itw devilbiss table of contents - fluid airfluidair.com/html/pdf/a section-devilbiss2007-2.pdfitw...
TRANSCRIPT
Spray Guns-Packages-AccessoriesMaximum Performer Features and Benefits .................................................................. 1JGHV Standard Size .................................................................................................... 2JGA-HVLP Suction Feed.............................................................................................. 3MSV Mid-Size .............................................................................................................. 4TGHV Detail/Touch-Up ................................................................................................. 5GFG-HVLP Gravity Feed .............................................................................................. 6GTiTMMillennium/Suction Feed ..................................................................................... 7EXL HVLP Pressure Feed Spray Gun........................................................................... 8EXL HVLP Suction Feed Spray Gun ............................................................................. 8EXL HVLP Gravity Feed Gun ........................................................................................ 9EXL SRi HVLP Spray Gun ............................................................................................ 9FinishLine Gravity and Suction Feed .......................................................................... 10VTZ HVLP Spray Gun ................................................................................................ 11EGHV Touch-Up Maximum Performer ........................................................................ 12Air Cap & Tip Selection Chart ................................................................................ 13-14Air Cap Test Kits ........................................................................................................ 15MBC-510 Manual Spray Gun ...................................................................................... 16JGA-Plus Standard Size Manual Spray Gun .......................................................... 17-18MSA Mid-Size Manual Spray Gun .............................................................................. 19EGA Touch-Up Manual Spray Gun .............................................................................. 20Other Equipment and Accessories ............................................................................. 21Spray Equipment Packages .................................................................................. 22-23Solvent SaversTM Hose/Gun Cleaners ......................................................................... 24Fluid Strainers and Equipment ................................................................................... 24Selecting Air Cap, Fluid Tip and Needle ...................................................................... 25Air Cap Selection Guid ............................................................................................... 26Fluid Tip and Needle Selection Guide ......................................................................... 27
Tanks and CupsDeVilbiss Tank/Binks Tank Crossover Chart (cont’) .................................................... 28Pressure and Suction Feed Cups ............................................................................... 29KB Series Pressure Feed Cups ................................................................................. 30
Clean Air Filtration-AccessoriesCentrifugal Filter-Regulator Units ................................................................................ 31Coalescer Filter-Regulator Units ............................................................................ 32-34Three-Stage Desiccant Unit ........................................................................................ 36Whirl-Wind In-Line Filter ............................................................................................. 36CleanAir Air Regulators .............................................................................................. 36Air Control Accessories .............................................................................................. 37Air VizorTM ......................................................................................................... 38-39
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
ITW DeVilbiss Table of Contents
1
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Maximum Performer Features and BenefitsDurability
300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harsh,self-etching primers.
• Dual-seal fluid inlet assures apositive seal.
Drop forged aluminum gun bodiesare strong, durable and lightweight.
Lightweight and precision-balanced for operator comfort.
• Maximum Performer sprayguns are sized to fit both theoperator and the application,with standard-size, mid-sizeand detail/ touch-up models.
2
8
7
9
10
Maintenance• Simple, straightforward design for
easy care and maintenance.
• Economical replacement parts areavailable and easy to install.
64
10
8
13
9
72
5
3
5
6
41 Replaceable anodized aluminumbaffle with air cap retaining ringthreads eliminates the need toreplace the gun body shouldthreads become damaged.
Redesigned trigger strike padmakes trigger action smootherand extends air valve life.
• Cartridge-type air valve isdesigned for positive sealingand quick triggering action.
• All gun components have beenlife cycle tested to ensurereliability in productionenvironments.
PerformanceGoldMax™ air caps and specialfluid tip, needle and bafflecombinations provideunparalleled atomization.
• Collectively, MaximumPerformer spray guns canhandle more than 90% of thematerials and coatings beingapplied today, including highersolids materials and higher fluidflows.
Long-life needle packings requirefewer adjustments.
Easy to UseLight trigger action for easyoperation and comfort.
Knurled knobs for easy adjustment of pattern and fluidflow.
1/4" air inlet connects to anystandard compressor system.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted2
Spray Guns-Packages-Accessories
Our JGHV Standard-Size MaximumPerformer manual spray gun gives youthe best of everything -- the comfortablefit and feel of DeVilbiss’ classic JGAspray gun combined with the hightransfer efficiency and superioratomization of HVLP.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
Productivity and FinishQuality
The productivity and finish qualityof any Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.
Technical SpecificationsBody: Drop forged aluminumWeight: 20.8 oz (599 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 3/8” NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-246Gun Repair Kit: KK-4987-2
Accessories• Remote Cups
Two-quart remote cups are availablein aluminum (KB-555) or stainlesssteel (KB-545-SS).
• Attached CupsOne-quart attached cups are avail-able in aluminum with Teflon®lining (TLC-576) or stainless steel(TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be ordered separately.
• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.
JGHV Standard-Size Maximum Performer
The versatile JGHV gun delivers a highquality finish with less overspray thanconventional guns.
Ordering Information
The JGHV Standard-Size MaximumPerformer manual spray gun is availablewith the following air cap and fluid tipset-ups, factory assembled for immediatedelivery.
Part No.JGHV-531-28FF* JGHV-531-46FXJGHV-531-28FX* JGHV-531-3-46FF**JGHV-531-33FF* JGHV-531-3-46FX**JGHV-531-33FX* JGHV-531-83DJGHV-531-46FF* JGHV-531-83E*Standard tips and needles are 400-gradestainless steel**Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tips.
When ordering DeVilbiss spray guns, the partnumber includes information on the specificgun model, air cap and fluid tip you willreceive.
Example: JGHV-531-
Fluid Tip SizeAir Cap Number
Basic Gun Model
Note: JGHV-531-46FF has been tested and verified in U.S.E.P.A. Environmentalverfication program under contract #DAAE30-98-C-1050 with the U.S. Army(TACOM-ARDEC) via EPA Inter-Agency Agreement #DW97936814.See WWW.EPA.GOV/ETV Note: JGHV-531-46FF
NSN#4940-01-315-8352
3
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Ordering InformationThe Classic Series JGA-HVLP
suction feed spray gun is availablewith the following air cap and fluidtip set-ups, factory-assembled forimmediate delivery. Standard tipand needle are 400-grade stainlesssteel.
Part No.JGA-510-57D*
JGA-510-57DE*
* Cup not included. Order separately.
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.
The JGA-HVLP suction feed spraygun offers easy-to-use suction feedoperation with the high transferefficiency of HVLP. That means youget the flow rates and uniform spraypatterns you want using conventionalsuction feed fluid delivery.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
Technical SpecificationsBody: Drop forged aluminumWeight (Less Cup): 21.4 oz (608 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages:300 grade stainless steelFeed Type: Suction feedService Bulletin: SB-2-248Gun Repair Kit: KK-4987-2
JGA-HVLP suction feed provides highquality atomization with the hightransfer efficiency of HVLP.
Accessories• One-quart paint cups available in
Teflon®-lined aluminum (TLC-555),aluminum (TGC-545) and stainlesssteel (TSC-595).
• One-pint aluminum cup (TGC-536)is also available.
• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.
Productivity and FinishQuality
The productivity and finish qualityof any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.
Basic GunModel
Air Cap Number
Fluid Tip Size
Example: JGA-510-
JGA-HVLP Suction FeedClassic Series Spray Gun
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted4
Spray Guns-Packages-Accessories
MSV Mid-Size Maximum PerformerManual HVLP Spray Gun
Our MSV Mid-Size MaximumPerformer spray gun delivers the samehigh transfer efficiency and superiorperformance as the standard-sizedmodel, only in a smaller package.Weighing only 17 ounces, theMid-Size Maximum Performer spraygun is lighter, and it helps reduceoperator fatigue while providingexcellent comfort and control.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
Ordering Information
TM
Technical SpecificationsBody: Drop forged aluminumWeight: 17 oz (476 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-243Gun Repair Kit: KK-4987-2
Accessories• Remote Cups
Two-quart remote cups areavailable in aluminum (KB-555)or stainless steel (KB-545-SS).
• Attached CupsOne-quart attached cups areavailable in aluminum withTeflon® lining (TLC-576) orstainless steel (TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be orderedseparately.
• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.
* Standard tips and needles are 400-gradestainless steel. 300-grade tips and needles(MSV-531-3) should be used for materialswith pH less than 7.** Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tip.
When ordering DeVilbiss spray guns,the part number includes informationon the specific gun model, air cap andfluid tip you will receive.
Example: MSV-531-
Air Cap NumberFluid Tip Size
Basic Gun Modelw/400 gr. stainless fluid tip, needle
Productivity and FinishQuality
The productivity and finish quality ofany Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.
The lightweight MSV spray gun isdesigned for maximum operatorcomfort.
The MSV Mid-Size Maximum Performermanual spray gun is available with thefollowing air cap and fluid tip set-ups,factory assembled for immediate delivery.
Part No.MSV-531-28FF* MSV-531-83DMSV-531-28FX* MSV-531-83EMSV-531-33FF* MSV-531-3-28FF**MSV-531-33FX* MSV-531-3-28FX**MSV-531-46FF* MSV-531-3-46FF**MSV-531-46FX* MSV-531-3-46FX**
5
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Technical SpecificationsBody: Drop forged aluminumWeight: 19 oz. (530g) TGHV-530
24.5 oz. (690g) TGHV-635 with 8 oz. cup 22.4 (635g)
with 2.5 oz. cupAir Inlet: 1/4" NPS(M)Fluid Inlet: 3/8" NPS(M) - TGHV-530
1/4" NPS(M) - TGHV-635Fluid Passages: 300-grade stainless steelAir Consumption: 6.7 SCFM @ 10 psi air
capAir Requirements: 35 psi inlet=10 psi cap pressureService Bulletin: SB-2-192Gun Repair Kit: KK-5048
TGHV Detail/Touch-Up Maximum PerformerManual HVLP Spray Gun
TM
Part No.TGHV-530-Pressure/Suction Feed*TGHV-635-Gravity Feed*
Our versatile, new TGHV Detail/Touch-Up Maximum Performer spraygun offers superior atomization at thetip, combined with the comfort benefitsof a lightweight, pistol-grip design, sideport fluid inlet for gravity, and standardbottom inlet for pressure/suction feed.
