jvc xr-d400sl service en

8/16/2019 Jvc Xr-d400sl Service En

1/28

SERVICE MANUAL

ContentsSafety precautions

Technical description

Disassembly method

Troubleshooting

Precaution for servicing

1-2

1-3

1-6

1-9

1-13

MULTIPLE COMPACT DISC RECORDER

PO

WER

1 TRACK ALLREPEAT

SPEED

ERASE

OVER

OPEN/CLOSESOURCE

SPEED

REPEAT FINALIZE

PROGRAM

REC

4x 2x 1x

1

11

2

12

3

13

4

14

5

15

6

16

7

17

8

18

9

19

10

20

OPEN/CLOSE

REC/PLAY

SCSI AUTO REC

XR-D400SL

XR-D400

E Germany

Area Suffix


2/28

R-D400SL

2

Safety precautions

1. This design of this product contains special hardware and many circuits and components speciallyfor safety purposes. For continued protection, no changes should be made to the original design

unless authorized in writing by the manufacturer. Replacement parts must be identical to thoseused in the original circuits. Services should be performed by qualified personnel only.

2. Alterations of the design or circuitry of the product should not be made. Any design alterations ofthe product should not be made. Any design alterations or additions will void the manufacturer`s

warranty and will further relieve the manufacture of responsibility for personal injury or propertydamage resulting therefrom.

3. Many electrical and mechanical parts in the products have special safety-related characteristics.These characteristics are often not evident from visual inspection nor can the protection afforded

by them necessarily be obtained by using replacement components rated for higher voltage,wattage, etc. Replacement parts which have these special safety characteristics are identified inthe Parts List of Service Manual. Electrical components having such features are identified by

shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of asubstitute replacement which does not have the same safety characteristics as the recommended

replacement parts shown in the Parts List of Service Manual may create shock, fire, or otherhazards.

4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and thelike to be separated from live parts, high temperature parts, moving parts and/or sharp edges

for the prevention of electric shock and fire hazard. When service is required, the original leadrouting and dress should be observed, and it should be confirmed that they have been returned

to normal, after re-assembling.

5. Leakage current check (Electrical shock hazard testing)

After re-assembling the product, always perform an isolation check on the exposed metal partsof the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control

shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check.

Plug the AC line cord directly into the AC outlet. Using a "Leakage Current Tester", measure

the leakage current from each exposed metal parts of the cabinet , particularly any exposed

metal part having a return path to the chassis, to a known good earth ground. Any leakagecurrent must not exceed 0.5mA AC (r.m.s.)

Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohmsper volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by

a 0.15 F AC-type capacitor between an exposedmetal part and a known good earth ground.

Measure the AC voltage across the resistor with theAC voltmeter.

Move the resistor connection to each exposed metalpart, particularly any exposed metal part having areturn path to the chassis, and measure the AC

voltage across the resistor. Now reverse the plug in

the AC outlet and repeat each measurement voltagemeasured any must not exceed 0.75 V AC (r.m.s.).This corresponds to 0.5 mA AC (r.m.s.).

Good earth ground

Place thisprobe on

each exposedmetal part.

AC VOLTMETER(Having 1000ohms/volts,or more sensitivity)

1500 10W

0.15 F AC TYPE

! CAUTION Burrs formed during molding may be left over on some parts of the chassis. Therefore,pay attention to such burrs in the case of preforming repair of this system.


3/28


4/28

R-D400SL

4

The XR-D400 incorporates the SCMS (Serial Copy Management System) and the RID (Recorder Unique Identifier)

functions.SCMS is used to limit digital copies to one generation only. The principles are shown in Fig. 3.With RID, the RID codes are written into discs which are as specified in the Orange Book Parts II and III. The

codes contain the manufacturer's name, product name and machine number to enable the tracing of i llegal copies.

Digital recording Digital recording

[Fig. 3] Principles of SCMS

Fig. 4 shows the structure of a CD-R disc.

In recording, a laser beam having the same wavelength as theCD beam (780 nm) but of tens times higher power is irradiated

from the substrate surface to the groove.This irradiation causes thermal deformation of the organic

pigment layer forming pits in it.The organic pigments include cyanine, phtalocyanine and azoicdyes and the reflective layer uses gold or silver materials.

