. The location temperature is no less than
5℃, and the relative humidity is no more than 60%, otherwise, the vibrating
motor should be removed to keep in other place.
7. Storage conditions and maintenance of electrical control cabinet with special
packaging should be implemented in accordance with "electrical control cabinet
manual".
8. Spare parts kit and special tools’ box should be stored in ventilated, dry, and
shade place.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 27 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9. Composite mesh and polyurethanes mesh (PU mesh) should be avoided mixes
puts with oil or organic solvent, and placed horizontally, packaging should be
able to effectively prevent the mesh deformation by weight pressure.
6.2 Foundation requirements
6.2.1 Preparation for Installation
Infrastructure must meet the requirements, able to withstand greater
than various load on the foundation of screen foot. Load on the foundation of screen
foot:
Feeding end:
Dynamic load of regular work:
Horizontal dynamic load (Lengthways) N,
Vertical dynamic load N;
Resonating dynamic load of screen’s start and stop:
Horizontal dynamic load (Lengthways) N,
Vertical dynamic load N.
Vertical static load: N.
Discharge end:
Dynamic load of regular work:
Horizontal dynamic load (Lengthways) N,
Vertical dynamic load N;
Resonating dynamic load of screen’s start and stop:
Horizontal dynamic load (Lengthways) N,
Vertical dynamic load N.
Vertical static load: N.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 28 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.2.2 Long term storage
If storage period of rubber spring is more than 6 months, before installation each
spring should be carefully examined, checking the hardness, elasticity, with or
without aging and so on, the one that performance indicators do not meet the
requirements must be replaced. Rubber spare parts in a sealed, dark storage after 24
months must be carried out a performance test before using, it cannot
be installed or used except the test result meet the requirements.
Table 6.1: Rubber spares must meet the following performance indicators:
Item Hardness Appearance Fix location
Main vibrating spring 42
No significant deformation
and damage
Hinge spring 83����
Transmission linkage
place
Hinge axis spring 62 Both ends of
vibrating bar
Shear rubber spring 45����
Damping rubber
block
55����
6.3 Installation tools and equipment
6.3.0 Installation of multi-stack composite vibrating screen
All the packaging and holder for transport protection should be removed
before screen installation.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 28 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.2.2 Long term storage
If storage period of rubber spring is more than 6 months, before installation each
spring should be carefully examined, checking the hardness, elasticity, with or
without aging and so on, the one that performance indicators do not meet the
requirements must be replaced. Rubber spare parts in a sealed, dark storage after 24
months must be carried out a performance test before using, it cannot
be installed or used except the test result meet the requirements.
Table 6.1: Rubber spares must meet the following performance indicators:
Item Hardness Appearance Fix location
Main vibrating spring 42
No significant deformation
and damage
Hinge spring 83����
Transmission linkage
place
Hinge axis spring 62 Both ends of
vibrating bar
Shear rubber spring 45����
Damping rubber
block
55����
6.3 Installation tools and equipment
6.3.0 Installation of multi-stack composite vibrating screen
All the packaging and holder for transport protection should be removed
before screen installation.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 28 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.2.2 Long term storage
If storage period of rubber spring is more than 6 months, before installation each
spring should be carefully examined, checking the hardness, elasticity, with or
without aging and so on, the one that performance indicators do not meet the
requirements must be replaced. Rubber spare parts in a sealed, dark storage after 24
months must be carried out a performance test before using, it cannot
be installed or used except the test result meet the requirements.
Table 6.1: Rubber spares must meet the following performance indicators:
Item Hardness Appearance Fix location
Main vibrating spring 42
No significant deformation
and damage
Hinge spring 83����
Transmission linkage
place
Hinge axis spring 62 Both ends of
vibrating bar
Shear rubber spring 45����
Damping rubber
block
55����
6.3 Installation tools and equipment
6.3.0 Installation of multi-stack composite vibrating screen
All the packaging and holder for transport protection should be removed
before screen installation.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 29 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.4 Installation procedure
6.4.1 Installation of chute overs and unders
Chute of overs and unders are assembled at the factory as a whole, not required to
separate while installing, after bottom case installation completed, put the chute on
the square hole of install base (see Figure xx) , and then place “group of frame,
screen box and feed box” on the chute, last fasten the connector through the frame
and the chute. (See overall structure: Figure xx.)
