juanita e. thornton shepherd park neighborhood library ... · juanita e. thornton | shepherd park...

JUANITA E. THORNTON | SHEPHERD PARK NEIGHBORHOOD LIBRARYLIMITED RENOVATION

7420 GEORGIA AVENUE NWWASHINGTON, DC 20012

BID SET01/22/2015

The Georgetown Design Group, Inc.1920 N Street, NW Suite 100

Washington, DC 20036t. 202.857.0060 | f. 202.857.0089

www.gdgdesignbuild.comGDG

Geo

rgia

Ave

nue

NW

Juniper Street NW

Hemlock Street NW

Geranium Street NW

Fern Street NW

Elder Street NW

Shepherd Road NW

12th

Stre

et N

W

8th

Stre

et N

W

13th

Stre

et N

W

Bla

ir R

oad

NW

Alaska

Ave

nue N

W

Fern Street NW

Geranium Street NW

Hemlock Street NW

Holly Street NW

7420 GeorgiaAve NW

Walter Reed Medical Center

TABLE OF CONTENTS:

G1 General NotesG2 General SpecificationsDB Basement Demo PlanD1 1st Floor Demo PlanD2 2nd Floor Demo PlanAB Basement Renovation PlanA1 1st Floor Renovation Plan and SchedulesA2 2nd Floor Renovation PlanA3 Architectural DetailsA4 Millwork DetailsA5 Millwork DetailsA6 Millwork DetailsA7 Millwork DetailsA8 Millwork DetailsA9 Roof PlanE1 Existing 1st Floor ElectricalE2 Existing 2nd Floor ElectricalE3 New 1st Floor ElectricalE4 New 2nd Floor ElectricalM1 1st Floor MechanicalM2 2nd Floor MechanicalID1 1st Floor Furniture Plan (NIC)ID2 2nd Floor Furniture Plan (NIC)

PROJECT INFORMATION:Non-structuralInterior Improvements

7420 Georgia Avenue, NWWashington, DC 20012

Lot 42, Square 2956

18,888 Sq. Ft. +/-

C-2-A

11,244 Sq. Ft. Existing11,244 Sq. Ft. No Change23,095 Sq. Ft. Existing23,095 Sq. Ft. No Change

Assembly A-3

2A-Existing Library

Existing Automatic Sprinkler SystemThroughout the Building

SCOPE OF WORK:

ADDRESS:

LOT & SQUARE:

LOT AREA:

ZONING:

EXIST. BLDG FOOTPRINT:PROPOSED BLDG FOOTPRINT:EXISTING TOTAL SF:PROPOSED TOTAL SF:

USE GROUP:

Construction Type:

Fire Protection:

ALL WORK TO BE PERFORMED IN ACCORDANCE WITHIBC 2012, APPLICABLE DC BUILDING CODE SUPPLEMENT,

AND FEDERAL REGULATIONS.

ARCHITECT: Mokhless Al-Hariri, R.A., AIA

STRUCTURAL ENGINEER: Frank Chow, P.E.

MEP ENGINEER: George I. Worsley, P.E.

G1

1920 N STREET, N.W.SUITE 100

WASHINGTON, DC 20036

TEL: (202) 857-0060FAX: (202) 857-0089

www.gdgdesignbuild.com

Revisions:

Scale: 18" = 1'

Sheet Title: General Notes

JUANITA E.THORNTON

SHEPHERD PARKNEIGHBORHOOD

LIBRARYRENOVATION

7420 GEORGIA AVE NWWASHINGTON, DC

20012

GDGGDGDESIGN BUILD

THE GEORGETOWN DESIGN GROUP, INC.

DIVISION 4 MASONRY AND STONE WORK1. ALL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST STANDARDS.

2. ALL MASONRY WORK SHALL MATCH EXISTING WORK AND SHALL BE EXECUTED IN ACCORDANCE WITH THE PROJECT'SREQUIREMENTS AND HIGHEST APPLICABLE TRADE SPECIFICATIONS.

3. NEW MORTAR JOINTS COMPOSITION, COLOR, WIDTH, AND DEPTH SHALL BE SET TO MATCH EXISTING WORK.

4. WATERPROOFING AS WELL AS VERTICAL AND HORIZONTAL ANCHORS SHALL BE PROVIDED IN ACCORDANCE WITH THE HIGHESTSTANDARDS OF THE TRADE.

DIVISION 5 METALS1. ALL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST STANDARDS.

2. ALL STRUCTURAL AND MISCELLANEOUS STEEL WORK SHALL BE EXECUTED IN ACCORDANCE WITH THE PROJECT'SREQUIREMENTS AND HIGHEST APPLICABLE STANDARD SPECIFICATIONS.

3. CONTRACTOR SHALL FIELD-VERIFY ALL DIMENSIONS AND SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG, TRIPLICATECOPIES OF STEEL SHOP DRAWINGS.

DIVISION 6 WOOD AND PLASTICS1. THE SCOPE OF WORK INCLUDES ALL STRUCTURAL WOOD MEMBERS, ROUGH CARPENTRY AND BLOCKING WORK, AS WELL AS ALL

FINISHED CARPENTRY WORK AND MILLWORK SHOWN ON THE DRAWINGS.

2. CONTRACTOR SHALL FIELD-VERIFY ALL DIMENSIONS AND SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG, TRIPLICATECOPIES OF THE MILLWORK SHOP DRAWINGS.

3. THE SCOPE OF WORK INCLUDES THE PROPER ASSEMBLY AND INSTALLATION OF ALL RELOCATED, MODIFIED, OR NEW SHELVINGPANELS, CABINETS, COUNTERTOPS, ETC.

4. ALL WORK SHALL BE COMPLETED BY EXPERIENCED WORKERS AND CRAFTSMEN AND IN ACCORDANCE WITH THE HIGHESTSTANDARDS OF THE INDUSTRY.

DIVISION 7 THERMAL AND MOISTURE PROTECTION1. ALL RIGID AND FIBERGLASS BATT INSULATION SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURERS'

RECOMMENDATIONS AND PER LOCAL ENERGY CONSERVATION REQUIREMENTS.

2. ROOFING MATERIALS, FLASHING, AND SEALANTS SHALL BE APPLIED IN KEEPING WITH THE MANUFACTURERS'RECOMMENDATIONS. ALL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST STANDARDSOF THE INDUSTRY ANDALL APPLICABLE SURFACES SHALL BE BROOM CLEANED, MOPPED, SMOOTH, AND DRY AS NEEDED PRIOR TO INSTALLATION.

3. CONTRACTOR SHALL THOROUGHLY INSPECT SITE CONDITIONS AND SHALL FURNISH ALL NECESSARY LABOR AND MATERIAL TOPROVIDE A COMPLETE AND WATER TIGHT INSTALLATION.

4. ALL FLASHING AND VALLEYS SHALL BE MADE OF PREMIUM ROOFING-GRADE COPPER AND SHALL BE SET TO PROVIDE AWATER-TIGHT INSTALLATION.

5. ALL GUTTERS AND DOWNSPOUTS SHALL BE SIZED AND SHAPED AS SPECIFIED.

6. MOISTURE/VAPOR BARRIERS AND VENTS SHALL BE INSTALLED THROUGHOUT THE PROJECT AS INDICATED ON THE DRAWINGSAND IN ACCORDANCE WITH STANDARD LOCAL PRACTICE.

