Designed for replacement of shower drains where the work space is restricted by building members or existing pipe.Unique design incorporates four ‘jacking bolts’ and a pressure plate washer to create a seal.Internal gasket wrench is included for tightening the internal compression nut.Can be used with 2″ Sch. 40 ABS or PVC and no-hubor extra-heavy cast iron DWV pipe.

•

•

•

•

JackRabbit™

Jacking Bolt Shower Drain

Standard Shower DrainInstallation is diffi cult using awrench on a standard locknut.

JackRabbit Shower DrainInstallation is easy using a

screwdriver on jacking bolts.

Installation in Tight Spaces

2″ Sch. 40 pipe

2 ⅛″

4 ¼″REPLACEMENT STRAINERS

Antique Brass White Enamel

Oil-Rubbed Bronze Satin Copper

Stainless Steel

Pearl Nickel Satin Nickel

Polished Brass

Replacement Strainers • 18 gauge stainless steel • 4 ¼″ diameter • 3 ¼ in² free area • 2 5 ⁄8″ screw centers (2 screws)

Snap-In Screw-On

Item No. Description Min. Qty.

Case Qty.

JACKRABBIT SHOWER DRAINBULK

827-2J 2″ brass jacking bolt shower drain with SS strainer 1 20CLAMSHELL IN CUT CASE

827-2JPK 2″ brass jacking bolt shower drain with SS strainer 1 6

SNAP-IN STRAINERS – FITS 821, 825, 827, 828, 829 & 840 SERIES*

827-2S Stainless steel 1 1

827-2SP PVD polished brass fi nish 1 1

827-2SZ Pearl nickel fi nish 1 1

827-2SN Satin nickel fi nish 1 1

827-2RB Oil-rubbed bronze fi nish 1 1

827-2SC Satin copper fi nish 1 1

827-2AB Antique brass fi nish 1 1

827-2SW White enamel fi nish 1 1SCREW-ON STRAINERS – FITS 821, 825 & 840 SERIES*

821-2S Stainless steel 1 1

821-2SP PVD polished brass fi nish 1 1

821-2SZ Pearl nickel fi nish 1 1

825-2SN Satin nickel fi nish 1 1

821-2RB Oil-rubbed bronze fi nish 1 1

825-2SC Satin copper fi nish 1 1

825-2AB Antique brass fi nish 1 1

821-2SW White enamel fi nish 1 1

* Except for 825-2PFS

tel: 1-800-821-3944fax: 1-800-758-5950www.siouxchief.comP.O. Box 39724110 South Peculiar DrivePeculiar, Missouri 64078 U.S.A.

Shower Pan DrainSnap-in 18 Gauge Strainer – Plastic Rim

with Machine Screws & Brass Inserts

For more information on our full line of shower drains see our catalog.

JACKRABBIT BROCHURE 9/05 v1 © 2005 SIOUX CHIEF MFG.

More Innovative Sioux Chief Shower Drains

Shower Pan DrainCast Metal Ring & Strainer

with Machine Screws & Brass Inserts

Solvent WeldScrew-on 18 Gauge Strainer

ComboNo-Caulk Gasket or Solvent Weld

Snap-In 18 Gauge Strainer

Brass No-CaulkSnap-in 18 Gauge Strainer

From ABOVE The Shower Floor

1. Remove existing shower drain and replace drain pipe as needed. Pipe should terminate just below the underside of the shower module fl oor. Clean the shower module fl oor where the old drain was, removing old putty, silicone, debris, etc.

2. Unscrew and remove locknut, pressure plate washer, friction washer and sealing washer, remove strainer and internal wrench (black plastic) from drain.

3. Loosen compression nut if necessary, and apply a bead of silicone or apply plumber’s putty around the underside of drain body fl ange as shown or use our No-Putty Gasket (290-20320). Push the drain body over the pipe, taking care not to wrinkle or damage the compression gasket, until the drain is pressed fi rmly down against the shower module fl oor.

4. Tighten compression nut with plastic wrench provided. Remove the plastic wrench and keep it for future use.

From BELOW The Shower Floor

5. Thread jacking bolts so that ¼″ is exposed above the locknut.

6. Place sealing washer, then friction washer, then pressure plate washer (with fl at surface up), in that order, up over the threaded drain body. Be sure there are no obstructions, and that the sealing washer makes clean, even contact with the bottom of the shower module fl oor. Engage the locknut and hand tighten up against washer stack.

7. Tighten jacking bolts in order shown, getting tighter each time through the sequence until each bolt is completely tightened. Clean off any residual silicone from the shower module fl oor.

8. Check for leaks after silicone has dried (No-Putty Gasket can be tested immediately after installation). Turn water on in shower, and from below shower fl oor, check the drain area for leaks concentrating on the area between pipe and compressiongasket [A] and between shower module fl oor and sealing washer [B].If a leak occurs in area A, use the black plastic wrench (from step 4) to tighten the compression nut. If a leak occurs in area B, tighten jacking bolts using the same method described in step 7.

9. When the installation is complete, remove the adhesive cover from the strainer and install in to drain.

Ensure clean, even contact

5

6

AB

7

Peel off cover9

Solvent WeldSnap-in 18 Gauge Strainer

No-CaulkSnap-in 18 Gauge Strainer

OffsetScrew-on 18 Gauge

1 Shower module fl oor

Clean where olddrain was removed

2″ Sch. 40 pipe

Subfl oor

Tighten compression nut

Compression gasket

Compression nut

4

Silicone,plumber’sputty or gasket

3

Strainer

Internal wrench

Drain body

Sealing washerFriction washerPressure plate washer

Locknut with jacking bolts

2

821-200PNR

821-270P825-2P

825-27P

826-2P

828-2

827-2B

825-2PFS

JackRabbit Installation Instructions