isc capstone network design proposal
TRANSCRIPT
ITT TECHNICAL INSTITUTE
NETWORK DESIGN PROPOSAL
PREPARED FOR ISC CAPSTONE
Student Name
XVI ·· MARCH ·· MMXIV
Abstract: This document is part of the ITT Technical Institute Information Systems and Cybersecurity Bachelorette Degree Capstone project for the graduating class of March 2014. It is part of a collaboration of many different elements which make up the overall ISC Capstone class project.
1
Table of Contents
I. INTRODUCTION 2
II. DESIGN CONSIDERATIONS 2
WAN Services 2
LAN Services 2
Network Fundamentals 2
Security Services 3
III. NETWORK DIAGRAMS AND TOPOLOGIES 4
WAN Topology 4
IV. SYSTEM COMPONENTS 4
V. CONFIGURATIONS 5
2
I. INTRODUCTION
The implementation of a Service Ready Medium Branch Network enables
enterprises with branch offices of 50 to 100 users to deploy high-value network
services such as unified communication and application optimization on top of a
secure branch network infrastructure that is connected to a campus or data center
core (central site) over a variety of WAN technologies. The goal of the Services
Ready Medium Branch Network is to make deployment of these services fast,
simple, and predictable.
The design, test and deployment of this Services Ready Medium Branch Network
will focus on the key elements to ensure the consistent connectivity and mandatory
security requirements for data, voice, and application optimization services.
II. DESIGN CONSIDERATIONS
WAN Services
Layer 3 Multiprotocol Label Switching (MPLS) Virtual Private Network (VPN)
for increased flexibility and reduced bandwidth cost
Dedicated bandwidth ranging from 6 to 44 Mb/s to handle data, voice, and
video traffic
LAN Services
Hierarchical network design to simplify deployment, troubleshooting, and
management
Connectivity to branch devices at Fast Ethernet or Gigabit Ethernet speeds
Near-wire-speed performance between all devices
Provisions for accommodating future expansion
Networking device redundancy without traffic loops
Power-over-Ethernet (PoE)
Network Fundamentals
High availability, rapid recovery, and disaster recovery
Rapid recovery in case of component failure
Automatic switchover to backup WAN link that has a minimum one-quarter of
the bandwidth of the primary WAN link
Ability to restore service within 24 hours in the event of a disaster
Quality of service (QoS)
3
Application-specific traffic prioritization both within the branch office and
across the enterprise
Bandwidth management for WAN-based traffic
Provisions for IP telephony, business video, critical and bulk data applications
Provisions to mitigate denial of service (DoS) and worm attacks
Identification and classification of critical application flows for QoS
IP routing and addressing
Routing within the enterprise and between the branch and the service
provider network
Direct Internet access from the branch
Support for multicast applications
Translation of private addresses and ports in order to access the Internet
Dynamic allocation of IP addresses for end devices
Security Services
Infrastructure protection
Physical securing of access to networking devices
Disabling of unused services that may be used to exploit the network
Authentication of routing protocol updates
Access control
Authentication and authorization services for controlling access to network
resources
Logging capabilities for auditing access to network devices and resources
Integration with global access management system to enforce access
privileges
Secure connectivity
Secure interoffice connectivity for full-mesh and hub-and-spoke WAN
topologies
Secure access into the branch network for remote or home office workers
Voice, video, and data separation on the LAN
Separation of network management traffic
Access to the server in the branch by home office users
Threat protection, detection, and mitigation
Blocking of unauthorized traffic from entering or leaving the branch
Access to servers in the branch by home office users
Verification of source addresses for incoming traffic
Identification and mitigation of common DoS attacks and worms
Prevention of malicious attacks on the branch office network from outside
Prevention of attacks and security breaches from within the branch office
