iqecovav/.., iqeco39 controller installation instructions - mounting · 2015. 6. 15. ·...

IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014 1LT-IQECO-II-07 Rev A

Installation Instructions - Mounting

IQecoVAV/.., IQeco39BACnet MS/TP Terminal Unit Controller

Important: Retain these instructions

These instructions shall be used by trained service personnel onlyIf the equipment is used in a manner not specified by these instructions, the protection provided by the equipment may be impaired.

1 Dimensions ins (mm)

It is recommended that the installation should comply with the local electrical safety installation practices (e.g. HSE Memorandum of Guidance on Electricity at Work Regulations 1989, USA National Electric Code).

6-29/64 (164)

5-3

/64

(1

28

)

5-7

/16

(1

38

)

2-1/4 (58)

6-1

7/6

4 (

15

9)

7/1

6 (

11

)

8-5/16 (211)

10-5/16 (262)

6-27/32 (174)

3 InSTAllATIon - MoUnTIng

2 SToRIng

ConTenTS1 Unpacking ..................................................................... 12 Storing ........................................................................... 1

3 Installation - Mounting ...................................................1

1 UnPACkIng

IQecoVAV/.., IQeco39 Installation Instructions - Mounting (TG201088)

IQecoVAV/.../PA/ only

!MS/TP networkThis product should be connected to a BACnet MS/TP network. The network installation requirements are different from an IQL on its LONWORKS ® network.

H O2

5 %RH 95 %RH+50 °C

(+122 °F)0 °C

(+32 °F)

+60 °C(+140 °F)

-40 °C(-40 °F)

IQecoVAV/..

IQeco39

IQecoVAV/.., IQeco39 Installation Instructions - Mounting

2 IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014 LT-IQECO-II-07 Rev A

2 Requirements

3a Change Actuator Position and/or Direction of Rotation If required, IQecoVAV/.../PA/only. Otherwise go to step 4

3.1 Installation - Mounting (continued)

DIN rail end stop

H O2

5 %RH 95 %RH

Go to step 3b

12

The unit must installed in an enclosure or outside normal reach (e.g. within a plenum).

The unit is UL rated as ‘UL916 listed open energy management equipment’.

+50 °C(+122 °F)

0 °C(+32 °F)

+60 °C(+140 °F)

-40 °C(-40 °F)

IQecoVAV/..

IQeco39

Change Actuator Direction of Rotation ?

YeS no go to step 3b

Suitable for DIN rail or surface mounting

Installation Instructions - Mounting IQecoVAV/.., IQeco39

IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014 3 LT-IQECO-II-07 Rev A

3b Change Actuator Position and/or Direction of Rotation (Change Actuator Position)

3c Change Actuator Position and/or Direction of Rotation (Refi t Actuator Cover)


Ensure cable is located in cut-out

1

2

Ensure cable is not pinched

1

2

Change Actuator Position ?

YeS no, go to step 3c

Go to step 3c

Ensure cable is not pinched


4 IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014 LT-IQECO-II-07 Rev A

6 Mount on Damper Shaft (IQecoVAV/.../PA only)

7 Set Damper limits (IQecoVAV/.../PA only)

5 Attach large Barcode label To Panel

4 Mounting

8 mm spanner,torque setting:

70.8 to 88.5 lb.in (8 to 10 Nm)

Horizontal

45º

Note: If the damper stops are changed it may be necessary to change the VAV Damper driver full scale drive time. See IQecoVAV/.., IQeco39 Installation - Confi guring (TG201121)

U clampDamper shaft (round or square)3/8” to 1/2” (10 mm to 13 mm) diameterMinimum shaft length 1-9/16” (39.68 mm)

1

2

39

ecoPOWER:MAX LOAD: 97 VACLASS 2 CIRCUITS ONLYUSE COPPER CONDUCTORS ONLYFOR INDOOR USE ONLYSUITABLE FOR PELNUM MOUNTING

LAN

Serial No

Strategy

Serial No O/S

LAN

O/S

either surface mount

5 - 3/63”(128 mm)

6 - 29/64” (164 mm)

or DIN rail mount

4 holes Ø 3/16”(4.6 mm)