7. OVERALL THERMAL PROTECTION AND WATERPROOFING WORK SHALL BE IN KEEPING WITH THE HIGHEST LEVEL OFWORKMANSHIP.

8. CONTRACTOR IS CAUTIONED THAT SCOPE OF WORK INCLUDES THE SELECT REMOVAL AND REPLACEMENT OF DEFECTIVEROOFING, COPING, FLASHING, GUTTERS, SCUPPERS,..ETC. CONTRACTOR IS RESPONSIBLE TO FULLY DELINEATE INTENDEDSCOPE OF WORK DURING THE BIDDING PROCESS AS NEEDED TO DELIVER A WATER TIGHT INSTALLATION.

DIVISION 8 DOORS, HARDWARE AND GLAZINGA. DOORS AND HARDWARE1. ALL DOORS SHALL MEET LOCAL CODE, FIRE REQUIREMENTS, AND PROJECT SPECIFICATIONS.

2. UNLESS OTHERWISE SPECIFIED BY GDG ALL DOORS, JAMBS AND CASINGS SHALL BE PROVIDED AND INSTALLED BYCONTRACTOR.

3. HARDWARE SHALL BE AS SPECIFIED AND MUST BE HANDLED WITH THE UTMOST CARE. ANY SPECIALTY ITEMS MUST BEAPPROVED BY GDG PRIOR TO ORDERING AND INSTALLATION.

4. ALL NEW DOORS SHALL BE KEYED IN ACCORDANCE AS PER DOOR SCHEDULE AND SHALL BE MATCHED TO THE EXISTINGBUILDING MASTER KEY.

5. ALL NEW KEYS SHALL HAVE (3) DUPLICATES AND SHALL BE PROPERLY TAGGED AND REMITTED TO GDG AND THE OWNER.

B. GLAZING1. ALL GLAZING TO BE AS SPECIFIED AND SIZED TO MEET LOCAL CODE REQUIREMENTS. SCOPE INCLUDES THE REMOVAL AND

REUSE OF EXISTING INTERIOR GLAZING AS WELL AS NEW GLAZING.

2. CONTRACTOR SHALL FIELD-VERIFY ALL DIMENSIONS AND SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG, TRIPLICATECOPIES OF THE GLAZING SHOP DRAWINGS.

3. WHERE APPLICABLE TEMPERED OR LAMINATE SAFETY GLASS SHALL BE USED AS REQUIRED BY CODE.

4. SEALANT COMPOUND SHALL BE AN ACRYLIC TERPOLYMER, "MONO," AS MANUFACTURED BY TERMCO MANUFACTURING CO.,DURON COMPANY, OR APPROVED SUBSTITUTE.

5. WINDOWS, GLAZING, AND WEATHER-STRIPPING PRODUCTS AND INSTALLATION SHALL BE IN KEEPING WITH THE HIGHEST LEVELSOF WORKMANSHIP.

DIVISION 9 FINISHESA. PLASTER AND DRYWALL1. ALL FRAMING SHALL BE SPACED NOT TO EXCEED STANDARD RECOMMENDED PRACTICE.

2. FASTENINGS AND JOINTS SHALL BE PREPARED, FINISHED AND SANDED TO PROVIDE A DRY, CLEAN AND SMOOTH SURFACE ANDSHALL BE COMPLETED ACCORDING TO THE MANUFACTURER'S GUIDELINES AND SPECIFICATIONS.

3. WHERE REQUIRED, GYPSUM BOARD SHALL BE A WATER-RESISTANT, FIRE-RESISTANT, OR EXTERIOR-GRADE PRODUCT ASMANUFACTURED BY U.S. GYPSUM COMPANY OR APPROVED EQUAL.

4. CONTRACTOR SHALL ENSURE THAT ALL SURFACES HAVE BEEN FULLY POINTED, SANDED, AND PREPARED PRIOR TO THEAPPLICATION OF THE FIRST COAT OF PRIMER PAINT.

5. CONTRACTOR IS RESPONSIBLE FOR CORRECTING ANY DEFECTS AND ANY POINT-UPS AND SKIMMING THAT MAY BE REQUIREDAFTER THE PRIMER PAINT COAT HAS BEEN APPLIED.

6. NO SANDING SHALL BE UNDERTAKEN UNTIL ALL LIGHTING FIXTURES HAVE BEEN PROPERLY PROTECTED AND ALL AIR RETURNSHAVE BEEN FULLY COVERED WITH AIR FILTERS.

7. CONTRACTOR SHALL CONFIRM AND COORDINATE THE INSTALLATION OF ALL IN THE WALL BLOCKING REQUIRED BY OTHERTRADES AND SHALL INCLUDE ANY WALL REPAIRS RESULTING FROM OPENINGS OR SURFACE CHANGES RESULTING FROM THEWORK OF OTHER TRADES.

I. GDG's RULES AND PROCEDURES FOR CONSTRUCTION PROJECTS

DIVISION 1 GENERAL NOTES1. THE GEORGETOWN DESIGN GROUP, INC. (GDG) HAS BEEN RETAINED BY DCPL AS THE PROJECT'S ARCHITECT AND IS THE SOLE

INTERPRETER OF THE PROJECT'S DESIGN INTENT AND REQUIREMENTS.

2. CONTRACTOR, ITS SUBS, AND SUPPLIERS SHALL THOROUGHLY REVIEW THE PLANS AND FAMILIARIZE THEMSELVES WITH THE SITEAND SHALL BRING TO THE ATTENTION OF GDG AND THE OWNER, PRIOR TO BIDDING AND COMMENCING WORK, ANY POSSIBLEDISCREPANCIES OR REQUEST FOR CLARIFICATIONS.

3. THE PROJECT'S PLANS AND DOCUMENTS ARE INTENDED TO REASONABLY REPRESENT THE PROJECT'S INTENDED SCOPE OF WORKAND THE CONTRACTOR SHALL BE FULLY RESPONSIBLE FOR THE TIMELY COMPLETION OF THE WORK AND THE IMPLEMENTATION OFALL SAFETY PROCEDURES, PRECAUTIONS AND CONSTRUCTION TECHNIQUES RELATED TO THE PROJECT.

4. CONTRACTOR SHALL MAINTAIN A DAILY LOG OF ALL ON-SITE ACTIVITIES, AND SHALL PROVIDE WEEKLY SUMMARIES TO GDG ANDTHE OWNER ON A REGULAR BASIS.

5. CONTRACTOR MUST COORDINATE ALL LOGISTICAL ISSUES INCLUDING ACCESS TO THE SITE, WORKING HOURS, REMOVAL OFDEBRIS, DELIVERY OF EQUIPMENT AND MATERIAL AND MUST ADHERE TO OWNER'S RESONABLE REQUIREMENTS AND APPLICABLELOCAL AND MUNICIPAL REGULATIONS.

6. CONTRACTOR IS FULLY RESPONSIBLE FOR THE PERFORMANCE AND PROFESSIONAL BEHAVIOR OF ITS OWN CREWS AND SUBS.

7. CONTRACTOR MUST ENSURE THAT SUITABLE CREW FACILITIES AND REFUSE CONTAINERS ARE MAINTAINED IN AN APPROPRIATELOCATION AND IN CLEAN CONDITIONS.

A. CODES AND REGULATIONS1. ALL WORKMANSHIP AND MATERIALS SHALL CONFORM TO THE REQUIREMENTS OF THE DISTRICT OF COLUMBIA CODES AND

REGULATIONS INCLUDING THE LATEST EDITIONS OF THE NATIONAL ELECTRICAL CODE AND NFPA 70.