Requiring low air cap pressure, ourTGHV spray gun provides the controlneeded for detail, repair, shading andhighlighting operations. Depending onthe type of feed used, an adjustablespray pattern from 5" to less than 1/4"round makes the TGHV ideal forapplications requiring focused spraypatterns, such as automotive OEM spotrepair, final repair, as well as maskspraying in furniture manufacturing,plastic decorating, and otherapplications requiring small definedpatterns or mask spraying.
• Side port gravity feed with smallerfront end for better operatorvisibility to the spray target.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
• All TGHV series guns utilizemany of the same high qualitycomponents as DeVilbiss JGA,JGV, MSA, and MSV spray guns.
Productivity and FinishQuality
The productivity and finish qualityof any Maximum Performer spray gunis determined by the air cap and fluidtip combination.
The TGHV Spray Gun is availablein both gravity feed and pressure/suction feed models.
•Model TGHV-530 Pressure/Suction Feed Spray Gun.
•Model TGHV-635 Gravity FeedSpray Gun with Cups (2 1/2 oz.and 8 oz. cups included.)
TGHV Accessories• RemoteCups
Two-quart remote cup is available inaluminum (KB-555) or stainlesssteel (KB-545-SS).
• Gravity Cups2 1/2 oz. (TGHV-407-K10) pkg. of10, 8 oz. (KGP-509-1).
• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and
other accessories are also available.
Ordering InformationThe TGHV Detail/Touch-Up Maximum
Performer manual spray gun is available inthe following models, factory assembled forimmediate delivery.
TGHV-635 Gravity FeedSupplied with 8 oz.TGHV-415 SS cup
* Standard tips and needles are 300-gradestainless steel (F) .041".
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted6
Spray Guns-Packages-Accessories
GFG-HVLP Gravity FeedClassic Series Spray Gun
When your application calls forhigher transfer efficiency, but you needmore control of the fluid output than youwould get with a suction feed gun,choose the GFG-HVLP gravity feedspray gun. Combining the quality andperformance of HLVP technology withthe advantages of gravity feed fluidflow, the GFG-HVLP spray gun assuresvirtually every drop in the cup is used,so there’s no waste. Clean-up is quickand simple, too.
With gravity feed, atmosphericpressure and gravity itself force thenewer, higher solids materials into thefluid passage, making the gun moreefficient than suction feed. Less air cappressure is required, too.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
• Standard equipment includes 20 oz.nylon cup and booth-mount gunhook.
• Drip check in the cup lid preventsleaks and spills from vent hole.
Productivity and Finish QualityThe productivity and finish quality
of any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.
Ordering InformationClassic Series GFG-HVLP gravity
feed spray guns are available with thefollowing air cap and fluid tip set-ups,factory-assembled for immediatedelivery. A new 20 oz. acetal gravity cupis included. Standard tip and needle are400-grade stainless steel.
Part No.GFG-618-57DFFGFG-618-57DFW
When ordering Devilbiss spray guns, thepart number includes information on thespecific gun mode, air cap and fluid tipyou will receive.
Example: GFG-618
Fluid Tip SizeAir Cap Number
Basic Gun Model(including cup)
Technical SpecificationsBody: Drop forged aluminumWeight (Gun & Cup): 27 oz (768gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 3/8” BSP (F)Fluid Passages: 300 grade stainlesssteelFeed Type: Gravity feedService Bulletin: SB-2-169Gun Repair Kit: KK-5025
Accessories• 8 oz. nylon cup (KGP-510-1).• 32 oz. aluminum cup (GFC-502).• Workbench gun holder (GH-505)
holds the gun upright to facilitatefilling.
• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.
For smaller production jobs, GFG-HVLPprovides the quality and performance of HLVPtechnology with the advantages of gravity fluidflow.
7
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
GTiTM
MillenniumGTiTM
Compliant HVLPSuction Feed
� Precision engineered #2000 gold air cap - meetsexacting performance demands, producing an extremelyfine finish with all materials. Developed in conjunctionwith top American and European automotive paintcompanies to spray the latest materials.
� Optimum atomization for clearcoats and single stagesProduces high gloss finish and minimizes orange peel.Excellent fluid control for applying more film build withfewer passes.
� Lightweight and comfortable. Classic JGA fit and feel,yet lighter weight. Gun body styling changes forimproved comfort
� Easy to clean - Plated gun body is gun washer safe andmaintains its “like new” appearance.
� Quick cleanup and upside-down spraying (with nocup lid leaks) - with E-Z LinerTM disposable cup liners.
� GTi Millennium HVLP Spray Gun includes: 1.3mm,1.4 mm, and 1.5 mm fluid tips; 32 oz. aluminum cup(120175/GFC-502) with push on lid; air adjusting valvewith gauge (180006/HAV-01); air cap cleaning kit, spraylube, fluid filter, gun hook; (9) E-Z Liner disposableliners (190966/OMX-70-K48)
� Waterborne compatible - stainless steel fluid tip andneedle, electroless nickel-plated gun body inside andout.
� Lightweight and comfortable - familiar JGA fit andfeel, yet 24% lighter.
� Accurate, repeatable settings - pointers on fluidand fan controls.
� Virtually maintenance-free! - No gaskets,self-sealing.
� Simple, easy-to-use suction feed operation allowspainters to spray with the method they’re used to.
� GTi suction feed gun includes:TGC one quart-cupAir adjusting valve with gauge.
GTi Compliant Suction FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications
170146 2.0 20-25 psi Base coatsGTI-600S 25-30 psi Low and high solids,
clear coats, singlestages
Test
ed/V
erifie
d ETV
/EPA
See W
WW
.EPA
.GO
V.ETV
GTi Millennium Gravity FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications
170156 1.3 & 1.4 20-25 psi Base coatsGTI-620G 25-30 psi High solids clear coats(includes 1.3 & 1.4 mm and single stagesand 1.5 mm fluid tips)
1.5 20-25 psi Base coats25-30 psi Low solids, clear
coats, single stagesand waterbornes
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted8
Spray Guns-Packages-Accessories
EXLHVLP Pressure FeedSpray Gun� Precisionengineered patented#2000 air cap - Meetsexacting performancedemands, producing anextremely fine finish withall materials. Developed inconjunction with topAmerican and Europeanpaint companies tospray the latest materials.
� Large Spray Pattern forfast coverage.
� Even distribution ofmaterials for no mottling or striping - Excellent colormatching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
Technical Specifications
Inlet Air AirModel No. Tip (mm) Cap Applications
EXL-520P-11 1.1 2000 Low to medium solidsUp to 12 oz./min.
EXL-520P-14 1.4 2000 High solidsUp to 12 oz./min.
EXL-520P-18 1.8 2000 High solidsUp to 16 oz./min.
EXL-520P-22 2.2 2000 High solidsUp to 18 oz./min.
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
EXLHVLP Suction Feed
Spray Gun
� Precision engineered patented#2000 air cap - Meets exactingperformance demands, producing anextremely fine finish with all materi-als. Developed in conjunction withtop American and European paintcompanies to spray the latestmaterials.
� Large Spray Pattern for fastcoverage.
� Even distribution of materials forno mottling or striping - Excellentcolor matching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Technical Specifications
Inlet Air AirModel No. Tip (mm) Cap Applications
EXL-520S-18 1.8 2000 Base coat 20-25 psiinlet pressure
EXL-520S-22 2.2 2000 Low and high solidsclear coats and singlestages 25-30 psiinlet pressure
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
9
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
EXLHVLP Gravity Feed
Spray Gun� Precision engineeredpatented #2000 air cap - Meetsexacting performance demands,producing an extremely fine finishwith all materials. Developed inconjunction with top Americanand European paint companies tospray the latest materials.
� Large Spray Pattern for fastcoverage.
� Even distribution of materi-als for no mottling or striping -
Excellent color matching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
� Less time spent on refills - True 1-Liter aluminum cupwith disposable push-on lid
� Quick clean up and upside down spraying (no cupleaks) - with E-Z LinerTM disposable cup liners
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Technical Specifications
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications
EXL-620G-15 1.5 20-25 psi Base coat25-30 psi Low solids clear coats
single stagesEXL-620G-18 1.8 20-25 psi High solids and
25-30 psi single stages
EXL-620G-22 2.2 20-25 psi High solids and25-30 psi single stages
DeVilbiss SRiTM
HVLP Spray Gun
Fine Atomization and Spot Repair Versatility
Finally - a spot repair spray gun with the control needed forspot repairs plus the comfort of a full-size spray gun. TheDeVilbiss SRITM is the ultimate spot repair spraygun with the fit and feel of a full size spraygun combined with the pattern range andversatility needed for invisible, top qualityspot repairs.