LAN

Serial No

Strategy

Serial No O/S

LAN

O/S LAN

Serial No

Strategy

Serial No O/S

LAN

O/S

I QECO: Q3 B_ X7 3 0 8 0 0 3 1SERIAL No. IQECO Q3B_X73080031

TREND IQecoLANNIDStrategy : : : : :

O/S

Serial No230 Vac ~24V 10V COM21 22 23 24 25 26 27 281 2 3 24 Vac 0V 10VAO COM1 2 3 54 6 74 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 LON29 30 31 32LONOKSRVPINC

2 3LANNIDStrategy : : : : :

O/S

Serial No230 Vac ~24V 10V COM21 22 23 24 25 26 27 281 2 3 24 Vac 0V 10VAO COM1 2 3 54 6 74 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 LON29 30 31 32LONOKSRVPINC

1 4


8 mm spanner,torque setting: 70.8 to 88.5 lb.in (8 to 10 Nm)



8 Connect Differential Pressure Sensor In8 9 Connect Power link to Terminal 3(If using OUT1 to OUT4)

10 Connect Power

11 Connect Triac outputs (OUT1, OUT2, OUT5*, OUT6* - *IQeco/39, IQecoVAV/P only)

(IQecoVAV/.../PA/ or /P only)

39


4.75 mm (3/16”) ID

IQeco/VAV/../P..

LowHigh

49 VA maximum power to terminal 3

39


IQeco

Power LinkIN8

Duct

Ensure snug fit.Observe polarity

Ensure correct polarity

O

I

Do noT SWITCH on PoWeR

24Vac

24V

2 1

Panel/enclosure ground.Must connect to known earth/ground

UL Listed, Class 2, 24 Vac transformer

For UL rating the input power connections must be made using 18 AWG or larger wire rated at least 90 °C (194 °F).

This equipment must be earthed (grounded), using its power supply connector (terminal 2).

24 Vac ±15%, 50/60 Hz25 VA minimum (including power to actuator but with

terminal 3 disconnected)97 VA maximum (48 VA to terminal 1 + 49 VA to terminal 3)

A panel/enclosure clean earth (ground) consisting of a short (


6 IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014LT-IQECO-II-07 Rev A

12 Connect to MS/TP Trunk

39


The network installation requirements are different from an IQL on its LONWORKS® network.


IQ4NC

12

0 o

hm

s(n

orm

ally

)

Ground screen

Cut backscreen

scre

en

120 ohms (normally)

+82 83

0V V+

120 ohms

Ensure correctpolarity

230 Vac

MS / TP

+34 33

IQeco/VAV/.. /39

24V

2 1


24Vac

MS / TP

+33 34

IQeco/31, /35 /38


24Vac

+

1 2 3

0V

1 2 3

N L

24 Vac

230 Vac

Either or

ad

ditio

na

lte

rmin

al

ad

ditio

na

lte

rmin

al

Lay cable as bus topology (not loop or star).

Ensure correct polarity. Ensure maximum number of devices described below is not exceeded.

earthing: Connect all ground terminals and 24 Vac power supply neutrals to the panel/enclosure ground. Ensure normal safety earthing (grounding) practice.

Cable specification/Maximum length: Use tinned copper, screened, twisted-pair cable with characteristic impedance between 100 and 130 ohms. Distributed capacitance between conductors shall be less than 100 pF per metre (30 pF per foot). Distributed capacitance between conductors and screen shall be less that 200 pF per metre (60 pF per foot). Foil or braided screens are acceptable. The maximum recommended length of an MS/TP segment is 1200 metres (4000 feet) with AWG 18 (0.82 mm2) conductor area) cable. There may be up to 3 repeaters between devices. The use of greater distances and/or different wire gauges shall comply with the electrical specifications of EIA-485. Details of recommended cable are given in the Trend TP Cable Data Sheet (TA200541).

*Screen Each MS/TP segment must have a single point screen ground. Screen should be continuous. Do not ground the MS/TP screen using a controller terminal. Ground screen at one end and cut back at the other end. At connecting points, tie the screen through a terminal.

Additional Terminal

**Terminators: The bus must be terminated at each end with a resistor matched to the cable characteristic impedance (i.e. ±1%, ¼ Watt, range 100 to 130 ohms). If the IQ4NC is at one end of a 120 ohm cable, switch in its built-in terminator, otherwise switch it out and fit a resistor at that end of the cable; the other end must be terminated with a matching resistor.