2. CONTRACTOR AND ITS SUBS SHALL APPLY AND PAY FOR ALL REQUIRED TRADE PERMITS AND SHALL INCLUDE IN THEIR CONTRACTALL FEES INCIDENTAL TO THEIR WORK.

3. CONTRACTOR SHALL KEEP ON SITE AND HAVE ON FILE, SIGNED COPIES OF ALL REQUIRED PERMITS AS WELL AS ALL APPLICABLEINSPECTIONS.

B. INSURANCE AND CERTIFICATES1. PRIOR TO BEGINNING WORK, CONTRACTOR AND ITS SUBS SHALL PROVIDE A CURRENT COPY OF THEIR WORKERS COMPENSATION

AND COMPREHENSIVE COMMERCIAL LIABILITY INSURANCE CERTIFICATES INCLUDING ANY ADDITIONAL CONTRACTUALLY REQUIREDBY THE OWNER AND SHALL NAME GDG AND THE OWNER AS ADDITIONAL INSURED.

C. WARRANTIES1. CONTRACTOR AND ITS SUBS SHALL WARRANTY AND DILIGENTLY CORRECT, AT NO EXTRA CHARGE, ANY DEFECT IN THEIR WORK.

THE CORRECTION OF SUCH WORK SHALL INCLUDE ALL EXPENSES AND DAMAGES RESULTING FROM/OR CONNECTED TO THEREMOVAL, REPLACEMENT, OR REPAIR OF ANY PART OF WORK AND EXISTING CONDITIONS WHICH MAY HAVE BEEN DISTURBED ORDAMAGED AS A RESULT OF THEIR WORK.

2. EACH LABOR AND WORKMANSHIP WARRANTY SHALL BE PASSED TO THE OWNER AND SHALL BE VALID FOR A MINIMUM OF ONEYEAR FROM THE DATE OF FINAL ACCEPTANCE OF WORK BY GDG AND THE OWNER.

3. MATERIAL AND EQUIPMENT WARRANTIES SHALL ALSO BE PASSED TO THE OWNER AND SHALL BE VALID FOR THE FULL PERIODSPECIFIED BY THE MANUFACTURER FOLLOWING THE DATE OF FINAL ACCEPTANCE OF WORK BY GDG AND THE OWNER.

D. SHOP DRAWINGS & SUBMITTALS1. WHERE SPECIFIED AND/OR REQUIRED BY GDG AND THE SCOPE OF WORK, CONTRACTOR SHALL SUBMIT FOR REVIEW AND

APPROVAL BY GDG AND THE OWNER, TRIPLICATE COPIES OF SHOP DRAWINGS AND SUBMITTALS.

2. CONTRACTOR AND ITS SUBS ARE SPECIFICALLY INSTRUCTED TO FIELD-VERIFY ALL DIMENSIONS PRIOR TO PREPARING THEIR SHOPDRAWINGS AND STARTING FABRICATION OF ANY ITEM.

3. CONTRACTOR AND ITS SUBS ARE CAUTIONED THAT THEIR SHOP DRAWINGS MUST BE REVISED AS INSTRUCTED BY GDG AND MUSTBE APPROVED BY GDG AND THE OWNER PRIOR TO PROCEEDING WITH ANY FABRICATION OR INSTALLATION WORK.

E. SUPPLEMENTARY RULES1. DELIVERIES AND ACCEPTANCE OF ANY MATERIALS OR EQUIPMENT ORDERED BY CONTRACTOR AND ITS SUBS ARE THE FULL

RESPONSIBILITY OF THE CONTRACTOR.

2. ALL CONSTRUCTION MATERIALS AND ITEMS KEPT ON SITE SHALL BE CLEARLY LABELED, ORDERLY STORED, AND PROTECTED.

3. CONTRACTOR AND ITS SUBS ARE SPECIFICALLY CAUTIONED THAT THEY ARE SOLELY RESPONSIBLE FOR THE SAFEGUARDING OFTHEIR MATERIALS, EQUIPMENT, TOOLS, ETC. AND THAT NEITHER GDG NOR THE OWNER ARE RESPONSIBLE FOR ANY ITEMS LEFTOR STORED BY THEM AT THE SITE.

F. SCHEDULING AND COST CHANGES1. TIME IS OF THE ESSENCE AND EVERY EFFORT MUST BE MADE TO AVOID ANY DELAYS AND ENSURE THE PROPER SCHEDULING OF

THE WORK AND THE NECESSARY COORDINATION OF ALL TRADES.

2. WHEN ON-SITE CONDITIONS OR SIGNIFICANT CHANGES IN THE SCOPE OF WORK MAY POSSIBLY AFFECT THE PROGRESS OR THECOST OF THE PROJECT, SUCH CHANGES MUST BE SUBSTANTIATED IN WRITING AND IMMEDIATELY BROUGHT TO THE ATTENTION OFGDG.

3. ANY SCHEDULING CHANGES OR PROPOSED COST-RELATED CHANGE ORDERS MUST BE TIMELY SUBMITTED FOR REVIEW BY GDGAND APPROVAL IN WRITING BY OWNER PRIOR TO MAKING ANY SCHEDULE CHANGES OR INCURRING ANY RELATED COSTS.

G. ALLOWANCES AND ALTERNATES:1. THE SCOPE OF WORK OUTLINED IN THE BID SET INCLUDES VARIOUS ALLOWANCES AND ALTERNATES THAT ARE SUBJECT TO

PRIOR REVIEW BY GDG AND APPROVAL BY THE OWNER PRIOR TO THEIR IMPLEMENTATION.

DIVISION 2 SITE CONSTRUCTION1. CONTRACTOR AND ITS SUBS SHALL PROTECT ALL EXISTING STRUCTURES AND INSTALLATIONS AGAINST ANY KIND OF DAMAGE.

2. TEMPORARY CONSTRUCTION BARRICADES AND, WHERE APPLICABLE, DUST SHIELDS MUST BE INSTALLED AS INSTRUCTED PRIORTO BEGINNING ANY WORK.

3. EXISTING LANDSCAPING, TREES, STRUCTURES AND CONSTRUCTION WHICH IS SCHEDULED TO REMAIN SHALL BE PROTECTED, ANDSHALL REMAIN UNDISTURBED. ALL NECESSARY CUTS SHALL BE NEAT AND STRAIGHT AND ANY CONDITION DISTURBED BY ACONTRACTOR AND NOT SCHEDULED FOR CHANGE SHALL BE FULLY CORRECTED AT THE CONTRACTOR'S SOLE EXPENSE.

4. ANY EXCAVATION AND IN-GROUND WORK MUST BE FULLY COORDINATED WITH MISS UTILITY AND MUST BE APPROVED BY GDG ANDCOORDINATED WITH OTHER TRADES AND UTILITIES THAT MAY BE AFFECTED BY THE WORK.