6.4.2 Installation of screen frame, box group and feed box
Before install, remove stationary bush between frame group and screen
box group, gasket between connection beam and frame, and tighten the
connection bolts as well as the bolts combined the shear rubber spring
with frame and screen box. Then remove the secondary support pole.
The frame group and box group are assembled at the factory as a whole connected
by shear rubber spring, feed box is connected with side frame column, and position
of the feed box can be adjusted through change the height of support hole, and
feed box is joined with connection angle steel as one. (See Figure 4)
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 29 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.4 Installation procedure
6.4.1 Installation of chute overs and unders
Chute of overs and unders are assembled at the factory as a whole, not required to
separate while installing, after bottom case installation completed, put the chute on
the square hole of install base (see Figure xx) , and then place “group of frame,
screen box and feed box” on the chute, last fasten the connector through the frame
and the chute. (See overall structure: Figure xx.)
6.4.2 Installation of screen frame, box group and feed box
Before install, remove stationary bush between frame group and screen
box group, gasket between connection beam and frame, and tighten the
connection bolts as well as the bolts combined the shear rubber spring
with frame and screen box. Then remove the secondary support pole.
The frame group and box group are assembled at the factory as a whole connected
by shear rubber spring, feed box is connected with side frame column, and position
of the feed box can be adjusted through change the height of support hole, and
feed box is joined with connection angle steel as one. (See Figure 4)
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 29 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
6.4 Installation procedure
6.4.1 Installation of chute overs and unders
Chute of overs and unders are assembled at the factory as a whole, not required to
separate while installing, after bottom case installation completed, put the chute on
the square hole of install base (see Figure xx) , and then place “group of frame,
screen box and feed box” on the chute, last fasten the connector through the frame
and the chute. (See overall structure: Figure xx.)
6.4.2 Installation of screen frame, box group and feed box
Before install, remove stationary bush between frame group and screen
box group, gasket between connection beam and frame, and tighten the
connection bolts as well as the bolts combined the shear rubber spring
with frame and screen box. Then remove the secondary support pole.
The frame group and box group are assembled at the factory as a whole connected
by shear rubber spring, feed box is connected with side frame column, and position
of the feed box can be adjusted through change the height of support hole, and
feed box is joined with connection angle steel as one. (See Figure 4)
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 30 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 6.1
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 31 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
S/N SPECIFICATION NAME QUANTITY
1 D5F1014d10.01 Box group 1
2 D5F1014d10.04 Frame 1
3 D5F1014d10.05 Feed box 5
4 D5F1014d10-01
Angle steel for
connection
2
5 GB/T5871-2000 Bolt M16×45 30
6 GB/T41-2000 Nut M16 66
7 GB95-1985 Cushion 16 30
8 GB93-1987 Washer 16 66
9 GB/T93-1987 Washer 12 88
10 GB/T5873-2000 Bolt M12×30 88
11 D5F1014d10.08 Shear rubber spring
spares
22
6.4.3 Installation of mesh
The mesh is horizontally tensioned in screen box, there are two working
meshes and two support meshes on each screen box. First put hook of support mesh
parallel to the side plate, hook downward, the mesh is tiled on the vibrating cap, one
end of the hook is fixed on the angle steel of screen box, the other end with hooks is
buckled together with retractor plate, shaped bolts are passed through the position
block, and rubber spring, a large washer, nut, and o-rubber seal installed in turn,
equably tighten the nut on the retractor plate hooks, and tension the support mesh.