In playback the laser beam reads the pits recorded in thepregroove.

The thermal deformation of the organic pigment layer cannot berecovered to the original condition. As a result, the CD-R discs

cannot be rewritten and only additional writing is possible withthem.

Fig. 5 shows the structure of a CD-RW disc.The CD-RW uses a phase-changing recording material in the

recording layer.With the CD-RW, a laser beam with regulated power andcooling time is irradiated to form a crystalline phase (erased

status) and amorphous phase ( recorded s tate) on thepolygroove and data is reproduced according to the difference in

reflectivity of the two phases.An amorphous state can be obtained by quick cooling after

irradiation by a strong laser beam.The phase-changing recording material is made of a compoundof silver, indium, antimony and tellurium, and rewrit ing is

possible up to about 1000 times.

As the reflectivity at 780 nm of the CD-RW is lower than the CD-R, the RF amp gain should be changed in order to play a CD-RW disc.

SCMS and RID functions

Recording on CD-R discs

Recording on a CD-RW disc

Comparison between the CD-R and the CD-RW

Label printed surface

Protective layer groove

Reflective layer

Organic pigment layer

Substrate

pregrooveTrack pitch

1.6 µm

Laser beam

Signal surface

[Fig. 4]

Printed surface

Protective layer

Aluminum reflective layer

Upper protective layer

Recording layer

Lower protective layer

Substrate

polygroove

Signal surfaceLaser beam

[Fig. 5]

CD-RCompact Disc Recordable

CD-RWCompact Disc Rewritable

Specifications

Laser reflectivity

Recording power

Playback on CD player

Orange Book Part II

65% or more

4 to 11 mW

Possible

Orange Book Part III

15% to 25%

8 to 14 mW

Impossible

[Table 2]


5/28

XR-D40

CD-R/RW

CD-R/RW

Lead-in areaThis area records the TOC (Table Of Contents) including the number of tracks in the disc, track-start position

information, etc.

DataThis area contains the recording of actual audio signals, file data, etc.The unit used in the data area is the track. Usually, music CDs use a track per song selection while the CD-

ROM discs basically uses only one track.

Lead-outThis area is used to indicate that the data in the disc has reached the end.

The combination of the lead-in, data and lead-out areas is referred to as a single session.A disc containing multiple sessions is called a multi-session disc. The CD-EXTRA belongs to this kind of disc.

PCA (Power Calibration Area)This area is used to regulate the laser power in data writing.

Its data optimizes laser power according to external factors such as the medium type, supply voltage andoperating temperature. The PCA provides an area for use in 99 times of test writing.

PMA (Program Memory Area)This area contains the recording of the start and end positions of the tracks. When a disc is not finalized in

program recording, this area is used to obtain the preliminary TOC data.

PMA Track 1

Track 1

Track 1

Track 2

Track 2 Lead-out

PMA

PMA Lead-in

Recording method of the CD-R/RW

As shown in Fig. 6, the recording areas of a CD-ROM and a CD-R/RW are different.These discs use two recording areas in addition to the areas used for data recording by ordinary CD discs.

Finalization

Finalization refers to writing the preliminary TOC data in the PMA into the lead-in and lead-out areas.When a disc is not finalized, its TOC data is recorded exclusively in the PMA.

Since ordinary CD players cannot read the PCA and PMA, non-finalized discs can be read only with aREC/PLAY machine such as the XR-D400. This makes possible addition writing on the disc.When a disc is finalized, its lead-in, data and lead-out areas are written properly and the disc becomes a disc

complying with the Orange Book specifications.Fig. 7 shows the finalization procedure.

2 areas for CD-ROM

Inner direction Outer direction

PCA PMA Lead-in Data Lead-out

[Fig. 6]

[Fig. 7]

Before finalization

Track rewriting

After finalization

(Preliminary TOC)

TOC data


6/28

R-D400SL

6

1. Remove the 4 screws A from both sides of the top cover.

2. Remove the 4 screws B from the rear of the top cover, thenremove the stop cover.

Disassembly method

Removing the top cover (Figs. 1 & 2)

1. Remove the top cover.

2. Remove the 3 screws C that retain the front panel from thebottom. (Fig. 3)

3. Unplug the connector A from the power supply board (Fig. 4)

and the flat wire from the control board (Fig. 5).

