items list.xlsx

40
17 273.52 34 100.00 39 410.28 S.No. Particular of Items Quantity Unit Providing and Making in POP ceiling , in G.I. Channel supports to level required. Work include suspenders and hangers from roof slab / beams, cutting and fixing of gypboard joint, making grooves, bends cutouts with edge frame for light fixtures, A/C grills, additional hangers, covers etc. and including taping and putty. Nothing extra shall be paid for narrow strips upto min. width 50mm. including cost of all material, labour, T&P Sqm. Providing and applying two coats of external grade acrylic Textured paint of approved make as specified over one coat of primer applied on external plaster on wall, ceiling and beams by scraping the surface as directed, cleaning etc. complete as per the approved colour and shade at any height and level as directed by EIC. The rate should inclusive of MS scaffolding etc. complete. Sqm Providing and fixing at all levels acoustical false ceiling of fine fissured Armstrong make/ equivalent, 12 mm thick butt edge mineral fiber board conforming to IS:2095 including providing and fixing of framework made of special factory made sections power pressed from MS sheet and galvanized in accordance with coating 600 as per IS:277 and consisting of angle cleats of size 24 mm wide x 1.6 mm thick with flanges of 24 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastener 12.5 mm dia x 40 mm long with 6 mm dia bolts to the angle hangers of 25x25x5 mm MS angle or bar of required length and other end of angle hanger being fixed with nut and bolts to GI channels 24 mmx 38 mmx 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80 mm with tapered flange of 26 mm each having clips of 10.5 mm at 400 mm centre to centre shall be fixed in a direction perpendicular to the GI channel/ tee with SQM

Upload: david-ray

Post on 18-Jan-2016

59 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: items list.xlsx

17 273.52

34 100.00

39 410.28

S.No. Particular of Items Quantity Unit RATEProviding and Making in POP ceiling , in G.I. Channel supports to level required. Work include suspenders and hangers from roof slab / beams, cutting and fixing of gypboard joint, making grooves, bends cutouts with edge frame for light fixtures, A/C grills, additional hangers, covers etc. and including taping and putty. Nothing extra shall be paid for narrow strips upto min. width 50mm. including cost of all material, labour, T&P etc. complete.

Sqm.

Providing and applying two coats of external grade acrylic Textured paint of approved make as specified over one coat of primer applied on external plaster on wall, ceiling and beams by scraping the surface as directed, cleaning etc. complete as per the approved colour and shade at any height and level as directed by EIC. The rate should inclusive of MS scaffolding etc. complete.

Sqm

Providing and fixing at all levels acoustical false ceiling of fine fissured Armstrong make/ equivalent, 12 mm thick butt edge mineral fiber board conforming to IS:2095 including providing and fixing of framework made of special factory made sections power pressed from MS sheet and galvanized in accordance with coating 600 as per IS:277 and consisting of angle cleats of size 24 mm wide x 1.6 mm thick with flanges of 24 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastener 12.5 mm dia x 40 mm long with 6 mm dia bolts to the angle hangers of 25x25x5 mm MS angle or bar of required length and other end of angle hanger being fixed with nut and bolts to GI channels 24 mmx 38 mmx 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80 mm with tapered flange of 26 mm each having clips of 10.5 mm at 400 mm centre to centre shall be fixed in a direction perpendicular to the GI channel/ tee with connecting clips made out of 2.64 mm dia x 230 mm long GI wire at every junction including fixing the mineral fiber board with ceiling section and perimeter channels 0.5 mm thk 27 mm high having flange of 20 mm and 30 mm long. The perimeter of the ceiling fixed to wall/ partition with the help of rawl plugs at 400 mm centre to centre with a 25 mm long drive-all screw @ 230mm intervals including jointing and fixing to have flush finish of tapered and square edges of the mineral fiber board with recommended filler, paper taps, finisher and two coats of primer suitable for mineral

SQM

Page 2: items list.xlsx

40 50.00

50.00

50.00

41 40.00

50 20.00

54 20.00

Providing and fixing in position, plaster of paris moulding of required sizes and shade as per design decided as approved with painting to give an even shade at all levels. a) 40mm x 40mm

