jpr-installation-guide-flutes-lydian-array-remote · flutes lydian array remote installation guide...

7
62 IN 48 IN FLUTES LYDIAN ARRAY Remote Installation Guide SHOWN ARE EXAMPLES OF CONFIGURATION POSSIBILITIES. SPECIFIC FIXTURE CONFIGURATION MAY VARY. 1

Upload: others

Post on 18-Oct-2020

7 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

62 IN

48 IN

FLUTES LYDIAN ARRAYRemote Installation Guide

SHOWN ARE EXAMPLES OF CONFIGURATION POSSIBILITIES. SPECIFIC FIXTURE CONFIGURATION MAY VARY.

1

Page 2: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

WARNING

A LICENSED ELECTRICIAN SHOULD PERFORM INSTALLATION IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC) AND RELEVANT LOCAL CODES.

DISCONNECT MAIN POWER AT THE SOURCE PRIOR TO INSTALLATION.

INSTRUCTIONS MEANT FOR A REMOTE CLASS 2 DRIVER.

FIGURE 1A

FIGURE 1

FIGURE 1A

FIGURE 1A

End cap

Slide sections into each other to connect

Module

FIGURE 1C

FIGURE 1B

Quick-disconnect

FIGURE 1C

M4 Screw

Locking washer

STEP 1: JOINING FIXTURE SECTIONS

Remove the end caps from modules as shown in figure 1A by pulling them off.A.Connect the sections using the dovetail feature in the modules as shown in figure 1A.B.Connect the quick-disconnect switch between the two sections of the fixture as shown in figure 1B.C.Secure the sections of the fixture together using provided M4 screw and locking washer as shown in figure 1C.D.Reinstall the caps on the modules.E.

The two sections of the fixture can be joined following the instruction below as seen in illustrations above.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 2

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489

Page 3: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

JUNCTION BOX MOUNTED

FOR FIXTURES WIRED TO A JUNCTION BOX.

SEE STEP 3A FOR DETAILED INSTALLATION AND WIRING INFORMATION.

FIGURE 3

CEILING MOUNTED

FOR FIXTURE MOUNTED DIRECTLY TOTHE CEILING.

SEE STEP 3B FOR DETAILED INSTALLATION AND WIRING INFORMATIONBLOCKING IS RECOMMENDED FOR DRYWALL MOUNTING.

FIGURE 4

47 12 "OR

19 34 "OR

8""

34 34 "

62 12 "

115

" MAX

FIGURE 2

A B

POWER FEED OPTIONS

STEP 2: MARK MOUNTING POINTS

POWERED CANOPY IS USED TO SUSPEND AND POWER THE FIXTURE (SEE POWER FEED OPTIONS).

NON-POWERED CANOPY IS USED TO SUSPEND THE FIXTURE.

KEY

A

B

Carefully mark the mounting points with a pencil or marker, using the spacing in Figure 1. It is highly recommended to use a laser alignment/ measuring tool to ensure that mounting parts are properly distanced and fall on a straight line.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 3

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489

Page 4: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

A

Cover plate

Set screw

CanopyFIGURE 5

A

1/8" IPS nut

1/8" IPS nut

1/8" IPS x 1" length threaded nipple

Top cap

FIGURE 6

Crossbar

WasherWood screw

Top capCover plate

B

Set screw

Canopy

B

Top cap

Press the safety nut upwards and hold to pass aircraft cable through the gripper

A B

Bottom cap

Power cordfrom fixtureCanopy

A

Set screw

Cap screw

3 4

Loosen cap screw in bottom cap to release the bottom cap. Pass power cord from fixture through the cap and canopy as shown. Adjust the length of power cord to adjust fixture's drop height. Tighten set screw after adjusting power cord length. Attach bottom cap by tightening the cap screw.Make sure bottom cap and canopy are aligned properly before securing cap screw.

STEP 3A: JUNCTION BOX COVER PLATE INSTALLATION INSTRUCTIONS

Remove set screws from canopy to release top cap.

1 2

Attach the crossbar to the junction box using provided screws.

Using provided wood screw and washer, connect the top cap and provided cover plate to ceiling. Wood screws are provided for default installation. Alternate screws may be used at the recommendation of an electrician. Blocking is recommended for drywall mounting.