Maximum Control Means MaximumPerformance� Small gun proportions� Ergonomically styled for operatorcomfort� Full fan and spot patterns for spray
versatility� Full size air and fluid controls� Cheater value for precision air adjustments at
the spray gun.� Single finger trigger adjusts from fine feathering to
fadeouts� Uniform material distribution
Includes:1.0 mm fluid tip or 1.2 mm tip, 4 oz. disposable cup and lid. Wrench(SRi-50), Spray lube (SSL-10)
Specifications:29 psi air inlet pressure delivers 10 psi air cap pressure at 4.5 cfmair volume required. (SRi-5033-205) Air Cap test Kit (orderseparately) Provides consistent setup and regulatory proof of aircap pressure.
*Note: For finer control at lower fluid flows, order the optional .8mm tip and needle separately.
Technical Specifications
Maximum Air Pressure: 100 psi (7 bar)Gun Body: Anodized AluminumNozzle and Needle: Stainless SteelCup: NylonCup Lid: PolypropyleneAir Inlet Size: Universal 1/4” BSP & NPS (M)Gun Weight: 13.7 oz.Gun Repair Kit: SRi-426
Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications
SRi-628-10 1.0 20-29 psi Spot repairs
SRi-628-1.2 1.2 20-29 psi Panel repairs,Door jambs
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted10
Spray Guns-Packages-Accessories
FinishLineGravity Feed
FinishLineSuction Feed
� Economically-priced
� Available in conventional or compliant HVLP models
� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.
� Precision engineered to produce well atomized,uniform spray patterns
� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.
� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.
� 20-oz. lightweight acetal cup with screw-on lid:Built-in “drip check” helps prevent leaks through lidvent hole.
� Quick clean-up and upside-down spraying with no cupleaks with E-Z linerTM disposable cup liners.
Order No. Type Fluid AirModel No. Tip (mm) Cap Applications
FLG-695-113 Conventional 1.3 #1 General purpose,light to heavy
viscosity materials
FLG-695-113 Compliant 1.8/1.5* #3 General purpose,HVLP light to heavy
viscosity materials
* Compliant HVLP models come standard with two sizes of fluid tips
Order No. Type Fluid AirModel No. Tip (mm) Cap Applications
FLG-694-115 Conventional 1.6 #1 General purpose,light to medium
viscosity materials
FLG-693-322 Compliant 2.2/1.8* #3 General purpose,HVLP light to medium
viscosity materials
* Compliant HVLP models come standard with two sizes of fluid tips
� Economically-priced
� Available in conventional or compliant HVLP models
� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.
� Precision engineered to produce well atomized,uniform spray patterns
� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.
� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.
� TGC one-quart aluminum “drip-free” suction cup:Two position valve allows operation as a “drip-free”cup or as a conventional suction cup. “Drip-freediaphragm” helps prevent leaks through lid vent hole.
11
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
VTZ HVLP Spray Gun
� Reduced mottling with dye and toner stains� 99% color repeatability of most NGR stains� Uniform coverage of top coats� 50% less trigger pull
Working in conjunction with coating companies andfurniture manufacturers, DeVilbiss atomization engineershave designed an innovative solution to reduce the inci-dence of mottling, a cloudy or blotchy finish appearancetypically seen when spraying various non-grain-raising dye,toner stains, and semi wipes with standard HVLP guns. Thegun also achieves outstanding results when applying lightto medium topcoats with a viscosity between 18 and 28seconds on a No. 2 Zahn.
The new DeVilbiss VTX spray gun uses a unique andpatented 3-stage atomization technology to overcome theeffects of mottling. Independent testing has confirmed theVTX products:
� Highly consistent, uniform spray patterns� Enhanced process control capability� Improved finish quality and appearance� Additional operator comfort with a 50% reduction indynamic trigger pull.
The VTZ is designed to handle both thin and thick woodfinishing stains and is the first DeVilbiss product to use JetImpingement Atomization (JIA) technology. In this process,the stain is:
1.hydraulically pre-atomized in an internal impingementorifice, creating a vortex.
2.a hollow fluid bulb is then formed as a result of thevortex; and
3.the stain is finely atomized with a 2000 air cap and bafflecombination.
These steps ensure highly consistent and uniform spraypatterns. The VTX design also provides maximum transferefficiency and complies with rules issued by SCAQMD andother air quality authorities.
Ordering Information
The VTZ spray gun set up has two fluid needle and nozzleset-ups for these applications, and is equipped with an in-line 100 mesh mini-strainer to ensure a clean supply ofmaterial to the internal impingement chamber.
Model No.VTX-18 (Use with flow rates at 15 oz/min. or lessVTX-30 (Use with flow rates from 15 to 30 oz/min.
Model No.VTX-18 (Use with flow rates at 15 oz/min. or lessVTX-30 (Use with flow rates from 15 to 30 oz/min.
Fluid Nozzle Assembly
Technical Specifications
Maximum Air Pressure 100 PSI
For HVLP Compliance 30 PSI static, inlet pressure
delivers 10 psi air cap pressure
at 16 cfm
Maximum Fluid Inlet Pressure
60 PSI
Gun Body Drop Forged Aluminum
Wetted Parts Stainless Steel, Delrin
Air Inlet Size 1/4” NPS (M)
Fluid Inlet Size 3/8” NPS (M)
Weight 21.6 oz (610 g)
Feed Type Pressure
Service Bulletin SB-2-282
Gun Repair Kit KK-5085
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted12
Spray Guns-Packages-Accessories
EGHV Touch-Up Maximum Performer
Comfortable and easy-to-use, the EGHV Touch-UpMaximum Performer spray gun provides precise control forthe most exacting detail and touch-up work. The gun featuresa long tapered fluid needle and a top-mounted trigger, andweighs only 7.5 ounces, making it ideal for hours offatigue-free precision painting.• Fluid delivery by attached suction feed or remote
pressure feed cup.• Knurled knobs for fine adjustment of fluid flow and
spray pattern.
Productivity and Finish QualityThe productivity and finish quality of any Maximum
Performer spray gun is determined by the air cap and fluid tipcombination.
Ordering InformationThe EGHV Touch-UP Maximum Performer manual spray
gun is available with the following air cap and fluid tip setup,factory assembled for immediate delivery.
Part No:EGHV-531-397E*
*All wetted surfaces of EGHV are stainless steel
Technical Specifications
Body: Drop forged aluminumWeight: 7.5 oz. (210 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 1/4” NPS (M)Fluid Passages: Stainless SteelFeed Type: Suction feed
Pressure feedAir Consumption: 4.3 CFM max. @
10 psi cap pressureAir Cap Pressure: 10 psi @ 80 psi inletService Bulletin: SB-2-166Gun Repair Kit: KK-5044
EGHV Accessories• 8 Oz Cup (TGS-503) Solvent-resistant
polyethylene cup is available.• Remote Cups
Two-quart remote cups are available inaluminum (KB-555) or stainless steel(KB-545-SS)
• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and otheraccessories also are available.
EGHV-532 gun and TGS-503 translucent polyethylenecup provide a precision finish with less overspray.
HVLP Spray Gun
13
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Air Cap & Tip Selection ChartJGHV, MSV and AGXV
Medium solidsenamels, urethanes,solvent and water-borne furnituretopcoats, waterborneautomotive OEMfinishes, corrosionprotective coatings,leather stains, acrylics,epoxies, etc. 22.5 CFM
** Recommended Fluid Tips Shown. Other Sizes Are Available.* Viscosity Cup Reference18 Seconds #4 Ford = 22 Seconds ZAHN #222 Seconds #4 Ford = 24 Seconds ZAHN #228 Seconds #4 Ford = 30 Seconds ZAHN #2
Low solids automotivefinishes, enamels,lacquers, stains,sealers, etc. 9" FX (.042")
18.75 CFMUp to
12 oz./min.
12-16 oz./min.
11" FF (.055")
Medium-high solidsenamels, urethanes,low VOC waterbornefurniture topcoats,porcelain enamel,corrosion protectivecoatings, acrylics,epoxies, etc.,architectural andindustrial maintenancecoatings.
26.0 CFM
Low solids up to25% solids byvolume
Up to 24 seconds,#4 Ford cup
Low-medium solids,up to 50% solids byvolume
Up to 28 seconds,#4 Ford cup
Medium-high solids,up to 72% solids byvolume
Over 28 seconds,#4 Ford cup
#46 MP
JGHV-101-46MP
#83 MP
JGHV-101-83MP
TYPICALCOATINGSUSED WITH
*TYPICALSOLIDS BYVOLUME
VISCOSITIES
AIR CAPMODEL NO.
PART NO.
AIRVOLUME(AT 10 psiAIR CAP
PRESSURE)
TYPICALFLUIDFLOWRATES
#33A
JGHV-101-33A
** RECOM-MENDED
FLUIDTIPS
PATTERNSIZE
Over16 oz./min.
13" E (.070") orD (.086")
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted14
Spray Guns-Packages-Accessories
Air Cap & Tip Selection ChartEGHV AND TGHV
** Spray pattern size dependent upon type of feed,material viscosity and air cap pressure.
* Viscosity Cup Reference18 Seconds #4 Ford = 22 Seconds ZAHN #222 Seconds #4 Ford = 24 Seconds ZAHN #228 Seconds #4 Ford = 30 Seconds ZAHN #2
JGA-HVLP
Detail, touch-upenamels, lacquers, etc.
6.7 CFM
Detail, touch-upenamels, lacquers, etc.
E (.070")
8.8 CFMUp to
6 oz./min.
4 oz./min.
F (.041")
Low solids up to25% solids byvolume
Up to 24 seconds,#4 Ford cup
Low solids, up to25% solids byvolume
Up to 24 seconds,#4 Ford cup
#90 HV
CV-39-90HV
TYPICALCOATINGSUSED WITH
*TYPICALSOLIDS BYVOLUME
VISCOSITIES
AIR CAPMODEL NO.
PART NO.