4. Disengage the 2 claws D from the front panel and removethe front panel. (Figs. 4 and 5)

Removing the front panel (Figs. 3 to 5)

1. Remove the stop cover.

2. Unplug connector B from the power supply board (Fig. 4).

3. Remove the 6 screws E from the rear panel (Fig. 6).

4. Remove the 2 screws F retaining the SCSI connector, thenremove the rear panel.

(CAUTION) Screw F retaining the SCSI connector functions toprotect the connector. Be sure to remove it as alast task in disassembly or a first one in assembly.

Removing the rear panel (Figs. 4 & 6)

Front panel

Connector BConnector A

Flat wire

A

A

B

B

C

DD

G

G G

G

Fig. 1

Fig. 2

Fig. 3

Fig. 5Fig. 4


7/28

XR-D40

F

E

E

CD-ROM drive

CD-R/RW drivePower supply

connectors

Control cable

Audio signal connector

H

H

Flat cable

Flat cable

Connector

I

I


2. Remove the rear panel.

3. Unplug the connectors from the drives (CD-ROM drive:

power supply connector and control cable connector.CD-R/RW drive: power supply connector, control cable

connector and audio signal connector). (Fig. 7)4. Remove a total of 8 screws retaining the drives, from

the side panels. (Figs. 4 and 5)

5. Take out each drive in the rear direction.

Removing the CD-ROM and CD-R/RW drives(Figs. 4, 5 and 7)

1. Remove the top cover.2. Remove the rear panel.

3. Remove the CD-R/RW drive.

4. Remove the 6 screws H retaining the cover, then remove

the cover. (Figs. 8 and 9)

5. Stand up the board and unplug the 2 flat cables and 1connector. (Fig. 10)

6. Remove the 4 screws I retaining the circuit board. (Fig. 11)

7. Unplug 1 flat cable and remove the circuit board. (Fig. 12)

Removing the CD-R/RW drive board(Figs. 8 to 12)

Fig. 6

Fig. 7

Fig.8

Fig. 9

Fig. 12

Fig. 10

Fig. 11


8/28

R-D400SL

8

JJ

CD-ROM drive

CD-R/RW drive

Tray eject hole

Tray eject hole


2. Remove the front panel.

3. Remove the 13 screws J retaining the board.

Removing the front board (Fig. 13)


2. Remove the front panel.

3. When removing a disc from the CD-ROM drive (upper

drive), insert a thin wire or similar object into the trayeject hole at the right end of the drive. When the drive

comes out, pull it out toward the front.

4. When removing a disc from the CD-R/RW drive (lowerdrive), insert a thin wire or similar object into the tray

eject hole at the left end of the drive. When the drivecomes out, pull it out toward the front.

Removing the disc (Fig. 14)Fig. 13

Fig. 14


9/28

XR-D40

NO

YES

YES

NO

OK

NO

NO

NO

NO

YES

YES

YES

YES

YES

YES

YES

NO

NO

Troubleshooting (For repairing the audio CD dubbing)

POWER button ONCheck the CN991 and S1034

on the Front board.

Does the POWERindicator light?

Are the pins and of the CN991on the Front board short-circuited

Go to the "PowerSupply Operation".

Can the tray beopened/closed with theOPEN/CLOSE button?

Go to the"OPEN/CLOSE Operation".

Can the SOURCE disc

drive read theTOC of the CD?

Go to the

"Reproduction Operation"

Can the REC/PLAY discdrive play the CD?

Is the audio output fromthe CD in the REC/PLAY

disc drive?

Can the data be written

in the REC/PLAYdisc drive?

Are the front keys andindicators normal?

Check the general

operations.

Go to the"Audio Operation".

Go to the

"Write Operation".

Go to the "Front Key /Indicator Operation".


10/28

R-D400SL

10

CN991 section

(Note) Connection points of the 4 wires.

Do not disconnect anyother connections.

YES YES

YES

YES

YES

NO

NO

NO

First remove the 4 wires connected to the Power Supply unit (QAL0244-002) (see photo below) to do a check

of the stand-alone mode.(1) Press the POWER button to ON, and check the voltages at the leftmost wire (red, DC +5 V) and the

rightmost wire (yellow, DC +12 V).Then connect the wires and check the voltages as described below.