Partly loosen safety nut on cable gripper. Feed aircraft cables through the grippers as shown above. Keep the safety nut on gripper pressed to pass aircraft cable through the gripper. Release the safety nut to hold the aircraft cable in position. Do not cut extra power and aircraft cables until desired suspension height is achieved. Tighten the safety nut after completing adjustment.

5

FIGURE 7

FIGURE 9

FIGURE 8

Remove set screws from canopy to release top cap. Install cover plate on the top cap as shown.

Pass low voltage wires from junction box through cross bar and through 1/8IPS nipple attached to cover plate as shown. Screw 1/8IPS nipple into the crossbar to connect cover plate to crossbar.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 4

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489

Page 5: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

Set screw

B

BA

Set screw

FIGURE 11

A

Low voltage wires from LED driver

REMOTE LED

DRIVER

OU

TPU

TAC - NEUTRAL

AC - LINEIN

PUT

N

L

-

+

+ 24VDC lead from remote driver

White lead (+)from fixture

Silver Shielding (-) from fixture

- 24VDC lead from remote driver

FIGURE 10

A

FIGURE 12

Adjust power and aircraft cable length as needed to adjust the drop height and to level the fixture. Tighten the safety nut after completing adjustment.

6 7

Connect wires according to diagram (wire nuts provided). Wires to and from the driver are not included.

8

Use set screws (removed in first instruction) to connect canopy to top cap.

Push wires inside the canopy and use set screws (removed in first instruction) to connect canopy to cover plate.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 5

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489

Page 6: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

Wires from remote driver

Washer

Wood screw

Top capA

FIGURE 14

Top cap

Set screw

Canopy

Press the safety nut upwards and hold to pass aircraft cable through the gripper

A B

Washer

Wood screw

Top capB

Bottom cap

Power cordfrom fixture

Canopy

A

Set screw

Cap screw

Cover plate

Set screw

CanopyA

1/8" IPS nut

1/8" IPS nut

1/8" IPS x 1" length threaded nipple

Top cap

1 2

3

4

STEP 3B: CEILING MOUNTING INSTALLATION INSTRUCTIONS

Loosen cap screw in bottom cap to release the bottom cap. Pass power cord from fixture through the cap and canopy as shown. Adjust the length of power cord to adjust fixture's drop height. Tighten set screw after adjusting power cord length. Attach bottom cap by tightening the cap screw.Do not cut extra power cable before making sure the its length is suitable for fixture's drop height.Make sure bottom cap and canopy are aligned properly before securing cap screw.

FIGURE 16

Remove set screws from canopies to release top cap.

FIGURE 13Pass low voltage wires from the remote driver through the A.smaller hole in the top cap. Using provided wood screw and washer, connect the top cap to ceiling.Using provided wood screw and washer, connect the top cap B.to ceiling.

Wood screws are provided for default installation. Alternate screws may be used at the recommendation of an electrician. Blocking may be required.

FIGURE 15

Partly loosen safety nut on cable gripper. Feed aircraft cables through the grippers as shown above. Keep the safety nut on gripper pressed to pass aircraft cable through the gripper. Release the safety nut to hold the aircraft cable in position. Do not cut extra power and aircraft cables until desired suspension height is achieved. Tighten the safety nut after completing adjustment.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 6

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489

Page 7: JPR-Installation-Guide-Flutes-Lydian-Array-Remote · flutes lydian array remote installation guide shown are examples of configuration possibilities. specific fixture configuration

CARE INSTRUCTIONS

Gently wipe with a damp cloth to remove dirt, dust, and fingerprints.

Do not use any chemical cleaning solution.

Use indoors only.

Low voltage wires from LED driverREMOTE

LED DRIVER

OU

TPU

T

AC - NEUTRAL

AC - LINEIN

PUT

N

L

-

+

+ 24VDC lead from remote driver

White lead (+)from fixture

Silver Shielding (-) from fixture

- 24VDC lead from remote driver

Connect wires according to diagram (wire nuts provided). Wires to and from the driver are not included.

FIGURE 17

A

Set screw

A

FIGURE 19

BA

Set screw

B

6

7

FIGURE 18

Adjust power and aircraft cable length as needed to adjust the drop height and to level the fixture. Tighten the safety nut after completing adjustment.

5

Push wires inside the canopy and use set screws (removed in first instruction) to connect canopy to cover plate.

Use set screws (removed in first instruction) to connect canopy to top cap.

FLUTES LYDIAN ARRAY INSTALLATION GUIDE 7

WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489