5. SILT FENCES AND APPLICABLE SITE EROSION CONTROLS SHALL BE INSTALLED AND MAINTAINED AS NEEDED AND IN ACCORDANCEWITH LOCAL REGULATIONS

6. DEBRIS AND EXCESS MATERIALS MUST BE PROMPTLY REMOVED FROM THE SITE ON A DAILY BASIS

7. BOOKS AND MEDIA AND EQUIPMENT HANDLING: CONTRACTOR SHALL RETAIN THE SERVICES OF A SUBCONTRACTOR WITH PROVENEXPERIENCE IN THE REMOVAL, RELOCATION, AND RE-STOCKING OF BOOKS, OTHER MEDIA, AND EQUIPMENT SLATED TO BERELOCATED AS A RESULT OF THE NEW WORK. UNLESS SUBCONTRACTOR IS A PRE-APPROVED COMPANY SUCH AS "NATIONALLIBRARY RELOCATIONS "OR" OFFICE MOVERS-KANE CO." CONTRACTOR'S PROPOSED RELOCATION SUBCONTRACTOR MUST BESUBMITTED FOR DCPL'S REVIEW AND APPROVAL. EXTENT OF MEDIA, FURNITURE, AND EQUIPMENT REMOVAL/RELOCATION SHALLBE AS CONFIRMED BY DCPL DURING PRE-BID WALK-THRU.

DIVISION 3 CONCRETE1. ALL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST STANDARDS AND SPECIAL ATTENTION SHALL BE PROVIDED

TO THE ACCURATE LEVELING OF THE CONCRETE AND TO THE PLACEMENT OF APPLICABLE CONTROL JOINTS.

2. ALL CONCRETE WORK SHALL BE EXECUTED IN ACCORDANCE WITH THE PROJECT'S REQUIREMENTS AND HIGHEST APPLICABLETRADE SPECIFICATIONS.

B. TILE WORK(NOT APPLICABLE)

C. CARPET AND VCT1. FLOORING INSTALLATION SHALL NOT PROCEED UNTIL ALL FLOOR DEFECTS HAVE BEEN CORRECTED, ALL FOREIGN MATTERS HAVE

BEEN REMOVED, CRACKS HAVE BEEN SEALED, AND ALL SURFACES FULLY LEVELED.

2. DRY OR DUSTY CONCRETE OR MASONRY SURFACES SHALL BE CLEANED PRIOR TO INSTALLATION.

3. WHERE APPLICABLE FLOOR SLEEPERS, VAPOR BARRIER, SUBFLOORING, FLOOR LEVELING AND ACTUAL FLOORING INSTALLATIONSHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST WORKMANSHIP STANDARDS AND IN KEEPING WITH THEMANUFACTURERS' RECOMMENDATIONS.

4. FLOORING AND SPECIFIED WALL BASE MUST BE INSTALLED AND FINISHED IN ACCORDANCE WITH THE HIGHEST STANDARDS ANDMUST BE IN KEEPING WITH THE APPROVED COLOR SELECTIONS. ALL NEW CARPET AND VCT MUST BE FULLY PROTECTED WITHAPPLICABLE LIGHT-ADHERENCE COVERING UNTIL ALL OTHER WORK HAS BEEN COMPLETED.

D. PAINTING1. ALL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE HIGHEST STANDARDS. ALL SURFACES SHALL BE SANDED TO A

SMOOTH FINISH PRIOR TO BEING STAINED OR PRIMED FOR PAINT.

2. PAINT SHALL BE FIRST LINE PRODUCTS AS SPECIFIED AND MANUFACTURED BY SHERWIN WILLIAMS PREMIUM PAINTS, BENJAMINMOORE PAINTS OR APPROVED EQUAL.

3. ALL PAINTED WORK SHALL RECEIVE A MINIMUM OF 3 COATS INCLUDING A PIGMENTED PRIMER COAT..

4. COLORS SHALL BE AS SPECIFIED AND UNLESS OTHERWISE AGREED UPON, CONTRACTOR SHALL EXECUTE FOR EACH DESIGNATEDAREA UP TO (4) 24" X 24" ON-SITE COLOR TESTS THAT SHALL BE SUBJECT TO FINAL APPROVAL BY GDG AND OWNER.

DIVISION 10 SPECIALTIES1. CONTRACTOR SHALL RELY ON OWNER'S ALLOWANCE TO PREPARE A COMPREHENSIVE LIST OF ALL NEW INTERIOR SIGNS REQUIRED BY THE THE PROJECT. ALL NEW SIGNS COPY AND SHOP DRAWINGS MUST BE REVIEWED BY GDG AND APPROVED BY OWNER

2. SIGNS MUST BE FABRICATED BY AN ESTABLISHED SIGN COMPANY IN ACCORDANCE WITH DCPL'S STANDARD SIGNAGE SPECIFICATIONS.

DIVISION 11 EQUIPMENT1. SCOPE OF WORK INCLUDES THE PROCUREMENT AND INSTALLATION OF ENTRANCE HYBRID SECURITY DETECTOR GATES AS SHOWN ON SHEET A1. PRODUCT SHALL BE "SMART GATE 570" AS MANUFACTURED BY ITG/BIBLIOTHECA. CONTRACTOR SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG AND OWNER CATALOGUE CUTS AND TECHNICAL INFORMATION OF ALL RELATED EQUIPMENT AND MATERIALS.

DIVISION 12 FURNISHINGSALL FFE'S SHOWN ARE FOR REFERENCE PURPOSES ONLY AND ARE N.I.C.

DIVISION 13 SPECIAL CONSTRUCTION(NOT APPLICABLE)

DIVISION 14 CONVEYING SYSTEMS(NOT APPLICABLE)

DIVISION 15 MECHANICAL A. PLUMBING1. CONTRACTOR SHALL INCLUDE IN HIS TASK THE VERIFICATION EXISTING CONDITIONS AND THE FURNISHING OF ALL LABOR,

MATERIAL, EQUIPMENT AND SERVICES NECESSARY AND INCIDENTAL TO THE SUCCESSFUL COMPLETION OF THE WORK, FROMROUGH-IN TO FINAL INSTALLATION.

2. PRIOR TO ORDERING AND INSTALLATION CONTRACTOR SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG AND OWNERCATALOGUE CUTS AND TECHNICAL INFORMATION OF ALL RELATED EQUIPMENT AND MATERIALS.

3. CONTRACTOR IS SPECIFICALLY INSTRUCTED TO COORDINATE ALL WORK WITH OTHER TRADES TO ENSURE THAT ALL EQUIPMENTAND FIXTURES ARE INSTALLED IN ACCORDANCE WITH PLANS AND PER GDG'S ON-SITE INSTRUCTIONS.

4. ALL PLUMBING FIXTURES, SHALL BE FURNISHED AND INSTALLED BY CONTRACTOR.

5. THIS SET DOES NOT INCLUDE ANY PLUMBING DRAWINGS. CONTRACTOR MUST REFER TO THE ARCHITECTURAL PLANS AS NEEDEDTO DETERMINE THE INTENDED SCOPE OF WORK, COMPLY WITH THE OWNER'S REQUIREMENTS, AND ENSURE THAT THE WORK ISCODE COMPLIANT.

B. HEATING AND COOLING1. CONTRACTOR SHALL INCLUDE IN HIS TASK ALL LABOR, MATERIAL, EQUIPMENT AND SERVICES NECESSARY AND INCIDENTAL TO THE

SUCCESSFUL COMPLETION OF THE WORK, FROM ROUGH-IN TO FINAL INSTALLATION.

2. PRIOR TO ORDERING AND INSTALLATION CONTRACTOR SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG CATALOGUE CUTS ANDTECHNICAL INFORMATION ON ALL EQUIPMENT, EXHAUST FANS, AIR DIFFUSERS AND GRILLES, THERMOSTATS, ETC.