4
III. NETWORK DIAGRAMS AND TOPOLOGIES
WAN Topology
IV. SYSTEM COMPONENTS
Device Platform Modules
P1 Cisco 2851 IS Router 4 - WIC 1DSU-T1 V2 WAN Interface Card
P2 Cisco 2851 IS Router 4 - WIC 1DSU-T1 V2 WAN Interface Card
PE1 Cisco 2811 IS Router 3 - WIC 1DSU-T1 V2 WAN Interface Card
PE2 Cisco 2811 IS Router 3 - WIC 1DSU-T1 V2 WAN Interface Card
PE3 Cisco 2811 IS Router 3 - WIC 1DSU-T1 V2 WAN Interface Card
PE4 Cisco 2811 IS Router 3 - WIC 1DSU-T1 V2 WAN Interface Card
VRF1 CE1 Cisco 2610XM Router 2 - WIC 1DSU-T1 V2 WAN Interface Card Cisco NM-1FE-TX 10/100 Fast Ethernet
VRF1 CE2 Cisco 2610XM Router 2 - WIC 1DSU-T1 V2 WAN Interface Card Cisco NM-1FE-TX 10/100 Fast Ethernet
5
HQ GW Cisco 2610XM Router Cisco NM-1FE-TX 10/100 Fast Ethernet
BR GW Cisco 2610XM Router Cisco NM-1FE-TX 10/100 Fast Ethernet
HQ CORE SW
Catalyst 3550-24 EMI N/A
BR CORE SW
Catalyst 3550-24 EMI N/A
HQ ACCESS SW
Catalyst 3524-24 EMI N/A
BR ACCESS SW
Catalyst 3524-24 EMI N/A
V. CONFIGURATIONS
hostname P1 ! mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.0.1 255.255.255.255 ! interface GigabitEthernet0/0 description Connected to P2 Fa0/0 ip address 10.1.0.1 255.255.255.252 ip ospf network point-to-point duplex auto speed auto mpls traffic-eng tunnels ! interface GigabitEthernet0/1 description Connected to P2 Fa2/0 ip address 10.1.0.5 255.255.255.252 ip ospf network point-to-point duplex auto speed auto mpls traffic-eng tunnels ! interface Serial0/0/0 description Connected to PE1 S1/0 ip address 10.1.1.1 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels no fair-queue service-module t1 timeslots 1-24 ! interface Serial0/1/0
6
description Connected to PE2 S1/0 ip address 10.1.1.5 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to PE3 S1/0 ip address 10.1.1.9 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to PE4 S1/0 ip address 10.1.1.13 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.0.1 network 10.0.0.1 0.0.0.0 area 0 network 10.1.0.0 0.0.0.7 area 0 network 10.1.1.0 0.0.0.15 area 0 ! router bgp 65000 bgp router-id 10.0.0.1 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor 10.0.0.2 remote-as 65000 neighbor 10.0.0.2 update-source Loopback0 neighbor 10.0.0.2 send-community extended neighbor 10.0.1.1 peer-group MPLS neighbor 10.0.1.2 peer-group MPLS neighbor 10.0.1.3 peer-group MPLS neighbor 10.0.1.4 peer-group MPLS ! address-family vpnv4 neighbor MPLS send-community extended neighbor MPLS route-reflector-client
7
neighbor 10.0.1.1 activate neighbor 10.0.1.2 activate neighbor 10.0.1.3 activate neighbor 10.0.1.4 activate exit-address-family
hostname P2 ! mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.0.2 255.255.255.255 ! interface GigabitEthernet0/0 description Connected to P1 Fa0/0 ip address 10.1.0.2 255.255.255.252 ip ospf network point-to-point duplex auto speed auto mpls traffic-eng tunnels ! interface GigabitEthernet0/1 description Connected to P1 Fa2/0 ip address 10.1.0.6 255.255.255.252 ip ospf network point-to-point duplex auto speed auto mpls traffic-eng tunnels ! interface Serial0/0/0 description Connected to PE1 S1/1 ip address 10.1.2.1 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels no fair-queue service-module t1 timeslots 1-24 ! interface Serial0/1/0 description Connected to PE2 S1/1 ip address 10.1.2.5 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to PE3 S1/1 ip address 10.1.2.9 255.255.255.252
8
ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to PE4 S1/1 ip address 10.1.2.13 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.0.2 network 10.0.0.2 0.0.0.0 area 0 network 10.1.0.0 0.0.0.7 area 0 network 10.1.2.0 0.0.0.15 area 0 ! router bgp 65000 bgp router-id 10.0.0.2 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor 10.0.0.1 remote-as 65000 neighbor 10.0.0.1 update-source Loopback0 neighbor 10.0.0.1 send-community extended neighbor 10.0.1.1 peer-group MPLS neighbor 10.0.1.2 peer-group MPLS neighbor 10.0.1.3 peer-group MPLS neighbor 10.0.1.4 peer-group MPLS ! address-family vpnv4 neighbor MPLS send-community extended neighbor MPLS route-reflector-client neighbor 10.0.1.1 activate neighbor 10.0.1.2 activate neighbor 10.0.1.3 activate neighbor 10.0.1.4 activate exit-address-family