AIRVOLUME(AT 10 psiAIR CAP
PRESSURE)
TYPICALFLUIDFLOWRATES
#397HV
EGHV-439-397HV
** RECOM-MENDED
FLUIDTIPS
PATTERNSIZE
up to 6”
up to 5”
Most common lowsolids, coatings, i.e.,automotive refinishmaterials, enamels,lacquers, stains,sealers, primers,waterborne, etc. 22 CFM
Most common lowsolids coatings, i.e.enamels, lacquers,stains, sealers, primers,waterbornes, etc.
FX (.042")
11 CFMUp to
8 oz./min.
Up to 12 oz./min.(gravity)8 oz./min. (suction)
D (.086")DE (.070”)
Low solids up to30% solids byvolume
Up to 24 seconds,#4 Ford cup
Low solids, up to30% solids byvolume
Up to 24 seconds,#4 Ford cup
#57
JGHV-101-57
TYPICALCOATINGSUSED WITH
*TYPICALSOLIDS BYVOLUME
VISCOSITIES
AIR CAPMODEL NO.
PART NO.
AIRVOLUME(AT 10 psiAIR CAP
PRESSURE)
TYPICALFLUIDFLOWRATES
#98
JGHV-101-98
** RECOM-MENDED
FLUIDTIPS
PATTERNSIZE
11 1/2”
10” - 11”
15
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
• KK-5043 Air Cap Test Kit –Includesair cap and gauge, for use with#397HV air caps only.
• KK-5033-98 Air Cap Test Kit –Includes air cap and gauge, for usewith JGA-HVLP spray gun using #98air caps only.
*Air cap test kits may be required by someair quality agencies. These kits are suppliedwith a special air cap and test gauge todemonstrate actual pressure being used at thecap since it will vary depending on hoselength between the air regulator and gun.This kit can be used as a quality controldevice for consistent spraying each day. Thecap kit should not be used when finishes arebeing applied.
Fluid Tips and Needles
• KK-5033-33A Air Cap Test Kit –Includes air cap and gauge, for usewith or #33A air caps only.• KK-5033-46-MP Air Cap Test Kit –
Includes air cap and gauge, for usewith #46MP air caps only.
• KK-5033-83-MP Air Cap Test Kit –Includes air cap and gauge, for usewith #83MP air caps only.
• KK-5033-90-HV Air Cap Test Kit –Includes air cap, gauge and ring, foruse with #90HV air caps only.
ORDER TIPNUMBER ON FLUID TIP AND NEEDLE SET
For JGHV and MSVAV-2115-FF, FX JGA-4040-FF, FX (1)
AV-2120-D, E, FF, FX JGA-4045-D, E, FF, FX (1)
AV-4915-D, E, FF, FX, G JGA-4056-D, E, FF, FX, G (2)
AV-4920-D, E, FF, FX JGA-4051-D, E, FF, FX (2)
For AGXVAV-2115-FF, FX AGX-4402-FF, FX (1)
AV-2120-D, E AGX-4483-D,E (1)
AV-2120-FF, FX AGX-4600-FF, FX (1)
AV-4915-E, FF, FX AGX-4300-E, FF, FX (2)
AV-4920-D, E, FF, FX AGX-4613-D, E, FF, FX (2)
For EGHVEGA-60-E, F EGA-4000-E, F (1)
For TGHVCV-30-F-HV TGHV-4000-F(5)
TGHV-4001-F(3)
Air Cap Test Kits*
MaximumPerformer
(1) 400-grade stainless steel, fluid tip, 303 grade S.S. Needle (matched set)(2) 300-grade stainless steel with U.H.M.W. polyethylene seat in fluid tip (matched set).(3) Acetal and 300-grade stainless steel tip(4) Composite sprayhead, 400-grade stainless steel needle with U.H.M.W. polyethylene tip.(5) 300-grade stainless steel (matched set)(6) 400-grade stainless steel fluid tip, 303 grade S.S. Needle (matched set)
ORDER TIPNUMBER ON FLUID TIP AND NEEDLE SET
For JGA-HVLPAV-2115-FX JGA-4040-FX (1)
AV-4915 JGA-4056-FX (2)
For GFG-HVLPAV-2115-DFF JGA-4046-14 (6)
AV-2125-DFW JGA-4046-16 (6)
AV-2120-DE AGX-4046-18 (6)
JGA-HVLP (SUCTION)AV-2125-DE JGA-4046-18 (6)
AV-2125-D JGA-4046-12(6)
ClassicSeries
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted16
Spray Guns-Packages-Accessories
Combining a drop forged aluminumbody with a forged removable sprayhead, the MBC-510 spray gun is idealfor applications that require maximumoutput and quick changeovers.• Removable spray head allows for
reduced downtime on nozzlecombination changeovers.
• MBC spray guns have nickel-platedbrass fluid passages and stainlesssteel fluid tip and needle.
• Ideal for zinc coatings• Applications include oil platforms,
corrosion control and bridgemaintenance delivery.
Ordering InformationThe following air cap and fluid tip set-
ups are factory assembled for immediatedelivery.
Part No.MBC-510-30EXMBC-510-64HDE
MBC-510 Manual Spray GunWith Removable-Head
These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:
Part No.MBC-510-DMBC-510-EMBC-510-EX
MBC-510-FFMBC-510-FX
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.
Technical Specifications
Body: Drop forged aluminumWeight: 27 oz. (756 gr) with air
cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS(M)Fluid Passages: Nickel-plated brassWetted Parts: Nickel-plated brass
400-grade stainless steelFeed Type: Pressure feed
Suction feedService Bulletin: SB-2-301Gun Repair Kit: KK-4058-1
Accessories• Hose assemblies, air control, pressure
tanks, cups, gun and hose cleaningequipment and other accessories areavailable.
MBC-510-64HDDMBC-510-704E
Basic Gun ModelAir Cap Number
Example: MBC-510-
Fluid Tip Size
Chart 1 Fluid Tip (Nozzle), AirCap and Needle Combinations
17
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
JGA-Plus Standard SizeManual Spray Gun
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
• The JGA standard -size manual spraygun sets industry standards for high-production performance.
• An economical option for waterborneand solvent-based material applica-tions, the JGA stainless steel airspray gun delivers the quality resultsyou need for tough applications.
• Offers the comfortable fit and feeloperators prefer.
Ordering InformationThe JGA-Plus standard-size spray gun
is available with the following air capand fluid tip set-ups, factory-assembledfor immediate delivery. However, theseare only the most popular set-ups – forother air cap and tip combinations thatcan be ordered separately.
Part No.JGA-510-30EXJGA-510-65HDDJGA-510-704EJGA-510-704FFJGA-510-704FXJGA-510-765E
These guns with fluid tipand needle can be orderedseparately without air capand retaining ring:
Part No.JGA-510-D* JGA-510-FX*JGA-510-E* JGA-510-3-FF**JGA-510-EX* JGA-510-3-FX**JGA-510-FF*
Example: JGA-510-
Basic Gun ModelAir Cap Number
Fluid Tip Size
Technical SpecificationsBody: Drop forged aluminumWeight: 21.6 oz. (613 gr) with air
cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS (M)Fluid Passages: 300-grade stainless steelFeed Type: Pressure feed,
Suction feed (EX)Service Bulletin: SB-2-252Gun Repair Kit: KK-4987-2
Accessories
• Hose assemblies, air control,pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
• For optional tip and needle sets.
JGA-510-765FFJGA-510-765FXJGA-510-797EJGA-510-797FFJGA-510-80EXJGA-510-797FX
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted18
Spray Guns-Packages-Accessories
JGA-Plus Standard SizeManual Spray Gun (cont’)
JGA/MSA-TEK offers a simpleconversion to HVLP pressure feed by
changing the air cap, baffle and bafflegasket.
• Maximum 8 oz./min. fluid flow.• Lower solids coatings.• Medium to high V.O.C. coatings
(4.0-5.0 lbs./gal.).• Smaller compressors - 3 h.p. is
usually sufficient.• Limited air supply - requires only
11 CFM at 10 PSI air cappressure.
• Class “B” finish qualityrequirements.
JGA-HVLP and MSA-HVLP Application GuideThe economical way to convert
DeVilbiss conventional air spray gunsto Classic Series HVLP performanceby using a conversion kit. Simple toconvert for on-site retrofit.
19
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Technical Specifications
Body: Drop forged aluminum Weight:18.4 oz. (515 gr)
Air Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 150 psi max, 3/8" NPS (M)Fluid Passages: 300-grade stainless steelWetted Parts: 300 and 400-grade
stainless steel, hardened alloyFeed Type: Pressure feedService Bulletin: SB-2-319Gun Repair Kit: KK-4987-2
Designed to help reduce operatorfatigue while offering excellentcomfort and control, the MSA midsizespray gun is lighter and more compactthan our standard-size JGA gun. Thatmeans you get the same quality andhigh-efficiency performance providedby our JGA-Plus spray gun, in asmaller model that weighs only 17ounces.• 300-grade stainless steel fluid
passages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
• Air caps and replacement parts areinterchangeable with JGA sprayguns (the air inlet fitting is the onlyexception).
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun are determined by the aircap and fluid tip combination.
Ordering InformationThe MSA midsize spray gun is
available with the following air cap andfluid tip set-ups, factory-assembled forimmediate delivery. However, these areonly the most popular set-ups – for otherair cap and tip combinations that can beordered separately.
Part No.MSA-510-35LEMSA-510-35LFFMSA-510-35LFXMSA-510-704LE
Decorator Spray GunMSA-510-DEC
The MSA-510-DEC decorator spraygun features a spatter cap to createdecorative textured finishes.
Can be converted to HVLP.