RM

b) 40mm x 75mm RM

c) 75mm x 150mm RM

Providing and fixing 6mm thick multi-wall polycarbonate sheet suitable for wind pressure 250 Kg/sqm GE / Lexan / Vergola or approved equivalent make of any color and shade in required shape for sky light over the truss / MS section frame work, fixing with aluminium flat of required size over the sheet with all necessary materials, hardware, sealant, rubber gasket, screws, fastners etc. with proper overlap and sealing the joint with appropriate sealant to make water tight including cost of all material, tools and plants, labour etc. complete as per drawing and directed by EIC at all heights excluding the cost of steel structure

SQM

Acoustic paneling with high density acoustical board of NRC 0.50 finished with approved cloth SQM

Providing and fixing sound absorptive wall paneling in profile with 50x50 mm II-class teak wood/ approved section with grid size 600mmx 600mm c/c vertically and horizontally fixing the same with GI chicken wire mesh creating 50mm air gap as approved by as approved and fixing GI hat furring channel 22-25 depth with grid size 600x600mm on wooden frame (Extra fixing of member as per requirement). Fixing the frame gap with 25mm/ 1500 (32 kgs/cum) glass wool of TWIGA approved. The entire wall paneling will be fixed and covered with Black Hessian jute cloth plain weave cloth with single warp and weft interwoven weighing not more than 576 gms/sqm of approved make and to the satisfaction of approved. Providing and fixing 150mm x 15m rubber wood steam beech wood slats over a backing of GI frame structure. steam beech wood slats to be melamine matt polished. The gap between the slats to be 8 mm fixed to the satisfaction of the as approved. Note: rate to include cutting and making provision for housing light fixtures, conduiting and electrical fixture as per the drawing and instructions by the as approved

SQM

Page 3: items list.xlsx

55 963.50

Providing and fixing Luxalon® SL-4 84R Plain Panel Sun Louvers manufactured by M/s. Hunter Douglas India Pvt. Ltd. or equivalent make of approved colour as per architectural drawings consisting of panel 84 mm wide x 16mm deep x 0.6mm thick with round edges panel length upto 6mtrs coil coated on a continuous paint line double baked and roll formed from enameled corrosion Resistance Aluminium Alloy AA3005 (Al.Mg.) for higher strength and good Roll forming characteristics. Panel shall be clipped to baked enameled Aluminium SL-4 panel stringer of 33mm wide and 86mm deep x 0.95 mm thick in a standard length of 5mtrs made of double baked enameled Aluminium Alloy AA5050 (Al.Mg.) black with cut-outs to hold the panel in a module of 86mm centre to centre at a distance of 1mtr. The carrier shall be fixed to a suitable structure by means of rigid fixing details.Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint, enameled twice under high temperature one side with full primer and Luxacote finish, the other side (inner side) with a primer coat and Skin Coat on a Continuous Paint Line.

SQM

Page 4: items list.xlsx

0.00

0.00

0.00

AMOUNT

Page 5: items list.xlsx

0.00

0.000.00

0.00

0.00

0.00

Page 6: items list.xlsx

0.00

Page 7: items list.xlsx

19 497.07

41 40.00

S.No. Particular of Items Quantity Unit RATE

Providing and fixing factory made flush doors 30 mm thick with solid block board core internally lipped with commercial hard wood timber hot pressed bonded with water proof type phenol formaldehyde with the synthetic resin bonded generally confirming to IS:2202-1991 including superior Indian make Brass fittings, cleats, and door stoppers, fixed in position (with both side commercial face with brass fitting) at any floor with supplying and fixing following fittings and as per drawing including all lead and lift etc. complete. List of fittings (in each door shutter): Brass / SS Finish Tower bolts (Barrel type) 250x10mm 2 Nos. Hinges 4 nos. Brass / SS Finish door aldrop 300x16x5mm 2 Nos. Hanging type floor door stopper with twin rubber. Front side teak face with 8mm wide Groove & laminate insert and other side commercial face.

Sqm.

