Description Nu-MC2TM is the most eco-friendly floor finish available This first-ever Bio-Powered™ emulsion combines durability and shine in a product that is easy to apply and maintain. Its exceptional spreadability makes it a very easy to apply. Plus its long-lasting shine makes maintainance easy and reduces the need to strip it as often. Nu-MC2TM is a low-odour product that emits very low levels of VOCs.

ApplicationsNu-MC2TM is the floor finish of choice when going green in the healthcare industry, the education sector, public buildings or any industry concerned with the environment. It offers a better alternative to sealers and is compatible with composite vinyl, marmoleum, linoleum and natural stone floors. This versatile product responds well to low-speed, high-speed and ultra-high-speed buffing. FOR PROFESSIONAL USE.

READY TO USEHYBRID FLOOR FINISH WITH BIO-ELASTOMERS 10TM

FLO

OR

CA

RE

ISEU-400-00

DirectionsApply Nu-MC2TM floor finish to the surface as needed. Make sure that the finish dries completely between each application. Does not require sealer preparation. Two to four coats are appropriate for most situations. Works with all application tools and methods. This versatile product responds well to low-speed (350 rpm), high-speed (1,500+ rpm) and ultra-high-speed (propane powered) buffing.Application method: Apply after the appropriate stripping or scrubbing procedure. Be sure to rinse floor thoroughly before applying. Apply Nu-MC2TM section by section: first, using the applicator, mark off the perimetre of the section. Apply using a back-and-forth, semicircular motion, ensuring complete, even coverage throughout the section. Repeat in the other sections. Let dry (under normal humidity conditions, 20-30 minutes). When the surface is no longer tacky to the touch, begin the next coat.

Once you have finished all coats, rinse all equipment that was in contact with Nu-MC2TM thoroughly in running water. Put tools away properly so they will dry quickly.Daily cleaning method: Remove dust and litter with a dust mop. Wash the surface with a cleaner such as Nu-Kleen AllTM or a neutral degreaser such as Nu-Action 3TM.Burnishing (high-speed or ultra-high-speed dry buffing): Clean the surface tho-Clean the surface tho-roughly using the daily cleaning method. Let dry completely. Polish the surface with a high-speed or ultra-high-speed buffing machine fitted with the appropriate pad.

Replace or flip the pad when it becomes soiled or sticky.Scrubbing and applying a new coat: Apply a solution of Nu-Action 3TM (1:50) to

the floor. Scrub with a buffer fitted with the appropriate pad. Replace or flip the pad when it becomes soiled or sticky. Remove the solution with a wet vac, flat mop or automatic scrubber. Rinse with plenty of clean water. Remove the solution with a wet vac, flat mop or automatic scrubber. Let dry completely before applying a coat of Nu-MC2TM.Polishing with spray buff: Clean the surface thoroughly using the daily cleaning method. Let dry completely.

Gently mist Nu-EgälTM spray buff over the surface, then use a buffer to spread the product and polish at the same time.

Innu-Science RH (UK) LimitedWoodside Lodge, Cobbett’s Hill

Weybridge, Surrey KT13 0UATel.: +44 (0) 7740 100222Fax: +44 (0) 1942 887160

www.innu-science.co.uk

mc2

FLO

OR

CA

RE

Regulatory complianceSlip resistance exceeding ASTM D2047 standards Directive 1999/45/EC and Amendments on Dangerous PreparationsRegulation (EC) No 1907/2006, Annex II on Safety Data SheetsREACH Regulation (EC) No 1907/2006

Respect for the environment Tips for being greener■ Follow suggested procedures ■frequency ■ Make good use of entry mats ■areas ■ ■ Never mix products ■ Train staff on the environmental impact of their work.

Reduced environmental stress ■ Low toxicity ■ Reduced chemical waste ■ Very low-VOC emulsions: helps reduce GHGs ■ Less frequent stripping required (highly durable).Fits perfectly into any organisation's efforts to be more eco-responsible by going green.Polymers with no: zinc, ammonia, recognised cancer- or mutation-causing substances, substances affecting reproductive systems, dibutyl phthalate, 2-methoxyethanol or 2-butoxyethanol.

Packaging codesISEU-400-00-1005 5 litres (Part No 810038)ISEU-400-00-1010 10 litresISEU-400-00-1025 25 litres

READY TO USEHYBRID FLOOR FINISH WITH BIO-ELASTOMERS 10TM

ISEU-400-00

TechnologyNu-MC2TM

biotechnology-based emulsion. It is derived from Innu-Science's unique

TM technology, which uses Bio-Elastomers 10TM (bio-polymers synthesised by microorganisms) to form a high-density polymer network (without heavy metals), creating a

These properties provide outstanding durability, exceptional spreadability and wide versatility in terms of cleaning methods and tools.

Composition Water, zinc-free emulsions, solvent, plasticiser, resin, non-ionic surfactants.Properties■ White liquid, characteristic odour. Do not allow to freeze.

pH1 148

Nu-EnergikäTM

Ecological

Related products

Nu-MC3TM

Concentrated hybrid

Bio-Elastomers 20TM

Cleaning tips oC ■ If you use a fan to reduce

drying time for each coat, wait at least 10 minutes after applying the product before turning it on ■ Always work with clean, well-maintained tools ■ ■ Avoid jerky or sudden movements during application: work smoothly and evenly ■ Avoid corrective strokes during application: Nu-MC2TM levels

out nicely on its own ■ If you must interrupt the application, leave the applicator in the bucket and close the garbage bag to avoid evaporation.

Not regulated by the regulation on transport of dangerous goods.Material safety data sheet available upon request. Read it before using this product.Safety advice: S25- Avoid contact with eyes. S26- In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

Nu-EgälTM

Hybrid spray buff with Bio-Elastomers 15TM

Nu-Action 3TM

Power degreaser

FP_N

u-M

C2_

ISE

U_4

00_0

0_E

N_J

UN

E10

mc2