Second put hook of working mesh parallel to the side plate, hook upward, tiled on
the support mesh, note that working mesh should be put in p roper direction, the
mesh strengthening part with vulcanized rubber must correspond to polyurethane
vibrating cap below the support mesh. After mesh positioning, buckle the
hooks together with retractor plate on the sides of screen box, shaped bolts are
passed through the position block, and rubber spring, a large washer, nut, and o-
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 32 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
rubber seal installed in turn, equably tighten the nut on the retractor plate hooks, and
tension the working mesh. (See figure 3)
Note: the mesh must be paved and proper tension while installed, distorted folds and
other surface irregular must be avoided, so as not to affect the mesh life
or screening effect. While tightening shaped bolts, screwed degree of both sides
should be consistent with the symmetry to prevent deflection of the mesh installation
location. Compression amount of the rubber spring is 1~2mm,
excessive compression will damage normal function of the rubber spring.
When replacing the mesh, shaped bolt shall not be pulled out, just rotated direction
to ensure retractor plate can be taken out.
6.4.4 Access of electric control cabinet
Cable air plugs are inserted into plug seat inside the cabinet, ensuring good
contact and tightening the clips. The power wires are soldered to terminals in.
More use and maintenance information, see "The manual of electric control cabinet
mate with LK-MVS digital control screening system ".
Note: pay attention to the following terms while installation
1. This device must be connected to protective earth, grounding resistance is
less than 4ohms. The screen should be installed ground wire in accordance
with the ground sign location.
2. The control cabinet should be placed in dry and dust-free place, and
be protective, to avoid the vibration and shock. Placed in the open
place, water washout, dust and other harsh conditions are prohibited.
3. A cable from two parallel coils from one exciter on the side of screen is
called one route, some routes are converge in junction box. Usually the
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 33 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
length of the cable from junction box to the control cab inet is10 meters while
leaving factory (according to the customers’ needs, the length can be
changed before leaving factory), and the cable should be placed on cable
racks to be protected from damage.
Warning! Incorrect tightening will cause improper screen panel
tensioning, resulting in premature wear. Be sure that correct tightening
sequence is followed.
Figure: Check panel tension by lifting the edge
Figure: Check for straight alignment of panel ribs with stringer protectors.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 33 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
length of the cable from junction box to the control cab inet is10 meters while
leaving factory (according to the customers’ needs, the length can be
changed before leaving factory), and the cable should be placed on cable
racks to be protected from damage.
Warning! Incorrect tightening will cause improper screen panel
tensioning, resulting in premature wear. Be sure that correct tightening
sequence is followed.
Figure: Check panel tension by lifting the edge
Figure: Check for straight alignment of panel ribs with stringer protectors.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 33 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
length of the cable from junction box to the control cab inet is10 meters while
leaving factory (according to the customers’ needs, the length can be
changed before leaving factory), and the cable should be placed on cable
racks to be protected from damage.
Warning! Incorrect tightening will cause improper screen panel
tensioning, resulting in premature wear. Be sure that correct tightening
sequence is followed.
Figure: Check panel tension by lifting the edge
Figure: Check for straight alignment of panel ribs with stringer protectors.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 34 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure: Check for consistent number of exposed treads on all draws bolts.
6.5 Pipe connections and pump sump
6.6 Shaft gland
6.7 Motor and drive
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 35 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
7. COMMISSIONING
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 36 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
8 OPERATING INSTRUCTION
8.1 Start -up
8.2 Shutdown
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 37 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
8. OPERATING INSTRUCTION
Once installed, screw tightness and block should be checked, make sure there is no
obstacle to the movements of Multi-Stack Composite Vibrating Screen. Turn on the
current to achieve the start condition. Please find the Electrical Operation at 《LK-
MVS Digital Control Screening System Cabinet Operation Manual》
8.1 Start –up
Re-lubrication should be done if there are more than 24 months since the date of
manufacturer of Vibrating Motor. The operation should be in compliance with
‘Vibrating Screen Operation Manual’.