Providing and fixing 6mm thick multi-wall polycarbonate sheet suitable for wind pressure 250 Kg/sqm GE / Lexan / Vergola or approved equivalent make of any color and shade in required shape for sky light over the truss / MS section frame work, fixing with aluminium flat of required size over the sheet with all necessary materials, hardware, sealant, rubber gasket, screws, fastners etc. with proper overlap and sealing the joint with appropriate sealant to make water tight including cost of all material, tools and plants, labour etc. complete as per drawing and directed by EIC at all heights excluding the cost of steel structure

SQM

Page 8: items list.xlsx

47 20.00

48 20.00

49 20.00

50 20.00

51 20.00

Paneling on columns / walls with 12 mm thick commercial plywood (ply backing of appropriate size to make paneling leveled if required as per site condition to the satisfaction and as approved) as per drawings and finished with 1 mm thk. laminate as approved on exposed faces with grooves as per design, with skirting 15 mm x 75 mm in teakwood/ steambeach/ pinewood/ Maplewood as per profile with groove as per design to meet edges and junction with wall or any other junctions. The rates shall include all hardware, fittings, adhesives, beadings, lippings etc. as approved.

SQM

Paneling on columns / walls with 12 mm thk. commercial plywood (ply backing of appropriate size to make paneling) leveled if required as per site condition to the satisfaction of an EIC) and finished with veneer duly polished as approved and as per drawings on exposed faces with grooves as per design, with skirting 15mm x 75 mm in teakwood/ steambeach/ pinewood/ Maplewood as per profile with groove as per design to meet edges and junction with wall or any other junctions. The rates shall include all hardware, fittings, adhesives, beadings, lippings etc. as approved.

SQM

Providing and fixing wall paneling - Modular type must be with 18 mm thick board fixed with aluminium T-type system modular type unexposed. with provision for cabling wherever required. With prelaminated MDF board 18mm thick ISI make.

SQM

Acoustic paneling with high density acoustical board of NRC 0.50 finished with approved cloth SQM

With prelaminated - melamine polish 18mm thick veneer MDF board SQM

Page 9: items list.xlsx

52 20.00

53 20.00

Providing and fixing paneling on wall, on GI hat furring channel 22-25 depth with grid size 600mm x 600mm both ways fixed to wall, columns in any profile and covered with 8mm plywood of approved make for height as shown in the drawings and finished with veneer/ laminate/ canfor panel/ carpet/ fabric of approved figure, make and shade by the EIC (with melamine polish and grooves as per requirements) at the distances shown in drawing or as directed, complete with side edgings and beadings of profiles demarcated in the drawings in teakwood/ steambeach/ pinewood of shown size and finished with melamine polish and with 80mmx35mm wooden skirting in teakwood/ steambeach/ pinewood/ Maplewood carved to profile as approved finished with melamine polish. The rate shall also include all the wooden mouldings, cornices and edge coverings as shown in the drawings or as directed, with melamine polish etc. complete. The wooden cornices would be of first quality teak wood, steam beach wood, as approved. (Note: Quote rate for veneer, for other than veneer the item would be paid as per the rate analysis submitted and approved)

SQM

Providing and fixing soft board panels on walls/ partition / paneling in the area indicated in the drawings. 18mm thk. soft board with backing of 8-12 mm thk ply duly framed with 25x25mm teakwood/ steambeach/ pinewood framing on all four sides. Soft board panel shall be finished with approved fabric Rs. 200/- R.Mt. The soft board shall be fixed with 35mm x 18mm half round teakwood/ steambeach / pinewood beading. All exposed wooden surfaces shall be finished with Melamine polish Rate shall include fixing the whole panel in the space earmarked for the same as per drawing and as approved.

SQM

Page 10: items list.xlsx

54 20.00

Providing and fixing sound absorptive wall paneling in profile with 50x50 mm II-class teak wood/ approved section with grid size 600mmx 600mm c/c vertically and horizontally fixing the same with GI chicken wire mesh creating 50mm air gap as approved by as approved and fixing GI hat furring channel 22-25 depth with grid size 600x600mm on wooden frame (Extra fixing of member as per requirement). Fixing the frame gap with 25mm/ 1500 (32 kgs/cum) glass wool of TWIGA approved. The entire wall paneling will be fixed and covered with Black Hessian jute cloth plain weave cloth with single warp and weft interwoven weighing not more than 576 gms/sqm of approved make and to the satisfaction of approved. Providing and fixing 150mm x 15m rubber wood steam beech wood slats over a backing of GI frame structure. steam beech wood slats to be melamine matt polished. The gap between the slats to be 8 mm fixed to the satisfaction of the as approved. Note: rate to include cutting and making provision for housing light fixtures, conduiting and electrical fixture as per the drawing and instructions by the as approved