(1) Check the continuity between the GND line and leftmost wire (red, DC +5 V) and the rightmost wire (yellow,+12 V) to ensure that there is no short-circuiting.

(2) Press the POWER button to ON and check the voltages at the leftmost wire (red, DC +5 V) and therightmost wire (yellow, DC +12 V).If the CD voltage drops abnormally or the protection device (fuse, etc.) is released when the wires are

connected (i.e. load is applied), there may be short-circuiting on the load side or in the connection path.

Power supply operation

OPEN/CLOSE operation

Press theOPEN/CLOSE button.

OPEN/CLOSEoperation is OK.

Is DC powersupply normal?

Does the trayopen or close?

Can other buttons

be used?

Can the tray beopened/closed by the

OPEN/CLOSE button in the

stand-alone mode.

Check connections ofCN602, CN603 and

drives.Check the Front and

Control boards.

Check connections ofCN111 and CN001.

Check the Front andControl boards.

Check the connections

of CN602, CN603 andthe drives.

Go to the"Power Supply Operation".

In the stand-alone mode theOPEN/CLOSE button can be

pressed by removing thefront panel.

CD-ROM

drive

CD-R/RWdrive


11/28

XR-D40

Note 1) The access condition of each drive is shown by an indicator.

Blinking: The disc TOC data is being read.Lighting: The disc TOC data has been read or is being reproduced.

Note 2) The TOC data of the disc in the SOURCE disc tray (CD-ROM drive) can be displayed as follows.

When the SOURCE indicator stops blinking and starts constant lighting, press the skip button (rewinddirection) to display the number of tracks on the disc.

Examples) CTS-1000 Disc with 28 tracks: Track indicators 1 to 20 (Green) and the OVER indicator (Red) lights.Other Disc with 12 tracks: Track indicators 1 to 12 (Green) light.

Reproduction operation

Audio operation

Insert a disc.

Can the TOC be read?

Is playback possible? Applicable to REC/PLAY disc tray only.

Reproduction

operation is OK.

Check the connections of

the CN602, CN603 anddrives.

Check the drives.

Check buttons.Check the CD-R/RW drive.

YES

YES

YES

NO

NO NO

YES

NO

NO

During playback

Is audio output?

Audio operation is normal.

Is the audio freefrom noise orsound skip?

Is audio normalat CN401 on

Control board?

Check the surroundingsof J401 on the IC401.

Check the 3-pin wireconnections.

Replace HQA-030A. Replace HXL-3BSPA.


12/28

R-D400SL

12

The REC/PLAY disc tray (CD-R/RW drive) is composed of the mechanism unit (HXL-3BSPA) and the boardass'y (HQA-030A).Therefore, in case of a write failure, check the following points first before proceeding to the next step.

The trouble is not due to the disc defect.

The FPC cable connecting the mechanism unit and the board ass'y is not disconnected or unplugged.

1. Symptoms, which may be due to a defect in the mechanism unit (HXL-3BSPA)

(1) There is no trace of writing on the CD-R/RW disc.(2) Error during write.

(3) Rotation stopped during write.(4) Write completes normally but the written disc cannot be reproduced.

(5) Either the CD-R or the CD-RW disc cannot be written onto.(6) Disc cannot be recognized as a recordable CD-R/RW disc.

(7) Abnormal noise from the mechanism during disc rotation.(8) Disc will not rotate.(9) Disc rotation is unstable (the rotation speed increases suddenly).

2. Symptoms, which may be due to a defect in the board ass'y (HQA-030A)

(1) Write operation will not start.(2) Disc will not rotate.

(3) The access LEDs do not light or blink.

Write operation

Front Key/Indicator operation

Press thePOWER button ON.

Are the keyoperations normal?

Are theindicators normal?

Front key and indicatoroperations are OK.

Are theconnections of the

CN001 andCN111 normal?

Check Front and

Control boards.

Connect the

CN001 and CN111.