Hours Empty Running should be done to observe the operation status before
production run. Smooth running or not, is there a strong vibration.
The displayed data are same as the sequence of exciters respectively, and
accomplished independent control. Adjust the amplitude gradually and check
whether the changes of increase and reduce are in compliance with the operations.
Are there any abnormal noises, especially is there any metal impact sound between
Magnetic Plug and Armature inside the box of exciters. If so, please adjust it.
The adjustment of Electromagnetic Exciters: The space between Magnetic Plug and
Armature named Air Gap δ, δ play an important role in the running of Screen
Machine. Normally, δ should be confined between 2.0 – 2.5mm, the vibration force
will be difficult to meet the operating requirements if the δ is too big; It will incur
metal impact sound between Magnetic Plug and Armature if the δ is too small. All
the exciters had been adjusted to its optimum condition before delivery. Amplitude
is set at 70% - 80%, and the amplitude of sieve is set at 1.5 – 2.0mm, the period of
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 38 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Transient Vibration is 3 second. The interval of Transient Vibration could be regulated
from 12 seconds to 6 minutes.
Prolong the life of vibrating parts and sieves by making the most of small
amplitude in normal operation.
Variation of δ incurred by vibration or other reason. Check whether the Compression of
Main Vibrating Spring is in the range of 2.0 – 2.5mm when there is δ variation, change
the δ by adjusting Compression of Main Vibrating Spring, and regulate the Air Gap
between clamp and exciter to change the δ if it is still not in the range of 2.0 – 2.5mm
after above procedure. The specific method is to lose the bolt of c lamp in order that
make more space between clamp and the box of exciter, and insert the washers inside
the gap.(The thickness of washer is 0.3mm, please find Drawing -5 for your reference).
Figure 8.1
Warning: Shutdown the machine before adjusts δ, unplug the power. Power
operation is prohibited during adjustment.
After a while of operation, the surface temperature of coil increase to
maximum 50℃, and the temperature of screen box is also high, please do not
touch it to prevent from burned.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 38 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Transient Vibration is 3 second. The interval of Transient Vibration could be regulated
from 12 seconds to 6 minutes.
Prolong the life of vibrating parts and sieves by making the most of small
amplitude in normal operation.
Variation of δ incurred by vibration or other reason. Check whether the Compression of
Main Vibrating Spring is in the range of 2.0 – 2.5mm when there is δ variation, change
the δ by adjusting Compression of Main Vibrating Spring, and regulate the Air Gap
between clamp and exciter to change the δ if it is still not in the range of 2.0 – 2.5mm
after above procedure. The specific method is to lose the bolt of c lamp in order that
make more space between clamp and the box of exciter, and insert the washers inside
the gap.(The thickness of washer is 0.3mm, please find Drawing -5 for your reference).
Figure 8.1
Warning: Shutdown the machine before adjusts δ, unplug the power. Power
operation is prohibited during adjustment.
After a while of operation, the surface temperature of coil increase to
maximum 50℃, and the temperature of screen box is also high, please do not
touch it to prevent from burned.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 38 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Transient Vibration is 3 second. The interval of Transient Vibration could be regulated
from 12 seconds to 6 minutes.
Prolong the life of vibrating parts and sieves by making the most of small
amplitude in normal operation.
Variation of δ incurred by vibration or other reason. Check whether the Compression of
Main Vibrating Spring is in the range of 2.0 – 2.5mm when there is δ variation, change
the δ by adjusting Compression of Main Vibrating Spring, and regulate the Air Gap
between clamp and exciter to change the δ if it is still not in the range of 2.0 – 2.5mm
after above procedure. The specific method is to lose the bolt of c lamp in order that
make more space between clamp and the box of exciter, and insert the washers inside
the gap.(The thickness of washer is 0.3mm, please find Drawing -5 for your reference).