These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:
Part No.MSA-510-E*MSA-510-EX*MSA-510-FF*MSA-510-FX*
MSA-510-3-E**MSA-510-3-FF**MSA-510-3-FX**
MSA-510-704LFFMSA-510-704LFXMSA-510-797LEMSA-510-797LFF
* Models include 400-gradestainless steel tips and needles.** Models include “premium”300-grade stainless steel tip withU.H.M.W. polyethylene insert(needle seat) and 300-gradestainless steel needle.
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gunmodel, air cap and fluid tip youwill receive.
Technical SpecificationsBody: Drop forged aluminumWeight: 17 oz. (476 gr)Air Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS (M)Fluid Passages: 300-grade stainless steelFeed Type: Pressure feed
Suction feedService Bulletin: SB-2-257Gun Repair Kit: KK-4987-2
Accessories• Hose assemblies, air control,
pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
• For optional tip and needle sets.
Example: MSA-510-
Basic Gun ModelAir Cap Number
Fluid Tip Size
MSA Mid-Size Manual Spray Gun
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted20
Spray Guns-Packages-Accessories
EGA Touch-Up Manual Spray Gun
The gun of choice for touch-up,shading, edging and detail decorating,the EGA touch-up gun providesprecise control for any type of delicatespray finishing applications. Designedfor external mixing applications, thegun features a forefinger trigger toenhance operator control, and a longneedle taper to make detail work easy.• Equipped with stainless steel tip
and needle.
• Knurled knobs allow fine sprayadjustments for fluid and patterncontrol.
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination. Body: Drop forged aluminum
Weight: 7 oz. (196 gr) with air capand ring
Air Inlet: 1/4" NPS (M)Fluid Inlet: 1/4" NPS (M)Wetted Parts: Aluminum 400-grade
stainless steelFeed Type: Pressure feed
Suction feedService Bulletin: SB-2-163Gun Repair Kit: KK-5044
Accessories• Hose assemblies, air control,
pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
Note: EGA-503 model replacesEGA-502.
Basic Gun ModelAir Cap Number
Fluid Tip Size
Example: EGA-503-
Ordering InformationThe EGA touch-up gun is available with
the following air cap and fluid tip set-ups,factory-assembled for immediate delivery.
Part No.EGA-503-390F
When ordering DeVilbiss spray guns, thepart number includes information on thespecific gun model, air cap and fluid tip youwill receive.
Technical Specifications
21
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Spray Gun LubeSSL-10-K12
Specially formulated spray gun lubeimproves performance and extends thelife of spray equipment. Contains nosilicones or petroleum distillates tocontaminate paint and coatings. Caseof 12 (2-oz.) bottles. Not for use withair tools and high RPM equipment.
Spray Gun Wrench
WR-103
Versatile tool fits fluid and air hoseconnections, as well as adapters andpacking nuts.
JGA Gun Fluid TubeJGA-444
Handy tube combines the fluid andair hoses at the gun handle to preventtwisted lines and keep hoses fromdragging over work. 3/8” NPS thread.
Disposable Spray Gun CoversSave money by reducing cleaning
time and maintenance with thesecovers that also limit operatorexposure to overspray.GC-100-K4 (pkg. of 4)GC-100-K48 (pkg. of 48)
PART NO. MALE MALE FEMALE
AD-404 – 1/4" NPS 3/8" NPSP-H-4105 – 3/8" NPS 1/4" NPSH-1766 1/8" NPT 1/4" NPS –H-2008 1/4" NPT 1/4" NPS –AD-31 1/4" NPS 1/4" NPS –AD-26 1/4" NPS 3/8" NPS –H-1580 1/4" NPT 3/8" NPS –H-1446 3/8" NPS 3/8" NPS –AD-11 3/8" NPS 3/8" NPT –
Cleaning BrushesFor cleaning the threads and recesses of
the gun body.3/8" dia. brush: 42884-214-K5 (pkg. of 5)5/8" dia. brush: 42884-215-K10 (pkg. of 10)
Thread AdapterThread adapters provide the correct hook-up for spray guns, hoses,
tanks and other spray equipment. They work with most standard threadapplications.
Other Equipment and Accessories
Manual Spray Gun ExtensionsFor hard to reach locations. Attach tomost conventional and HVLP sprayguns. For conventional coatings.Compatible with brass wetted parts.Comes with 1/4” NPS (f) x 1/4” NPS (m)air inlet adapter.Length Part Shipping Actualin feet No. Weight (lbs.) Weight (lbs.)
4 54-296 4 3
6 54-297 5.25 4
8 54-298 6.5 5
Universal Clamp - AGA-415This clamp attaches directly to the gunstud and clamps onto 3/4” rod, allowingthe gun to rotate to an angle. 13.5 oz.(378 gr) shipping weight.
Mounting Stud - AGA-414Use this stud to attach automatic sprayguns to 3/4” rods and increase theflexibility and versatility of your spraysystem. 16” long, 48 oz. (1344 gr)shipping weight
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted22
Spray Guns-Packages-Accessories
Spray Equipment
JGHV-531-46FF (.055)DeVilbiss MAXIMUM PERFORMER HVLP spray gun, medium solids,enamels, top coats, Aerospace, automotive OEM finishes, corrosionprotective coatings, acrylics, epoxies up to 50% solids (12-16 oz.min./28 seconds #4 Ford). Stainless Steel fluid passages and stainless steeltip and needle with 46MP air cap, maximum 11” pattern.
Maximum Performer HVLP spray guns also meet operationalrequirements of California South Coast Air Quality ManagementDistrict and other air quality authorities. DeVilbiss HVLP spray gunsare protected by Patents 5,344,078, 5,209,405 & 5,090,623.
KK-4987-2 Repair Kit. Used on JGHV, MSV, MSA and JGAspray guns
KB-555 - 2 quart aluminum remote pressure cup
KB-545-SS - 2 quart Stainless Steel remote pressure cup
TLC-576 - 1 quart aluminum pressure cup (for attached use)TSC-591 - 1 quart Stainless Steel cup (for attached use)
(must use KK-4980 regulator, purchase separately)
QMGT-5223 - 2 gallon ASME galvanized pressure tank, doubleregulation, agitator and air motor
QMST-5223 - 2 gallon ASME stainless steel pressure tank, doubleregulation, agitator and air motor
KB-4006 - 6 ft. hose sets (air and fluid) with fittings for use withremote KB cups
71-1355 - 3/8” x 25’ I.D. air hose assembly with fittings
71-3303 - 3/8” x 25’ I.D. fluid hose assembly with fittings
71-31101 - 3/8 x 25 I.D. Ergoflex air hose
JGHV Spray Gun
KB Cup
TLC Cup &Regulator
QMGT/QMSTPressure Tank
23
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
FLHVLP-1 Outfit Consists of:(1) JGHV-531-46FF spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4006 6 ft. hose set with fittings
FLHVLP-2 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup(1) KB-4006 6 ft. hose set with fittings
**FLHVLP-3 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4006 6 ft. hose set with fittings
FLHVLP-4 OutfitConsists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup(1) KB-4006 6 ft. hose set with fittings
** 4940-01-363-6937-FLHVLP-613 Outfit same asFLHVLP-3 different cup
FLHVLP-5 Outfit Consists of:(1) QMGT 2 gallon galvanized ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice(1) 71-3303 - 75 ft 3/8 fluid hose(1) 71-1105 - 75’ 1/4 air hose
FLHVLP-6 Outfit Consists of:(1) QMST 2 gallon stainless steel ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice(1) 71-3303 - 75 ft 3/8 fluid hose(1) 71-1105 - 75’ 1/4 air hose
*FLHVLP-7 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TLC-576 attached 1 quart pressure cup(1) KK-4980 pressure regulator
FLHVLP-8 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TSC-591 Stainless Steel attached pressure cup(1) KK-4980 pressure regulator
All outfits may be modified to suit your needs.Other model HVLP spray guns and
ASME pressure tanks available.
* 4940-01-363-6938 - FLHVLP-605 Outfit same asFLHVLP-7
Note: Model JGHV-531-46FF tested/verified ETV/EPA.See WWW.EPA.GOV/ETV
Spray Equipment Packages(fully assembled)
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted24
Spray Guns-Packages-Accessories
Fluid Strainers and Equipment
Solvent SaversTM Hose / Gun CleanersSimple, easy-to-use cleaners speed up
equipment cleaning and save solvent(up to 86% savings!), which reducesV.O.C. emissions. Operate withcompressed air. Provide finely atomizedblast of solvent traveling through fluid
passages of spray guns, hoses, etc.Metering permits varying air/solventmix. Equipped with safety valve. 1/4"NPS (M) air and 3/8" NPS (M) fluidconnections.
Solvent Savers™ Hose/Gun CleanersSHIP WT. MAX. WORKING MATERIAL CONSTRUCTION
PART NO. COMPUTER NO. CAPACITY (LBS.) PRESSURE (IN CONTACT W/FLUID)
*HD-503 180037 2 qt. 5 50 psi Aluminum, nickel plated brass,
Teflon and Thiokol gasket
*QMGZ-5200 2 gal 42 110 psi Galvanized steel, aluminum,
nickel plated brass, Teflon &
Thiokol gaskets, polyethylene
tank liner
*Note: Not suitable for use with chlorinated solvents, such as 1,1,1 trichloroethylene or methylenechloride.