3. CONTRACTOR IS SPECIFICALLY INSTRUCTED TO COORDINATE ALL WORK WITH THE PLUMBING AND ELECTRICAL WORK AND TOENSURE THAT ALL DUCTS AND DIFFUSERS ARE INSTALLED IN ACCORDANCE WITH THE PLANS AND IN KEEPING WITH GDG'S ON-SITEINSTRUCTIONS.

5. CONTRACTOR MUST REFER TO THE ARCHITECTURAL, MECHANICAL, AND ELECTRICAL PLANS AS NEEDED TO DETERMINE THEINTENDED SCOPE OF WORK, COMPLY WITH THE OWNER'S REQUIREMENTS, AND ENSURE THAT THE WORK IS CODE COMPLIANT.

DIVISION 16 ELECTRICAL A. GENERAL1. CONTRACTOR SHALL INCLUDE IN HIS TASK THE VERIFICATION OF FURNISHING OF ALL LABOR, MATERIAL, EQUIPMENT AND

SERVICES NECESSARY AND INCIDENTAL TO THE SUCCESSFUL COMPLETION OF THE WORK, FROM ROUGH-IN TO FINALINSTALLATION.

2. PRIOR TO ORDERING AND INSTALLATION CONTRACTOR SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG CATALOGUE CUTS ANDTECHNICAL INFORMATION ON ALL EQUIPMENT PROVIDED BY THE CONTRACTOR.

3. CONTRACTOR IS SPECIFICALLY INSTRUCTED TO COORDINATE ALL WORK WITH THE PLUMBING AND MECHANICAL CONTRACTORSAND TO ENSURE THAT ALL RECEPTACLES, SWITCHES AND FIXTURES ARE INSTALLED IN ACCORDANCE WITH THE ARCHITECTURALPLANS AND IN KEEPING WITH GDG'S ON-SITE INSTRUCTIONS.

4. CONTRACTOR MUST REFER TO THE ARCHITECTURAL, ELECTRICAL, AND MECHANICAL PLANS AS NEEDED TO DETERMINE THEINTENDED SCOPE OF WORK, COMPLY WITH THE OWNER'S REQUIREMENTS, AND ENSURE THAT THE WORK IS CODE COMPLIANT.

5. CONTRACTOR SHALL COORDINATE WITH GC ALL CEILING AND WALL OPENINGS AS WELL AS SLAB CUTTING AND PATCHING WORKTO ENSURE THAT INTENDED SCOPE IS COVERED WITHOUT COST DUPLICATIONS.

B. ELECTRICAL FIXTURES1. ALL ELECTRICAL FIXTURES SHALL BE FURNISHED AND INSTALLED BY CONTRACTOR.

C. FIRE ALARM1. FIRE ALARM DEVICES SHOWN ON THE DRAWINGS ARE FOR GENERAL REFERENCE PURPOSES ONLY AND ARE NOT INTENDED TO LIMIT THE SCOPE OF WORK.

2. CONTRACTOR SHALL RETAIN THE SERVICES OF AN EXPERIENCED FIRE ALARM SUBCONTRACTOR AND MUST ENSURE THAT THE FIRE ALARM SYSTEM IS UPGRADED AS NEEDED TO BE CODE COMPLIANT.

3. PRIOR TO ORDERING AND INSTALLATION CONTRACTOR SHALL SUBMIT FOR REVIEW AND APPROVAL BY GDG A PLAN SHOWING THELOCATION OF ALL PROPOSED DEVICES ALONG WITH CATALOG CUTS AND TECHNICAL INFORMATION OF ALL RELATED EQUIPMENTAND MATERIAL.

D. VOICE, DATA, SECURITY1. INTERNET, TELEPHONE, SOUND, AND ALARM SYSTEM WORK SHALL BE CONTRACTED BY OWNER AND SITE COORDINATED BY CONTRACTOR.

2. WHERE APPLICABLE CONTRACTOR SHALL PROVIDE THE NECESSARY CONDUITS AND PULL LINES NEEDED TO COMPLETE THE INTENDED INSTALLATION.

3. UNLESS OTHERWISE INSTRUCTED BY OWNER CONTRACTOR'S WORK SHALL INCLUDE THE INSTALLATION AND TERMINATION OF ALL VOICE AND DATA WIRING. EXCEPT THAT OWNER SHALL BE RESPONSIBLE FOR TERMINATION OF VOICE/DATA WIRING AT MAIN SWITCHES.

SPECIAL CONDITIONSCONTRACTOR AND ITS SUBS ARE SPECIFICALLY DIRECTED TO COMPLY WITH GDG'S REQUIREMENTS AND TO BRING TO THE ATTENTIONOF GDG PRIOR TO BIDDING AND PRIOR TO STARTING WORK ANY DISCREPANCIES OR QUESTIONS PERTAINING TO THE PROJECT'SPLANS AND INTENDED SCOPE OF WORK.

* * *

PERMIT SET 01-16-15

BID SET 01-22-15

G2



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: General Specifications

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

GENERAL SPECIFICATIONS:

DIVISION 7INTERIOR WALL WATERPROOOFING:

BELOW GRADE WALL WATERPROOFING SHALL BE A SELF-CURING LIQUID RUBBERPOLYMER THAT FORMS A SEAMLESS WATERPROOFING MEMBRANE CAPABLE OFFULLY BONDING AND PENETRATING INTO CONCRETE SURFACE. PRODUCT SHALL BE

TO GDG'S APPROVAL. SEE SECTION 1/A1.

ROOFING:NEW ROOFING ASSEMBLY SHALL BE FROM SINGLE ROOFING MANUFACTURER ANDSHALL HAVE A 2-YEAR MINIMUM LABOR AND MATERIAL WARRANTY AGAINST ANY LEAKSOR DEFECTS FROM INSTALLER AND A 25-YEAR MINIMUM MANUFACTURER WARRANTYAGAINST ANY DEFECTS.

NEW ROOFING SHALL INCLUDE:

TWO-PLY HEAT-WELDED MODIFIED BITUMEN MINERAL-SURFACED ROOFING BASE

JOHNS MANVILLE CO.

ROOFING MATERIALS SHALL BE FROM JOHNS MANVILLE CO. OR SIMILAR PRODUCTSFROM SINGLE ROOFING MANUFACTURER SUBJECT TO APPROVAL BY GDG.

DIVISION 8:INTERIOR METAL DOORS:

NEW METAL DOORS AND FRAMES TO BE FIRE-RATED HOLLOW STEEL.ALL NEW DOORS MUST COMPLY W/ ACCESSIBILITY AND EGRESS CODEREQUIREMENTS.DOORS SHALL BE AS MANUFACTURED BY STEELCRAFT, B-SERIES DOORS ORSIMILAR SUBJECT TO GDG'S APPROVAL.

DOOR HARDWARE:ALL NEW DOOR HARDWARE MUST MATCH EXISTING AND COMPLY W/ ACCESSIBILITYAND EGRESS CODE REQUIREMENTS.

MANUFACTURED GLAZING SYSTEM:GLAZING SYSTEM PARTITIONS TO BE 84"H DEMOUNTABLE PARTITIONS W/ METALFRAMING CUSTOM FINISHED TO MATCH EXISTING "GREEN" FRAMING COLOR WITHLAMINATED 6MM MIN. GLASS PANELS.GLAZING SYSTEM GLASS DOORS TO BE 10MM MIN. SELF CLOSING HINGED DOORS W/ARCHIETCTURAL HANDLES (STYLE TBC).SYSTEN TO BE AS MANUFACTURED BY HAWORTH "ENCLOSE" OR SIMILAR PRODUCTSUBJECT TO APPROVAL BY GDG.