hostname PE1 ip cef no ip dhcp use vrf connected ip dhcp excluded-address 172.16.100.1
9
! ip dhcp pool sdm-pool1 network 172.16.100.0 255.255.255.252 default-router 172.16.100.1 ! ip vrf vrf1 rd 64512:1 route-target export 64512:1 route-target import 64512:1 ! ip vrf vrf2 rd 64512:2 route-target export 64512:2 route-target import 64512:2 ! no ip domain lookup ! multilink bundle-name authenticated mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.1.1 255.255.255.255 ! interface Tunnel2 ip unnumbered Loopback0 tunnel destination 10.0.1.2 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 2 dynamic no routing dynamic ! interface Tunnel3 ip unnumbered Loopback0 tunnel destination 10.0.1.3 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 3 dynamic no routing dynamic ! interface Tunnel4 ip unnumbered Loopback0 tunnel destination 10.0.1.4 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 4 dynamic no routing dynamic
10
! interface FastEthernet0/0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description $ETH-LAN$ ip address 172.16.100.1 255.255.255.252 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface Serial0/0/0 description Connected to P1 S0/0/0 ip address 10.1.1.2 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/1/0 description Connected to P2 S0/0/0 ip address 10.1.2.2 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to VRF1-CE1 S0/1 ip vrf forwarding vrf1 ip address 192.168.1.2 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to VRF2-CE1 S0/0 ip vrf forwarding vrf2 ip address 192.168.1.2 255.255.255.252 ip ospf network point-to-point
11
mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.1.1 log-adjacency-changes network 10.0.1.1 0.0.0.0 area 0 network 10.1.1.2 0.0.0.0 area 0 network 10.1.2.2 0.0.0.0 area 0 ! router bgp 65000 bgp router-id 10.0.1.1 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor 10.0.0.1 peer-group MPLS neighbor 10.0.0.2 peer-group MPLS ! address-family ipv4 neighbor MPLS send-community extended no neighbor 10.0.0.1 activate no neighbor 10.0.0.2 activate no auto-summary no synchronization exit-address-family ! address-family vpnv4 neighbor MPLS send-community extended neighbor 10.0.0.1 activate neighbor 10.0.0.2 activate exit-address-family ! address-family ipv4 vrf vrf2 neighbor 192.168.1.1 remote-as 64512 neighbor 192.168.1.1 activate neighbor 192.168.1.1 as-override maximum-paths 2 no synchronization exit-address-family ! address-family ipv4 vrf vrf1
12
neighbor 192.168.1.1 remote-as 64512 neighbor 192.168.1.1 activate neighbor 192.168.1.1 as-override maximum-paths 2 no synchronization exit-address-family ! ip nat inside source list 1 interface FastEthernet0/0 overload ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.100.0 0.0.0.3
hostname PE2 ip cef ip vrf vrf1 rd 64512:1 route-target export 64512:1 route-target import 64512:1 ! ip vrf vrf2 rd 64512:2 route-target export 64512:2 route-target import 64512:2 ! mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.1.2 255.255.255.255 ! interface Tunnel1 ip unnumbered Loopback0 tunnel destination 10.0.1.1 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 1 dynamic no routing dynamic ! interface Tunnel3 ip unnumbered Loopback0 tunnel destination 10.0.1.3 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 3 dynamic no routing dynamic ! interface Tunnel4 ip unnumbered Loopback0
13
tunnel destination 10.0.1.4 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 4 dynamic no routing dynamic ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 description Connected to P1 S1/1 ip address 10.1.1.6 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels no fair-queue service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/1/0 description Connected to P2 S1/1 ip address 10.1.2.6 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to VRF1-CE1 S1/1 ip vrf forwarding vrf1 ip address 192.168.1.6 255.255.255.252 service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to VRF2-CE1 S1/1 ip vrf forwarding vrf2 ip address 192.168.1.6 255.255.255.252
14
