#JF509 Beaded Easter Egg 6 1/2” Tall x 6” Wide

Materials Included in Kit: 132—6mm Faceted Beads—Dark Amethyst 88—8mm Faceted Beads—Dark Amethyst 396—10mm Star Beads—Amethyst 352—18mm Star Beads—Pink 176—18mm Star Beads—Amethyst 44—#2 Safety Pins—Silver 66—#3 Safety Pins—Silver 96” - 20 Gauge Wire—Silver 1—String Lights—Clear Materials Needed: Wire Cutters Ruler

Directions Creating Pins: To add beads to the safety pins, hold one opened safety pin with the point facing away and up. Add beads as shown in the table at the bottom. Begin putting beads on the pin, starting with the beads listed on the bottom and working your way to the head of the pin. PLEASE NOTE: Beads should appear in the same order as shown below. (Make sure to create the number of pins needed of each type, & keep pins separate. 110 Pins Total.) Step 1: Cut your wire into 2—12” and 4—18” pieces.

See Diagram on last page

for wiring pins. Row 1: Star ting at the bottom of the egg. Using a 12” piece of wire, * thread wire through the head of 1- “A” Pin, add 1– 6mm Faceted Bead (Dark Amethyst). Repeat from * until 22- “A” Pins and 22—6mm Faceted Beads (Dark Amethyst) have been used. Pull wire tight. Twist and cut off excess wire. Row 2: Using a 18” piece of wire, * thread wire through the bottom loop of 1- “A” Pin from the previous row, add 1—6mm Faceted Bead (Dark Amethyst). Then thread wire through the head pin of 1- “B” Pin, add 1—6mm Faceted Bead (Dark Amethyst). Repeat from * until 22- “B” Pins and 44—6mm Faceted Beads (Dark Amethyst have been used. Pull wire tight. Twist and cut off excess wire. Copyright ©2003 Bolek’s Craft Supplys, Inc. all rights reserved

“B” Pin (#3) (Make 44)

8—18mm Star Beads (Pink)

“A” Pin (#2) (Make 44)

9—10mm Star Beads (Amethyst)

“C” Pin (#3) (Make 22)

8—18mm Star Beads (Amethyst)

1

#JF509 Beaded Easter Egg Row 3: Using a 18” piece of wire, * thread wire through the bottom loop of 1- “B” Pin from the previous row, add 1—8mm Faceted Bead (Dark Amethyst). Then thread wire through the head of 1- “C” Pin, add 1—8mm Faceted Bead. Repeat from * until 22- “C” Pins and 44—8mm Faceted Beads have been used. Pull wire tight. Twist and cut off excess wire. Row 4: Using a 18” piece of wire, * thread wire through the bottom loop of 1- “C” Pin from the previous row, add 1—8mm Faceted Bead (Dark Amethyst). Then thread wire through the head of 1- “B” Pin, add 1—8mm Faceted Bead (Dark Amethyst). Repeat from * until 22- “B” Pins and 44—8mm Faceted Beads (Dark Amethyst) have been used. Pull wire tight. Twist and cut off excess wire. Row 5: Using a 18” piece of wire, * thread wire through the bottom loop of 1- “B” Pin from the previous row, add 1—6mm Faceted Bead (Dark Amethyst). Then thread wire through the head of 1- “A” Pin, add 1—6mm Faceted Bead (Dark Amethyst). Repeat from * until 22- “A” Pins and 44—6mm Faceted Beads have been used. Pull wire tight. Twist and cut off excess wire. Row 6: Using a 12” piece of wire, * thread wire through the bottom loop of 1- “A” Pin from the previous row, add 1—6mm Faceted Bead (Dark Amethyst). Repeat from * until 22—6mm Faceted Beads (Dark Ame-thyst) have been used. Pull wire tight. Twist and cut off excess wire. Step 2: Add lights. You have completed your Beaded Easter Egg. Copyright ©2003 Bolek’s Craft Supplys, Inc. all rights reserved

2

#JF509 Beaded Easter Egg

Copyright ©2003 Bolek’s Craft Supplys, Inc. all rights reserved

“A” Pin “A” Pin

“B” Pin

“C” Pin “C” Pin

“B” Pin

“A” Pin

“B” Pin

“A” Pin “A” Pin

Row 1

Row 2

Row 3

Row 4

Row 5

Row 6

3