YES

YES

YES

NO

NO NO


13/28

XR-D40

Precaution for servicing

Handling of board ass'y in REC/PLAY disc tray

After replacing the board ass'y (HAQ-030A), be sure to modify it for use with the XR-D400SL by performing

the following operations:

1. Remove 3 condensers and confirm the jumper settings.2. Rewrite the firmware for XR-D400SL.

Note) The HQA-030A is not a part designed exclusively for the XR-D400.

1. Remove 3 condensers and confirm the jumper settings.

(1) Remove the condensers C429, C430 and C432 (for their locations, see Figs. 1 and 2).

[Fig. 1]

[Fig. 2]

[Fig. 3] [Fig. 4]

(2) Confirm the jumper settings.The settings should be as shown in Fig. 3 and 4. The jumper should be inserted into the rightmost hole

when the board is seen from the rear.

2. Rewrite the firmware for XR-D400

A PC and firmware software are required to rewrite the firmware.

Create a folder in the hard disk of the PC and store both of these in the same folder.

Applicable PC

Firmware software

OS Windows 95/98CPU Pentium 133 MHz or higherMemory 16 MB or moreModel IBM compatible machine

Firmware software Download.exe

Firmware Zcp133s.hex


14/28

R-D400SL

14

Rewrite procedure

(1) Connect the REC/PLAY disc tray in the stand-alone mode to thePC. (Fig. 5)Note) The PC connection procedure will be described later.

(2) While holding down the switch on the right of the front panel(encircled in Fig. 5), boot the PC.

(3) Keep holding down the above switch until Windows has started up.

(4) Run firmware software Download.exe.

(5) When the firmware software screen appears (Fig. 6), confirm that;the Vendor is JVC, the product is XR-W4424 and the Version is 1.00.Note) If another content than the above is displayed, restart the operation

from step (2).

(6) After confirming that the BUS Type is ATAPI and that Create is checked, click the Updatebutton. (Fig. 6)

(7) When the screen as shown in Fig. 7 is displayed, select Zcp133s.hex, and click the OKbutton.

(8) The firmware rewriting starts and the access LED on the front panel changes from amber

lighting to amber blinking.Rewriting takes about 60 seconds. The extinction of the access LED indicates thecompletion of the firmware rewriting.

(9) When the screen in Fig. 6 is displayed again, click Close to close the firmware software.

[Fig. 5]

[Fig. 6]

[Fig. 8]

[Fig. 9]

[Fig. 7]

Firmware version check procedure(1) Boot the PC.

Note)If this procedure is started immediately after the rewriting procedure above, do notsimply restart the PC but be sure to switch it off and then on again.

(2) Open the Device Manager.Click [Start] R [SettingR [Control Panel] R [System].

Select [Device Manager] and click [CD-ROM].

(3) When the screen shown in Fig. 8 is displayed, select JVC XR-RWD400S.

(4) Open the Properties of JVC XR-RWD400S and select Setting.

(5) Confirm that the firmware revision number is 1.33. (Fig. 9)


15/28


16/28No.A0001

VICTOR COMPANY OF JAPAN, LIMITED

OPTICAL DISC BUSINESS DIV. PERSONAL & MOBILE NETWORK BUSINESS UNIT

AV & MULTIMEDIA COMPANY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan

Printed in Ja200009 (S)

R-D400SL


17/28

XR-D400SL

2-1

Block diagram

CD-ROM DRIVE ASSY POWER SUPPLY ASSY AC

Q AL02335 QA L0244 100V

POWER DC +12V(YELLOW)

