izi-link dmx interface - tde lighttech · the izi-link manager and izi-link network are connected...
TRANSCRIPT
![Page 1: IZI-Link DMX Interface - TDE Lighttech · The IZI-Link manager and IZI-Link network are connected through the USB to IZI-Link programmer. The USB to IZI-Link programmer cable needs](https://reader036.vdocuments.net/reader036/viewer/2022062318/6042dc39e1e2717fa57bf271/html5/thumbnails/1.jpg)
Technical specifications
Features
Power Input voltage: 48VDC
Output voltage: 48VDC (IZI-Link) Output power: Max. 480W Current output: Max. 10A
Control Control in/out: DMX-512 / 1990 galvanically isolated
Dry contact input: 4 galvanically isolated
Miscellaneous Housing: DIN-rail (4 module width)
Input connector: Print connector Screw terminal power connections: Max. 2,5mm² Screw terminal DMX-512: Max. 1,5mm² Screw terminal dry contacts: Max. 1,5mm²
www.tde-lighttech.nl
IZI-Link DMX Interfaceilluminating creativityTDE-lighttech
The IZI-Link DMX interface is needed to setup an IZI-Link system. An IZI-Link system utilises powerline communication to transmit data over a low power voltage network, allowing you to control, monitor and configure each IZI-Link enabled product.This technique eliminates additional control wiring to IZI-Link enabledLED-spots and LED-drivers which make the installation more reliableand easy to install. The IZI-Link system can easily be scaled into a larger network by adding IZI-Link interfaces.
The IZI-Link DMX Interface is controllable through DMX-512 and has 4 additional galvanically isolated contact inputs to override DMX-control for use as emergency contacts or local control switches.
Simple installation2 Wire cable for power and data
High power480 Watt
CommisioningRemote configuring
Emergency contactSystem override contact inputs
![Page 2: IZI-Link DMX Interface - TDE Lighttech · The IZI-Link manager and IZI-Link network are connected through the USB to IZI-Link programmer. The USB to IZI-Link programmer cable needs](https://reader036.vdocuments.net/reader036/viewer/2022062318/6042dc39e1e2717fa57bf271/html5/thumbnails/2.jpg)
Order CodeOrder Code
www.tde-lighttech.nl
illuminating creativityTDE-lighttech
IZI.IF.DMX - IZI-Link DMX inferface; 48VDC; Max 10A; Din railCAB.USB.IZI-LINK - USB to IZI-link programmer cable
90mm
71mm
Dimensions
58mm
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
System overview
DMX512 DMX512
CONTACT
IN OUT
48VIN
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
LED Driver
LED Driver
A simple overview of an IZI-Link system is shown below. An IZI-Link system is easily scalable, the below shows only a basic system, countless other configurations are possible.
IZI-Link DMX Interface
Use min 90ºC supply conductors when connecting to the IZI-LINK DMX interface
Only use power supplies which can deliver a constant dc-voltage of 48VDC
Wiring
![Page 3: IZI-Link DMX Interface - TDE Lighttech · The IZI-Link manager and IZI-Link network are connected through the USB to IZI-Link programmer. The USB to IZI-Link programmer cable needs](https://reader036.vdocuments.net/reader036/viewer/2022062318/6042dc39e1e2717fa57bf271/html5/thumbnails/3.jpg)
LED indication
www.tde-lighttech.nl
illuminating creativityTDE-lighttech
Wiring diagram
IZI-Link DMX Interface
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
DMX Input
1
2
3
0VD-D+
1
2
3
0VD-D+
DMX Output
48VDC+GROUND
+
- IZI-Link output
123
Contact closure
4
-
Status LED Behaviour
Power ok, No data Red On
Green Blink
Power ok, Data reception
Red Off
Green Blink
Protect mode Red Blink
Green -
Identify/Test mode Red Toggle
Green Toggle
Identify mode The Identify mode on the IZI-manager allows identification of each individual fixture/interface.
Test mode When in test mode, the DMX interface sends out value 255 (100%) to all channels on the IZI-Link Master DMX interface.
Protect mode The IZI-link DMX interface will go into protect mode when either, too many load is detected or a power surge has occurred.
![Page 4: IZI-Link DMX Interface - TDE Lighttech · The IZI-Link manager and IZI-Link network are connected through the USB to IZI-Link programmer. The USB to IZI-Link programmer cable needs](https://reader036.vdocuments.net/reader036/viewer/2022062318/6042dc39e1e2717fa57bf271/html5/thumbnails/4.jpg)
illuminating creativityTDE-lighttech
Commisioning
All products need to be powered and connected to an IZI-Link DMX interface, DMX splitter or directly on the DMX input of a fixture in order for any configurations can be made.
The IZI-Link manager and IZI-Link network are connected through the USB to IZI-Link programmer.
The USB to IZI-Link programmer cable needs to be connected to a computer and the DMX512 input of either the IZI-Link Master DMX interface, Splitter or directly on the fixture. When multiple IZI-Link products are connected together make sure to connect to the first IZI-link driver.
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
MASTER DMX INTERFACE
POWERDMX OK
GND GNDD- D-D+ D+REF REF
DMX512
CONTACT CLOSURE INPUT
Optical isolated Optical isolated
U-in: 48 VDCI-in: 10 A max
POWER INPUT OUTPUT
POWER
V- V+ 2 1 +INPUT OUTPUT
INPUT OUTPUT
PROGRAM SWITCH
Please refer to manual for more information
U-out: 48 VDCI-out: 10 A max
OUTPUTSLAVE
S -
RoHS 75
INDOOR
www.tde-lighttech.com
- 2 3 41
Single IZI-Link driver Multiple IZI-Link drivers
IZI-Link DMX Interface
www.tde-lighttech.nl