SQM

Page 11: items list.xlsx

0.00

0.00

AMOUNT

Page 12: items list.xlsx

0.00

0.00

0.00

0.00

0.00

Page 13: items list.xlsx

0.00

0.00

Page 14: items list.xlsx

0.00

Page 15: items list.xlsx

43 36.40 0.00

44 124.80 0.00

S.No. Particular of Items Quantity Unit RATE AMOUNTProviding, fabricating and fixing 12mm thick clear toughened glass with edge polished and prepared for patch fittings with required designs approved in frosting & Petching dimensions as shown in drawings, for sensor based Automatic entrance door. The entrance glass door shall be fitted with over panel patch fitting, top patch fitting, and bottom rail with locking system, the fixed glazing shall be supported by connecting profiles etc. all the patch fitting, panels, connectors and other accessories should be SS brush finish. All handles, floors springs shall be of ‘Dorma’ or equivalent. All joints shall be sealed with silicon based seal and made water tight etc. complete as per drawing and instructions.

SQM

Providing, fabricating and fixing 12mm thick clear toughened glass with edge polished and prepared for patch fittings with required designs approved in frosting & Petching dimensions as shown in drawings for fixed front glazing. The glazing shall be fitted with over panel patchfitting,, top patch fitting, centre & bottom rail with locking system, the fixed glazing shall be supported by connecting profiles etc. all the patch fitting, panels, connectors and other accessories should be S.S. brush finish. All joints shall be sealed with silicon based seal and made water tight etc. complete as per drawing and instructions.

SQM

Page 16: items list.xlsx

45 44.60 0.00

56 1.00 0.00

57 1470.25 0.00

Providing, fabricating and fixing 12mm thick decorative / clear toughened glass with edge polished and prepared for patch fittings with required designs approved in frosting & etching dimensions as shown in drawings for staircase railing. The fixed glazing shall be supported by connecting profiles etc. all the patch panels, connectors and other accessories should be SS brush finish. All joints shall be sealed with silicon based seal and made water tight etc. complete as per drawing and instructions.

SQM

Providing and fixing sensor based glass revolving / sliding door control system as approved and as per drawings NOS.

Providing and fixing at all levels Curtain wall glazing system with colour anodized Aluminium sections (minimum anodic coating of 20 micron) for main frames (tubular shape) consisting of horizontals and vertical designed to withstand wind pressure up to 150 kg/sqm in additions to supporting dead load are provided. Assembly is made to ensure proper drain of water. Frame work is made with vertical and horizontal tubular sections with provision for weather stripping, joints are provided to ensure water drain system complete as approved by consultant / EIC as per following material details. Aluminium Frame :- Aluminium Frame :-a) Vertical :- 100x55 (2.2 kg/mt) b) Horizontal :- 62x55(1.8 kg/mt) c) Glazing plate :- 6x55 (0.53 kg/mt) d) Cover channel :- 15x56 (0.32 kg/mt) e) EPDM gasket is fixed on all four edges of glass ensure proper holding and water tightness.Glass:- a) 6 mm plain tinted or reflective glass as approved by EIC will be provided. b) The glass to be cut square as per required size and edges are grinded. c) Coated surface shall be inside. It shall not be allowed to have direct contact with any metal. Hardware :-a) Holding down bolts shall be 10 mm dia S.S. or M.S.(b) SS bolts shall be used to clamps aluminium vertical. The rate should include for providing 20% openable panels with SS heavy-duty friction stay and multi-point latching and acremone handle.

SQM

Page 17: items list.xlsx

58 2192.88 0.00

Providing and fixing at all levels 4 mm thick Aluminium composite panel consist of two skins of 0.5 mm th. aluminium and 3 mm sandwich polyethylene core fixed in walls and soffits. As per drawing and design as approved by Consultant / EIC of Alstrong / Alcobond or equivalent make Fabrication and erection of ACP is with the following materials details. including scaffolding but excluding structural steel work Anchor bolt, size 8x78mm make kundan or equivalent.Aluminium angle 50x50x3mm, make final/ indult/ hidalgo.Aluminium cleats 25x25x0.75mm make final/ indult/ hidalgo.Pop rivets 4mmx20mm long make pooja.Silicon weather proof 789 make Dow corning.Backer rod, 15mm make supreme.Nylon / Aluminium shims of standard variety as isolators for packing to adjust the plumb.Fabrication with Hitachi or equivalent machine with independent cutting blade, V-groove blade & V-notch blade complete