SUPPLY

4 PIN DC +5V(RED)

ATAPI I/O

40 PIN

2 PIN

CD-R/RW DRIVE ASSY

CONTROL PCB ASSY FRONT PCB ASSY CN911

LOADER ASSY MAIN PCB ASSY LEA10014 CN501 LEA10012 S1034

HXL-3BSPA 27 PIN HQA-030 CN401 CN602 CN001 CN111 POWER SW

POWER ATAPI 21 PIN

SUB PCB UNIT CN107 CN407 SUPPLY I/O

IC101

IC101 u-COM

PRE AMP CN108 CN408 CN401 CN603 CN201 IC991 IC992

ATAPI 40 PIN ATAPI SCSI LED DRIVER

I/O I/O IC201 INTERFACE

CN101 27 PIN SCSI CONVERTER

50 PIN LED

LASER IC403 IC401

PICK-UP CN405 DAC S202 SCSI

ID SW

SPINDLE MOTOR CN401

FEED MOTOR 18 PIN J401

IC417 AUDIO OUT

LOADING MOTOR CN402 3 PIN

OPEN/CLOSE SW AUDIO OUT

CN401

LOADER UNIT 5 PIN


18/28


19/28

6

5

4

3

2

1

B C D E F G H I JA

7

XR-D400SL

2-3

Control circuit


20/28

6

5

4

3

2

1

B C D E F G H I JA

7

XR-D400SL

2-4

Board interconnection


21/28

6

5

4

3

2

1

B C D E F G H I JA

7

XR-D400SL

2-5

Printed circuit boards Control board

(Surface side)