Figure 8.1
Warning: Shutdown the machine before adjusts δ, unplug the power. Power
operation is prohibited during adjustment.
After a while of operation, the surface temperature of coil increase to
maximum 50℃, and the temperature of screen box is also high, please do not
touch it to prevent from burned.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 39 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.2
The force transmission bolt assembly of Armature consists of two positioning
blocks in the upper and bottom positions respectively, the upper side of the
positioning block is steel plate, and the bottom side is rubber. The rubber side leans
against the Silicon Steel Sheet of force transmission bolt assembly, another side is
screwed to the screen box. Loose the bolt of positioning block before adjust the Air
Gap, fasten the bolt of positioning block after adjustment and tight the nut. The
compression of positioning block should be confined in the range of 1 – 2mm, the
service life will be reduced if it is compressed too tight.
The General Principle is: The Air Gap should be as small as possible on the promise
of required amplitude and no impact between Magnetic Plug and Armature. On the
promise of normal operation, use low current and small amplitude as far as possible,
long interval of Transient Vibration to prevent the sieve and vibrating parts f rom
damage caused by vibration.
Make sure there is no difference with vibrations of different vibrating caps. Check
whether the vibrating cap is closely tied up the sieve, loose the fixing bolt on the
vibrating arm if there is some space between the vibrating cap and the sieve, turn the
vibrating shaft to adjust the position of vibrating cap to tie up the sieve, then tighten
the screw. (As shown in drawing below).
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 39 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.2
The force transmission bolt assembly of Armature consists of two positioning
blocks in the upper and bottom positions respectively, the upper side of the
positioning block is steel plate, and the bottom side is rubber. The rubber side leans
against the Silicon Steel Sheet of force transmission bolt assembly, another side is
screwed to the screen box. Loose the bolt of positioning block before adjust the Air
Gap, fasten the bolt of positioning block after adjustment and tight the nut. The
compression of positioning block should be confined in the range of 1 – 2mm, the
service life will be reduced if it is compressed too tight.
The General Principle is: The Air Gap should be as small as possible on the promise
of required amplitude and no impact between Magnetic Plug and Armature. On the
promise of normal operation, use low current and small amplitude as far as possible,
long interval of Transient Vibration to prevent the sieve and vibrating parts f rom
damage caused by vibration.
Make sure there is no difference with vibrations of different vibrating caps. Check
whether the vibrating cap is closely tied up the sieve, loose the fixing bolt on the
vibrating arm if there is some space between the vibrating cap and the sieve, turn the
vibrating shaft to adjust the position of vibrating cap to tie up the sieve, then tighten
the screw. (As shown in drawing below).
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 39 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.2
The force transmission bolt assembly of Armature consists of two positioning
blocks in the upper and bottom positions respectively, the upper side of the
positioning block is steel plate, and the bottom side is rubber. The rubber side leans
against the Silicon Steel Sheet of force transmission bolt assembly, another side is
screwed to the screen box. Loose the bolt of positioning block before adjust the Air
Gap, fasten the bolt of positioning block after adjustment and tight the nut. The
compression of positioning block should be confined in the range of 1 – 2mm, the
service life will be reduced if it is compressed too tight.
The General Principle is: The Air Gap should be as small as possible on the promise
of required amplitude and no impact between Magnetic Plug and Armature. On the
promise of normal operation, use low current and small amplitude as far as possible,
long interval of Transient Vibration to prevent the sieve and vibrating parts f rom
damage caused by vibration.
Make sure there is no difference with vibrations of different vibrating caps. Check
whether the vibrating cap is closely tied up the sieve, loose the fixing bolt on the
vibrating arm if there is some space between the vibrating cap and the sieve, turn the
vibrating shaft to adjust the position of vibrating cap to tie up the sieve, then tighten
the screw. (As shown in drawing below).