Maximum number of devices: There may be IQ4NC with up to 64 IQeco’s or other manufacturers’ devices on the MS/TP trunk. A separate limitation is that the MS/TP segment supports up to 32 ‘unit’ loads. IQeco, IQ4NC and IQ3/BINC present a ¼ BACnet ‘unit’ load; other manufacturers’ devices may have different ‘unit’ loads.

Biassing The IQ4NC provides network biassing (470 ohms); a maximum of two devices on the network can provide network biassing.

Failure to comply with these practices will result in significant impairment of the communication performance.



15 Connect Analogue outputs (OUT7, OUT8, OUT9*, OUT10* - *IQeco/39 only)

14 Connect to RD-WMB Room Display(if required)

13 Connect Inputs (IN1 to IN5, IN6*, IN7* - *IQeco/39 only)

Ensure correct polarity

18 AWG (0.8 mm2) 2 wire twisted screened cable should be used for wiring the inputs, with the screen connected to the panel/enclosure ground as shown for IN6 in the adjacent diagram. The far end of the screen should be unterminated.IQeco

IQeco39 only

Sensor

CCCC

2123 2225 24262728293032 31

1

24V III7 23456

39


VV V

I I

I I

Voltage

0 to 10 V

Resistance -- Digital --

Thermistor 10 kohmPotentiometer 1 to 11 kohm

Fan Speed (TBTS/KEF)

IN1 to IN7(IN6, IN7 IQeco/39 only)

wetting current 300 μA

Current 4 to 20 mA IN2 to IN5 only (IN5 IQeco39 only)

External powered

Loop powered

The sensor type module used for the input channel (as set up in the strategy) sets up the input conditioning (no linking required).

INn

C (0 V)

external power supply

Panel/enclosure ground.



auxiliary power output

0 to 10 V at 10 mA maximum (load >1 kohm)

39


IQeco

Load

IQeco39 only

13151618 14

C

17

C

78910

18 AWG (0.8 mm2) 2 wire twisted screened cable should be used with the screen connected to the panel/enclosure ground. Connect the return to the central C terminal (e.g. 14 C, as shown for OUT7) not to an input common.


39


WMB

1920

RD-WMB

RD-WMB

2 part connector with 2 screw terminals for 20 to 14 AWG (0.5 to 2.5 mm2) cross section area cable

Use twisted pair, maximum length 60 m (200 ft)polarity independent



8 IQecoVAV/.., IQeco39 Installation Instructions- Mounting TG201088 Issue 4, 14-Jul-2014LT-IQECO-II-07 Rev A

Please send any comments about this or any other Trend technical publication to [email protected]

© 2014 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited.

Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.

Trend Control Systems limitedAlbery House, Springfield Road, Horsham, West Sussex, RH12 2PQ, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trendcontrols.comTrend Control Systems USA6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel:(425) 869-3900 Fax:(425) 869-8445 www.trend-americas.com

Printed in USA

16 Connect Relay outputs (OUT3, OUT4)

17 Connect Auxiliary Power Output (if required)

18 Configure IQeco

Weee Directive:At the end of their useful life the packaging and product should be disposed of by a suitable recycling centre.Do not dispose of with normal household waste.Do not burn.

Use 18 AWG (0.8 mm2) twisted pair cable

L T - I Q E C O - I I - 0 7

4 DISPoSAl

polarity independent

Normally open, 24 Vac, 0.5A.

39


0 V

IQeco

378C

9

24V4 3

24 Vac

0V

OUTn

CLoad

Terminal 3 must be supplied with 24 Vac supply for OUT3, OUT4 to be used - see step (9) above..

Arc suppression recommended

Relay Output Arc Suppression Installation Instructions(TG200208)

IQeco Installation Instructions - Configuration (TG201121)

39


Use to power sensors.e.g. loop powered - see step (13) above

This is a QR code readable by dedicated QR barcode readers and smartphones.

Scan this code to access the Trend PNet website where you can download all the latest and legacy product publications. A PNet user name and password are required to access the site.

24 Vdc ± 15% @ 100 mA maximum


iqecovav/.., iqeco39 controller installation instructions - mounting · 2015. 6. 15. ·...

Documents