TP311

TP309

TP187

TP310

TP100

T P 1 0 1 T P 1 0 2

T P 1 0 3 T P 1 0 4

TP105

TP106

TP107

TP108

TP109

TP110

T P 1 1 1

TP112

T P 1 1 3

TP114

TP115

T P 1 1 6 T P 1 1 7

T P 1 1 8

T P 1 1 9

T P 1 2 0

T P 1 2 1

T P 1 2 2

T P 1 2 3

TP124

TP125

TP126

TP127

TP128TP129TP130TP131

TP132

TP133TP134

TP135

TP136

TP137

TP138

TP139 TP140

TP141

TP142

TP143

TP144

TP145

TP146

TP147

TP148

TP149

TP150

TP151

TP152

T P 1 5 3

T P 1 5 4

TP155

TP156

TP157

T P 1 5 8

TP159TP160

TP161

TP162

TP163

TP164

TP165

TP166

TP167

TP168

T P 1 6 9

T P 1 7 0

T P 1 7 1 T P 1 7 2

T P 1 7 3 T P 1 7 4

T P 1 7 5 T P 1 7 6

TP177

TP179

TP180

TP181

TP182

TP183

TP184

TP185

TP186

TP188

TP189

TP190

TP191

TP192

TP193

TP197

TP198

TP199

TP201

TP202

TP203

TP204

T P 2 0 5

T P 2 0 6

TP207

T P 2 0 8

T P 2 0 9

T P 2 1 0

T P 2 1 1

T P 2 1 2

T P 2 1 3

T P 2 1 4

T P 2 1 5

T P 2 1 6

T P 2 1 7

T P 2 1 8

T P 2 1 9

T P 2 2 0

T P 2 2 1

T P 2 2 2

T P 2 2 3

T P 2 2 4

T P 2 2 5

TP226

T P 2 2 7

TP228

TP229 T P 2 3 0

TP231

T P 2 3 2

TP233

T P 2 3 4

TP235

TP236

TP237

TP238

T P 2 3 9

TP240TP241

T P 2 4 2

TP243

T P 2 4 4

TP245

TP246

T P 2 4 7

T P 2 4 8

TP249

TP250TP251

TP252

T P 2 5 3

TP254

T P 2 5 6

TP257

T P 2 5 8

T P 2 5 9

TP301

TP302

TP303

TP304

TP305

TP306

TP307

TP308

TP401

TP402

TP403

TP404

TP405

TP406

TP407

TP408

TP409

TP410

TP411

TP412

TP413

TP414

TP415

TP416

TP417

TP418

TP419

TP420

TP421

TP422

TP423 TP424

TP425

TP426

TP501 TP502

TP503

TP504

TP505TP507

TP509

T P 6 0 1

T P 6 0 2

T P 6 0 3

T P 6 0 4

T P 6 0 5

TP606

TP607

TP608

T P 6 0 9

TP610

T P 6 1 1

TP613

TP431

TP616

TP617

TP618

TP619

CN202

T P 6 2 1

T P 6 2 2

T P 6 2 3

T P 6 2 4

T P 6 2 6

T P 6 2 7

T P 6 2 8

T P 6 2 9

T P 6 3 0

T P 6 3 1

T P 6 3 2

T P 6 3 3

T P 6 3 4

T P 6 3 5

T P 6 3 6

T P 6 3 7

T P 6 3 8

T P 6 3 9

T P 6 4 0

T P 6 4 1

T P 6 4 2

T P 6 4 3

T P 6 4 4

T P 6 4 5

T P 6 4 6

T P 6 4 7

T P 6 4 8

T P 6 4 9

T P 6 5 0

T P 6 5 1

T P 6 5 2

T P 6 5 3

T P 6 5 4

T P 6 5 5

T P 6 5 6

T P 6 5 7

T P 6 5 8

T P 6 5 9

T P 6 6 0

T

P 6 6 1

T P 6 6 2

T P 6 6 3

T P 6 6 4

T P 6 6 5

T P 6 6 6

T P 6 6 7

T P 6 6 8

T P 6 6 9

T P 6 7 0

T P 6 7 1

T P 6 7 2

T P 6 7 3

T P 6 7 4

T P 6 7 5

T P 6 7 6

T P 6 7 7

T P 6 7 8

TP679

T P 6 8 0

TP432

TP625

T P 2 6 0

TP433

TP681

TP682

TP261

T P 5 1 2

TP683

TP684

TP685

TP262

TP264

TP265

TP511

T P6 15 T P6 1 2

TP614

TP620

(Bottom side)


22/28

6

5

4

3

2

1

B C D E F G H I JA

7

XR-D400SL

2-6

C1101

C1102

C1104

C1105

CN111

D 10 01 D 10 02 D1003 D1004 D 10 05 D 10 06 D1 007 D1008 D1009 D1010

D1011

D1012

D1013D1014 D1015 D1 01 6 D 10 17 D1 01 8 D 10 19 D1020 D1021

D1022

D1023 D1024 D1025

D1026 D1027 D1028

D1029

D1030

D1031

D 1 0 3 2

I C 9 9 1

I C 9 9 2

Q1011Q1012

Q1013 Q1014

Q1015

Q1016

Q1017

Q1018

Q1019

Q1020

Q1031

Q1032

R1001 R1002 R1003 R1004 R1005 R1006 R1007 R1008 R1009 R1010

R1011 R 1012 R1013 R1014R 1 0 1 5

R1016R1017

R1018R1019

R 1 0 2 0 R1021

R1022

R1023 R1024 R1025

R1026 R 10 2 7 R 1 02 8

R1029

R1030

R1031

R1032

R1101

R1102

R1103

S 10 01 S 10 02 S1003 S1004 S1005S1006S1007S1008 S1009 S1010

S1011S1012S1013 S1014 S1015 S1016 S1017S1018S1019S1020

S1021

S1022

S1023S1024

S1025

S1026

S1027 S1028S1029S1030S1031S1032

S1034

T P 9 0 1

TP902

TP903

T P 9 0 4

T P 9 0 5

T P 9 0 6

T P 9 0 7

T P 9 0 8 T

P 9 0 9

T P 9 1 0

T P 9 1 1

T P 9 1 2

T P 9 1 3

T P 9 1 4

T P 9 1 5

T P 9 1 6

T P 9 1 7

T P 9 1 8

T P 9 1 9

T P 9 2 0

T P 9 2 1

T P 9 2 2

T P 9 2 3

T P 9 2 4

TP925

T P 9 2 6

TP927

TP928

TP929

TP930

TP931T P 9 3 2

TP933T P 9 3 4

TP935

TP936

T P 9 3 7

TP938

TP939

T P 9 4 0

TP941

T P 9 4 2

TP943

TP944

T P 9 4 5

TP946

TP947

TP948

TP949 TP950

TP951T P 9 5 2

TP953

TP954

TP955

TP956

T P 9 5 7

TP958 T

P 9 5 9

T P 9 6 0

T P 9 6 1

TP962

TP963 TP964

T P 9 6 5

TP966

TP967

TP968TP969

T P 9 7 0

T P 9 7 1

TP972

TP973

TP974

TP975

TP976

TP977

CN991

Front board


23/28

XR-D40

PARTS LIST

[ XR-D400SL ]

- Contents -

Exploded view of general assembly and parts listCR-R/RW mechanism assembly and parts list

Packing materials and accessories parts list

3-33-5

3-6

Area suffix

E ----------------- Germany


24/28

R-D400SL

2

MEMO


25/28

XR-D400SL

3-3

2

5

4

16

20

3

1517 13

12

20

25

35

24

21

21

7

829

30

32

27

38

40

20

9

33

33

34

31

23

41

42

28

18

16

1

10

11

14

6

22

Exploded view of general assembly and parts list

26

26

19

19

37

3736

36

20

20

26

20

20

2026

Block No. M1MM


26/28

XR-D400SL

3-4

Item Parts number Parts name AreaA

Parts list ( General Assembly )

Q'ty Description

Block No.