Gun Mounted
Strainer
VS-531
PLH-MF-6-100
Fluid Strainer
PLH-MFC-100
100 Mesh Screen
In-Line
Strainer
VS-534
Fluid Strainers
STRAINER MAX. WORKING INLET OUTLET WETTED SCREEN MESH MICRON
STRAINER TYPE PART NO. PRESSURE THREADS THREADS PARTS PART NO. SIZE SIZE
Gun Mounted StrainersVS-531 300 3/8"NPS(M) 3/8"NPS(F) CS 31144-310-K10 100 149
VS-532 300 3/8"NPS(M) 3/8"NPS(F) PB VS-58-K10 100 149Swivel
Gun Mounted Mini Strainers
PLH-MF-6-100 250 3/8” NPS (M) 3/8” NPS (F) SS PLH-MFC-100 100 149
In-Line StrainerVS-534 300 3/8"NPS(F) 3/8"NPS(M) SS VS-58-K10 100 149
Swivel
SS = Stainless Steel PB = Plated Brass CS = Carbon Steel
Gun Mounted
Strainer
VS-532Designed for use with JGA
spray guns, this strainer
mounts on the fluid inlet and
allows the filter screen to be
cleaned or replaced without
removing the strainer housing.
Lightweight stainless
steel final filter, 250 PSI
maximum working
pressure
Stainless steel swivel
strainer mounts to the
rank or pump and has
a 100 mesh replaceable,
cylindrical filter.
Gravity Gun
Strainer
KGP-5-K5
Gravity Fluid Strainer
Gun Cup Strainer
50-mesh, 149-278
A final strainer for atomized
spray gun cups. The 50-
mesh brass filter screen for all
enamels and lacquers. The
strainer is pressed on and
removed from the end of
the siphon tube. Its gasket
prevents by-pass and holds
firmly on siphon tube sizes
up to 7/16” diameter. Box
of 10.
This strainer is available in 100
mesh and can be attached to
the gun inlet.
25
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Selecting the Air Cap, Fluid Tip and NeedleThe air cap directs compressed air into the
material stream to atomize the fluid and
form the spray pattern. The fluid tip and
needle meter direct the flow of material
from the gun into the air stream.
Because they all affect the quality of the
spray pattern, the air cap, fluid tip and
needle are usually selected as a unit.
Together, these three items are referred to
as the nozzle combination.
Types of Air Caps
Air caps are defined by their methods of
delivering and mixing the spray finishing
materials. Delivery methods include
pressure feed, suction feed and gravity
feed. Chart 1 depicts flow rate range, fluid tip
size and recommended air caps for a typical
product finish.
Types of Fluid Tips
Fluid tips are made from a variety of
metals. The application determines the
type of fluid tip to use. Stainless steel tips
are ideal for corrosive materials. The
standard tip on most DeVilbiss guns is
400-grade stainless steel; 300-grade
“premium” fluid tips with U.H.M.W.
polyethylene insert (needle seat) are also
available. We also offer carbolloy fluid tip
for extremely abrasive materials.
The amount of material discharged from a
pressure feed gun depends on a number
of factors: the material viscosity, the fluid
tip inside diameter, the length and size of
hose, and the pressure on the material.
Generally, the larger the opening, the more
material discharged.
However, if the fluid tip is too large, the
operator will lose control over the material
discharge. And if the fluid tip opening is
too small, the discharge velocity will be too
high. This means the air coming from the
cap will not atomize the material properly,
and the pattern will be distorted.
With a suction feed gun, the fluid flow in
ounces per minute is relatively stable
because it is determined by atmospheric
pressure. It is also determined by the
material viscosity and air cap pressure.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted26
Spray Guns-Packages-Accessories
Air Cap Selection Guide
Conventional Air Spray Guns
27
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Fluid Tip and Needle Selection Guide
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted28
Tanks and Cups
DeVilbiss Tank/Binks TankCrossover Chart (cont’)
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 GravoisSt. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
All Tanks are Featured in Binks Section, Starting on Page 47
PART NO.2 Gallon Replacement Description for Binks Replacement in Galvanized SteelQMGT-5200 83G-210 The SIMILAR replacement has a single regulator, and is branded BinksQMGT-5201 83G-211 The DIRECT replacement has a single regulator, and is branded BinksQMGT-5210 83G-210 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5211 83G-211 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5213 83G-213 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5220 83G-220 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5221 83G-221 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5223 83G-221 The SIMILAR replacement has a direct drive agitatorQMGT-5226 83S-526 The SIMILAR replacement is Stainless Steel and is branded BinksQMGT-5231 83G-221 The regulators on the SIMILAR replacement have a lesser turndown ration.
These are also branded Binks
5 GallonQMGT-5500 83G-510 The SIMILAR replacement has a single regulator, and is branded BinksQMGT-5502 83G-513 The SIMILAR replacement has a single regulator and an air driven/gear reduced
agitator and is branded BinksQMGT-5510 83G-510 The DIRECT replacement is branded Binsk. There are no other differencesQMGT-5512 83G-513 The SIMILAR replacement has an air driven/gear reduced agitator and is
branded BinksQMGT-5513 83G-513 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5520 83G-520 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5522 83G-523 The SIMILAR replacement has an air driven/gear reduced agitator and is
branded BinksQMGT-5523 83G-523 The DIRECT replacement is branded Binks. There are no other differencesQMGT-5530 83G-52 The regulators on teh SIMILAR replacement have a lesser turndown ratio.
These are also branded Binks
10 GallonQMGT-51000 83G-1010 The SIMILAR replacement has a single regulator, and is branded BinksQMGT-51010 83G-1010 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51013 83G-1013 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51020 83G-1020 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51023 83G-1023 The DIRECT replacement is branded Binks. There are no other differences
15 GallonQMGT-51500 83G-1500 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51510 83G-1510 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51513 83G-1513 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51520 83G-1520 The DIRECT replacement is branded Binks. There are no other differencesQMGT-51523 83G-1523 The DIRECT replacement is branded Binks. There are no other differences
29Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Tanks and Cups
Pressure and Suction Feed Cups
Gravity Feed CupsMade of strong, lightweight material
for durability. Features a “dry check”device integral with cup lid to avoidspillage from vent hole.
KGP-509-1 - 8-oz. Cup (Nylon)
GFC-501 - 20-oz. Cup (Delrin)
Polyethylene Suction CupTGS-503
8-oz. cup size. Combines engineeredresin lid with translucent polyethylenecup – liquid level visible. Molded-ingraduations for mixing ratios.Lightweight and easy to clean.Nonstaining. Includes cup closure.Compatible with all solvents. Use withEGA-502, EGHV-530 or any suctionfeed gun with 1/4" NPS threads.
Aluminum Suction CupsAluminum suction cups incorporate a
two-position special lid design – oneas drip-free cup or the other asconventional suction feed cup. Smoothmetal surfaces make cleanup andchanging paint fast and easy. Use withall suction feed spray guns.
TGC-545 - Quart Capacity Suction Cup
TGC-536 - Pint Capacity Suction Cup
Low Pressure Cup for HVLPTLC-576
Aluminum, one-quart, lowpressure cup for HVLP applications.Teflon®-lined for fast, easy cleaning.Solvent-resistant check valve.Requires KK-4980 for cup airregulation. (Order separately)
Teflon®-Lined Suction CupTLC-555
Aluminum, one-quart cup featuringTeflon® lining for fast, easy cleaningand reduced color contamination.Drip-free lid design has two-positionvalve which allows for operation as“drip-free” cup or as conventionalsuction cup. Use with all suction feedspray guns.
Stainless Steel CupsOne-quart cups made from 300
series stainless steel, designed for usewith waterbased materials and exemptsolvents. The .030" wall thicknessmakes it more durable thancompetitive cups, yet still lightweight.And the fluid tube is stainless steel foradded durability and corrosionresistance.
TSC-591 - HVLP Low PressureFeed Cup. Requires KK-4980 for cupair regulation (order separately)
TSC-595 - Suction Feed Cup
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted30
Tanks and Cups
For use with both conventional airspray systems and HVLP systems, theKB II series, two-quart cups feature a“pistol grip” carrying handle, and rightor left-handed design for comfort andease of handling. An easy-open lid andwide cup mouth allow for fast fillingand cleanup. KB Series cups alsofeature a solvent resistant check valveand a wide base for greater stability.
KB series cups are ideal for handlingheavier viscosity materials, higher flowrates, as well as low fluid flow rates of10 ounces per minute or less. Fluidpressure range of 2-30 psi. Order air/fluid hose assemblies separately.
KB-4004 - 4-foot hose length.
KB-4006 - 6-foot hose length mostcoating materials and solvents.
Pressure and Suction Feed CupsCOMPLETE CUP CONNECTION APPROX. SHIP
ASSEMBLY THREAD SIZE CUP AND COVER CUP ONLY WT/ COMPLETE
PART NO. CAPACITY MATERIAL FLUID AIR ASSEMBLY PART NO. CUP AND LID
Pressure FeedKB-555 2 qt. Aluminum 3/8"NPS(M) 1/4" NPS(M) — KB-422 3 lbs. 14 oz.
KB-545-SS 2 qt. Stainless Steel 3/8"NPS(M) 1/4" NPS(M) — KB-442 5 lbs. 2 oz.TSC-591 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.TLC-576 1 qt. Aluminum w/Teflon® Lining 3/8"NPS(F) — TLC-401 18 oz.
Suction FeedTGC-536 6 oz. Aluminum 3/8"NPS(F) — — TGC-432 12 oz.TGC-545 1 qt. Aluminum 3/8"NPS(F) — — KR-428-2 18 oz.TGS-503 8 oz. Polyethylene 1/4"NPS(F) — TGS-406 3 ozTLC-555 1 qt. Aluminum w/Teflon® Lining3/8"NPS(F) — TLC-401 18 oz.TSC-595 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.