SQM

Page 18: items list.xlsx

73 5892.03 0.00

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling CP brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and paneling to be paid for separately.For fixed portion,Powder coated aluminium (minimum thickness of powder coating 50 micron)

KG

Page 19: items list.xlsx

75 60.00 0.00

76 5910.03 0.00

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.In ladders & swan neck type pipe

KG

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

KG

Page 20: items list.xlsx

97 2786.02 0.00

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade.New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm).Aluminium Frame :-a) Vertical :- 100x55 (2.2 kg/mt)b) Horizontal :- 62x55(1.8 kg/mt) b) Horizontal :- 62x55(1.8 kg/mt) c) Glazing plate :- 6x55 (0.53 kg/mt) d) Cover channel :- 15x56 (0.32 kg/mt) e) EPDM gasket is fixed on all four edges of glass ensure proper holding and water tightness. Glass:- a) 6 mm plain tinted or reflective glass as approved by EIC will be provided. b) The glass to be cut square as per required size and edges are grinded. c) Coated surface shall be inside. It shall not be allowed to have direct contact with any metal.Hardware :- a) Holding down bolts shall be 10 mm dia S.S. or M.S. b) SS bolts shall be used to clamps aluminium vertical. c) All gaskets, packing shall be EPDM, Neoprene of nylon for long life. The rate should include for providing 20% openable panels with SS heavy-duty friction stay and multi-point latching and acremone handle.

Cm/M

Page 21: items list.xlsx

73 5892.03 0.00

S.No. Particular of Items Quantity Unit RATE AMOUNTProviding and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling CP brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and paneling to be paid for separately.For fixed portion,Powder coated aluminium (minimum thickness of powder coating 50 micron)

KG

Page 22: items list.xlsx

75 60.00 0.00

76 5910.03 0.00

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.In ladders & swan neck type pipe

KG

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

KG

Page 23: items list.xlsx

97 2786.02 0.00

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade.New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm).Aluminium Frame :-a) Vertical :- 100x55 (2.2 kg/mt)b) Horizontal :- 62x55(1.8 kg/mt) b) Horizontal :- 62x55(1.8 kg/mt) c) Glazing plate :- 6x55 (0.53 kg/mt) d) Cover channel :- 15x56 (0.32 kg/mt) e) EPDM gasket is fixed on all four edges of glass ensure proper holding and water tightness. Glass:- a) 6 mm plain tinted or reflective glass as approved by EIC will be provided. b) The glass to be cut square as per required size and edges are grinded. c) Coated surface shall be inside. It shall not be allowed to have direct contact with any metal.Hardware :- a) Holding down bolts shall be 10 mm dia S.S. or M.S. b) SS bolts shall be used to clamps aluminium vertical. c) All gaskets, packing shall be EPDM, Neoprene of nylon for long life. The rate should include for providing 20% openable panels with SS heavy-duty friction stay and multi-point latching and acremone handle.

Cm/M

Page 24: items list.xlsx

100 10.00 0.00

S.No. Particular of Items Quantity Unit RATE AMOUNTProviding and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete ( with five years service gurantee) Serrated with central bulb (225mm wide, 8-11mm thick).

RM

Page 25: items list.xlsx

151 100.00

S.No. Particular of Items Quantity Unit RATE

Providing and fixing 0.5 mm thick Colour Coated Profiled Sheet (make and colour as approved) of Reputed manufacturers, the base metal for colour coated galvalume substrate steel sheet should have a minimum yield strength of 345 Mpa (50000 psi) and shall confirm to the physical specification of ASTM A 446 (Grade D)/ A653 (Grade50) with galvalume coating confirming to ASTM A 792-AZ 150 (150 gm/sqm). The colour painting shall consisting of backed enamel Polyester with film th. 1.0mil and 0.5mil on other side. Sheet is to be fixed with min. 150mm overlap allowed only over purlins/runners on Roof, gables and long walls with all accessories like no.14 type Self Taping screws & Self Drilling & Taping Screws (SDST), EPDM washers, Butyl sealing tapes 6x5mm between sheet to sheet at all side, Silicon sealant, Ethylene Polyprop.Tepolymer Clousers, ridge curves, corner flashing, end, drip trim, masonry trim, eave, gable end (with closer and sealant), opening flashings wherever required.

Sqm

Page 26: items list.xlsx

0.00

AMOUNT