01 LE10227-001B FRONT PANEL 1

02 LE30810-005A WINDOW SCREEN 1

03 E75896-228 SPACER 2

04 LE20500-002A DO OR 1

05 LE20506-001A DOOR(ROM) 1

06 LE40651-001A TEN.SPRING 2

07 LE10226-001B CHASSIS BASE 1

08 E47227-008 FO O T 2

09 QYSBSG3010M T.SCREW 2

10 LE30818-002A PUSH BUTTON(5) 1

11 LE40650-002A COMP.SPRING 1



14 LE30814-001A P BUTTON(3)ASSY 1


16 LE30812-001A INDICATOR(1) 4

17 LE30813-001A INDICATOR(2) 1

18 LE30840-001A INDICATOR(4) 20

19 QYSBSF2608Z T.SCREW 13

20 QYSBSG3008Z T.SCREW 17

21 LE20503-001B SIDE BKT 2

22 LE40729-001A LUG 1

23 --- CD-ROM DRIVE 1

24 QAL0235-001 CD-ROM DRIVE 1

25 LE20505-001A FITTING 1

26 QYSPSP3006Z T.SCREW 8

27 LE20504-001B PCB BKT 1

28 QAL0244-002 P OWE R P CBA 1

29 LE20496-001A REAR PANEL 1

30 WJ Z004 8-0 02A A C I NL ETA 1

31 QYBNSP4008M BOLT 1

32 QYNFS4000Z NUT 1

33 QYSBSGY3008M SPECIAL SCREW 6

34 QYSHSP3006N T.SCREW 2

35 LE20497-002A METAL COVER 1

36 QYSBSGY3008N SPECIAL SCREW 4

37 E406308-004 SPECIAL SCREW 4

38 QUQ412-2118CJ FLAT WIRE 1

40 L EA10012-01A FRO NT P WB A SSY 1

41 L EA10014-01A CONTRL PWB ASSY 1

42 WJJ0150-001A WIRE ASSY 1

See Page 3-5


27/28

XR-D40


Parts list

Q'ty Description

Block No. M2MM

01 HQ200031-001 UPPER CASE 1

02 HQ200032-001 BOTTOM COVER 1

03 HXL-3BSPA LOADER MECHA 1

04 QUQ105-2705AB FLAT WIRE 2

05 HQ400090-001 INSULATOR SHEET 1

06 HQA-030A MAIN.P.C.B.ASSY 1

07 HQ400127-001 INSULATOR 4

08 HQ400089-001 INSULATOR 4

09 HQZ0073-001 SIL ICON SHEET 2

10 HQ400113-001 SPECIAL SCREW 4

11 SSSP2004N SC R EW 6

See page 1-13

C N 1 0 8

C N 1 0 7

5

77

2

9

6

4

10

10

3

8

11

11

1

Block No. M2MM

CD-R/RW mechanism assembly and parts list


28/28

R-D400SL

Packing materials and accessories parts listBlock No. M3MMBlock No. M4MM

6

1

2

4

3

5


Packing list

Q'ty Description

Block No. M3MM

1 LE10236-001A P.CASE 1

2 LE20509-001A P.PAD(L) 1

3 LE20508-001A P.PAD(U) 1

4 QPC05006515P POLY BAG 1

5 LE30830-201A PARTSBOX 1

6 LE40681-001A ACCESSORY LABEL 1


Accessories parts list

Q'ty Description

Block No. M4MM

1 LET0169-001A I.BOOK 1

2 LET0174-001A I.BOOK 1

3 QMPL110-200-JQ PO WE R C OR DA 1

4 EWP302-011W SIGNAL CORD 1

5 BT-54008-2 WARRANTY CARD 1

6 LE40732 003A CAUTION SHEET 1

jvc xr-d400sl service en

Documents