Gravity FeedKGP-509-1 8 oz. Nylon 3/8"BSP(M) — — — 3 oz.KGP-510-1 20 oz. Delrin 3/8"BSP(M) — — –– 6 oz.
* Use with GFG and GFHV guns only.** Order KK-4980 Air Regulator Kit in addition to cup.
KB Series Pressure Feed Cups
Aluminum CupKB-555
DeVilbiss KB Aluminum modelcups are compatible with most coatingmaterials and solvents.
Stainless Steel CupKB-545-SS
DeVilbiss KB Stainless Steelmodel cups are designed for usewith waterbornes, halogenatedhydrocarbons and other corrosivematerials.
KK-5051 Disposable CupLiner Kit includes20 liners, 20 lids and 3 rings
31
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Centrifugal Filter-Regulator Units
Excellent for eliminating moistureand dirt from an air supply, DeVilbissCleanAir centrifugal units supplycleaner, drier air to each spray gun in asystem. This cleaner air can alsoincrease the life of pneumatic tools.
• Filters out water and oil aerosols anddirt particulates to 5 microns.
• Ideal for most spray applications, airtools and equipment.
• Water droplets collected in the bowlare removed by an automatic drain(standard feature). No need tomanually drain.
Quick-release filter bowl and spin-off5-micron filter element allow one-minutefilter changes without tools. Pressure dropsare minimized by large air inlet and outletand large internal air passages.
HFRL-511Service Bulletin SB-6-148-E
HAF-502 HAF-503 HFRL-508 HFRL-509
P/N# Service BulletinHAF-502 SB6-146-BHAF-503 SB-6-148-EHFRL-508 SB-6-148-EHFRL-509 SB-6-148-E
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted32
Clean Air Filtration-Accessories
CleanAir Centrifugal Filter-Regulator Units
Accessories• Mounting Bracket Assembly Kits
For HAF-502 air filter and HFRL-508regulator; order HAF-407.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, orderHAF-408.
Centrifugal Air Filter UnitsPART NO. HAF-502 HAF-503
Filtering Capacity (micron) 5 5Flow Rate (CFM) 100 @ 90 psi 150 @ 90 psiMax. Inlet Pressure (psi) 150 150Max. Operating Temp. 150oF 150oFInlet Port Size 1/2" NPT (F) 3/4" NPT (F)Outlet Port Size 1/2" NPT (F) 3/4" NPT (F)Bowl Capacity 17 oz. 34 oz.Shipping Weight 1 lb. 7 oz. 3 lbs. 1 oz.Service Bulletin SB-6-146 SB-6-148
Tornado-like swirling action removes moisturewhich collects in the baffled “quiet zone.”The reusable 5-micron filter catches smallerimpurities. Accumulated liquid is carriedaway by the automatic drain.
Airinlet
Centrifugal Filter-Regulator UnitsPART NO. HFRL-508 HFRL-509 HFRL-511
Filtering Capacity (micron) 5 5 5Flow Rate (CFM) 50+ 80+ 120+Max. Inlet Pressure (psi) 150 150 150Regulated Pressure Range (psi) 0 - 125 0 - 125 0 - 125Max. Operating Temp. 150oF 150oF 150oFInlet Port Size 1/2" NPT (F) 3/4" NPT (F) 3/4" NPT (F)Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (2) 1/4" NPS (M) (4) 1/4" NPS (M)Non-Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M) (1) 1/4" NPS (M)Bowl Capacity 17 oz. 34 oz. 34 oz.Air Filter Included HAF-502 HAF-503 HAF-503Quality Air Regulators/Model (1) HAR-506 (1) HAR-507 (2) HAR-507Air Gauges (0 - 100 psi) 1 1 2Air Gauges (0 - 160 psi) 1 1 1Shipping Weight 9 lbs. 15 lbs. 18 lbs.Service Bulletin SB-6-146 SB-6-148 SB-6-148
Flexibletubing
Automaticdrain
Quietzone
Baffle
Reversible5-micronfilterTornado
swirl ring
• Filter Element Kits (5-Micronreusable)For HAF-502 air filter and HFRL-508regulator; order HAF-6.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, order HAF-15.
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
33
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Coalescer Filter-Regulator Units
HFRL-513Service Bulletin SB-6-148-E
CleanAir coalescer filters removewater, dirt and oil from the systemdown to .01 micron. DeVilbisscoalescer filter units are designedwith a quick-release bowl andspin-off element for filter changeswithout tools. In addition, a filter-change indicator alerts the operatorwhen the element requires changing.
• Borosilicate glass microfiber filter isengineered for high flow, highefficiency, quick change and lowpressure drop.
• Ideal for most spray applications,especially where oil aerosols maybe a problem.
• Automatic bowl drain and 6' hoseeliminate oil and water buildup(standard feature). No need tomanually drain.
The HAF-508 is the coalescer filteronly. In combination with thecentrifugal filter, there are threechoices – the HAF-509 non-regulatedunit and the two regulated models –HFRL-512 and HFRL-513.
HAF-509Service BulletinSB-6-148-B
HFRL-512Service BulletinSB-6-148-E
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted34
Clean Air Filtration-Accessories
CleanAir Coalescer Filter-Regulator Units
Accessories• Mounting bracket assembly kit is
available; order HAF-408.
• Centrifugal filter element kit hasreusable 5-micron filter; orderHAF-15.
• Coalescer filter element kit has.01-micron filter; order HAF-38.
Centrifugal-Coalescer Filter UnitsHAF-508 HAF-509
NON-REGULATED MODELS COALESCER* CENTRIFUGAL& COALESCER
Centrifugal Filtering Capacity (micron) 5 5Coalescer Filtering Capacity (micron) .01 .01Flow Rate (CFM) 150 @ 90 psi 150 @ 90 psiMax. Inlet Pressure (psi) 150 150Max. Operating Temp. 150oF 150oFInlet Port Size 3/4" NPT (F) 3/4" NPT (F)Outlet Port Size 3/4" NPT (F) 3/4" NPT (F)Bowl Capacity 34 oz. 34 oz.Shipping Weight 3 lbs. 2 oz. 6 lbs. 3 oz.Service Bulletin SB-6-148 SB-6-148
Pre-filter support fabric prevents mediamigration, increasing element life. Stainlesssteel screens provide fail-safe protection againstaccidental shock loads and high pressure dropsin either direction. Anti re-entrainment barrierprevents liquid carryover, even in shockconditions, and is compatible with mineral andsynthetic lubricants. A – Easy-fit captive O-ring
Coalescer-Filter Regulator UnitsREGULATED MODELS HFRL-512 HFRL-513
Centrifugal Filtering Capacity (micron) 5 5Coalescer Filtering Capacity (micron) .01 .01Flow Rate (CFM) 80+ 120+Max. Inlet Pressure (psi) 150 150Regulated Pressure Range (psi) 0 - 125 0 - 125Max. Operating Temp. 150oF 150oFInlet Port Size 3/4" NPT (F) 3/4" NPT (F)Regulated Outlets (w/ ball valve) (2) 1/4" NPS (M) (4) 1/4" NPS (M)Non-Regulated Outlets (w/ ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M)Bowl Capacity 34 oz. 34 oz.Quality Air Regulators/Model (1) HAR-507 (2) HAR-507Air Gauges (0 - 100 psi) 1 2Air Gauges (0 - 160 psi) 1 1Shipping Weight 18 lbs. 2 oz. 21 lbs. 2 oz.Service Bulletin SB-6-148 SB-6-148
* HAF-508 coalescer filter should be used in conjunction with a centrifugal type filter to removethe majority of water, oil and dirt, prior to the coalescer filter.
A
B
C
D
E
G
F
B – Corrosion-resistant end capsC – Pre-filter support fabricD – Stainless steel support screensE – Anti re-entrainment barrierF – Borosilicate glass microfiber filter
G – High-strength epoxy sealant
35
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Three-Stage Desiccant Unit
The three-stage desiccant unitprovides the ultimate in clean dry air.First stage centrifugal filter removesparticulates to 5 microns. Stage twocoalescer filters down to .01 micron.Third stage desiccant removesremaining water vapor to a dew pointof -40oF.
• Ideally suited for low to mediumproduction.
• DAD-500 air-drying system includesthree filtering units, as well as a wallmount bracket and desiccant filterchange indicator.
• Centrifugal and coalescer unitsinclude automatic bowl drain(standard feature). No need tomanually drain.