DIVISION 10:RESTROOM PARTITIONS:

PARTITIONS AND URINAL SCREENS TO BE ADA COMPLIANT ANDFLOOR/WALL-BRACED, AS MANUFACTURED BY BRADLEY CORP., SERIES 500, WITH#304 STAINLESS STEEL FINISH AND 5WL (DIAMOND) PATTERN, OR SIMILAR PRODUCTSUBJECT TO GDG'S APPROVAL.

CORNER GUARDS:

SUPPLIED ADHESIVE, BY WALLGUARD.COM OR SIMILAR PRODUCT SUBJECT TOGDG'S APPROVAL.

WALL GUARDS:

WITH CONCEALED FASTENERS AND IMPACT CHUSHIONS, COVERED WITHRUBBERIZED VINYL COVER WITH MATCHING END CAPS , COLOR TBC. INSTALLATION

WALLGUARD.COM OR SIMILAR PRODUCT SUBJECT TO GDG'S APPROVAL.

SOLAR AND PRIVACY SHADES:SHADES SHALL BE MANUALLY OPERABLE AND SHALL BE MADE FROM A WOVENREINFORCED VINYL AND POLYESTER CLOTH WITH A 5% (TBC) OPEN DENSITY ALONGEXTERIOR GLAZING AND 10% (TBC) DENSITY ALONG INTERIOR GLAZING.

SHADES SHALL BE MADE OF SINGLE BAND, REGULAR ROLL, NON-RAILROADED,

(COLOR TBC).

MECHOSYSTEMS CO. OR SIMILAR MANUFACTURER SUBJECT TO GDG'S APPROVAL.

FIRE EXTINGUISHER CABINETS:

PRODUCT, WITH PARTIAL ACRYLIC DOOR GLAZING. INSIDE BOX DIMENSIONS:

MANUFACTURED BY LARSEN MANUFACTURING, ARCHITECTURAL SERIES, MODELAL-FS 2409-R7, WITH FACTORY PAINT (COLOR TBC), OR SIMILAR PRODUCT SUBJECTTO GDG'S APPROVAL.

SECURITY GATES:SECURITY GATES AS MANUFACTURED BY BIBLIOTHECA, SMARTGATE 570 SERIESDOUBLE AISLE GATES W/ SMARTGATE MANAGERS SOFTWARE AND SMARTGATEPEDESTAL CONFIGURATION SOFTWARE.

COAT HOOKS:PRODUCT SHALL BE HEAVY DUTY GARMENT HOOK DIE-CAST WITH NICKEL FINISH,

BY NATIONAL MANUFACTURING CO. OR SIMILAR MANUFACTURER SUBJECT TO GDG'SAPPROVAL.

DIVISION 11:PROJECTION SCREENS:

CEILING-RECESSED AUTOMATED PROJECTION SCREEN SHALL BE AS

VIEWING AREA WITH MATTE WHITE SURFACE XT1000E. ASSEMBLY SHALL INCLUDE

WALL MONITOR:WALL MONITOR TO BE 40" DIAGONAL SCREEN MIN. WITH HIGH RESOLUTION DISPLAY, VIDEO,RGB/DVI, AND HDMI INTERFACES, AS MANUFATURED BY SAMSUNG #SMT-4023 OR SIMILARSUBJECT TO APPROVAL BY GDG.

WALL MONITOR WALL MOUNT:WALL MONITOR MOUNTING SYSTEM FOR USE WITH 40" MONITOR TO FEATURE 15 DEGREESOF TILT & LOCK ADJUSTMENT AS MANUFACTURED BY MUSTANG #MV-TILT2B, OR SIMILARSUBJECT TO APPROVAL BY GDG.

MICROWAVE:NEW MICROWAVE TO BE 1.2 CU. FT. MIN AS MANUFACTURED BY PANASONIC #NN-SA651S ORSIMILAR SUBJECT TO APPROVAL BY GDG.

DIVISION 15:WORKROOM SINK:

SINK SHALL BE STAINLESS STEEL DROP-IN TYPE AS MANUFACTURED BY ELKAY

WORKROOM FAUCET:FAUCET SHALL BE ADA COMPLIANT AND VANDAL RESISTANT WITH WASHERLESSCERAMIC VALVING AS MANUFACTURED BY KOHLER MANUFACTURING CO.

HANDLES, WITH POLISH CHROME FINISH, OR SIMILAR PRODUCT SUBJECT TO GDG'SAPPROVAL.

BATHROOM SINKS:SINK SHALL BE UNDERMOUNT TYPE AS MANUFACTURED BY KOHLERMANUFACTURING CO.,

APPROVAL.

BATHROOM FAUCETS:FAUCET SHALL BE ADA COMPLIANT AND VANDAL RESISTANT WITH WASHERLESSCERAMIC VALVING AS MANUFACTURED BY KOHLER MANUFACTURING CO.

WITH POLISH CHROME FINISH, OR SIMILAR PRODUCT SUBJECT TO GDG'S APPROVAL.

AIR GRILLES:

EXISTING FLOOR AIR RETURN GRILLES AND SIZED AS SHOWN ON DRAWINGS. GRILLESSHALL BE AS MANUFACTURED BY WAINLANDS INC. OR SIMILAR MANUFACTURER SUBJECTTO GDG'S APPROVAL.

DIVISION 16:ELECTRICAL RECESSED FLOOR BOXES:

RECESSED FLOOR BOXES SHALL BE AS MANUFACTURED BY LEGRAND-WIREMOLD

INSTALLATION SHALL INCLUDE ALL CONDUITS AND WIRING FOR POWER, DATA, ANDVOICE RECETACLES/PORTS SHOWN ON DRAWINGS.

NOTE: AS PART OF ITS PRODUCT SUBMITTALS, CONTRACTOR SHALL PROVIDE (1)BOX WITH COVER EQUIPPED WITH THE SPECIFIED RECEPTACLES AND PORTS FORREVIEW AND APPROVAL BY GDG AND DCPL PRIOR TO FINAL ORDERING. UPONORDERING SAMPLE BOX MAYBE INCORPORATED IN WORK.

EXIT SIGNS:SIGNS SHALL HAVE A THERMOPLASTIC HOUSING THAT IS IMPACT ANDSCRATCH-RESISTANT, CORROSION-PROOF, AND UV-STABILIZED WITH BUILT-IN LEDLAMP. EACH SIGN SHALL INCLUDE AN EXTRA FACE-PLATE AND DIRECTIONALKNOCKOUTS AS NEEDED FOR FIELD-CONVERSION TO MEET SITE REQUIREMENTS,AND SHALL BE EQUIPPED WITH A TEST SWITCH AND STATUS INDICATOR ANDFACTORY SCHEDULED SELF-DIAGNOSTIC TEST WITH AUTOMATIC RE-CHARGE.

SIMILAR MANUFACTURER SUBJECT TO GDG'S APPROVAL.

FIRE ALARM NOTIFICATIONS DEVICES:DEVICES SHALL BE COMPATIBLE WITH EXISTING FIRE ALARM SYSTEM, FIELDPROGRAMMABLE, AND SHALL PROVIDE SYNCHRONIZED AUDIBLE HORNS ANDVISUAL SIGNALS. DEVICES HOUSING SHALL BE MADE FROM FIRE-RETARDANT ANDIMPACT RESISTANT MATERIAL. DEVICES SHALL MEET APPLICABLE CODEREQUIREMENTS INCLUDING AUDIBLE LEVEL AND CANDELA REQUIREMENTSSPECIFIC TO EACH SPACE. DEVICES SHALL HAVE A RED FINISH WITH WHITE

EDWARDS SIGNALING, OR "WHEELOCK" BY COOPER INDUSTRIES OR SIMILARMANUFACTURER SUBJECT TO GDG'S APPROVAL.