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 40 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.3
8.2 Shutdown
Shutdown the machine after 4 hours running, check the temperature rise of Magnetic
Plug coil, it should not exceed 50℃. Make sure the entire bolt are tightened,
especially the connecting bolts between the vibrating arm and vibrating shaft, it will
influence the vibrating effect if not tight.
Stop feeding before shutting down, stop the machine after all oversized materials
had been cleaned up. The sieve should be protected properly, no tread and strike on
the surface of sieve by iron and other hard objects. Flush by clean water and wash by
nylon brush when clogging.
Regulate the surface amplitudes of each sieve by adjusting the amplitude of exciter
respectively as feeding required.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 40 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.3
8.2 Shutdown
Shutdown the machine after 4 hours running, check the temperature rise of Magnetic
Plug coil, it should not exceed 50℃. Make sure the entire bolt are tightened,
especially the connecting bolts between the vibrating arm and vibrating shaft, it will
influence the vibrating effect if not tight.
Stop feeding before shutting down, stop the machine after all oversized materials
had been cleaned up. The sieve should be protected properly, no tread and strike on
the surface of sieve by iron and other hard objects. Flush by clean water and wash by
nylon brush when clogging.
Regulate the surface amplitudes of each sieve by adjusting the amplitude of exciter
respectively as feeding required.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 40 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 8.3
8.2 Shutdown
Shutdown the machine after 4 hours running, check the temperature rise of Magnetic
Plug coil, it should not exceed 50℃. Make sure the entire bolt are tightened,
especially the connecting bolts between the vibrating arm and vibrating shaft, it will
influence the vibrating effect if not tight.
Stop feeding before shutting down, stop the machine after all oversized materials
had been cleaned up. The sieve should be protected properly, no tread and strike on
the surface of sieve by iron and other hard objects. Flush by clean water and wash by
nylon brush when clogging.
Regulate the surface amplitudes of each sieve by adjusting the amplitude of exciter
respectively as feeding required.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 41 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Table 8.1 shown normal shut down procedure shall be followed each time the
equipment is shut down for maintenance and/or changing of screen panels:
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 42 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9 CARE AND MAINTENANCE
9.1 Running checks
9.2 Preventive maintenance & service schedule
9.3 Fault finding
9.4 Lubrication
9.5 Dismantling and assembly
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 43 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9. CARE AND MAINTENANCE
9.1 Running checks
Routine maintenance will ensure maximum life and trouble-free operation.
While the maintenance schedule presented in this section is flexible, modifications
should be based on experience with operating the equipment at your facilities. A
maintenance log should be kept to help establish a routine maintenance schedule, as
well as to monitor and adjust the schedule as necessary throughout the equipm ent’s
life.
Consider the following factors when establishing a maintenance schedule:
Duty cycle
Ambient temperature
Operating environment
9.1.1 Routine maintenance
Routine maintenance consists of overall inspection and cleaning.
Table 9.1: The following table lists the recommended routine maintenance
procedures
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 44 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9.1.2 Screen Frames
All screen frames include screen tensioning components and the mounting surface for
the screen panels. The upper screen frame (Figure _) also includes mounting provisions for
the vibrator motors. The screen frames are suspended between the side support channels.
During normal operation, the screen frames and tensioning components accumulate residual
mud that should be removed periodically. When replacing stringer protectors a snug fit
against the cross supports but without causing any buckling. After instal lation confirm that
protectors lie flat and no gaps are present between ends of protectors and cross supports.
In addition, the float mounts should be inspected and replaced when damage is evident. Since
these components isolate the vibratory motion of the screen frames from stationary parts of
the machine, deterioration may occur over time.
Figure 9.1: Screen frames and associate components
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 45 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Table 9.2
9.2 Preventive maintenance & service schedule
9.2.1 Exciter In operation a)Check the power supply, fuse and coil
b)Check the condition of circuit board is there any loosing or damage.
c)Check the arraying cables contacted properly or not.
d)Make sure the setting of Control Cabinet is correct.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 46 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9.2.2 Displayed amplitude is big while real amplitude is small.
a)Air Gap is too big
b) The type of vibration setting is correct or not
c)Is there any block with the parts of machine.