service-module t1 clock source internal service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.1.2 log-adjacency-changes network 10.0.1.2 0.0.0.0 area 0 network 10.1.1.6 0.0.0.0 area 0 network 10.1.2.6 0.0.0.0 area 0 ! router bgp 65000 no synchronization bgp router-id 10.0.1.2 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor MPLS send-community extended neighbor 10.0.0.1 peer-group MPLS no neighbor 10.0.0.1 activate neighbor 10.0.0.2 peer-group MPLS no neighbor 10.0.0.2 activate no auto-summary ! address-family vpnv4 neighbor MPLS send-community extended neighbor 10.0.0.1 activate neighbor 10.0.0.2 activate exit-address-family ! address-family ipv4 vrf vrf2 neighbor 192.168.1.5 remote-as 64512 neighbor 192.168.1.5 activate neighbor 192.168.1.5 as-override maximum-paths 2 no synchronization exit-address-family ! address-family ipv4 vrf vrf1 neighbor 192.168.1.5 remote-as 64512 neighbor 192.168.1.5 activate neighbor 192.168.1.5 as-override maximum-paths 2
15
no synchronization exit-address-family
hostname PE3 ! ip cef ip vrf vrf1 rd 64512:1 route-target export 64512:1 route-target import 64512:1 ! ip vrf vrf2 rd 64512:2 route-target export 64512:2 route-target import 64512:2 ! no ip dhcp use vrf connected ip dhcp excluded-address 172.16.200.1 ! ip dhcp pool sdm-pool1 network 172.16.200.0 255.255.255.252 default-router 172.16.200.1 ! mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.1.3 255.255.255.255 ! interface Tunnel1 ip unnumbered Loopback0 tunnel destination 10.0.1.1 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 1 dynamic no routing dynamic ! interface Tunnel2 ip unnumbered Loopback0 tunnel destination 10.0.1.2 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 2 dynamic no routing dynamic ! interface Tunnel4 ip unnumbered Loopback0 tunnel destination 10.0.1.4
16
tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 4 dynamic no routing dynamic ! interface FastEthernet0/0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description $ETH-LAN$ ip address 172.16.200.1 255.255.255.252 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface Serial0/0/0 description Connected to P1 S1/2 ip address 10.1.1.10 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels no fair-queue service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/1/0 description Connected to P2 S1/2 ip address 10.1.2.10 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to VRF1-CE2 S1/0 ip vrf forwarding vrf1 ip address 192.168.1.10 255.255.255.252 service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to VRF2-CE2 S1/0
17
ip vrf forwarding vrf2 ip address 192.168.1.10 255.255.255.252 service-module t1 clock source internal service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.1.3 log-adjacency-changes network 10.0.1.3 0.0.0.0 area 0 network 10.1.1.10 0.0.0.0 area 0 network 10.1.2.10 0.0.0.0 area 0 ! router bgp 65000 bgp router-id 10.0.1.3 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor 10.0.0.1 peer-group MPLS neighbor 10.0.0.2 peer-group MPLS ! address-family ipv4 neighbor MPLS send-community extended no neighbor 10.0.0.1 activate no neighbor 10.0.0.2 activate no auto-summary no synchronization exit-address-family ! address-family vpnv4 neighbor MPLS send-community extended neighbor 10.0.0.1 activate neighbor 10.0.0.2 activate exit-address-family ! address-family ipv4 vrf vrf2 neighbor 192.168.1.9 remote-as 64512 neighbor 192.168.1.9 activate neighbor 192.168.1.9 as-override maximum-paths 2 no synchronization exit-address-family !
18
address-family ipv4 vrf vrf1 neighbor 192.168.1.9 remote-as 64512 neighbor 192.168.1.9 activate neighbor 192.168.1.9 as-override maximum-paths 2 no synchronization exit-address-family ! ip nat inside source list 1 interface FastEthernet0/0 overload ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.200.0 0.0.0.3
hostname PE4 ! ip cef ip vrf vrf1 rd 64512:1 route-target export 64512:1 route-target import 64512:1 ! ip vrf vrf2 rd 64512:2 route-target export 64512:2 route-target import 64512:2 ! mpls traffic-eng tunnels ! interface Loopback0 ip address 10.0.1.4 255.255.255.255 ! interface Tunnel1 ip unnumbered Loopback0 tunnel destination 10.0.1.1 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 1 dynamic no routing dynamic ! interface Tunnel2 ip unnumbered Loopback0 tunnel destination 10.0.1.2 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 2 dynamic no routing dynamic !