FIRE PULL DEVICES:DEVICES SHALL BE COMPATIBLE WITH EXISTING FIRE ALARM SYSTEM AND SHALL BESINGLE OR DOUBLE ACTION AS NEEDED BY SITE CONDITIONS. DEVICES SHALL BEMOUNTED SEMI-FLUSH WITH APPLICABLE BACK BOX. DEVICES SHALL MEETAPPLICABLE CODE REQUIREMENTS AND SHALL HAVE A RED FINISH WITH WHITE

EDWARDS SIGNALING, "WHEELOCK" BY COOPER INDUSTRIES, OR SIMILARMANUFACTURER SUBJECT TO GDG'S APPROVAL.

SURFACE MOUNTED 1X4 FIXTURE:LIGHTING FIXTURE TO BE SIMILAR TO COOPER LIGHTING METALUX #MC228T5 1X4WITH ENCLOSED BULB, OR SIMILAR MANUFACTURER SUBJECT TO GDG'SAPPROVAL..

CEILING SUSPENDED 1X4 FIXTURES:LIGHTING FIXTURE TO BE SIMILAR TO COOPER LIGHTING CORELITE-JALUM SERIES,OR SIMILAR MANUFACTURER SUBJECT TO GDG'S APPROVAL.

RECESSED 2X4 FIXTURES:TO MATCH EXISTING FIXTURES.

RECESSED MILLWORK LIGHTS:FIXTURES SHALL BE DIE-CAST WITH STEEL HOUSING AND GLASS LENS MADE TO FIT IN

SOURCES, MODEL HR-LED87-DB WITH DARK BRONZE FINISH, WITH CLASS 2 ELECTRONICTRANSFORMER EN02460-RBE, AS MANUFACTURED BY WAC LIGHTING OR SIMILARMANUFACTURER SUBJECT TO GDG'S APPROVAL.

DB



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: Basement Demo Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

BASEMENT DEMO PLAN

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

D1



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: 1st Floor Demo Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

1ST FLOOR DEMO PLAN

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

D2



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: 2nd Floor Demo Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

DEMO 2ND FLOOR

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

AB



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: Basement Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

BASEMENT PLAN

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

A1



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: 1st Floor Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

1ST FLOOR PLAN

GDGGDGDESIGN BUILD


CAVITY FILL DETAILSCALE 3

8" = 1'1

PERMIT SET 01-16-15

BID SET 01-22-15

A2



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: 18" = 1'

Sheet Title: 2nd Floor Plan

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

2ND FLOOR PLAN

GDGGDGDESIGN BUILD


PERMIT SET 01-16-15

BID SET 01-22-15

A3



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: AS NOTED

Sheet Title: Architectural Details

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

ARCHITECTURAL DETAILS

GDGGDGDESIGN BUILD


ELEVATIONSCALE 3

8" = 1'1 ELEVATIONSCALE 3

8" = 1'2

ELEVATIONSCALE 3

8" = 1'3 ELEVATIONSCALE 3

8" = 1'4

WALL TYPE 1SCALE 1" = 1'1 WALL TYPE 2

SCALE 1" = 1'2 WALL TYPE 3SCALE 1" = 1'3 WALL TYPE 4

SCALE 1" = 1'3

MANUFACTURED GLAZING SYSTEM NOTES:(ROOMS 200A, 200B, 200C, AND 200D )

METAL FRAMING TO BE CUSTOM FINISHED TO MATCH EXISTING "GREEN" FRAMING COLOR.

LAMINATED 6MM MIN. GLASS PANELS.LAMINATED 10 MM MIN. SELF-CLOSING HINGED GLASS DOORS WITH

ARCHITECTURAL HANDLES (STYLE TBC).INSTALLATION TO BE SECURED TO EXISTING STRUCTURE AS NEEDED TO

ENSURE ITS STABILITY.

SYSTEM SHALL BE AS MANUFACTURD BY HAWORTH OR APPROVED SUBSTITUTE.

PERMIT SET 01-16-15

BID SET 01-22-15

A4



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: AS NOTED

Sheet Title: Millwork Details

JUANITA E.THORNTON


LIBRARYRENOVATION


20012

MILLWORK DETAILS

GDGGDGDESIGN BUILD


STAFF WORK ROOM PLANSCALE 3

8" = 1'1

STAFF WORK ROOM ELEVATIONSCALE 3

8" = 1'A STAFF WORK ROOM ELEVATIONSCALE 3

8" = 1'B


8" = 1'C


8" = 1'D


8" = 1'E


8" = 1'F

SEE SHEET A5

MILLWORK NOTES

PERMIT SET 01-16-15

BID SET 01-22-15

STAFF WORK ROOM SECTIONSCALE 3

8" = 1'G

A5



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: AS NOTED


JUANITA E.THORNTON


LIBRARYRENOVATION


20012

MILLWORK DETAILS

GDGGDGDESIGN BUILD


STAFF WORK SHELVING PLANNOT TO SCALE

SHELVING DETAILSCALE 3

4" = 1'A

SHELVING DETAILSCALE 3

4" = 1'B

EARLY LEARNING DESK OVERVIEW1A SCALE 34" = 1'

EARLY LEARNING DESK SIDE ELEVATION1C SCALE 34" = 1'

EARLY LEARNING DESK PLAN1B SCALE 34" = 1'

EARLY LEARNING DESK SECTION1D SCALE 34" = 1'

EARLY LEARNING DESK FRONT ELEVATION1E SCALE 34" = 1'

CHILD'S LIBRARIAN DESK PLAN2A SCALE 38" = 1'

CHILD'S LIBRARIAN DESK PLAN2B SCALE 38" = 1'

CHILD'S LIBRARIAN DESK FRONT ELEVATION2C SCALE 38" = 1'

CHILD'S LIBRARIAN DESK SIDE ELEVATION2D SCALE 38" = 1'

SHELVING DETAILSCALE 1 12" = 1'C

CHILD'S LIBRARIAN DESK SIDE ELEVATION2E SCALE 34" = 1'

SHELVING & CABINETS INSTALLATION NOTESCONTRACTOR SHALL PROVIDE IN-WALL BLOCKING AS NEEDED TO SUPPORT AND SECURESHELVING, CABINETS, AND COUNTERS.

LOCATION, AND USE HEAVY-DUTY WALL ANCHORS AS NEEDED TO PROVIDE A SECURELOAD-BEARING INSTALLATION.

BLOCKING LOCATION, AND USE HEAVY-DUTY WALL ANCHORS AS NEEDED TO PROVIDE A SECURELOAD-BEARING INSTALLATION.

SHELVING & CABINETS HARDWARE SPECS1. WALL STANDARDS:

2. SHELVING BRACKETS:

3. COUNTER BRACKETS:

4. CABINET DOOR PULLS:

5. CAB DOOR HINGES:

6. DRAWER SLIDES:

7. COUNTER GROMMETS:

8. CABLE TRAYS:P4-AWB32 & #P4-AWB26 AS APPLICABLE

TACKBOARDS

DESIGNATED FABRIC. USE SPRAY ADHESIVE TO EVENLY SECURE FABRIC TO BOARD.