9.2.3 Small amplitude
Increase the amplitude by adjusting the control cabinet, reduce the δ
9.2.4 Abnormal Metal Clashing a)Adjust the amplitude if it is too big
b)Uneven Air Gap or too small
c)Loosing inside the exciter by offset
9.3 Fault finding
Rapid change draw bolt assembly components (Figure below) should be
replaced if inspection reveals distortion, damaged threads, severe corrosion, or
galling. Thoroughly clean draw bars, removing any built-up material on the edge
that engages the hook strip on the screen panel. Replace any draw bar that ca nnot be
restored to fully serviceable condition.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 47 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
Figure 9.2: Rapid change draw bolt assembly components.
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 48 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
*Torque will vary depending on condition of channel protectors and cross and
side products.
Figure 9.3: Rapid change draw bolt assembly installation
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 49 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
9.3.1 Ordinary faults and handling methods of high frequency vibration undersize screen
Table 9.3: The ordinary faults and handling methods of high frequency undersize screen
FAULT FAULT CAUSE HANDLING METHOD
The machine does not vibrate after it is
powered on
The fuse is broken The fuse shall be changed The conducting wire of the coil is short-circuited or the joint of the outgoing line is
broken
The short circuit shall be handle or the outgoing line
shall be connected-well
The vibration is weak, the amplitude is small
after adjusting the potentiometer; it is out
of function or the current is higher
The silicon controlled suffers a breakdown
The silicon controlled shall be changed
The air gap is blocked and the plate spring is blocked
The blocking stuff shall be changed
The machine noise is large, the amplitude is
irregular after adjusting the potentiometer and
there is a violent impact sound.
The plate spring is broken The new plate spring shall be changed
The welding at the joints of the vibrator and the screen is broken or the bolt is broken
and loosed
The welding shall be done and the bolt shall be
changed
The screen frame contacts the slot body
The screen frame shall be suspended in place
The iron core impacts with armature iron
The air gap shall be adjusted to the standard
value of 2mm
9.4 Lubrication
9.5 Dismantling and assembly
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 50 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
10 SPARE PARTS
10.1 Recommended stock of spares
10.2 Storage of spares
10.3 Spares ordering procedure
10.4 Spare parts drawings
10.5 Parts list
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 51 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
10. SPARE PARTS
10.1 Recommended stock of spares
10.1.1 Wearing Part List
Number Name Model Number 1 Vibrating Cap (Quick
Installation) L=60mm
2 Working Mesh Comment: Working Mesh is consumable
The No 1 of Wearing Part - Vibrating Cap including: The method of replacement:
Take out the damaged cap after remove the bolts if the vibrating caps are worn out,
align the cap with the vibrating arm as the drawing, knock by wooden mallet lightly
till in place.
Figure 9.4
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 52 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
10.2 Storage of spares
10.3 Spares ordering procedure
10.4 Spare parts drawings
10.5 Parts list
10.5.1 General spare parts
Table 10.1: The general spare parts of MVS Multi Stack Composite Vibrating Screen are as
follows:
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 53 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
11. REFERENCES
1. Multi-Stack Composite-vibrating Screen D5FMVsk1014d (pdf).
2. Beijing Tieforce Engineering Co., Ltd’s Technical Description of
Beneficiation Process
3. Derrick Stack Sizer SG Motor Maintenance and Operation Manual, Rev 15
Jan 12 (pdf).
4. Cedarapids Operation and Maintenance Manual Flat Screen (pdf).
5. Safety Instruction for Major Equipment Operating (pdf).
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 54 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
12. APPENDICES
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 55 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012
PSSB-IOBP OPERATION & MAINTENANCE MANUAL
Page No. 56 of 57
Revision 0
VIBRATING SCREEN Date 1-May-2012