19
interface Tunnel3 ip unnumbered Loopback0 tunnel destination 10.0.1.3 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng path-option 3 dynamic no routing dynamic ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 description Connected to P1 S1/3 ip address 10.1.1.14 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/1/0 description Connected to P2 S1/3 ip address 10.1.2.14 255.255.255.252 ip ospf network point-to-point mpls traffic-eng tunnels service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/2/0 description Connected to VRF1-CE2 S1/1 ip vrf forwarding vrf1 ip address 192.168.1.14 255.255.255.252 service-module t1 clock source internal service-module t1 timeslots 1-24 ! interface Serial0/3/0 description Connected to VRF2-CE2 S1/1 ip vrf forwarding vrf2
20
ip address 192.168.1.14 255.255.255.252 service-module t1 clock source internal service-module t1 timeslots 1-24 ! router ospf 65000 mpls traffic-eng router-id Loopback0 mpls traffic-eng area 0 router-id 10.0.1.4 log-adjacency-changes network 10.0.1.4 0.0.0.0 area 0 network 10.1.1.14 0.0.0.0 area 0 network 10.1.2.14 0.0.0.0 area 0 ! router bgp 65000 bgp router-id 10.0.1.4 bgp log-neighbor-changes timers bgp 12 36 neighbor MPLS peer-group neighbor MPLS remote-as 65000 neighbor MPLS update-source Loopback0 neighbor 10.0.0.1 peer-group MPLS neighbor 10.0.0.2 peer-group MPLS ! address-family ipv4 neighbor MPLS send-community extended no neighbor 10.0.0.1 activate no neighbor 10.0.0.2 activate no auto-summary no synchronization exit-address-family ! address-family vpnv4 neighbor MPLS send-community extended neighbor 10.0.0.1 activate neighbor 10.0.0.2 activate exit-address-family ! address-family ipv4 vrf vrf2 neighbor 192.168.1.13 remote-as 64512 neighbor 192.168.1.13 activate neighbor 192.168.1.13 as-override maximum-paths 2 no synchronization exit-address-family ! address-family ipv4 vrf vrf1
21
neighbor 192.168.1.13 remote-as 64512 neighbor 192.168.1.13 activate neighbor 192.168.1.13 as-override maximum-paths 2 no synchronization exit-address-family
hostname VRF1-CE1 ! ip cef ! no ip dhcp use vrf connected ip dhcp excluded-address 10.10.100.1 10.10.100.100 ip dhcp excluded-address 10.10.100.200 10.10.100.254 ! ip dhcp pool sdm-pool1 import all network 10.10.100.0 255.255.255.0 default-router 10.10.100.1 dns-server 10.10.100.21 4.2.2.2 domain-name CAPSTONE.LOCAL ! no ip domain lookup ip name-server 10.10.100.1 ip name-server 4.2.2.2 ip auth-proxy max-nodata-conns 3 ip admission max-nodata-conns 3 ! interface Loopback0 ip address 10.255.0.1 255.255.255.255 ! interface FastEthernet0/0 ip address 10.10.100.1 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface Serial0/0 description Connected to PE1 S1/2 ip address 192.168.1.1 255.255.255.252 no fair-queue service-module t1 timeslots 1-24 ! interface Serial0/1 description Connected to PE2 S1/2 ip address 192.168.1.5 255.255.255.252
22
service-module t1 timeslots 1-24 ! interface FastEthernet1/0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! router bgp 64512 no synchronization bgp log-neighbor-changes timers bgp 12 36 redistribute connected neighbor 192.168.1.2 remote-as 65000 neighbor 192.168.1.6 remote-as 65000 no auto-summary ! ip forward-protocol nd ! ip nat inside source list 1 interface FastEthernet1/0 overload ! access-list 1 permit 10.10.100.0 0.0.0.255
hostname VRF1-CE2 ip cef ! no ip dhcp use vrf connected ip dhcp excluded-address 10.10.200.1 10.10.200.100 ip dhcp excluded-address 10.10.200.200 10.10.200.254 ! ip dhcp pool sdm-pool2 import all network 10.10.200.0 255.255.255.0 domain-name CAPSTONE.LOCAL dns-server 10.10.200.21 4.2.2.2 default-router 10.10.200.1 ! no ip domain lookup ip name-server 10.10.200.2 ip name-server 4.2.2.2 ip auth-proxy max-nodata-conns 3 ip admission max-nodata-conns 3 ! interface Loopback0 ip address 10.255.0.2 255.255.255.255 !
23
interface FastEthernet0/0 ip address 10.10.200.1 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface Serial0/0 description Connected to PE3 S1/2 ip address 192.168.1.9 255.255.255.252 no fair-queue service-module t1 timeslots 1-24 ! interface Serial0/1 description Connected to PE4 S1/2 ip address 192.168.1.13 255.255.255.252 service-module t1 timeslots 1-24 ! interface FastEthernet1/0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! router bgp 64512 no synchronization bgp log-neighbor-changes timers bgp 12 36 redistribute connected neighbor 192.168.1.10 remote-as 65000 neighbor 192.168.1.14 remote-as 65000 no auto-summary ! ip forward-protocol nd ! ip nat inside source list 1 interface FastEthernet1/0 overload ! access-list 1 permit 10.10.200.0 0.0.0.255