FABRIC 1: KNOLL FABRIC, PATINA # W 1007/6 (ROOMS # 203, 103A)FABRIC 2: KNOLL FABRIC, OCHRE # W1007/5 (ROOMS # 101A, 115)

LAMINATESLAM-1 (DESKS):

LAM-2 (DESKS):

LAM-3 (BOOKBINS): GRENADINE 6902-MC

LAM-4 ( WORK ROOM COUNTERS AND SHELVES): FORMICA "CAFE WEFT" 5879-58

LAM-5 (WORK ROOM CABINETS): FORMICA "BURNISHED GLAZE" 7704-58

LAM-6 (STAFF LOUNGE COUNTER): PIONITE "VALLEY OF THE SUN" AO201 SUEDE

LAM-7 (RESTROOM COUNTER SUPPORT): FORMICA "BURNT STRAND"

SOLID SURFACECORIAN-1 (DESKS): SAHARA

CORIAN-2 (RESTROOM COUNTER): SILVER BIRCH

SLAT WALLMARLITE: 318 WINDSOR ANIGRE

STORAGE UNIT PLAN3A SCALE 38" = 1'

STORAGE UNIT ELEVATION3B SCALE 38" = 1'

STORAGE UNIT SECTION3C SCALE 34" = 1'

MILLWORK NOTES

PERMIT SET 01-16-15

BID SET 01-22-15

CHILDREN'S TACKBOARDS ELEVATION4A SCALE 12" = 1'

CORIAN SURFACE JOINT

CORIAN-1 SURFACE JOINT

WORK ROOM

CABLEMANAGEMENTTRAY

U/C MOBILE FILE CAB BELOW COUNTER (SHOWN AS 15"X 22"X27" NOT PART OF MILWORK)

WORK ROOM

CIRC/INFO DESK PLAN1A SCALE 38" = 1'

CIRC/INFO DESK PLAN1B SCALE 38" = 1'

CIRC/INFO DESK ELEVATION1C SCALE 38" = 1'

CIRC/INFO DESK ELEVATION1D SCALE 38" = 1'

SECTION 11F SCALE 34" = 1'

CIRC/INFO DESK ELEVATION1E SCALE 38" = 1'

SECTION 21G SCALE 34" = 1'

A6



TEL: (202) 857-0060FAX: (202) 857-0089


Revisions:

Scale: AS NOTED


JUANITA E.THORNTON


LIBRARYRENOVATION


20012

GDGGDGDESIGN BUILD


MILLWORK DETAILS CIRC/INFO DESK

U/C MOBILEFILE CAB

BELOW NIC.

2 1/2" GROMMETU/C CABLE MANAGEMENT TRAY

COUNTERSUPPORTBRACKETS

COUNTERSUPPORTBRACKET

U/C MOBILEFILE CAB NIC.

FABRIC COVERED1/2" HOMASOTEBOARD WITH BACKMETAL CLEATS

FABRICKNOLL COLOR:OCHRE # W1007/5

"RAKKS" WALL TRACKS AND ADJUSTABLE

BRACKETS

CABLE MGMT. TRAY

COUNTERSUPPORT BRACKETOPTION 1NOTE:SEE TYPICALSUPPORT DETAILFOR OPTION 2

FLOOR

U/C MOBILEFILE CABNIC.

WALL TRACKS

LAMINATED COUNTER LAM-4

FABRIC ON 1/2"HOMASOTE W/ BACKMETAL CLEATS

CABLEMGMT.TRAY

212

U/C MOBILEFILE CABNIC

2 1/2"GROMMET SUPPORT

BRACKET

U/C CABLE MAGMT. TRAY

SUPPORTBRACKET

CABLE MGMT. TRAYU/C MOBILE

FILE CABNIC.

"RAKKS"WALL TRACKS& ADJUSTABLEBRACKETS

LAM-4 SHELVES W/ LIP SEE DETAIL 3C/ A6

EXISTING WALL

LAMINATED SHELVES

EXISTING WALL

LAM-1 SHELVES

FABRIC COVERED 1/2" HOMASOTE BOARD WITH BACK METAL CLEATS

FABRIC KNOLL COLOR: PATINA # W1007/6 NOTE:

ADVISE GDG AND USE THIS SUPPORT WHERE IT IS NOTFEASIBLE TO FULLY SECURE U/C ALUMINUM BRACKETS.

1" ALUMINUMANGLE

CIRCULATION WORKROOM PLAN2A SCALE 38" = 1'

CIRCULATION WORKROOM ELEVATION2B SCALE 38" = 1'

CHILD'S LIBRARIAN WORKROOM PLAN3A SCALE 38" = 1'

CHILD'S LIBRARIAN WORKROOM ELEVATION3B

TYPICAL COUNTER SECTION3C SCALE 34" = 1'

OPTION 2: TYPICAL SUPPORT DETAIL4 SCALE 34" = 1'

SCALE 38" = 1'

1/4" REVEAL TYP.

FLOOR

2" CORIAN-1W/ EASED EDGES

WALL

LAM-1 LAM-1

1/4" REVEAL TYP.

FLOOR

2" CORIAN-1 TOPW/ EASED EDGES

LAM-1 LAM-1 LAM-1

1/4" REVEAL TYP.

FLOOR

WALL

LAM-1 LAM-1

EXISTING COLUMN 3"x15" BOOK DROP

CUTOUT W/ STAINLESS SLEEVE

BOOK CART BELOW

36"H STAINLESSCORNER GUARDS

112" BLACK LAMINATE

SUPPORT PANEL SET O.C.

1/4" BLACK REVEAL TYP.

FLOOR

U/C MOBILE FILE CABBEYOND (SHOWN ASHERMAN MILLER15"W X 22"D X 27"HNOT PART OF MILLWORK)

REMOVABLE BLACK LAMINATED PLYWOOD PANEL

LAM-2

2 1/2" GROMMET

LAM-1

FLOOR

CORIAN-1 TOPW/ EASED EDGES

BOOK DROP (SHOWN AS 26 W "X 26 D"X 30H" NOT PART OF MILLWORK)

3/4" LAMINATED PLYWOOD

FRAMING BOLTED TO FLOOR @ 24" O.C.

REMOVABLEINTERIOR BLACKLAMINATED PLYWOODTYP.

1/4" BLACKREVEALTYP.

STAINLESS SLEEVE W/ 11

2 " LIP ALL ROUND

EXISTING GYPSUM BOARD PARTITION

LAM. EDGE

COUNTER LAM-1

COUNTER LAM-4

BID SET 01-22-15




COORDINATE W/ ELECTRICIAN THE SECURING OF THE OF EXISTING POWER & I.T. FLOOR CONDUITS & JUNCTION BOXES.

COORDINATE WITH ELECTRICIAN THE LOC. OF

NEW ELECTRICAL POWER & VOICE/DATA CONDUITS

TO BE RUN THROUGHMILLWORK.

COORDINATE WITH ELECTRICIAN THE LOC. OF NEW ELECTRICAL POWER & VOICE/DATA OUTLETS TO BE SECURED TO MILLWORK. TYP.

5" x 60" +/-WALL GUARD@34" O.C. AFF.

5" x 60" +/-WALL GUARD@34" O.C. AFF.

5" x 66" +/- WALL GUARD @34" O.C. AFF.

5" x 66" +/- WALL GUARD @34" O.C. AFF.

juanita e. thornton shepherd park neighborhood library ... · juanita e. thornton | shepherd park...

Documents