• Coalescer filter includes filter changeindicator
• Desiccant filter includes sight glassindicator (Changes color whendesiccant needs replacement)
DAD-500 Desiccant Air Drying SystemDAD-500 HAF-502 HAF-505 HAR-507
AIR DRYING CENTRIFUGAL COALESCER REGULATORDESICCANT SYSTEM UNITS SYSTEM* FILTER ONLY FILTER ONLY** ONLY
Air Inlet 1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F) 3/8" NPT (F)Air Outlet 1/2" NPT (F) 1/2" NPT (F)1/2" NPT (F) 1/4" NPT (F)(3 ea)Max. Operating Pressure (psi) 150 150 150 150Replacement Filters/Desiccant DAD-1 HAF-6 HAF-28 —Service Bulletin SB-6-156 SB-6-146 SB-6-152 SB-6-147Air Flow Capacity (cfm) 25 100 55 60
DAD-500Service BulletinSB-6-156-J
* Includes HAF-502, HAF-505 and HAR-506.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted36
Clean Air Filtration-Accessories
HAF-507-K12 WhirlWind In-Line FilterMAXIMUM
HOUSING OPERATING OPERATING PRESSURE DROP LIQUID SERVICEMATERIAL PACKAGING THREADS PRESSURE TEMPERATURES @ 80 PSI w/ 20 SCFMCONTAMINANT BULLETIN
Solvent-resistant 12 filters 1/4" NSP (M) inlet 125 psi 50oF - 110oF 2 psi 1.5 fl. oz. SI-8-10-1Delrin® plastic per dispenser carton 1/4" NSP (F) inlet
MAX. REGULATED MAX AIR MAXCAPACITY PRESS.RANGE INLET PRESS. OPERATING DIMENSIONS WEIGHT MAIN AIR INLET MAIN LINE OUTLET REGULATED OUTLETS
MODEL CFM PSI PSI TEMP OF H" X W" LBS. PORT SIZE PORT SIZE PORT SIZE
HAR-501* 15 0 - 20 250 120o 6 x 4-1/2 2-1/4 1 3/8" NPT (F) - - 1 3/8" NPT (F)HAR-502 40 0 - 125 250 120o 4-7/8 x 2 3/8 1-1/8 1 1/4” NPT (F) 1 1/7” NPT (F) 2 1/4” NPT (F)HAR-505 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 1-4” NPT (F) - - 3 1/4”NPT (F)HAR-535 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 1 1/4" NPT (F) 1 3/8" NPT (F)HAR-555 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 2,4 1/4" NPT (F) 1 1/2" NPT (F)HAR-507 60 0 - 125 250 150o 4-7/8 x 3 1-1/2 1 3/8" NPT (F) - - 3 1/4" NPT (F)
WhirlWind In-Line Filter
The WhirlWind disposable in-linefilter attaches to the base of the spraygun or air tool to remove anyremaining water, oil, dirt and rustfrom the air line. This high-quality,high-flow, solvent-resistant air filterhas a very low pressure drop and hasa floating filter that automaticallyadjusts for changing air conditions.
• Air is swirled to trap droplets, thenfiltered to absorb remainingparticulates.
• Multilayer design extends life, so unitlasts up to 40% longer than other filters.
• Perfect for use with HVLP guns,WhirlWind provides 55% more air flowthan other filters.
HAF-507-K12
CleanAir Air RegulatorsHAR-502/505/535/555
Air RegulatorGeneral purpose regulators for line
takeoff use or as integral regulators onpumps, pressure tanks and other airoperated devices. Require separate trapor filter in air line to remove moistureor dirt.
• Unique three position, non-risingadjusting knob.
• Removable plug and cap.
• All metal body; durable Delrin® capand knob; Buna N diaphragm anddisc.
• Accurate regulator mechanismprovides precision air control.
• Self-relieving design.
• Both main line and regulated outletsavailable from same units.
HAR-501 Air RegulatorExtra Sensitive regulator for use
with precision control on pressure feedtanks or other dead-end applications.Can be used to control atomizationpressure for one spray gun.
• Self-relieving regulator.
• Tough, reinforced Buna N
diaphragm for extended service life.
• 100 mesh stainless steel strainer.
• Removable bottom plug for easyservice.
• Forged brass body and stainless steelor brass internal parts for longservice.
• High ratio of diaphragm surface toorifice area provides stable uniformregulation.
* Extra-sensitive regulator for precise control on pressure tanks and other dead-end applications.** These models include nickel for corrosion protection. Other models are painted.
TM
HAR-505 HAR-501
37
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
Air Control Accessories
For accurate pressure readings,standard gauges are made fromrust-resistant materials and includeglass covered dials. Can be used inany location where conditions ofvibration or rough service exist.
GA-77 gauge is very accurate in lowpressure range and ideal for criticalpressure adjustments. Calibrated inounces from 0 to 10 lbs.; in poundsfrom 10 to 30 lbs.
GA Pressure GaugesMODEL SCALE (TYPE) THREAD DIAMETER INLET
GA-73 0 - 30 psi (A, F) 1/4" NPT (M) 2" BottomGA-77 0 - 30 psi (A, F) 1/4" NPT (M) 3-1/2" BottomGA-288 0 - 160 psi (A, F) 1/4" NPT (M) 2" BottomGA-313 0 - 15 psi (A) 1/8" NPT (M) 1-1/2" BottomGA-316 0 - 160 psi (A) 1/4" NPT (M) 2" BackGA-333 0 - 100 psi (A, F) 1/4" NPT (M) 2" BottomGA-338 0 - 160 psi (A) 1/8" NPT (M) 1-1/2" Back
• HARG-510 is a precise, lightweightair regulator and gauge combination.Fits any professional spray gun;comfortable for left and right-handedpainters. Swivel adaptor allows fastinstallation, and a lock-ring securespressure settings to avoid interruptionsfor readjustments. Max. Air InletPressure: 400 psiOutlet Pressure Adjust. Range:5-100 psiGauge Port Size in Regulator:1/8" NPT (F)
• HAV-500 and HAV-501 are preciseair adjustment valves that controlpressure at the spray gun. Fits allprofessional spray guns. A swivel topallows for easy and fast installation.
• P-H-5516 air adjustment accessoryattaches directly to the spray gunair inlet. The large knurled knobadjusts air flow. Commonly used withspray guns, pressure tanks and pumps.
Air Adjusting ValvesGAUGE
MODEL AIR INLET AIR OUTLET NET WT. RANGE TYPE
HARG-510 1/4" NPS (M) 1/4" NPS (F) 10 oz. 0 - 160 psi Diaphragm(Nipple) (Swivel Adapter) Relieving
HAV-500 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3.5 oz. n/a StraightHAV-501 1/4" NPS (M) 1/4" NPS (F) (Swivel) 5 oz. 0 - 160 psi w/ GaugeP-H-5516 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3 oz. n/a Straight
Air ValvesMAX. OPERATING
MODEL DESCRIPTION PRESSURE MATERIAL
VA-527 3/8" NPS (M) x 3/8" NPT (M) 500 Stainless SteelVA-528 3/8” NPS (M) x 3/8” NPT (F) 500 Stainless SteelVA-540 3/8" NPS (M) x 3/8" NPT (M) 500 BrassVA-541 1/4" NPS (M) x 3/8" NPT (M) 500 BrassVA-542 1/4" NPS (M) x 1/4" NPT (M) 500 Brass
HARG-510Service Bulletin - SB-6-105-D
HAV-501 HAV-500 P-H-5516
Air Regulator Lockout - HAR-400This device allows the painter to est their air
regulators to guarantee proper atomization, as wellas to assure compliance in areas where air cappressure is limited to 10 PSI or less. Includes onekey per unit.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted38
Clean Air Filtration-Accessories
Air VizorTM
Breathable Air Systems
The World’s Most Technologically AdvancedAir Supplied Respirator.
• Protects against isocyanate exposure.• Part of a complete breathable air system.*• NIOSH approved (TC 19C-0365) - meets OSHA
requirements.• Cool and comfortable.• Full lightweight face mask with excellent visibility.
- Ratchet adjustable headgear.- Visor window improved to reduce glare- Detachable hair and neck cover- Rigid face piece for better visibility over time.- Replaceable visor window and detachable fabric
face shield for economical servicing.• Easily accommodates prescription eyewear and bearded
employees.• Disposable carbon filter and pre-set tamper proof
regulator.- 1,000 hour carbon cartridge life
• Adjustable belt with quick fit buckle.• Quick connect between visor and waistbelt permits easy
removal of visor.• Air Vizor (MPV-625) includes:
- Full face mask- Belt-mounted filter and regulator- Breathing air tube
* Air VizorTM requires proper air line filtration and carbonmonoxide (CO) monitoring to complete an approvedsupplied air respirator. See next page for proper air linefiltration. A carbon monoxide (CO) monitor may bepurchased locally or from ENMET Corporation: (734)761-1270 (phone). Order form F-1073-B available fromDeVilbiss upon request.
Breathable Air Systems
Belt # ofRegulator Breathable Visor Filtration
Order No. and Hood Air Covers Unit FiltrationModel No. Assembly Hose (30’) Included Included Description
Yes No 2 None --------MPV-625
Yes Yes 12 DAD-504 DesiccantMPV-650 Retrofit
System
Yes Yes 12 DAD-503 3-StageMPV-651 Filtration
with DesiccantAir Dryer System
Yes Yes 12 HAF-601 3-StageMPV-652 Filtration
System
39
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
Air VizorTM
Breathable Air Filtration Units
DAD-503
• Converts shop air into clean, dry,
contaminant-free air for breathingsystems and spray operations.
• 5 micron particulate filter (Stage 1)
• .01 micron coalescing filter (Stage 2)• Charcoal filter for hydrocarbon and odor removal
(Stage 3)
• 28 CFM breathing air regulator• Desiccant system removes water vapor for spray
gun (rated for 25 CFM maximum flow)
• 60 CFM spray gun regulator• Automatic drains (Stages 1, 2 and 3)
• Can be used with up to four Air Visors
• 1/2” NPT inlet• Refer to Service Bulletin (SB-6-159
HAF-601
• Converts shop air into clean, contaminant-free air
for breathing systems and spray operations• 5 micron particulate filter (Stage 1)
• .01 micron coalescing filter (Stage 2)
• Charcoal filter for hydrocarbon and odor removal(Stage 3)
• 28 CFM breathing air regulator
• 60 CFM spray gun regulator• Automatic drains (Stages 1, 2 and 3)
• Wall-mount bracket
• Can be used with up to four Air Vizors• 1/2” NPT inlet
• Refer to Service Bulletin SB-6-132
DAD-504
• Converts a DAD-500 into a breathing air source• Charcoal filter for hydrocarbon and odor removal
• 28 CFM breathing air regulator. Includes all
necessary fittings• Can be used with one Air Vizor
• Automatic drain
• Refer to Service Bulletin SB-6-176